The Surface Imprinted Polystyrene Beads Prepared via Emulsion Templates

In this paper, the surface imprinted cross-linked polystyrene beads were prepared via suspension polymerization with styrene (St), divinylbezene (DVB), polyvinyl alcohol (PVA1788),the mixture of Span 85 and xylene or the mixture of Span 85 and paraffin as monomer,cross-linking agent, dispersion stabilizer and templates, respectively. The results indicate that there are dense cavities on the surface of beads, and the diameter and density of cavity are related with the composition and amount of emulsion template. The forming mechanism of cavity from thermodynamics and dynamics was proposed.     

Irradiation Initiated Grafting of Poly（butyl acrylate） onto Nano-sized Calcium Carbonate Particles

The present work reports the irradiation induced grafting polymerization onto nano-sized CaCO3 particles, mainly focusing on the effects of pretreatment with silane coupling agent. It is proved that poly(butyl acrylate) can be grafted onto the nanoparticles using the technical route suggested by the authors, and the silane treatment of the nanoparticles promotes the grafting polymerization.     

Dispersion stability and rheological behavior of suspensions of polystyrene coated fumed silica particles in polystyrene solutions

Polystyrene coated silica（SiO₂@PS） core-shell composite particles with averaged diameter of about 290 nm were prepared by in situ emulsion polymerization of styrene on the surface ofγ-methacryloxypropyltrimethoxysilane grafted SiO₂ nanoparticles of 20-50 nm in diameter.Rheological behavior and dispersion stability of SiO₂@PS suspension in 10 wt%PS solution were compared with suspensions of untreated SiO₂ and silane modified SiO₂ nanoparticles.Suspensions of the untreated and the silane modified SiO₂ exhibited obvious shear thinning.The SiO-2@PS suspension exhibits shear viscosity considerably smaller than suspensions of untreated and silane modified SiO₂ at low shear rates.Transmission electron microscopy showed that the composite particles can uniformly and stably disperse in PS solution compared to other suspensions,implying that the PS shell can effectively enhance the particle compatibility with PS macromolecules in solution.     

EFFECTS OF COUPLING AGENTS ON THE CRYSTALLIZATION BEHAVIOR OF PP/T-ZnOw COMPOSITES

The objectives of this paper are to understand the crystallization behavior of polypropylene(PP)composites with surface modified tetra-needle-shaped zinc oxide whisker(T-ZnOw).T-ZnOw was surface modified with different coupling agents,such as silane coupling agents(KH-550,KH-560)and titanate coupling agent(NDZ-105),in order to improve the compatibility between PP and T-ZnOw.DSC and POM were used to characterize the melt and crystallization behavior and the crystalline structures of the composites,respectively.The results show that the surface modified T-ZnOw acts as a nucleating agent of PP crystallization,depending on the coupling agent used for modification.KH-550 and KH-560 have more apparent role in improving the interfacial interaction than NDZ-105 and induce PP crystallization at higher temperature and with smaller spherulites size.The results also suggest that the crystallization behavior depends on not only the content of coupling agent,but also the content of the surface modified T-ZnOw used in the composites.     

Preparation, Curing Reactivity and Thermal Properties of Titanium-doped Silicone Resins

Novel titanium-doped silicone resins were synthesized from low-cost silane monomers and tetrabutyl titanate as raw materials and hydrochloric acid as catalyst, with titanium element as dopant into principal chain of Si-O-Si. The resins were characterized by means of FTIR, 1 H NMR and 13 C NMR spectra, their thermal properties and curing properties were investigated and their corresponding films were determined. The results show that the thermal stability and storage stability of the resins were influenced by the types of silane monomers containing different carbon atomicities of organic group. The thermal stability of the titanium-doped silicone resin with a molar ratio of silane monomer B(n-propyl triethoxysilane) to silane monomer C(n-octyl triethoxysilane) being 1:1 is superior to that of the resin with a molar ratio of silane monomer B to silane monomer C being 1:3. However, the storage stability of the former is inferior to that of the latter.This work also showed that the synthesized titanium-doped silicone resins have the highest thermal stability up to 450―500 °C with an atomicity molar ratio of 1:4 of titanium to silicon in the reactants. But the best storage stability of the resin prepared from the reactants with an atomicity molar ratio of 1:6[n(Ti):n(Si)] was obtained. The effect of the type and content of curing agent on the curing properties of the resin was also studied. Moreover, thermal mechanism and curing mechanism were proposed in this work.     

EFFECT OF SILANE COUPLING AGENT ON THE MECHANICAL, THERMAL PROPERTIES AND MORPHOLOGY OF TREMOLITE/PA1010 COMPOSITES

Tremolite,a kind of inorganic filler,was modified with a silane coupling agentγ-methacryloxypropyl trimethoxy silane (MPS) in ethanol/ammonia solution.The graft of MPS on tremolite was confirmed by X-ray photoelectron spectroscopy (XPS),IR and thermogramitric analysis (TGA) measurements.In addition,contact angle analysis showed that particle surface property was changed from hydrophilicity to hydrophobicity after the modification.Modified tremolite and pure tremolite were blended respectively with PA1010...     

Thermosensitive Particles with Unusual Morphology Prepared by Dispersion Copolymerization

The monodispersed polymeric particles with an unusual structure were prepared by the dispersion copolymerization of acrylonitrile/styrene（AN/St） in mixed solvents of ethanol/water by using the poly（N-isopropylacrylamide） （PNIPAAm） macromonomer as a reaction stabilizer. It was found that the AN monomer plays a key role in the formation of the particles with special morphology analyzed via scanning electron microscopy （SEM）. The reaction parameters have remarkable influences on the particle size and morphology. The particles possess a thermosensitive property according to the result of laser light scattering（LLS）.     

Synthesis of Ag-SiO2 composite nanospheres and their catalytic activity

A simple,mild,and time-saving method is employed to synthesize Ag-SiO2 composite nanospheres with Ag nanoparticles uniformly distributed on the surface of SiO2 nanoparticles.The chemical elements and the morphology of Ag-SiO2 composite nanospheres were analyzed with transmission electron microscopy(TEM),X-ray power diffraction(XRD),and X-ray photoelectron spectroscopy(XPS).On the surface of Ag-SiO2 composite nanospheres,silane coupling agent(KH-550)is introduced as an intermediary to connect the surfaces of SiO2 nanospheres and Ag nanoparticles,which is also helpful for avoiding the aggregation of Ag nanoparticles.It is found that Ag-SiO2 composite nanospheres have very good catalytic properties for the reduction of organic dyes,which may have potential application in wastewater treatment.     

MORPHOLOGY EVOLUTION OF POLY（St-co-BuA）/SILICA NANOCOMPOSITE PARTICLES SYNTHESIZED BY EMULSION POLYMERIZATION

Poly（St-co-BuA）/silica nanocomposite latexes were synthesized via conventional emulsion polymerization in the presence of 3-（trimethoxysilyl）propyl methacrylate modified colloidal nano-silica. The effects of surface property, particle size and content of colloidal nano-silica as well as the concentrations of monomer and surfactant on the morphology of nanocomposite latex particles were investigated by transmission electron microscope （TEM） and scanning electron microscope （SEM） in detail. Various interesting morphologies such as grape-like, Chinese gooseberry-like, pomegranate-like and normal core-shell structures were observed. Droplet nucleation mechanism competing with micelle nucleation mechanism was proposed to explain the morphological evolution of the nanocomposite particles.     

Preparation and evaluation of Fe3O4-core@Ag-shell nanoeggs for the development of fingerprints

The surface of individual, relatively dispersed Fe3O4 nanospheres is coated with a thiol-terminated silane, then the thiol on the Fe3O4 particles’ surfaces treats with nano-Ag colloidal solution to form Ag-modified Fe3O4 nanoparticles. Eventually, a solid shell of Ag is capped onto the Ag-modified Fe3O4 nanoparticles by reducing aliquots of AgNO3 solution using NaBH4 as a reducing agent. The as-prepared Fe3O4 -core@Ag-shell nanoeggs, which are uniform in size, highly monodisperse, stable against aggregation and have high magnetization, were depended on thin shell of the attached nano-Ag, the size of Fe3O4 nanoparticles, the volume of thiol-terminated silane as well as the ultrasonication. The Fe3O4 -core@Ag-shell nanoeggs are proposed to detect fingermarks on different surface, with which the fingermarks can be viewed directly, due to the clear ridge detail.     

Synthesis of hematite/silica/polymer composite colloids with a tunable morphology

Hematite/SiO₂/polystyrene colloidal particles were synthesized through emulsion polymerization, in the presence of seeds coated with 3-methacryloxypropyltrimethoxysilane (MPS). Scanning and transmission electron microscopy studies indicate that flying saucer-like particles can be prepared by taking advantage of the coalescence phenomenon which occurs between growing polymer nodules when the MPS surface density of the coupling agent is high. By decreasing this density, multipod-like and raspberry-like composite particles were obtained, depending on the concentration of monomer.     

二氧化硅/聚苯乙烯单分散性核/壳复合球的制备

采用无皂乳液聚合包覆 ,制备了二氧化硅 聚苯乙烯单分散核 壳 (SiO2 PS)复合颗粒 ,包覆层厚度达到 10 0nm .选择 80～ 2 5 0nm二氧化硅粒径作为核颗粒 .为提高包覆效率 ,二氧化硅颗粒先用偶联剂甲基丙烯酰 (3 三甲氧基硅烷 )丙酯 (MPS)进行不同程度的表面改性 .控制MPS的结合率和单体的初始浓度可提高包覆效率 ,同时得到了单分散性复合颗粒 ,用透射电镜 (TEM)观察复合粒子的核 壳形态 .用动态光散射法 (DLS)测量表明所得复合颗粒具有单分散性 .     

Preparation of Al(OH)3/PMMA nanocomposites by emulsion polymerization

Al(OH)₃/PMMA nanocomposites were prepared by the emulsion polymerization of methyl methacrylate (MMA) in the presence of surface‐functionalized Al(OH)₃ particles. Nanosized Al(OH)₃ particles were previously functionalized with a silane coupling agent, 3‐(trimethoxysilyl) propyl methacrylate (γ‐MPS), which was confirmed by FT‐IR and XRF analysis. The average size of seed particles was around 70 nm, and the density of the coupling agent on the particles was calculated to be 8.9 µmol m^?2. The emulsion polymerization was attempted at relatively high solid content of 40–46 wt%. The ratio of the seed particles to MMA had a strong influence on the stability of latex as well as the morphology of composites. Nanocomposites where several PMMA nodules were attached on the surface of Al(OH)₃ core were produced with stable latex emulsion when the weight percents of Al(OH)₃ to MMA were below 20. In the case of higher ratio of 30%, however, the latexes became unstable with an aggregation, and the product morphology was in the shape of large composite. Thermogravimetric analysis showed an improved thermal stability of PMMA composites with the incorporation of Al(OH)₃ nanoparticles. Copyright © 2008 John Wiley & Sons, Ltd.     

高分散性SiO2/PMMA复合材料的制备与表征——纳米SiO2在MMA中的分散

用硅烷偶联剂3-(甲基丙烯酰氧)丙基三甲氧基硅烷(MPS)对分散于乙醇中的纳米SiO2进行偶联改性,再通过介质置换和原位本体聚合制得SiO2/甲基丙烯酸甲酯(MMA)单体分散液和SiO2/PMMA复合材料.红外光谱分析(FTIR)和热重分析(TG)结合洗提实验考察了SiO2表面MPS的偶联率和偶联效率,透射电镜(TEM...     

Preparation of hemispherical hollow silica microcapsules with different affinity surface by using spherical vaterite calcium carbonate as template

We developed a method to prepare hemispherical hollow silica microcapsules (HHSM) with different affinity surfaces using spherical vaterite calcium carbonate (SVCC) as a template. The preparation process composed of the adhesion of calcium carbonate onto the surface of methyl methacrylate (MMA) droplets followed by suspension polymerization, the partial etching of calcium carbonate on the polymethyl methacrylate (PMMA) mother particle, the formation of silicon dioxide powder by sol–gel reaction and their deposition onto the etched flat surface of calcium carbonate, the surface modification of deposited silicon dioxide with silane coupling agent, the removal of the mother particle with acetone, the formation of silicon dioxide powder by sol–gel reaction and deposition onto the exposed hemispherical surface of calcium carbonate, and the surface modification of deposited silicon dioxide with silane coupling agent. The synthesized microcapsules had a complete hemispherical structure and both hydrophilic and hydrophobic surfaces. Copyright © 2007 John Wiley & Sons, Ltd.     

Acrylic polymer/silica organic–inorganic hybrid emulsions for coating materials: Role of the silane coupling agent

Acrylic polymer/silica organic–inorganic hybrid emulsions were synthesized by a simple method, that is, a conventional emulsion polymerization and subsequent sol–gel process, to provide water‐based coating materials. The acrylic polymer emulsions contained a silane coupling agent monomer, such as methacryloxypropyltriethoxysilane, to form highly solvent‐resistant hybrid films. On the other hand, the hybrid films from the surface‐modified polymer emulsions, in which the silane coupling agent was located only on the surface of the polymer particles and the particle core was not crosslinked, did not exhibit high solvent resistance. A honeycomblike array structure, which was derived from the polymer particles (diameter ≈ 50 nm) and the silica domain, on the hybrid film surfaces was observed by atomic force microscopy. The crosslinked core part and silane coupling agent containing the shell part of the polymer particles played important roles in attaining high solvent resistance. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4736–4742, 2006     

Synthesis of a Au/silica/polymer trilayer composite and the corresponding hollow polymer microsphere with a movable Au core

Gold/silica/poly(N,N'-methylenebisacrylamide) (Au/SiO2/polyMBAAm) trilayer composite materials were prepared by distillation precipitation polymerization of N,N'-methylenebisacrylamide (MBAAm) in the presence of Au/SiO2 particles as seeds, in which the seeds were prepared by a combination of gold-complexing and silane coupling agent with a further modified St?ber method. The polymerization of MBAAm was performed in neat acetonitrile with 2,2'-azobisisobutyronitrile as an initiator to encapsulate the Au/SiO2 seeds driven by the hydrogen-bonding interaction between the hydroxyl group on the surface of the seeds and the amide unit of polyMBAAm without modification of the Au/SiO2 surface in the absence of any stabilizer or surfactant. Hollow polyMBAAm microspheres with movable Au cores were further developed by the selective removal of the middle silica layer with hydrofluoric acid. The resultant trilayer Au/SiO2/polyMBAAm composite and hollow polyMBAAm microspheres with movable Au cores were characterized by transmission electron microscopy. The diffusion of chemicals across the polyMBAAm shell was investigated by a catalytic reduction of 4-nitrophenol to 4-aminophenol in the presence of sodium borohydride as a reductant.     

Dispersion polymerization of methyl methacrylate in supercritical CO2 in the presence of non-fluorous random copolymers

A series of non-fluorous random copolymers, composed of 3-[tris(trimethylsilyloxy)silyl] propyl methacrylate and 2-dimethylaminoethyl methacrylate, poly(SiMA-co-DMAEMA) with different comonomer ratios were prepared and utilized as stabilizers for the free radical dispersion polymerization of methyl methacrylate (MMA) in supercritical carbon dioxide (scCO₂). It was demonstrated that the composition and concentration of the stabilizer have a dramatic effect on the morphology of resulting poly methyl methacrylate (PMMA) latex. When the copolymeric stabilizer poly(SiMA-co-DMAEMA) (71:29) was employed, free-flowing spherical PMMA particles were produced in high yield. As the concentration of stabilizer increases, the resulting size of colloidal particles decreases. In addition, the monomer concentration and initial pressure affected the particle diameter of PMMA.     

Polyaniline microsphere encapsulated by poly(methyl methacrylate) and investigation of its electrorheological properties

Microspheres consisting of a poly(methyl methacrylate) (PMMA) shell wrapping the conductive polyaniline (PANI) particle as a core were prepared by an in-situ suspension polymerization method and then adopted as an electrorheological (ER) material. The polymerization reaction and encapsulation were confirmed by Fourier transform infrared spectrum analysis. The rod-like PANI particles were synthesized via an emulsion polymerization protocol and observed by transmission electron microscopy. In addition, a spherical shape of encapsulated PANI/PMMA (core/shell) microspheres was observed by scanning electron microscopy. The thermal stability of PANI/PMMA particles was examined by use of thermogravimetric analysis. The PANI/PMMA particle-based suspension in silicone oil exhibited typical ER behavior. The conductivity of PANI/PMMA particles was much lower than that of the rod-like PANI.     

A Facile Synthesis of Cu NPs and Ag NPs Coated by PS with Core–Shell Structure by Precipitation Polymerization

Copper nanoparticles (Cu NPs ) coated with polystyrene (PS ) (Cu NPs @PS ) were prepared by precipitation polymerization. First, Cu NPs were prepared by chemical reduction using cupric acetate as precursor, sodium polyacrylate (PAANa ) as stabilizer, and hydrazine hydrate as reducing agent. Then Cu NPs were coated by precipitation polymerization using styrene as monomer, 3‐(trimethoxysilyl) propyl acrylate as co‐monomer, and 2, 2‐azobisisobutyronitrile (AIBN ) as initiator. Ultraviolet–visible (UV –vis) spectroscopy and transmission electron microscopy (TEM ) results showed that stable composite particles could be synthesized by precipitation polymerization. The amount of PAANa had a significant effect on the size of Cu NPs . The addition of more PAANa resulted in smaller Cu NPs . The spherical Cu NPs became nanowires when increasing the stirring rate from 350 to 700 rpm during precipitation polymerization. Ag NPs @PS with core–shell structure were also prepared by this method, which appears to be universal.