氨基功能化SBA-15的直接合成及其对CO_2的吸附性能研究

通过直接法合成了氨基功能化SBA-15介孔材料。使用X-射线粉末衍射法(XRD),N2吸-脱附,透射电子显微(TEM)等技术对氨基功能化材料进行了表征。实验结果表明:当反应原料中nAPTES/(nAPTES+nTEOS)≤0.20时,APTES功能化的材料都具有典型的介孔SBA-15结构;但当nAPTES/(nAPTES+nTEOS)≥0.225时,由于氨基对SBA-15结构的副作用导致SBA-15介孔结构坍塌。在氟离子辅助合成下可以获得高含量氨基(反应原料中nAPTES/(nAPTES+nTEOS)的比值为0.25)功能化的SBA-15材料,且此材料中的介孔孔径和BET比表面积都较大。CO2吸附结果表明,随着反应原料中APTES含量提高,所合成的材料对CO2的吸附量相应增加,同时在101kPa和25℃下,通过氟离子辅助合成的材料对CO2的吸附量远远优于无氟离子辅助合成材料的。本研究还对后嫁接法和直接合成法获得氨基功能化SBA-15介孔材料的优缺点进行了讨论。     

富含羧基的球形介孔分子筛SBA-15的合成及药物释放性能

原位合成了富含羧基的SBA-15球形介孔分子筛.研究了修饰剂三烷氧基氰乙基硅烷(CTES)的用量对介孔分子筛SBA-15形貌、孔径及BET比表面积的影响.用粉末X射线衍射(XRD)、扫描电子显微镜(SEM)、红外光谱(IR)和氮气吸附/脱附手段对样品进行了详细的表征.SBA-15分子筛展示了尺寸在0.5～1μm规则的球...     

氨基功能化SBA-15介孔分子筛的制备与表征

以3-氨丙基三乙氧基硅烷为偶联剂,采用后合成法对介孔分子筛(SBA-15)的表面进行改性,制得氨基功能化的介孔NH<,2>-SBA-15材料(简称NH<,2>-SBA-15),其结构和性能经FT-IR,元素分析,XRD,SEM及低温N<,2>吸附-脱附表征.结果表明,氨基成功地嫁接到SBA-15表面,含量高达3.47 ...     

介孔材料氨基表面修饰及其对CO2的吸附性能

采用接枝方法在介孔材料MCM-41和SBA-15的孔道内表面进行氨基化修饰, XRD、29Si-NMR、FT-IR、TGA、BET等测试结果表明, 氨丙基三乙氧基硅烷(APTS)和氨乙基氨丙基甲基二甲氧基硅烷(AEAPMDS)都分别接枝在介孔材料的孔道内, 表面氨基修饰量约为1.5-2.9 mmol·g-1. 表面修饰后介孔材料的孔道仍高度有序, 但比表面积减小. 表面修饰前后介孔材料对CO2的吸附性能发生显著变化, 由于物理吸附转化为以氨基为活性中心的化学吸附, 吸附量从修饰前的0.67 mmol·g-1提高到2.20 mmol·g-1.     

CeO_2/Ni/Mo/SBA-15甲烷二氧化碳重整催化剂的表征和催化性能(英文)

考察了CeO2修饰及未修饰的Ni/Mo/SBA-15催化剂在CH4-CO2重整上的催化性能并采用N2吸脱附、CO2程序升温脱附、H2程序升温还原、傅里叶红外光谱、X射线衍射、扫描电子显微镜和X射线光电子能谱对催化剂进行了表征.结果表明,在常压,800oC条件下,经过100h在线评价后,Ni/Mo/SBA-15和CeO2/Ni/Mo/SBA-15催化剂仍具有高的反应活性和规整的六方介孔结构,其中CeO2修饰的CeO2/Ni/Mo/SBA-15催化剂表面没有积炭形成,表明CeO2的加入促进了Ni物种在SBA-15介孔分子筛表面的分散,从而阻止了Ce/Ni/Mo/SBA-15催化剂上Ni的烧结和积炭.     

pH值响应性毒死蜱/铜席夫碱配合物改性SBA-15的制备及缓释性能

以3-氨丙基三乙氧基硅烷(APTES)、水杨醛和铜离子为改性剂,通过后嫁接法制得铜席夫碱配合物改性SBA-15(Cu-SBA-15),并以毒死蜱为模型药物,制备了毒死蜱/铜席夫碱配合物改性SBA-15缓释体系。利用TEM、SEM、XRD、N2吸附-脱附、TG、FTIR和XPS对SBA-15、氨基改性SBA-15(NH_2-SBA-15)、水杨醛希夫碱改性SBA-15(SA-SBA-15)的形貌、结构和Cu-SBA-15的配位情况进行了表征,考察了SBA-15在改性前后对毒死蜱的吸附量和缓释性能,并着重探究了毒死蜱/铜席夫碱配合物改性SBA-15载药体系在不同pH值下的释药行为。结果表明,APTES和水杨醛能够通过后嫁接法修饰于SBA-15,修饰后仍保持十分有序的孔道结构。SBA-15通过改性后,其对毒死蜱的吸附量由100 mg·g~(-1)增加至195 mg·g~(-1),且其对药物的缓释性能也得到改善。毒死蜱/铜席夫碱配合物改性SBA-15缓释体系显示出明显的pH值响应性,pH=3时的释药速率大于pH=11时,而在中性条件下的缓释效果相对最好。载药体系的释药行为可用Riger-Peppas动力学模型来描述,其药物释放由Fick扩散控制。     

高稳定性Ni/SBA-15催化剂的结构特征及其对二氧化碳重整甲烷反应的催化性能

 采用浸渍法制备了Ni含量为2.5%～20%的系列Ni/SBA-15催化剂,在常压连续流动固定床反应器上考察了催化剂对二氧化碳重整甲烷制合成气的催化性能,并用X射线衍射和N2吸附法研究了Ni/SBA-15催化剂的结构特征. 结果表明, Ni/SBA-15催化剂具有很高的CH4和CO2转化率, 12.5%Ni/SBA-15催化剂在800 ℃反应600 h后活性没有明显下降,但反应710 h后CH4的转化率下降了约50%, CO2的转化率下降了约25%. 其活性下降的主要原因是催化剂积炭. 在高温条件下反应时, SBA-15的介孔结构也没有遭到破坏,分子筛的孔壁能有效阻止活性组分Ni的团聚. SBA-15孔中组装一定量的Ni活性组分后,除了SBA-15的介孔外,还会形成另外一种较小的孔,但这不影响SBA-15的有序介孔结构,只是其孔径、孔容和BET比表面积降低.     

功能化离子液体修饰的SBA-15固定化Burkholderia cepacia脂肪酶

采用含不同碳链长度咪唑环的烷基功能化离子液体修饰介孔材料SBA-15,并通过X-射线衍射、元素分析、N2吸附-脱附、红外光谱和扫描电镜等方法研究了离子液体修饰对SBA-15结构的影响.以三乙酸甘油酯的水解为探针反应,考察了甲基、丁基、辛基等不同链长烷基取代咪唑类离子液体修饰的SBA-15固定化Burkholderia cepacia脂肪酶(BCL)的酶活、最适反应条件及稳定性等酶学性质.结果表明,离子液体修饰后材料保持了原有的介孔结构,其固定化酶对温度及低pH的敏感度降低,比活力及稳定性均显著提高.其中甲基功能化离子液体修饰的SBA-15固定化酶的比活力最高,是原粉SBA-15固定化酶的2.4倍;辛基功能化离子液体修饰的SBA-15固定化酶的热稳定性、储存稳定性、重复使用性及有机溶剂耐受性最佳.     

pH值响应性毒死蜱/铜席夫碱配合物改性SBA-15的制备及缓释性能

以3-氨丙基三乙氧基硅烷（APTES）、水杨醛和铜离子为改性剂,通过后嫁接法制得铜席夫碱配合物改性SBA-15（Cu-SBA-15）,并以毒死蜱为模型药物,制备了毒死蜱/铜席夫碱配合物改性SBA-15缓释体系。利用TEM、SEM、XRD、N₂吸附-脱附、TG、FTIR和XPS对SBA-15、氨基改性SBA-15（NH₂-SBA-15）、水杨醛希夫碱改性SBA-15（SA-SBA-15）的形貌、结构和Cu-SBA-15的配位情况进行了表征,考察了SBA-15在改性前后对毒死蜱的吸附量和缓释性能,并着重探究了毒死蜱/铜席夫碱配合物改性SBA-15载药体系在不同pH值下的释药行为。结果表明,APTES和水杨醛能够通过后嫁接法修饰于SBA-15,修饰后仍保持十分有序的孔道结构。SBA-15通过改性后,其对毒死蜱的吸附量由100 mg·g^-1增加至195 mg·g^-1,且其对药物的缓释性能也得到改善。毒死蜱/铜席夫碱配合物改性SBA-15缓释体系显示出明显的pH值响应性,pH=3时的释药速率大于pH=11时,而在中性条件下的缓释效果相对最好。载药体系的释药行为可用Riger-Peppas动力学模型来描述,其药物释放由Fick扩散控制。     

CuO/SBA-15催化剂上巴豆醛选择性加氢

通过γ-氨丙基三甲氧基硅烷(APTS)偶联与Cu2 离子络合两步法将CuO负载到介孔分子筛SBA-15上,制得CuO/SBA-15催化剂,考察了催化剂的巴豆醛选择性加氢反应性能.通过X射线粉末衍射、氮气吸脱附和程序升温还原(TPR)技术对催化剂进行了表征.结果表明,SBA-15分子筛负载CuO后保持原有的介孔结构,但是孔容和比面表积随着CuO负载量的增大而下降.TPR结果表明CuO/SBA-15系列催化剂有三种CuO物种:高分散CuO、晶相CuO和进入SBA-15分子筛骨架的Cu2 .高分散CuO物种对巴豆醛加氢反应的催化活性最高,晶相CuO物种次之,而进入SBA-15分子筛骨架的Cu2 物种几乎没有活性.     

Effect of amine functionalization of spherical MCM-41 and SBA-15 on controlled drug release

MCM-41 and SBA-15 silica materials with spherical morphology and different particle sizes were synthesized and modified by post-synthesis method with 3-aminopropyltriethoxysilane (APTES). A comparative study of the adsorption and release of a model drug, ibuprofen, were carried out. The modified and drug loaded mesoporous materials were characterized by XRD, TEM, N₂ physisorption, thermal analysis, elemental analysis and FT-IR spectroscopy. Surface modification with amino groups resulted in high degree of ibuprofen loading and slow rate of release for MCM-41, whereas it was the opposite for SBA-15. The adsorbed drug content and the delivery rate can be predetermined by the choice of mesoporous material with the appropriate structural characteristics and surface functionality.     

有机胺修饰具有较大孔径介孔材料的二氧化碳吸附性能

以非离子表面活性剂P123为模板剂,正硅酸甲酯为硅源,通过加入不同的扩孔剂制得具有较大孔径的SBA-15类介孔材料,并采用粉末X射线衍射(XRD)、低温氮气吸附-脱附、扫描电镜(SEM)、傅里叶变换红外(FTIR)光谱等手段对所得样品进行了表征.加入扩孔剂可以明显增大介孔材料的孔容和孔径,而异辛烷为扩孔剂的扩孔效果明显优于四氯化碳.经四乙烯五胺(TEPA)镀饰后,这些样品均表现出良好的CO2吸附性能.其中对于除去模板剂后再镀胺的样品,其CO2吸附能力与介孔材料孔道结构关系不大,而对于未除模板剂的原粉镀胺样品,CO2吸附能力则随孔道的变大而增强.此外,通过吸附等温线和CO2-程序升温脱附(TPD)手段比较了温度和压力对CO2吸附的影响,发现在较高温度下吸附时CO2的吸附能力随压力的变化存在显著差别,因而在这类TEPA修饰的介孔材料上可通过变压吸附的途径来实现对环境气流中CO2的吸附和分离.     

SBA－15的二氧化钛改性及其光催化降解对氯苯酚

在“后合成”法在介孔二氧化硅SBA－15的孔壁表面键接了二氧化钛,并对其 结构进行了表征。改性后的SBA－15保持了规则的介孔结构,并在孔壁表面形成了 类似于锐钛型二氧化钛的Ti-O-Ti网络结构。光催化降解对氯苯酚的结果表明,经 过两次二氧化钛键接的样品表现出较高的光催化效率。但是由于对酚、醌等中间产 物的强烈吸附以及孔道中反应物质的扩散速度慢,使得其光催化活性略低于纯的锐 钛型二氧化钛。     

Immobilization of human carbonic anhydrase on gold nanoparticles assembled onto amine/thiol-functionalized mesoporous SBA-15 for biomimetic sequestration of CO2

A biocatalyst was synthesized by immobilizing human carbonic anhydrase onto gold nanoparticles assembled over amine/thiol-functionalized mesoporous SBA-15. The physicochemical properties of the functionalized mesoporous SBA-15 were obtained by XRD, BET, FE SEM, HR TEM, EDS, and zeta potential analysis. The biocatalytic performance was studied for para-nitrophenyl acetate (p-NPA) hydrolysis. The kinetic parameters K(m) were found to be 22.35 and 27.75 mM, and K(cat)/K(m) values were 1514.09 and 1612.25 M(-1) s(-1) for HCA immobilized on gold nanoparticles assembled on amine/thiol-functionalized mesoporous SBA-15 (HCA/Au/APTES/SBA-15 and HCA/Au/MPTES/SBA-15), respectively. These HCA/Au/APTES/SBA-15 and HCA/Au/MPTES/SBA-15 were investigated for biocatalytic hydration of CO(2) and its precipitation as CaCO(3). The amount of CaCO(3) precipitated over HCA/Au/MPTES/SBA-15 was nearly the same as that precipitated over free HCA. Storage stability and reusability studies suggested that HCA/Au/MPTES/SBA-15 retained its activity even after 20 days storage at 25 °C and 20 recycling runs. The present results demonstrate that HCA/Au/MPTES/SBA-15 and HCA/Au/APTES/SBA-15 are highly efficient potential nanobiocatalysts for industrial-scale CO(2) sequestration.     

Primary, secondary, and tertiary amines for CO2 capture: designing for mesoporous CO2 adsorbents

CO(2) emissions, from fossil-fuel-burning power plants, the breathing, etc., influence the global worming on large scale and the man's work efficiency on small scale. The reversible capture of CO(2) is a prominent feature of CO(2) organic-inorganic hybrid adsorbent to sequester CO(2). Herein, (3-aminopropyl) trimethoxysilane (APTMS), [3-(methylamino)propyl] trimethoxysilane (MAPTMS), and [3-(diethylamino) propyl] trimethoxysilane (DEAPTMS) are immobilized on highly ordered mesoporous silicas (SBA-15) to catch CO(2) as primary, secondary, and tertiary aminosilica adsorbents. X-ray photoelectron spectroscopy was used to analyze the immobilized APTMS, MAPTMS, and DEAPTMS on the SBA-15. We report an interesting discovery that the CO(2) adsorption and desorption on the adsorbent depend on the amine type of the aminosilica adsorbent. The adsorbed CO(2) was easily desorbed from the adsorbent with the low energy consumption in the order of tertiary, secondary, and primary amino-adsorbents while the adsorption amount and the bonding-affinity increased in the reverse order. The effectiveness of amino-functionalized (1(o), 2(o), and 3(o) amines) SBA-15s as a CO(2) capturing agent was investigated in terms of adsorption capacity, adsorption-desorption kinetics, and thermodynamics. This work demonstrates apt amine types to catch CO(2) and regenerate the adsorbent, which may open new avenues to designing "CO(2) basket".     

Pb (II) removal from aqueous media by EDTA-modified mesoporous silica SBA-15

An organic-inorganic hybrid mesoporous silica material was synthesized by two-step post-grafting method of SBA-15 with 3-aminopropyltrimethoxy-silane (APTES) and thionyl dichloride (SOCl(2)) activated ethylenediaminetetraacetic acid (EDTA) in sequence and measured by means of Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), elemental analysis (EA), transmission electron microscopy (TEM), nitrogen (N(2)) adsorption-desorption analysis and back titration. The material was found having the beneficial properties of mesoporous silica SBA-15 and EDTA. Adsorption potential of the material for Pb (II) removal from aqueous solution was investigated by varying experimental conditions such as pH, contact time and initial metal concentration. The removal efficiency of Pb(2+) was high under studied experimental conditions. The adsorption equilibrium could be reached within 20min and the kinetic data were fitted well by pseudo-second-order and intraparticle diffusion model. The adsorbent exhibited a favorable performance and its maximum adsorption capacity calculated by the Langmuir model was 273.2mgg(-1). Recycling experiments showed the adsorbent could be regenerated by acid treatment without altering its properties. The chemical states of the elements involved in the adsorption were analyzed by X-ray photoelectron spectroscopy (XPS). The results demonstrated that the adsorption mechanism of the material involved Na Pb ion-exchange and carboxyl group dominated surface complexation.     

Direct synthesis and catalytic applications of ordered large pore aminopropyl-functionalized SBA-15 mesoporous materials

SBA-15 mesoporous silica has been functionalized with aminopropyl groups through a simple co-condensation approach of tetraethyl orthosilicate (TEOS) and (3-aminopropyl)triethoxysilane (APTES) using amphiphilic block copolymers under acidic conditions. The organic-modified SBA-15 materials have hexagonal crystallographic order, pore diameter up to 60 A, and the content of aminopropyl groups up to 2.3 mmol g(-1). The influences of TEOS prehydrolysis period and APTES concentration on the crystallographic order, pore size, surface area, and pore volume were examined. TEOS prehydrolysis prior to the addition of APTES was found essential to obtain well-ordered mesoporous materials with amino functionality. The amount of APTES incorporated in the silica framework increased with the APTES concentration in the synthesis gel, while the ordering of the mesoporous structure gradually decreased. Analysis with TG, IR, and solid state NMR spectra demonstrated that the aminopropyl groups incorporated in SBA-15 were not decomposed during the preparation procedure and the surfactant P123 was fully removed through ethanol extraction. The modified SBA-15 was an excellent base catalyst in Knoevenagel and Michael addition reactions.     

Mesoporous SBA-15 materials modified with PW or W active species as catalysts for the epoxidation of olefins with H<Subscript>2</Subscript>O<Subscript>2</Subscript>

Five catalysts containing PW or W active species that anchored onto aminosilylated mesoporous silica SBA-15 by a post-grafting route were prepared and the resulting PW or W/APTES/SBA-15 hybrid materials were characterized by XRD, N₂ adsorption/desorption, surface area analysis, TEM, FT-IR, and ICP (inductively coupled plasma atomic emission spectroscopy). The names of these catalysts have been abbreviated as SBA-15m-a, SBA-15m-b, SBA-15m-c, SBA-15m-d, and SBA-15m-e according to the different active species. The PW or W active species were highly dispersed in the channels of the modified mesoporous materials. The interaction between PW or W species and amino groups grafted on the channel surface of SBA-15 led to the immobilization of PW or W species. Their catalytic activity in the epoxidation of cyclooctene with H₂O₂ as oxidant was investigated. Among them, SBA-15m-a showed the best performance, with 98.9% conversion and 98.4% selectivity. The catalyst could be reused for six times with a little decrease in activity.     

Ordered mesoporous carbon as an efficient and reversible adsorbent for the adsorption of fullerenes

An ordered mesoporous carbon, CMK-3, was synthesized using a mesoporous siliceous material, SBA-15, as the template. CMK-3 was characterized and used for the adsorption of fullerenes C60 and C70. It was found that the adsorption capacity of CMK-3 is 4 times higher than that of activated carbon. The adsorption equilibrium isotherms of C60 and C70 on CMK-3 were studied for both single and binary systems. The reversibility of fullerene adsorption on CMK-3 was also explored. The results showed that CMK-3 is an effective and reversible adsorbent for the separation of fullerenes by adsorption.     

酸诱导介观相转变硅基介孔材料的合成机理及其改性

采用两步法以三嵌段共聚物P104(PEO27-PPO61-PEO27)为模板剂合成介孔材料, 研究了介孔材料结构随体系pH 值的变化, 探讨了体系中介观相转变的机理. 研究表明,随着pH 的升高, 发现体系中无机物种和模板剂所组成的介观相发生了转变,由P6mm 的SBA-15(pH=1.51-2.67)2D六角孔道结构转变为3D 蠕虫状孔道的MSU-X(pH=3.93-4.56)结构. 对所得的两种不同种类的硅基材料以γ-胺丙基三乙氧基硅烷(APTES: NH2(CH2)3Si(C2H5O)3)进行表面烷基化改性结果表明, 在同样的条件下, 经过改性后MSU-X类介孔材料孔壁上接枝的烷基数目要远超过SBA-15 类介孔材料.