工业Fe-Mn催化剂上基于详细反应机理的F-T合成动力学模型Ⅱ.不同校正方法的动力学模型分析

 通过平衡闪蒸模拟催化剂孔道液体组成、烯烃物理吸附和虚拟烯烃分压等方法,考察了化学反应以外的非本征因素对F-T合成动力学模型的校正. 平衡闪蒸模拟催化剂孔道中烯烃组成的校正计算结果表明,在烯烃浓度出现峰值前,溶解度效应对烯烃再吸附及参与二次反应起主导作用,而在烯烃浓度出现峰值后,烯烃的扩散和物理吸附等效应可能起主导作用. 分析烯烃添加的反应器模拟结果发现,考虑烯烃物理吸附作用的动力学模型校正方法不能够正确反映烯烃添加实验的定性规律,而虚拟烯烃分压校正方法能够正确反映烃分布规律并可定量预测烯烃添加对产物分布规律的影响,这对需要尾气循环的F-T合成工业操作具有重要意义.     

F-T合成校正综合动力学模型

考虑了烯烃、醇与酸的再吸附及其非本征效应(烯烃、醇与酸在催化剂孔道中的扩散作用、物理吸附及溶解度效应)对产物分布的影响,推导了基于详细反应机理的亚甲基插入的烷基机理F-T合成校正综合动力学模型.利用文献数据对动力学模型进行了回归,获得了与文献报道结果相一致的动力学参数.由校正动力学模型计算的烷烃、烯烃、醇与酸产物分布及烯烃比、醇烃比及酸烃比与实验数据较好地吻合.动力学计算结果表明,在铁锰催化剂上,烷烃、烯烃、醇与酸生成的反应是平行竞争反应,烯烃、醇与酸在催化剂表面的再吸附及二次反应导致产物分布偏离了ASF分布.动力学研究还表明,相同碳数的醇与酸产物在催化剂表面上再吸附及二次反应的机会比相同碳数的烯烃大.通过比较相同碳数的烯烃、醇与酸的分子体积及沸点,指出了在铁锰催化剂上,低碳数的烯烃、醇与酸的再吸附及二次反应对产物分布影响的非本征效应中,烯烃、醇与酸的扩散阻力不是主导效应.     

Co/ZrO2/SiO2催化剂费-托合成反应动力学研究Ⅱ. 动力学模型的构建和回归

 在典型的Co系催化剂工业操作条件范围(T=473～503 K,p=1.5～4.0 MPa, H2/CO体积比=1.0～3.0)内,采用等温积分固定床反应器对Co/ZrO2/SiO2催化剂进行了F-T合成反应动力学研究. 依据详细可靠的基元反应机理,按照Langmuir-Hinshelwood-Hougen-Watson动力学推导方法,获得了Co系催化剂上基于详细反应机理的动力学模型. 通过动力学实验数据的回归分析,发现基于COs直接解离并以烷基为链增长中间体的表面碳物种机理的动力学模型可以较好地描述Co/ZrO2/SiO2催化剂上的F-T合成反应结果,该模型可自洽地描述F-T合成过程中的合成气消耗和烃产物分布状况,且获得的反应活化能等关键动力学参数与文献报道的理论结果基本一致.     

利用高通量技术研究钴基费托催化剂的宏观动力学

利用高通量技术设计并运行了16路平行动力学固定床反应器,用于测量不同接触时间下的稳态反应物消耗速率和产物生成速率,研究了钴基费托催化剂的宏观动力学,包括C1～C4烷烃与烯烃的稳态反应速率及其随床层的分布,以及它们与反应器温度的关系.在等温固定床非扩散限制的反应条件下,除C1和C2烃类外,Cn的生成速率及CO/H2的消耗速率均随接触时间的增加先上升后下降,且烯烃生成速率的最高点较烷烃更靠近反应器入口;反应温度对速率的影响与转化率有关:生成烷烃的表观活化能大于烯烃.高通量动力学反应器可用于生成宏观动力学数据库,以预测催化剂在工业固定床反应器中的行为.     

工业固定床Fe-Cu-K催化剂浆态床F-T合成适应性研究

采用连续搅拌釜式反应器,在接近F-T合成实际工况下考察了工业固定床Fe-Cu-K催化剂浆态床F-T合成反应性能，研究反应温度、压力、原料气空速和氢碳摩尔比等操作参数对催化剂反应活性、产物选择性和稳定性的影响，实验总运转时间达2 500 h；同时采用扫描电镜技术（SEM）对催化剂的抗磨损性能进行了研究，结果表明，操作参数对催化剂的活性、选择性和目标产物产率有较大的影响，工业固定床Fe-Cu-K催化剂具有一定的抗磨损性能，F-T合成烃产物分布合理；催化剂具有较高的稳定性，在589 h的稳定条件运行内，催化剂的失活速率为0.23%/d（以CO转化率的降低计）；在整个运行期间CH4选择性维持在较低的水平。     

甲醇制烯烃反应过程中SAPO-34催化剂积炭动力学研究

在固定床反应器中研究了甲醇制烯烃反应过程中SAPO-34分子筛催化剂的积炭动力学，分别得到了催化剂积炭量与反应温度、剂醇比的经验关联式。结果表明，催化剂床层存在明显的积炭分布，在450 ℃，甲醇WHSV为15 h－1，催化剂积炭量随催化剂反应运行时间（Time on Stream, TOS）为25 min时，床层入口处的积炭量平均为9.56%，而出口处的积炭量平均为3.20%，属于平行失活，积炭主要来源于甲醇生成的高碳中间体，这些中间体在生成低碳烃的同时生成积炭。从积炭的生成机理出发，得到了SAPO-34分子筛催化剂的积炭动力学机理模型，将催化剂积炭量与一定催化剂停留时间内反应过程中甲醇的转化量相关联，该模型形式同样简单，能够较好地拟合实验数据。     

Co/ZrO2/SiO2催化剂上费-托合成反应动力学研究Ⅰ. 反应途径分析

 采用单位键指标-二次指数势(UBI-QEP)方法对模型催化剂Co(0001)晶面进行了费-托(F-T)合成反应的反应能学分析,发现以不含氧的CxHy,s 作为中间体的表面碳化物机理在能量上较为合理,而CH2,s 作为链增长单体的链增长方式是能量上最有利的F-T合成反应途径. 在Co/ZrO2/SiO2催化剂上的非稳态实验研究中发现,在F-T合成的操作温度范围内,H2O的生成是主要的表面O的移去方式; CO解离和表面碳物种Cs加氢可能是F-T合成中的重要速控步骤; 链增长过程是F-T合成反应中较快的基元反应步骤; 甲烷的生成具有多种不同活性的表面前驱体,导致生成的甲烷严重偏离经典的ASF分布规律. 结合F-T合成表面反应的研究结果,初步确定了F-T合成动力学研究中需要考虑的机理模型的范围是以CO解离和表面碳物种Cs加氢为速控步骤,以CH2,s 插入为链增长途径的表面碳化物机理. 该结果缩小了待选动力学模型的范围.     

强酸性阳离子交换树脂催化合成醋酸正丁酯的动力学研究

以强酸性阳离子交换树脂Amberlyst 15作为催化剂,研究了醋酸与正丁醇合成醋酸正丁酯的反应动力学;考察了搅拌速度、催化剂粒径、温度、催化剂用量,以及酸醇物质的量之比对醋酸转化率的影响;建立了拟均相动力学模型,对实验数据进行了拟合,并估算了相应的动力学参数.结果表明,由拟均相动力学模型得到的计算值与实验值吻合较好.     

B108中温变换催化剂宏观动力学的研究

常压下以内循环无梯度反应器研究了B108铁基中温变换催化剂上水煤气变换反应宏观动力学。测定了反应速率,并用马夸特非线性参数估值法获得了幂函数宏观动力学模型r_s=37.67exp(-43982/RT)y_(CO)~(0.7552)y_(H_2O)~(-0.0367)Y_(CO_2)~(-0.4874)y_(H_2)(1-β)根据方差分析和残差分析,证实模型是高度显著的。由实验数据计算出相应反应条件下的效率因子。内扩散对原粒度B108催化剂上的反应具有严重影响。模型用于工业变换炉催化剂的用量核算,模型值与实际值符合良好。     

在HZSM-5分子筛催化剂上苯-乙烯烷基化合成乙苯动力学的研究

近年来,有不少关于各种沸石分子筛上苯—乙烯烷基化反应的研究报道,但动力学的研究报道不多。Becker等研究了在氢型丝光沸石上乙苯合成动力学,得到速率方程r=kP_(苯~(0.6))P_(乙烯~(0.6))。我们以本研究室制备的HZSM-5型分子筛作为催化剂进行了苯—乙烯烷基化反应动力学的研究。为有效地排除扩散影响并使催化剂上各点浓度与温度均匀,直接准确测定反应速率,实验系在磁驱动的内循环无梯度反应器中进行,得到了速率方程及动力学参数。     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Copper catalyzed/mediated synthetic methodology for ebselen and related isoselenazolones

Scope of the copper catalyzed/mediated selenium-nitrogen coupling reaction has been studied for the synthesis of isoselenazolones. It is noticed that the 2-chloro, 2-bromo-, and 2-iodo-aryl amides substrates can be exploited in the selenium-nitrogen coupling reaction by employing 25-100 mol % of CuI/1,10-phenanthroline (L) and potassium carbonate as a base in DMF. Furthermore, electron rich 2-chloro-arylamides also underwent selenium-nitrogen coupling reaction to give biologically important selenium-nitrogen heterocycles. Also, copper-catalyzed selenium-nitrogen coupling reaction has been meticulously applied for the synthesis of diaryl diselenides having methoxy, amine, and amide functionality from respective aryl iodides in the presence of stoichiometric amount of succinimide as an external Se-N coupling partner.     

Knoevenagel condensation catalyzed by novel Nmm-based ionic liquids in water

A series of novel N-methyl morpholine (Nmm) based ionic liquids with 1,2-propanediol group were synthesized and used as catalysts for Knoevenagel condensation at room temperature in water. Under the effect of the catalyst, various aldehydes or aliphatic ketones could react with a wide range of activated methylene compounds well, including malononitrile, alkyl cyanoacetate, cyanoacetamide, β-diketone, barbituric acid, 2-arylacetonitrile and thiazolidinedione. Furthermore, most of the products could be separated just by filtrating and washing with water. Additionally, the catalyst is recyclable and applicable for the large-scale synthesis.     

Construction of polyheterocyclic spirotetrahydrothiophene derivatives via sulfa-Michael/aldol cascade reaction

A series of polyheterocyclic spirotetrahydrothiophene derivatives were obtained in moderate to excellent yields via a catalyst-free sulfa-Michael/aldol cascade reaction of chalcones 1 and commercially available 1,4-dithiane-2,5-diol 2 under mild conditions. We also present the first asymmetric sulfa-Michael/aldol cascade reaction of chalcones 1 and commercially available 1,4-dithiane-2,5-diol 2 with moderate to good enantioselectivities catalyzed by readily available chiral phase-transfer catalysts (PTCs).     

Suzuki-Miyaura reactions of the soluble guanylate cyclase inhibitor NS2028: a non-product specific route to C-8 substituted analogues

Both soluble guanylate cyclase (sGC) inhibitors ODQ 1 and NS2028 2 are synthesized via improved protocols. In the former case treating 3,4-dihydroquinoxalin-2(1H)-one oxime 8, which can be prepared in two steps from 1,2-benzenediamine, with 1,1′-carbonyldiimidazole (CDI) gives the dihydro-ODQ 10 that in the presence of KMnO₄ oxidises to give ODQ 1 in an overall yield of 46% starting from 1,2-benzenediamine. In the latter case, the synthesis affords NS2028 2 from 2-amino-4-bromophenol 3 in three steps with an overall yield of 85% and avoids the need for chromatography. Furthermore, Suzuki-Miyaura reaction conditions are described that enable the preparation of 8-aryl and 8-heteroaryl derivatives of NS2028 directly from NS2028 2. Finally, demethylation of the 8-(methoxyphenyl) substituted analogues afforded the 8-(hydroxyphenyl) derivatives 40-42. All new products are fully characterised.     

Sodium carbonate mediated regioselective synthesis of novel N-(hydroxyalkyl)cinnamamides

A synthetic protocol for the direct synthesis of N-(hydroxyalkyl)cinnamamides from cinnamates and aminoalcohols in the presence of sodium carbonate as the base is presented. A wide variety of N-(hydroxyalkyl)cinnamamides were isolated in up to 99% yields. The reaction is highly regioselective and yields only N-acylated products by 1,2-addition of aminoalcohols to cinnamates.     

NaNO2/I2 as an alternative reagent for the synthesis of 1,2,3-benzotriazin-4(3H)-ones from 2-aminobenzamides

An efficient transformation of 2-aminobenzamides to 1,2,3-benzotriazin-4(3H)-ones in the presence of sodium nitrite (NaNO₂) and Iodine (I₂) is described. The reaction is proposed to proceed via formation of nitrosyl halide that induces nitrosylation of the amino group of 2-aminobenzamide leading to diazotization followed by intramolecular cyclization.