Anionic Polymerization and Copolymerization of Hydrocarbon Monomers Catalyzed by Organobarium Initiators

The barium salt of the dimeric dianion of 1,1-diphenylethylene (Ba-DPhE) initiates polymerization and copolymerization of monomers capable of anionic polymerization (butadiene, isoprene, styrene) in ethereal and hydrocarbon solvents. Ba-DPhE is more stereospecific in butadiene polymerization (up to 70% of cis-1, 4-units in hydrocarbon medium) than initiators based on other metals of Groups I and II. The relative reactivity of monomers in copolymerization processes in THF decreases in an order typical for anionic polymerization: styrene > butadiene > isoprene. The most interesting feature of organobarium initiators is their ability to form random butadiene-styrene copolymers with high cis-1,4-butadiene unit content when copolymerization proceeds in a hydrocarbon medium.

A new phenomenon in anionic polymerization, the dependence of diene units structure on copolymer composition, was observed. Thus an increase of styrene content in butadienestyrene copolymer leads to conversion of cis-1,4-butadiene units into trans-1,4-units (in benzene) or to conversion of 1,4-units to 1,2-units (in THF). Similarly, an increase of butadiene content in its copolymer with isoprene (in benzene) leads to conversion of cis-1,4-isoprene units into trans-1,4-units.

Spectrophotometric, conductometric, and viscometric methods were used to study organobarium active centers. Certain anomalies connected with the formation of specific aggregates due to coupling of bifunctional hydrocarbon chains with bivalent counterions were observed.     

Facile Synthesis of Polyhydroxylated Polybutadiene Derived from Hydroxyl-Terminated Polybutadiene via Thiol-Ene Click Reaction

Polyhydroxylated polybutadiene (PHPB) was synthesized via a thiol-ene click reaction between hydroxyl-terminated polybutadiene (HTPB) and 2-mercaptoethanol (ME) with 2,2’-azoisobutyronitrile (AIBN) as initiator. Effects of AIBN content, reaction time and temperature on the click reaction were investigated by determining hydroxyl value of the PHPB. The PHPB was characterized by FT-IR, ¹H-NMR, ¹³C-NMR and GPC. Relative reactivity of three types of C?C double bonds (1,2-vinyl, 1,4-cis and 1,4-trans units) in the HTPB reacting with the ME was discussed. The results showed that the optimal reaction conditions were that the AIBN content, reaction time and temperature were 2.0 wt%, 180 min and 70°C, respectively. Under these conditions, the hydroxyl value of the PHPB was 3.12 mmol·g^?1 when the HTPB/ME mass ratio was 10:2. All three types of C?C double bonds in the HTPB could react with the ME and the reactivity order was: 1,2-vinyl unit > 1,4-cis unit > 1,4-trans unit.     

Microstructure of polyisoprene produced by cationic polymerization: NMR spectroscopic study

High-resolution ¹H and ¹³C NMR spectroscopy, including two-dimensional heteronuclear experiments, has been used to study the microstructure of polyisoprene produced by cationic polymerization. It is shown that macromolecules resulting from both regular and inverse additions are predominantly composed of trans-1,4-units, while 1,2- and 3,4-units are present in small amounts. NMR spectra demonstrate the absence of cis-1,4-units in the polymer, whereas broad signals (pedestals) are related to the presence of saturated structures. It is proposed to determine the content of trans-1,4-, 1,2-, and 3,4-units in cationic polyisoprene via the combined measurements of intensities of signals in the olefinic regions of ¹H and ¹³C NMR spectra.     

Structure of polypiperylene chain segments according to high-resolution 13C NMR spectra

The microstructure of stereoregular 1,4-trans-and 1,4-cis-polypiperylenes, as well as polymers prepared from the trans-and cis-piperylene isomers via cationic polymerization in the presence of TiCl₄, was studied by high-resolution ¹³C NMR spectroscopy. Polypiperylene synthesized through the cationic polymerization of the cis isomer had a more diversified morphology of the macromolecular chain, i.e., had higher relative amounts of 1,2-cis-units and combinations of irregular-addition 1,4-trans-units. It was shown that ¹³C NMR spectra give the most comprehensive and independent information on the details of structure of the piperylene macromolecular chain.     

Molecular structure of polybutadienes synthesized with a lithium-containing initiation system

With the use of high-resolution NMR spectroscopy (600 MHz) and gel-permeation chromatography, the products of anionic polymerization of butadiene initiated by n-butyllithium modified with sodium and magnesium alcoholates are studied. It is shown that a change in synthesis conditions makes it possible to vary the configuration and isomeric composition and molecular parameters of polybutadienes. The distribution of 1,2-, cis-1,4-, and trans-1,4-units in a chain has a pronounced statistical character and depends on the composition of the initiation system.     

丁苯、丁腈基聚氨酯的形态与性能

用示差扫描量热法 (DSC)、红外分光光度计 (FTIR)和原子力显微镜 (AFM)研究了端羟基聚丁二烯 苯乙烯共聚物 (HTBS)、端羟基聚丁二烯 丙烯腈共聚物 (HTBN)和端羟基聚丁二烯 (HTPB)与甲苯二异氰酸酯、1 ,4 丁二醇构成的溶液法聚二烯烃基聚氨酯 (PU)的形态结构 .结果表明HTPB和HTBS基PU的相分离程度很大 ,而HTBN基PU的相分离程度小 .这可能归因于HTBS软段的极性低 ,不能与硬段形成氢键 ,而HTBN软段中的腈基具有很强的极性 ,且可以与硬段形成氢键作用 ,增加了软硬段间的相容性 ,相分离程度明显降低 .AFM表明HTBN PU随着硬段含量提高 ,表面粗糙度增大 ,由软段为连续相逐渐过渡到双连续结构 .在硬段含量 6 3%时 ,HTBN和HTPB基PU均呈双连续结构 ,而HTBS PU中硬段为连续相 .HTBN PU软段的相区尺寸在1 2nm左右 ,表面粗糙度较大 ,HPBS PU软段的相区尺寸在 1 1nm左右 ,表面粗糙度最小 ,HTPB PU存在 1 4nm和 5 0nm大小不等的软段相区尺寸 .力学性能表明 ,在软段中引入苯乙烯和丙烯腈结构 ,可使聚氨酯抗张强度分别提高 1 5和 2倍 ,模量和断裂伸长率也明显提高     

高1, 4-结构端羟基聚异戊二烯遥爪聚合物的合成

本文采用保护基团引发剂法在环己烷溶剂中通过阴离子聚合合成双端羟基聚异戊二烯,并通过GPC、IR、1H NMR、羟值分析方法对其进行了表征。结果表明,聚合物有高的1,4-结构含量,同时聚合物的分子量大小可以控制、分子量分布窄、官能度接近2。     

Nature of active centers and stereospecificity of tetravalent titanium benzyl derivatives in polymerization of butadiene

Stereospecificity of tetrabenzyltitanium and its halogeno-derivatives in the polymerization of butadiene has been investigated. The content of 1,2-units decreases while the content of 1,4-cis-units increases in the resulting polybutadiene for the series (C₆H₅CH₂)₄Ti, (C₆H₅CH₂)₃TiCl, (C₆H₅CH₂)₃TiBr, (C₆H₅CH₂)₃Til. Tribenzyltitanium iodide exhibits high stereospecificity for the formation of 1,4-cis-units and their content reaches 94–97%. By determining the number of benzyl groups linked with titanium at different degrees of conversion, it has been shown that the active centre formed from tetrabenzyltitanium contains three benzyl groups and one polymer chain. Two benzyl groups, one iodine atom and one polymer chain are attached to a titanium atom in the active centre for the case of tribenzyltitanium iodide. Electron donors sharply change the stereospecificity of tribenzyltitanium iodide: the content of 1,2-units in the polymer rises to 68%.     

Influence of Polar Modifiers on Microstructure of Polybutadiene Obtained by Anionic Polymerization. Part 2: Lewis Base (σ) Amine-Ether and Ether-Type Polar Modifiers

The influence of Lewis base (σ complex) amine-ether and ether-type polar modifiers on the microstructure of polybutadiene obtained by anionic polymerization was studied. Analysis of FT-IR-ATR, ¹H, and ¹³C NMR spectral data for polybutadienes obtained in the presence of the complexing agents showed that increase of concentration of all tested polar modifiers very strongly promoted formation of 1,2 butadiene isomeric structures, especially increasing the content of vinyl–vinyl and vinyl–trans-1,4 diads.     

Polymerization of butadiene catalyzed by a cobalt-containing catalyst in aliphatic media

The polymerization of butadiene catalyzed by the preformed Co(2-ethylhexanoate)₂-Et₃Al₂Cl₃-isoprene (a molar ratio of 1: 20: 20) catalytic system in toluene, cyclohexane, and hexane has been studied. In toluene, the catalyst demonstrates high activity and stereospecificity and yields a high-molecular-mass polymer. In cyclohexane and hexane, the catalyst has a high activity but affords polymers with lower contents of 1,4-cis-units and reduced intrinsic viscosities. The addition of EtAlCl₂ and/or a decrease in the polymerization temperature make it possible to obtain polybutadiene containing more than 96% 1,4-cis-units and an acceptable intrinsic viscosity (2.0–2.8 dl/g) in the nonaromatic solvents as well.     

Influence of polar modifiers on microstructure of polybutadiene obtained by anionic polymerization. Part 4: Acid-base polar modifiers forming σ-μ complexes: Amine-alkoxide,amine-ether-alkoxide,and ether-alkoxide

The influence of acid-base polar modifiers (σ-μ complex): amine-alkoxide, amine-ether-alkoxide, and ether-alkoxide complexes on microstructure of polybutadiene obtained by anionic polymerization was studied. The content of butadiene isomeric structures was determined based on FT-IR-ATR, ¹H, and ¹³C NMR data analyses. The results obtained indicated a very similar influence of all types of polar modifiers forming σ-μ complex on polymer microstructure leading to high vinyl polybutadiene with nearly equal ratios of cis-1,4 and trans-1,4 butadiene isomeric structures.     

正电子湮没谱研究聚烯烃聚氨酯的自由体积、微观结构和溶剂的扩散行为

用正电子湮没技术(PAS)结合示差扫描量热法(DSC)研究了聚烯烃聚氨酯的自由体积特征和微相分离结构的关系.结果表明,硬段含量增加,自由体积孔洞平均半径和自由体积分数减小;丁腈聚氨酯相分离程度小,相应自由体积孔洞平均半径和自由体积分数小,而丁羟聚氨酯的情况正好相反.石英弹簧法对苯和乙醇蒸气的溶解和扩散行为的研究表明,聚烯烃聚氨酯的自由体积孔洞平均半径和自由体积分数与苯和乙醇溶剂蒸气的无限稀释扩散系数呈正相关,但它们的无限稀释扩散系数和自由体积分数关系无法用Fujita的自由体积模型描述,可能归因于它们对聚烯烃聚氨酯复杂的溶胀行为.     

Synthesis of Hydroxy-Functional PMMA Macromonomers by Anionic Polymerization

Living anionic polymerization has been utilized to synthesize hydroxy end-functionalized PMMA macromonomers with styryl or allyl functionalities as the polymerizable end-groups. Protected hydroxy-functionalized alkyl lithium initiators have been used to initiate anionic polymerization of MMA. Subsequently the living chains with protected hydroxyl function have been terminated using 4-vinylbenzyl chloride (4-VBC) or allyl methacrylate (ALMA) to form α-hydroxy-ω-styryl and α-hydroxy-ω-allyl PMMA, respectively. These protected hydroxy-functionalized PMMA macromonomers have been characterized by GPC and ¹H-NMR. Termination using 4-VBC led to 50% functionalization, whereas that using allyl methacrylate led to 100% functionalization of the hydroxy-PMMA.     

Polymerization of butadiene with titanium-magnesium nanocatalysts

The suspension polymerization of butadiene in the presence of titanium-magnesium nanocatalysts combined with triisobutylaluminum is studied. The resulting polybutadiene is shown to contain up to 99% trans-1,4-units. The dependences of polymer microstructure on temperature and the Al-to-Ti ratio are investigated. The kinetic parameters of the process and the properties of trans-1,4-polybutadiene are examined.     

Filler-polymer interactions in filled polybutadiene compounds

Bound rubber in a filled rubber compound is formed by physical adsorption and chemisorption between the rubber and filler. Polybutadiene (PB) is composed of three components of 1,2-, cis-1,4-, and trans-1,4-units. Filler-polymer interactions in PB compounds filled with carbon black or silica were studied by analyzing microstructures of the bound rubbers with pyrolysis-gas chromatography. Differences in the filler-polymer interactions of the 1,2-, cis-1,4-, and trans-1,4-units were investigated. The filler-polymer interaction of the 1,2-unit is stronger than those of the cis-1,4- and trans-1,4-units. The interaction of the 1,2-unit with silica is stronger than with carbon black. Bound rubber content is decreased by treatment with ammonia. Change of the bound rubber composition after the ammonia treatment was also studied.     

Influence of polar modifiers on microstructure of polybutadiene obtained by anionic polymerization. Part 5: Comparison of µ, σ, σ+µ, and σ−µ complexes

A comparison was performed of the influence of polar modifiers forming (separately or simultaneously) σ and μ complexes with a living center during anionic polymerization of 1,3-butadiene — regarding the content and distribution of butadiene isomeric structures. Analysis of the ¹H NMR, ¹³C NMR, and FT-IR data indicated a significant discrepancy in terms of the determination of the polybutadiene microstructure depending on the analytical method applied. Nevertheless, it was observed that the application of polar modifiers forming different types of complexes with organometallic compounds provided the possibility to govern the content of 1,4- and 1,2-butadiene units in a very broad range (0.55 < cis/trans < 1.05 and 10% < vinyl < 90%, respectively) as well as to control diad distribution.     

A NEW PEAK (T_4) IN THE ~(13)C-NMR SPECTRUM OF POLYBUTADIENE

A new peak at 39.0 ppm in the ~(13)C-NMR spectrum of polybutadiene (PBD) was discovered. This peak is assigned to the fourth peak (T_4) of trans-1,4-sequence marked with an asterisk as shown in Fig. 3 in the text.The occurrence of T_4 carbon nuclei is strongly affected by their neighboring 1,2-units. So long as both contents of trans-1,4- and 1,2-units attain their proper amounts the peak (T_4) with appear in the ~(13)C-NMR spectrum of PBD.     

End‐capping of polystyrene by aliphatic primary amine by derivatization of precursor hydroxyl end group

A new and very efficient route for the synthesis of aliphatic primary amine terminated polystyrene (PS) is reported. In contrast to most known methods, only traditional commercially available reagents are used. PS is synthesized by anionic polymerization with a lithium counter ion and the living chains are end‐capped by a hydroxyl group upon addition of ethylene oxide followed by protonation. The ω‐hydroxyl end group is tosylated and the tosylate is then reacted with sodium azide. The azide terminal group is finally reduced into primary amine. The different steps of functionalization have been fully characterized by SEC, ToF‐SIMS, FTIR, and ¹H NMR. The amine content (= 98%) has been determined by acid‐base titration with perchloric acid. It clearly shows the efficiency of the synthetic method reported in this article although it is a multistep method. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1618–1629, 2000     

Anionic polymerization of lactones initiated by alkali graphitides. IV. Copolymerization of ε-caprolactone initiated by KC24

The copolymerization of ε-caprolactone (ε-CL) with octamethylcyclotetrasiloxane (D₄) and styrene (St) under the action of the second-stage potassium graphitide KC₂₄ was investigated. The copolymerizations were carried out in bulk or in xylene at 20°C. The content of the block copolymer ε-CL/D₄ in the polymerization mixture was 60–95%, the molecular weight ranging between 150,000 and 300,000. The data for the copolymers' composition obtained by ¹H-NMR and GPC showed 14–20% of D₄-units in the copolymer. The amount of the block copolymer ε-CL/St in the polymerization products was 0–87%, and the molecular weights in the case of copolymer formation were between 100,000 and 500,000. The content of St-units in the copolymers was from 10 to 75% as shown by GPC and ¹H-NMR. The mechanism of action of the initiator is discussed.     

Solvent effect in cis-1,4 polymerization of 1,3-butadiene by a catalyst based on neodymium

In this work a laboratory polymerization scale process was studied for the production of polybutadiene with high content of cis-1,4 repeating units. A Ziegler-Natta catalytic system based on neodymium versatate (catalyst), diisobutylaluminium hydride (cocatalyst) and tert-butyl chloride (chlorinating agent) was used. The influence of solvent nature (pure grade) and possible contaminants (electron donors) in a recovered solvent from a butadiene-styrene anionic polymerization industrial plant on the stereoselectivity and catalytic activity, molecular weight and molecular weight distribution of the resultant polybutadienes was studied. The polymers were characterized by infrared spectroscopy and size exclusion chromatography. Polybutadienes with cis-1,4 units content in the range of 99-98% were produced. The polymers weight-average molecular weight, , varied from 2.23 × 10⁵ to 4.47 × 10⁵ and the molecular weight distribution, MWD, from 3.1 to 5.1.