表面改性对CeO2纳米粉体特性的影响

研究了表面改性对CeO2纳米粉体特性的影响，采用表面活性剂．十二烷基硫酸钠对CeO2粉末颗粒表面进行了改性。未改性和改性的纳米氧化铈用粉体综合性能测试仪、激光粒度仪、比表面积测试仪、X射线仪、扫描电子显微镜进行了表征。结果表明，用十二烷基硫酸钠表面改性能提高纳米氧化铈的流动性和分散性，减小比表面积和团聚，同时也对CeO2粉体颗粒表面改性的机制进行了探讨。     

共沸蒸馏法制备表面化学改性氢氧化镁纳米颗粒

首次将表面改性剂如硬脂酸、硬脂酸锌或稀土偶联剂加入到传统的共沸蒸馏体系中,使Mg(OH)2纳米颗粒的表面改性和干燥过程同时完成。通过XRD、TEM、FT-IR、TG和CAM(接触角测试)等技术手段对样品的结构、形貌和性质进行了表征。结果表明,表面改性剂不但能够和Mg(OH)2纳米颗粒的表面的OH-离子发生化学反应形成表面修饰层,减少硬团聚现象,而且还使纳米颗粒表面由亲水性变为疏水性。另外,对共沸蒸馏法制备表面改性纳米颗粒的机理进行了讨论,为纳米颗粒表面改性提供了一种新思路。     

Fe3O4纳米颗粒的表面改性

通过实验对Fe3O4纳米颗粒表面改性的最佳条件进行了摸索.并根据表面改性的包覆机理对不同酸度,温度和表面活性剂的用量对Fe3O4纳米颗粒的尺寸,磁性和稳定性的影响进行了理论上的分析.     

纳米锰锌铁氧体的制备及在TPV中的应用

采用化学共沉淀法制备纳米锰锌铁氧体纳米颗粒,并用油酸进行表面改性,有效地阻止了纳米颗粒的团聚;改性后团聚体的粒径明显减小,提高了其在TPV中的分散性.将制备好的纳米颗粒作为填料改性TPV,通过一系列试验发现,油酸改性的锰锌铁氧体纳米颗粒比未改性的纳米颗粒更能提高TPV的拉伸强度和断裂伸长率.     

纳米氧化锌的机械力化学表面改性

采用机械力化学表面改性工艺,以硬脂酸为改性剂,在气流粉碎机中对纳米氧化锌进行解团聚和表面改性,并借助SEM、XRD、FF—IR和XPS对改性前后的氧化锌粉体进行结构表征．结果表明：硬脂酸分子化学键合在氧化锌表面．改性前后氧化锌的晶体结构相同,其颗粒的团聚性降低,二次粒径明显减小．通过测定改性样品的活化指数和亲油化度,选择最佳的改性剂用量为氧化锌质量的10％,氧化锌表面亲油疏水,在有机溶剂中有较好的分散性．     

纳米微晶纤维素表面改性研究

分别对纳米微晶纤维素(NCC)的表面进行醋酸酯化、羟乙基化和羟丙基化改性,利用FT-IR、TEM、13C-NMR、TGA对改性产物进行表征,研究不同的表面改性方法对纳米微晶纤维素性能的影响.结果表明,利用这几种方法改性后的NCC,经干燥后都可以重新分散在适当的溶剂中,且颗粒粒径没有明显变化,但不同改性产物的热性能有所差异.     

不同聚合物对纳米SiO2表面改性的研究进展

纳米SiO2由于具有无味、无毒、无污染等特性,因而被广泛用作无机纳米填料。纳米SiO2极易团聚,从而限制了它的广泛应用。但纳米SiO2表面富含大量的硅羟基,可对其进行表面改性。纳米SiO2表面改性的方法较多,主要有表面物理改性和表面化学改性两种,其中表面化学改性中又以聚合物改性的效果最好。本文综述了国内外利用不同的聚合物——亲水性、疏水性和两亲性聚合物对纳米SiO2表面的化学改性,并对其应用进行了分析,展望了其发展前景。     

改性二氧化硅纳米颗粒提高二氧化碳泡沫稳定性的研究

通过纳米二氧化硅的硅烷化改性, 使其在高矿化度盐水中可以稳定存在的前提下, 研究了改性纳米颗粒与阳离子表面活性剂十二烷基三甲基氯化铵混合体系的溶液稳定性及协同稳定CO₂泡沫的效果. 研究结果表明, 无机盐离子对改性纳米颗粒与阳离子表面活性剂间的静电吸引力具有屏蔽作用, 且矿化度越高, 屏蔽效果越明显, 从而混合溶液更易于在高盐水中稳定; 纳米颗粒表面的活性剂吸附层受二者浓度的影响, 进而影响了颗粒的亲/疏水性; 当混合体系中的表面活性剂浓度低于临界胶束浓度(CMC)时, 混合溶液与CO₂的界面张力高于单独活性剂溶液, 而当活性剂浓度高于CMC时, 对CO₂-溶液界面张力几乎无影响, 最低界面张力可降至6 mN/m左右; 改性纳米颗粒的加入可以进一步提高CO₂体相泡沫半衰期一倍以上, 但受二者浓度比例的影响; 纳米颗粒的加入有效提高了多孔介质中泡沫的表观黏度, 最大增幅由20 mPa·s增至55 mPa·s左右, 泡沫黏度增加接近3倍, 增强了CO₂泡沫驱的封堵作用.     

纳米二氧化硅的表面改性研究

以γ-缩水甘油醚丙基三甲氧基硅烷(GPTMS)对酸催化水解正硅酸乙酯(TEOS)聚合得到的纳米二氧化硅胶粒表面进行接枝改性,用激光粒径仪测定二氧化硅颗粒的粒径,并用透射电子显微镜(TEM)观察了改性前后二氧化硅胶粒的分散状况,采用傅立叶红外(FTIR)光谱法对改性前后的二氧化硅粉体进行了分析,通过热失重分析(TGA)法对GPTMS接枝改性二氧化硅胶粒表面的接枝度进行分析计算,同时对颗粒溶胶的ζ电位进行了测试,结果表明:改性后二氧化硅胶粒分散性大大提高,硅烷偶联剂浓度对接枝度有显著影响,当GPTMS的浓度为1mL/S iO2(g)时,接枝度达到最大,且颗粒表面的物理化学性能发生显著变化。     

纳米氧化锌的合成及表面改性

以硫酸锌、尿素为原料,采用均相沉淀法合成了纳米氧化锌.研究了硬脂酸对所制的纳米氧化锌粉体表面改性的机理及其对粉体亲油性的影响.实验结果表明,硬脂酸中的羧基与纳米氧化锌粉体颗粒表面的羟基发生了酯化反应,并在表面形成单分子膜.经过表面改性的纳米氧化锌由亲水性转化为亲油性.同时,就纳米氧化锌粉体硬脂酸表面改性反应,探讨了反应摩尔分数、反应温度和反应时间对产物的影响,从而筛选出粉体亲油性最大的反应条件为:硬脂酸质量分数为7%;反应温度为50℃;反应时间为1h.     

KCl-KBO2-K2CO3, K2MoO4-KBO2-K2CO3, and K2WO4-KBO2-K2CO3 ternary systems

phase diagrams of KCl-KBO₂-K₂CO₃, K₂MoO₄-KBO₂-K₂CO₃, and K₂WO₄-KBO₂-K₂CO₃ ternary systems were studied by a calculation-experimental method and differential thermal analysis (DTA). The coordinates of ternary eutectics were determined to be E ₁: 622°C, 8.5 mol % KBO₂, 56.5 mol % KCl, and 35 mol % K₂CO₃; E ₂: 710°C, 23 mol % KBO₂, 43 mol % K₂CO₃, and 34 mol % K₂MoO₄; E ₃: 710°C, 23 mol % KBO₂, 43 mol % K₂CO₃, and 34 mol % K₂WO₄. The specific heats of melting of the eutectics were determined.     

Phase relations in the K2W2O7-K2WO4-KPO3-Bi2O3 system and structure of K6.5Bi2.5W4P6O34

The phase relations in the cross-section of the K₂W₂O₇-K₂WO₄-KPO₃ containing 15 mol% Bi₂O₃ were undertaken using flux method. Crystallization fields of K_6.5Bi_2.5W₄P₆O₃₄, K₂Bi(PO₄)(WO₄), Bi₂WO₆, KBi(WO₄)₂ and their cocrystallization areas were identified. Novel phase K_6.5Bi_2.5W₄P₆O₃₄ was characterized by single-crystal X-ray diffraction: sp. gr. P−1, a=9.4170(5), b=9.7166(4), c=17.6050(7) Å, α=90.052(5)°, β=103.880(5)° and γ=90.125(5)°. It has a layered structure, which contains {K₇Bi₅W₈P₁₂O₆₈}_∞ layers stacked parallel to ab plane and sheets composed by potassium atoms separating these layers. Sandwich-like {K₇Bi₅W₈P₁₂O₆₈}_∞ layers are assembled from [W₂P₂O₁₃]_∞ and [BiPO₄]_∞ building units, and are penetrated by tunnels with K/Bi atoms inside. FTIR-spectra of K₂Bi(PO₄)(WO₄) and K_6.5Bi_2.5W₄P₆O₃₄ were discussed on the basis of factor group theory.     

Sol-gel synthesis of K3InF6 and structural characterization of K2InC10O10H6F9, K3InC12O14H4F18 and K3InC12O12F18

K₃InF₆ is synthesized by a sol-gel route starting from indium and potassium acetates dissolved in isopropanol in the stoichiometry 1:3, with trifluoroacetic acid as fluorinating agent. The crystal structures of the organic precursors were solved by X-ray diffraction methods on single crystals. Three organic compounds were isolated and identified: K₂InC₁₀O₁₀H₆F₉, K₃InC₁₂O₁₄H₄F₁₈ and K₃InC₁₂O₁₂F₁₈. The first one, deficient in potassium in comparison with the initial stoichiometry, is unstable. In its crystal structure, acetate as well as trifluoroacetate anions are coordinated to the indium atom. The two other precursors are obtained, respectively, by quick and slow evaporation of the solution. They correspond to the final organic compounds, which give K₃InF₆ by decomposition at high temperature. The crystal structure of K₃InC₁₂O₁₄H₄F₁₈ is characterized by complex anions [In(CF₃COO)₄(OH_x)₂]^(5−2x)− and isolated [CF₃COOH_2−x]^(x−1)− molecules with x=2 or 1, surrounded by K⁺ cations. The crystal structure of K₃InC₁₂O₁₂F₁₈ is only constituted by complex anions [In(CF₃COO)₆]³⁻ and K⁺ cations. For all these compounds, potassium cations ensure only the electroneutrality of the structure. IR spectra of K₂InC₁₀O₁₀H₆F₉ and K₃InC₁₂O₁₂F₁₈ were also performed at room temperature on pulverized crystals.     

Solubility in the Na2Cr2O7-(NH4)2Cr2O7-K2Cr2O7-H2O system

Solubility in the Na₂Cr₂O₇-(NH₄)₂Cr₂O₇-K₂Cr₂O₇-H₂O four-component water-salt system at 25, 50, and 75°C was studied for the first time. Phase field boundaries for individual salts and potassium and ammonium dichromate solid solutions, monovariant lines, and invariant points were determined. Experimental data were used to optimize the looped isohydric process of potassium dichromate preparation involving additional salts.     

NaBO2-NaCl-Na2CO3, NaBO2- Na2CO3-NaMoO4, NaBO2- Na2CO3-NaWO4, and NaBO2-NaCl-Na2WO4 ternary systems

The phase diagrams of the NaBO₂-NaCl-Na₂CO₃, NaBO₂-Na₂CO₃-Na₂MoO₄, NaBO₂- Na₂CO₃-Na₂WO₄, and NaBO₂-NaCl-Na₂WO₄ ternary systems were studied by a calculation-experimental method and differential thermal analysis. The coordinates of ternary eutectics were determined: E ₁: 612°C, 16 mol % NaBO₂, 42 mol % NaCl, and 42 mol % Na₂CO₃; E ₂: 568°C, 12 mol % NaBO₂, 28 mol % Na₂CO₃, and 60 mol % Na₂MoO₄; E ₃: 575°C, 12 mol % NaBO₂, 32 mol % Na₂CO₃, and 56 mol % Na₂WO₄; E ₄: 628°C, 8 mol % NaBO₂, 20 mol % NaCl, and 72 mol % Na₂WO₄; and E ₅: 655°C, 9 mol % NaBO₂, 53 mol % NaCl, and 38 mol % Na₂WO₄.     

Li2SO4-Na2SO4-H2O和Li2SO4- K2SO4-H2O溶液的体积性质

本文用高精度数字式振荡管密度计测定了288K至318K温度范围内Li₂SO₄ + Na₂SO₄ + H₂O和 Li₂SO₄ + K₂SO₄ + H₂O三元体系的密度。混合溶液的离子强度范围从0.1到4.5 mol.kg_–1,混合溶液中Na₂SO₄和K₂SO₄的离子强度分数为0.2,0.4,0.6和0.8。用密度实验值拟合得到了不同温度下Pitzer离子相互作用模型混合参数θ_V和 ψ_V,模型的计算值与实验值的偏差在±0.002 g.cm_–3以内。用Pitzer模型计算了不同离子强度下三元体系的混合体积。     

SnSbBiS4-SnS and SnSbBiS4-Sn2Sb6S11 sections of the SnS-Sb2S3-Bi2S3 ternary system

SnSbBiS₄-SnS and SnSbBiS₄-Sn₂Sb₆S₁₁ sections were studied by physicochemical methods (DTA, X-ray powder diffraction, microstructure observation, and microhardness measurements). These sections were found to be eutectic quasi-binary sections of the SnS-Sb₂S₃-Bi₂S₃ ternary system. Solid solution regions based on the initial components were found on either side of the sections. Alloys in the solid solution region are p-type semiconductors.     

Theoretical study of polyoxide clusters B20O30, Al20O30, V20O50, Si20O30H20, and Si20O30F20

The structural, electronic, and vibrational characteristics and energies of the isolated polyoxide clusters B₂₀O₃₀, Al₂₀O₃₀, V₂₀O₅₀, Si₂₀O₃₀H₂₀, and Si₂₀O₃₀F₂₀ and their complexes with the H⁻ ion and ammonia complexes Al₂₀O₃₀ · nNH₃ have been calculated by the density functional theory B3LYP method with different basis sets. The computation results show that the symmetric closo structure I _h with oxygen bridges located above the centers of the faces of an empty [M₂₀] dodecahedron is more favorable for V₂₀O₅₀, Si₂₀O₃₀H₂₀, and Si₂₀O₃₀F₂₀. For B₂₀O₃₀, the cage closo isomer is also more favorable than the other isomers, but its structure is severely distorted as compared to a dodecahedron and has a symmetry close to C ₃ . For Al₂₀O₃₀, the I _h structure corresponds to a high-lying local minimum of the potential energy surface. For Al₂₀O₃₀, a set of unusual puckshaped isomers of symmetry C _i , with different numbers of four-coordinate atoms ^IVAl and three-coordinate atoms ^IIIO, was localized; these structures are more than 90 kcal/mol more favorable than the dodecahedron I _h . The most favorable isomer of Al₂₀O₃₀ contains twelve four-coordinate atoms ^IVAl and four five-coordinate atoms ^VAl. The energies of dissociation of the most favorable M₂₀O₃₀ clusters into the M₂O₃ (C _2v ) and M₄O₆ (T _d ) fragments and, in the case of Al₂₀O₃₀, also into the Al₈O₁₂ (O _h ) and Al₁₂O₁₈ (D _3d ) fragments, have been estimated. The conclusion has been drawn that these clusters can, in principle, exist and can be experimentally detected in the isolated state. Analogous calculations have been performed for ammonia complexes Al₂₀O₃₀ · nNH₃ with n varying from 1 to 20. The effect of solvation on the relative stability of the dodecahedral and puckshaped isomers of the Al₂₀O₃₀ cluster is observed. The isomers with ammonia molecules in their first coordination sphere become much closer to one another on the energy scale; however, the dodecahedron remains a considerably less favorable intermediate. Original Russian Text ? O.P. Charkin, N.M. Klimenko, D.O. Charkin, 2008, published in Zhurnal Neorganicheskoi Khimii, 2008, Vol. 53, No. 4, pp. 624–635.     

Extension of the La7Mo7O30 structural type with La7Nb3W4O30 and La7Ta3W4O30 compounds

Two compounds of formula La₇A₃W₄O₃₀ (with A=Nb and Ta) were prepared by solid-state reaction at 1450 and 1490 °C. They crystallize in the rhombohedric space group R-3 (No. 148), with the hexagonal parameters: , and , . The structure of the materials was analyzed from X-ray, neutron and electronic diffraction. These oxides are isostructural of the reduced molybdenum compound La₇Mo₇O₃₀, which are formed of perovskite rod along [111]. An order between (Nb, Ta) and W is observed.     

Structural chemistry of Sr3Cr2WO9, Ca3Cr2WO9, and Ba3Cr2WO9

We have studied the preparation and crystallographic structure of three perovskite-type compounds: Sr₃Cr₂WO₉, cubic, the lattice parameter of which is a = 7.812Å; Ca₃Cr₂WO₉, tetragonal, the lattice parameters of which are a = 5.408 Å and c = 7.635Å; and Ba₃Cr₂WO₉, hexagonal, the lattice parameters of which are a = 5.691 Å and c = 13.957Å. We have compared these three structures and shown the relationship between the dimensions of the alkaline-earth metal and the existence of the different structures.