用晶格氧为氧源的甲烷部分氧化制合成气

 采用热重分析技术在甲烷气氛下考察了储氧材料Fe2O3提供晶格氧的过程，用甲烷／氧切换反应和在线质谱检测方法研究了以Fe2O3晶格氧代替气相氧用于甲烷部分氧化制合成气的可能性．结果表明，Fe2O3在甲烷气氛下的还原过程包括Fe2O3→Fe3O4和Fe3O4→FeO→Fe，甲烷被氧化为CO2和H2O．在750℃下进行的CH4／O2切换反应结果表明，首先，约25％的CH4与Fe2O3中的晶格氧反应，生成CO2和H2O，然后，生成的CO2和H2O与剩余的约75％的CH4在Ni／Al2O3催化剂上进行蒸汽重整和C\r\nO2重整，从而按燃烧－重整机理实现甲烷部分氧化制合成气．选择合适的CH4／O2切换条件，可使甲烷高转化率、高选择性地生成合成气．     

Fe203中的晶格氧用于甲烷在熔融盐中的催化燃烧(Ⅰ)催化剂的制备及性能表征

制备了新鲜的Fe2O3甲烷燃烧催化剂,利用XRD、SEM和TG等分析手段对催化剂的性能进行了表征.并在质量比为1:1的Na2CO3和K2CO3熔融盐中研究了Fe2O3中的晶格氧对甲烷的催化燃烧性能.TG分析表明,Fe2O3与CH4的反应分为两个阶段,第一个阶段从550℃开始,700℃结束,这一阶段里Fe2O3主要被还原成了Fe3O4,第二个阶段从800℃开始,Fe3O4被还原成了FeO和Fe;新生成的铁和低价铁氧化物与空气反应的TG曲线只出现一个增重阶段,从350℃开始质量开始显著增加,最后又重新生成了Fe2O3.在熔融碳酸盐体系进行的切换反应表明,在熔融盐中Fe2O3中的晶格氧能有效地对甲烷的燃烧过程进行催化,并且失去晶格氧的Fe2O3能与空气反应重新恢复其晶格氧,并且整个反应过程放出的热被储存在熔融盐热载体中,这更有利于甲烷的完全燃烧或部分氧化制合成气.因此,控制合适的反应条件,利用Fe2O3作为催化剂在熔融盐体系里使甲烷完全燃烧或部分氧化制合成气是可能的.     

晶格氧用于甲烷氧化制合成气的研究：—氧化铁的氧化还原性能

制备了氧化铁剂,对其进行了程序升温实验（O2－TPD、空气－TPO和CH4－TPR）和不同温度下的多次CH4－空气脉冲循环反应,并对催化剂进行了XRD表征,研究结果表明,Fe2O3不仅具有较高的稳定性,还具有良好的氧化还原性能,可使CH4氧化为CO2和H2O。在750－850℃范围内,Fe2O3具有良好的提供晶格氧的能力;在900℃以上,供氧速度减慢,供氧和补氧能力明显降低,XRD测试结果表明,高于900℃时,脉冲空气不能将与脉冲CH4反应后的氧化铁氧化为Fe2O3晶格,导致了氧化铁供氧量下降。     

Rh/SiO_2催化剂上甲烷部分氧化制合成气的反应机理

采用原位Raman光谱技术,在原料气中的O2未完全耗尽的条件下,对CH4部分氧化制合成气反应的Rh/SiO2催化剂床层前部贵金属物种的化学态以及由CH4解离所生成的碳物种进行了表征.在此基础上采用脉冲反应和同位素示踪技术,比较了CH4的部分氧化及其与H2O和CO2的重整等反应对催化剂床层氧化区内CO和H2生成的相对贡献,并将实验结果与Ra-man光谱表征结果进行了关联.结果表明,在600°C下将还原后的4%Rh/SiO2催化剂切入CH4:O2:Ar=2:1:45原料气,催化剂床层前部未检测到铑氧化物的Raman谱峰,但可清晰检测到源于CH4解离的碳物种;在700°C和接触时间小于1ms的条件下,催化剂床层的氧化区内已有大量CO和H2生成,在相同的实验条件下,CH4与H2O或CO2重整反应对氧化区内合成气生成的贡献则很小;以CH4:16O2:H218O:He=2:1:2:95为原料气的同位素示踪实验结果表明,在原料气中16O2未完全耗尽的情况下,反应产物中C16O的含量占CO生成总量的92.3%,表明CO主要来自CH4的部分氧化反应.上述结果均表明,在O2存在下Rh/SiO2催化剂上CO和H2可以通过CH4直接解离和部分氧化机理生成.     

BaCo0.7Fe0.2Nb0.1O3-δ膜反应器还原侧表面反应机理

研究了BaCo0.7Fe0.2Nb0.1O3-δ(BCFN)透氧膜反应器还原侧表面反应机理, 分析了表面催化微粒及催化床对膜反应器的作用. 提出了“催化解离机制”是构成甲烷重整BCFN膜反应器透氧量上升的主要原因; CH4, H2及CO在BCFN膜表面的反应活性依次为H2>CO>CH4; 当CH4气氛中加入H2或CO时, BCFN膜表面的主要发生由CH4直接氧化转变H2或CO的氧化反应, 同时极大提升了BCFN膜反应器的透氧量; BCFN膜表面氧化反应为“晶格氧”氧化反应模式主导.     

二甲醚的电催化氧化反应

 考察了负载于镓酸镧基电解质上的镍电极与镍－钐掺杂氧化铈复合电极电催化二甲醚氧化反应的特性．结果表明，反应的主要产物均为CO，H2和CH4，同时生成少量完全氧化的产物H2O和CO2．在开路电位下二甲醚发生裂解反应，生成的CO，H2和CH4三种主要产物的比例接近于1．在有电泵氧存在下，二甲醚的电催化氧化反应强烈地依赖于阳极及电解质材料的组成．Ni／La0．9Sr0．1Ga0．8Mg0．2O3界面上发生的主反应是二甲醚的部分氧化，且存在有严重的积碳现象．电极中掺入SDC（15％Sm3＋－掺杂的CeO2）后，二甲醚完全氧化性能明显增强；随着电流的增大，氢的生成速率显著减小，并生成大量的H2O．采用掺钴镓酸镧基电解质后，Ni－SDC主要表现为催化二甲醚部分氧化反应，且显著抑制了积碳的发生．Ni－SDC／La0．8Sr0．2Ga0．8－Mg0．11Co0．09O3上二甲醚电催化氧化反应的主要产物为1∶1的CO和H2．掺钴电解质引起Ni－SDC具有特殊的催化性能，可能与电解质中p型电导的存在有关．     

NOx催化的甲烷气相氧化反应

 考察了没有固体催化剂时NOx对甲烷气相氧化的催化作用，并用原位红外光谱研究了CH4－O2－NOx体系随温度的变化．实验结果表明，NOx对甲烷气相氧化有很高的催化活性．在20％CH4－10％O2体系中加入0．05％～0．2％的NO后，反应温度可降低200～300℃，在650～700℃下反应时，CH4转化率和CO选择性可分别达到38％和90％，产物中的n（H2）／n（CO）比为0．4～0．7．反应产物中可观察到有甲醛、甲醇和乙烯等，通过改变反应条件可以控制各组分的相对浓度．     

Ni/Al2O3催化剂表面状态对CH4氧化反应的影响

采用瞬变响应技术研究了常压700℃条件下气相O2、Ni/Al2O3催化剂表面上可逆吸附氧物种及催化剂的表面状态对CH4吸附、反应以及CH4部分氧化反应的影响,同时也对CH4部分氧化制合成气反应过程中催化剂表面所处的状态进行了研究.结果表明,如果催化剂表面处于氧化态,CH4不能吸附分解,只能通过RidealEley机理与催化剂表面的吸附氧进行非选择性氧化反应,这将严重影响CH4的转化和目的产物H2、CO的选择性.只有在还原的催化剂上,CH4部分氧化制合成气反应才能高转化、高选择性地进行.在CH4部分氧化制合成气反应过程中,催化剂表面处于还原态,不存在多余的中间氧物种NiO,但存在少量的碳物种,这有利于保持催化剂的还原态和抑制CO2的生成.     

流化床中 CH4/C3H8 自热重整制合成气

 在流化床反应器中, 考察了 Ni/SiO2 催化剂上 CH4 或 CH4-C3H8 临氧 CO2 重整 (自热重整) 制合成气反应性能. 结果表明, 在 CH4-C3H8 混合气自热重整反应中, Ni 粒径较小催化剂的活性和抗积炭性能较高, CH4 和 CO2 转化率分别达 75.5% 和 72.6%. C3H8 比 CH4 更易解离及被氧化, 部分 C3H8 解离出来的中间产物 CHx 物种可与吸附 H 结合为 CH4, 因而降低了 CH4 的表观转化率; CHx 也可与吸附的 CO2 物种反应生成 H2 与 CO, 从而促进了 CO2 的转化.     

甲烷催化部分氧化制合成气的反应机理

借助脉冲反应、质谱-程序升温表面反应（MS-TPSR）等技术研究了Ni／α-Al2O3催化剂上甲烷催化部分氧化制合成气（POM）的反应机理．结果表明,NiO上CH4不能解离产生H2只有当NiO被CH4还原为Ni0后,CH4才能解高产生H2,Ni0是CH4活化和POM反应的活性相;POM反应机理遵循直接氧化机理,CH4和O2均在Ni0上活化,活化过程形成的Ni…C和Niδ…Oδ物种是反应历程中的关键物种,Niδ …Oδ物种高选择性地与CH4解离产生的碳物种Ni…C反应生成CO．     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.     

Synthesis of substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles by intramolecular nitrilimine cycloaddition

Both substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles have been synthesized by the 3+2 intramolecular dipolar cycloaddition of nitrilimines to alkynes. This cyclization has been extended to more versatile 3-bromo derivatives by the use of alkynylbromides as dipolarophiles.     

Catalyst free,visible-light promoted photoaddition reactions between C60 and N-trimethylsilylmethyl-substituted tertiary amines for synthesis of aminomethyl-1,2-dihydrofullerenes

An efficient and benign method for the preparation of aminomethyl-substituted fullerenes has been developed. The process, involving catalyst free, visible-light irradiation of 10% EtOH-toluene solutions containing fullerene C₆₀ and N-trimethylsilylmethyl-substituted amines by using a 20 W compact fluorescent lamp, leads to formation of aminomethyl-substituted fullerene adducts in a highly efficient manner. The photoaddition reaction takes place via a pathway initiated by visible light absorption by C₆₀, followed by SET from the amine to the triplet excited state of C₆₀. Ethanol-promoted desilylation of the resulting a minimum radical then generates the corresponding α-amino radical which couples with the C₆₀ radical anion to form the anion precursor of the fullerene adducts. The new approach using visible-light takes place under mild conditions and it does not require the use of photocatalysts. Thus, the method developed in this effort could broadens the range of functionalized fullerene derivatives that can be readily prepared.     

Highly efficient and stereoselective cycloaddition of nitrones to indolyl- and pyrrolylacrylates

The reactions of various nitrones with indolyl- and pyrrolylacrylates proceeds regioselectively with high diastereoselectivity in the case of aldonitrones, and represents an effective method for obtaining new indolyl- and pyrrolyl-substituted isoxazolidine carboxylates stabilized by weak (CH?O) and moderate (NH?N) strength intramolecular hydrogen bonding. The resulting cycloadducts exhibit promising in vitro anti-influenza activities.     

Transition metal-free direct amination of benzoxazoles using formamides as nitrogen sources

A transition metal-free method for the direct amination of benzoxazoles using formamides as nitrogen sources is reported, which was mediated by an inexpensive and environmentally friendly tetrabutylammonium iodide/tert-butyl hydroperoxide system and gave the 2-aminobenzoxazole derivatives with moderate to good yields.     

l-Proline-catalyzed five-component domino reaction leading to multifunctionalized 1,2,3,4-tetrahydropyridines

Multifunctionalized 1,2,3,4-tetrahydropyridines are concisely synthesized in good yields via l-proline-catalyzed or l-proline/FeCl₃-cocatalyzed one-pot multicomponent reactions (MCRs). The MCRs involve a domino hydroamination/prins reaction/Mannich-type reaction/intramolecular dehydration-cyclization process. The molecular structure of 5baa, one of multifunctionalized 1,2,3,4-tetrahydropyridines, was confirmed by single-crystal X-ray diffraction.     

Studies of Photoionization of CF3 I by Femtosecond Time-resolved Mass Spectrometry

The multi-photon dissociative photoionization dynamics of CF3I has been studied with femtosecond two-color pump-probe time of flight mass spectra at a pump pulse of 265 nm and a probe pulse of 398 nm. The life constants of CF3I+ and its fragment ions CF3+ and I+ are obtained as (96±7), (198±130) and (167±6)fs, respectively. The multi-photon dynamics leading to these ions differ. CF3I+ corresponds to a (1+2′) transition with one-photon pump excitation to the A band of CF3I. CF3+ are mainly formed by a tow-photon probe excitation to the CF3+ with subsequent dissociation of parent ions. I+ are produced in (2+2′) combined with (1+1′+2′) process. The results provide information on the multi-photon pathways involved.