微波消解-电感耦合等离子体质谱法测定车用催化剂中铂、钯、铑

提出了电感耦合等离子体质谱法同时测定车用催化剂中铂、钯和铑的含量。样品0.100 0g经盐酸6mL、硝酸3mL、氢氟酸1mL和水4mL消解,选择195Pt、105Pd和103 Rh为待测同位素。铂、钯和铑的检出限(3σ)分别为0.003,0.5,0.002μg·L-1。方法用于5种催化剂样品的分析,测定结果与另两家实验室测定结果相一致。铂、钯和铑的回收率在85.5%～101%之间。     

贵金属负载的棒状ZnO复合光催化剂的制备及其提升的光催化性能

以水热制备的ZnO纳米棒为基底,通过乙二醇液相还原法负载不同贵金属颗粒(Pt、Pd、Ru)构筑贵金属负载的ZnO纳米棒复合光催化剂。实验结果表明在制备条件相同时,Pt/ZnO样品中Pt颗粒尺寸较小,分布均匀;Pd/ZnO样品中Pd颗粒尺寸较大且团聚严重;Ru/ZnO样品则几乎没有Ru颗粒负载。在紫外光照射下降解亚甲基蓝的反应中,Pt/ZnO表现出最高的光催化性能,Pd/ZnO样品次之,而Ru/ZnO则表现出与ZnO纳米棒相似的光催化活性;表明小尺寸和大小均匀的贵金属颗粒对ZnO纳米棒的催化性能有着显著的提升作用。对Pt/ZnO来说,当Pt载量为3.2%时Pt/ZnO催化剂的光催化活性最高。     

ICP-AES测定废Al2O3基催化剂中Pt、Pd

研究了废Al2O3基催化剂中Pt,Pd的ICP－AES测定新方法。以王水溶解样品，在HCl(5 95)介质中，用工作曲线法对废Al2O3基催化剂中的Pt,Pd直接进行测定，不需进行基体匹配。方法的检出限分别为：Pt 0.1μg/mL，P 0.045μg／mL；样品的加标回收率为Pt 95.2%-105.5%,Pd 95.3%-100.6%;RSD(n=6)均＜9％。     

CeO2基氧化物储氧材料研究(Ⅱ)添加贵金属改进储氧能力

在高温老化的复合氧化物CZO和CZYO体系中,添加微量贵金属(Pt,Pd,Rh)明显提高还原速度并增加OSC.含贵金属的CZO或CZYO的OSC与其组成和贵金属的种类有关.较长时间(10 h)老化后含Pd的CZO3样品的OSC明显下降,CZYO2样品的OSC略有下降.含Pt/Rh,10 h老化后CZO3和CZY02样品的OSC均高于相应同条件老化的含Pd样品的OSC.     

CeO2基氧化物储氧材料研究(Ⅱ)添加贵金属改进储氧能力

在高温老化的复合氧化物CZO和CZYO体系中,添加微量贵金属(Pt,Pd,Rh)明显提高还原速度并增加OSC.含贵金属的CZO或CZYO的OSC与其组成和贵金属的种类有关.较长时间(10 h)老化后含Pd的CZO3样品的OSC明显下降,CZYO2样品的OSC略有下降.含Pt/Rh,10 h老化后CZO3和CZY02样品的OSC均高于相应同条件老化的含Pd样品的OSC.     

有序介孔三氧化二锰负载PdPt合金:一种高效的甲烷催化燃烧催化剂

甲烷作为一种清洁廉价的碳氢能源,广泛应用于运输业和其它工业领域.但是其本身是一种比二氧化碳导致全球变暖效应更强的温室气体,而且甲烷直接燃烧会产生其它污染物,比如一氧化碳、氮氧化物、未充分燃烧的碳氢化合物等.因此有必要开展有关甲烷催化燃烧的研究工作,以大幅度降低起燃温度,提高燃烧效率,有效地减少污染副产物的产生.由于具有较好的低温催化活性,Pd基催化剂常用于甲烷的催化燃烧.但是Pd基催化剂也存在一些亟需解决的问题,比如在催化燃烧过程中活性相结构不稳定.PdO通常被认为是碳氢化合物催化氧化中的活性相,但是在高温下PdO分解为Pd,导致催化活性下降.PdO遇到含水或硫的化合物时会生成惰性的Pd(OH)2或稳定的硫化物,造成活性物种的流失,从而降低催化剂的性能.如果在材料中添加另一种贵金属Pt,使之与Pd一起形成贵金属合金,则可提高其低温催化燃烧的活性,增加Pd基催化剂的热稳定性以及抗水和抗硫能力.另一方面,过渡金属氧化物价格便宜,热稳定性以及抗硫性较好,也常作为甲烷燃烧的催化剂.其中三氧化二锰由于具有可变的氧化态以及较好的储氧能力受到了广泛关注.本课题组采用KIT-6作为硬模板,先合成具有有序介孔结构的Mn2O3(meso-Mn2O3)纳米催化剂,然后通过聚乙烯醇(PVA)保护的液相共还原法分别制备meso-Mn2O3担载Pd,Pt及PdPt合金的纳米催化剂(x(PdyPt)/meso-Mn2O3;x=(0.10-1.50)wt%;Pd/Pt摩尔比(y)=4.9-5.1).XRD结果表明,合成的meso-Mn2O3具有立方相晶体结构.其BET比表面积为106 m2/g.由TEM照片可观察到粒径范围为2.1?2.8 nm的贵金属纳米颗粒均匀分散在meso-Mn2O3表面.通过XPS分析可知,结合能在529.6和531.2 eV的峰可分别归属于晶格氧(Olat)和表面吸附氧(Oads).Pd0和Pd2+以及Pt0和Pt2+也均可通过曲线拟合后进行分峰确定.XPS定量分析结果表明,样品的Oads/Olat摩尔比有如下顺序:1.41(Pd5.1Pt)/meso-Mn2O3(0.77)>1.40Pd/meso-Mn2O3(0.69)>0.72(Pd5.1Pt)/meso-Mn2O3(0.65)>1.42Pt/meso-Mn2O3(0.63)>0.07(Pd4.9Pt)/meso-Mn2O3(0.53)>0.07(Pd4.9Pt)/bulk-Mn2O3(0.52)>meso-Mn2O3(0.45),这与其催化活性的顺序一相致.该结果表明,高的吸附氧物种浓度有利于甲烷催化燃烧.负载Pd,Pt或PdPt以后的样品的表面吸附氧物种浓度显著提高,催化活性最好的1.41(Pd5.1Pt)/meso-Mn2O3样品具有最高的吸附氧物种浓度.负载PdPt合金可有效提高催化剂对甲烷燃烧的催化活性.1.41(Pd5.1Pt)/meso-Mn2O3催化剂的活性最好:在空速为20000 mL/(g.h)的条件下,甲烷燃烧的T10%,T50%和T90%分别为265,345和425oC.此外,还考察了引入一定量的SO2,CO2,H2O和NO对甲烷在1.41(Pd5.1Pt)/meso-Mn2O3催化剂上氧化反应的影响,发现引入少量的Pt可提高催化剂抗SO2,CO2和H2O的能力,但是NO对甲烷燃烧的还原效应也不可忽视.基于催化剂物化性质的表征结果和活性数据,我们认为1.41(Pd5.1Pt)/meso-Mn2O3优异的催化性能与其拥有高质量的三维有序多孔结构、高的吸附氧物种浓度、优良的低温还原性以及Pd-Pt合金与meso-Mn2O3载体之间的强相互作用有关.     

萘在贵金属Pd、Pt及Pd-Pt催化剂上的加氢活性及耐硫性能

采用等体积浸渍法制备了SiO2-Al2O3负载的Pd、Pt单金属催化剂及Pd/Pt摩尔比分别为1∶1、1∶4、4∶1的双金属催化剂(Pd1Pt1、Pd1Pt4、Pd4Pt1),对其进行X射线衍射(XRD)、透射电镜(TEM)、CO化学吸附和X射线光电子能谱(XPS)表征,并详细考察了各催化剂的萘加氢活性和耐硫性能.结果表明,在实验考察范围内,Pd4Pt1催化剂上的萘转化率最高可达98.2%,全饱和产物十氢萘选择性最高可达93.6%,十氢萘反/顺生成率之比最高可达7.8,均高于单金属Pd(97.5%,59.1%,4.3)和Pt(96.8%,39.9%,2.9)催化剂的值.萘在三种催化剂上的加氢速率顺序为vPd4Pt1vPdvPt.添加二苯并噻吩(DBT)后Pd4Pt1上的萘转化率和十氢萘选择性仍然最高,十氢萘反/顺比在Pt催化剂上不受影响,在Pd4Pt1催化剂上稍有降低,而在Pd催化剂上降低明显.在三种不同Pd/Pt摩尔比的双金属催化剂中,Pd4Pt1催化剂上的萘转化率和十氢萘选择性在添加DBT前后都是最佳的.     

结合动力学和热力学研究PtPd修饰Zn_(0.5)Cd_(0.5)S纳米棒体系的高效光催化产氢机理（英文）

硫化镉锌(Zn_(0.5)Cd_(0.5)S)纳米棒因其制备方法简单以及具有良好的光催化活性等优点,在光催化领域得到广泛的研究和应用.单一Zn_(0.5)Cd_(0.5)S存在光生电子与空穴易复合以及光腐蚀等问题,采用助催化剂修饰将有助于电荷分离与迁移,从而提高其光催化性能.本文将Pt Pd合金作为助催化修饰Zn_(0.5)Cd_(0.5)S纳米棒光催化材料,以提高可见光照射下的产氢速率,并对合金助催化剂提高催化活性的机理进行了深入研究.通过简单水热法合成Zn_(0.5)Cd_(0.5)S,采用化学还原沉积法制备Pt Pd/Zn_(0.5)Cd_(0.5)S复合光催化材料.XRD结果表明,成功合成了Zn_(0.5)Cd_(0.5)S催化剂.TEM结果表明,Zn_(0.5)Cd_(0.5)S呈纳米棒状,测量得到Pt Pd合金的(111)晶面条纹间距为0.23 nm,说明合金成功负载到硫化镉锌上.XPS结果表明,Pt Pd/Zn_(0.5)Cd_(0.5)S复合样品中Pt和Pd元素的峰值较Pt/Zn_(0.5)Cd_(0.5)S和Pd/Zn_(0.5)Cd_(0.5)S均发生了偏移,Pt和Pd元素化学结合环境发生改变,进一步证实合成了Pt Pd合金.光催化产氢实验结果表明,当Zn_(0.5)Cd_(0.5)S负载Pt Pd合金以后,光催化产氢速率大幅提升,其中负载量为1.0 wt%的Pt Pd/Zn_(0.5)Cd_(0.5)S复合光催化材料的产氢速率最快,达到9.689 mmol·g~(–1)·h~(–1),分别是纯Zn_(0.5)Cd_(0.5)S,Pt/Zn_(0.5)Cd_(0.5)S和Pd/Zn_(0.5)Cd_(0.5)S的9.5,3.6和1.7倍.为了探究Pt Pd合金性能优于Pt的原因,本文结合化学反应热力学(DFT理论计算)和动力学(光致发光光谱、光电流响应、电化学阻抗谱和表面光电压谱)手段进行了详细研究.结果表明,PtPd二元贵金属合金具有与Pt相近的氢活性物种吸附能和d带中心,可以大大加速电荷转移,促进电荷分离,降低H_2生成的活化能.虽然Pt在热力学上有利于光催化产氢,但从催化反应动力学结果可知,PtPd合金在动力学上更有利于产氢,这与光催化产氢结果一致,即Pt Pd/Zn_(0.5)Cd_(0.5)S复合材料催化活性高于Pt/Zn_(0.5)Cd_(0.5)S.综上,本文研究结果可为其他金属合金助催化剂的研究提供新思路.     

示踪原子——离子交换法研究铑和铂、钯、铱的分离

本文以~(197)Pt、~(103)Pd和~(192)Ir为示踪原子,用离子交换法研究了常量Rh和小量Pt、Pd、Ir的分离。将Rh和Pt、Pd、Ir的盐酸溶液通过阳离子交换树脂往后,先用1M H Cl淋出Pt、Pd和Ir后,再用6M H Cl淋出Rh使Rh和Pt、Pd、Ir得到定量分离。     

冠醚分离锂同位素中冠醚的近红外分析

将近红外光谱法(NIR)和偏最小二乘法(PLS)相结合，建立了冠醚分离锂同位素中冠醚含量的分析方法，研究了锂、钠、钾离子的存在对冠醚测定的影响，并研究了不同离子液体对校正模型的影响。该方法的测定范围为0.1～1.2 mol/L,加入校正样品后，可扩大测定范围。冠醚分离锂同位素实验样品分析结果和设计值较吻合，加标回收率为105%～108%。所建立的方法为锂同位素分离工艺中冠醚的快速分析提供了一种新方法。     

Investigation of ICP-MS spectral interferences in the determination of Rh, Pd and Pt in road dust: Assessment of correction algorithms via uncertainty budget analysis and interference alleviation by preliminary acid leaching

A method for classification of the potential spectral interferences in inductively coupled plasma mass spectrometry (ICP-MS) was proposed based on statistical assessment of the interfering signals. The concept was applied to investigate the variety of spectral interferences over the isotopes of Rh, Pd and Pt concerning their analysis in road dust samples. For the significant interferences the applicability of mathematical corrections using two alternative algorithms were studied by uncertainty budget analysis and the approach resulting in lower combined uncertainty of the corrected signals was selected. Further the uncertainty evaluation was used for assessment of the most appropriate Pd isotope to be measured. The adequateness of the mathematical corrections for Rh and Pd was highly relevant to the number of elements causing spectral interferences and the relative analyte/interferent concentrations. This was overcome by preliminary road dust leaching with 0.35 mol l⁻¹ hydrochloric acid. Interferents present as easily soluble salts were substantially removed form the samples while the platinum group metals were not leached which allowed a relative analyte preconcentration to be obtained. For the leached samples the isotopes of Rh and Pd were still spectrally interfered from Sr, Y and Pb but at considerably lesser degree thus after mathematical correction the ICP-MS analysis of Rh, Pd and Pt was reliable and robust using the isotopes 103, 105 and 195, respectively. The method was validated via an alternative analysis based on selective separation of the platinum group metals by microwave-assisted cloud point extraction.     

Isotope dilution inductively coupled plasma quadrupole mass spectrometry in connection with a chromatographic separation for ultra trace determinations of platinum group elements (Pt, Pd, Ru, Ir) in environmental samples

An isotope dilution inductively coupled plasma quadrupole mass spectrometric (ID-ICP-QMS) method was developed for the simultaneous determination of the platinum group elements Pt, Pd, Ru, and Ir in environmental samples. Spike solutions, enriched with the isotopes 194Pt, 108Pd, 99Ru, and 191Ir, were used for the isotope dilution step. Interfering elements were eliminated by chromatographic separation using an anion-exchange resin. Samples were dissolved with aqua regia in a high pressure asher. Additional dissolution of possible silicate portions by hydrofluoric acid was usually not necessary. Detection limits of 0.15 ng x g(-1), 0.075 ng x g(-1), and 0.015 ng x g(-1) were achieved for Pt, Pd, Ru, and Ir, respectively, using sample weights of only 0.2 g. The reliability of the ID-ICP-QMS method was demonstrated by analyzing a Canadian geological reference material and by participating in an interlaboratory study for the determination of platinum and palladium in a homogenized road dust sample. Surface soil, sampled at different distances from a highway, showed concentrations in the range of 0.1-87 ng x g(-1). An exponential decrease of the platinum and palladium concentration with increasing distance and a small anthropogenic contribution to the natural background concentration of ruthenium and iridium was found in these samples.     

Synthesis of ultrathin FePtPd nanowires and their use as catalysts for methanol oxidation reaction

We report a facile synthesis of ultrathin (2.5 nm) trimetallic FePtPd alloy nanowires (NWs) with tunable compositions and controlled length (<100 nm). The NWs were made by thermal decomposition of Fe(CO)(5) and sequential reduction of Pt(acac)(2) (acac = acetylacetonate) and Pd(acac)(2) at temperatures from 160 to 240 °C. These FePtPd NWs showed composition-dependent catalytic activity and stability for methanol oxidation reaction. Among FePtPd and FePt NWs as well as Pd, Pt, and PtPd nanoparticles (NPs) studied in 0.2 M methanol and 0.1 M HClO(4) solution, the Fe(28)Pt(38)Pd(34) NWs showed the highest activity, with their mass current density reaching 488.7 mA/mg Pt and peak potential for methanol oxidation decreasing to 0.614 V from 0.665 V (Pt NP catalyst). The NW catalysts were also more stable than the NP catalysts, with the Fe(28)Pt(38)Pd(34) NWs retaining the highest mass current density (98.1 mA/mg Pt) after a 2 h current-time test at 0.4 V. These trimetallic NWs are a promising new class of catalyst for methanol oxidation reaction and for direct methanol fuel cell applications.     

Interaction of palladium(II) and platinum(II) complexes with microperoxidase-11 studied by electrospray mass spectrometry and MS/MS analysis

Interactions of cis-[Pd(en)(H(2)O)(2)](2+) (en, ethylenediamine) and cis-[Pt(NH(3))(2)(H(2)O)(2)](2+) with microperoxidase-11 (MP-11) in a molar ratio of 1:1 or 2:1 at pH 1.4 were investigated via electrospray mass spectrometry and MS/MS analysis at room temperature and at 40 degrees C with an incubation time of 2 or 3 days. The composition of the Pd(II)- and Pt(II)-anchored MP-11 was confirmed on the basis of the precise molecular mass and the simulated isotope distribution pattern. MS/MS analysis revealed that the Pd(II) center anchored to the side chain of Cys7 as Pd(II) and MP-11 were mixed in an equimolar ratio and to side chains of Cys7 and Cys4 as Pd(II) and MP-11 mixed in a 2:1 molar ratio. When Pt(II) and MP-11 were mixed in a 2:1 molar ratio, Pt(II) first anchored to the side chain of Cys7, and then to the side chain of Cys4 with time. The initial coordination of Pd(II) and Pt(II) to the side chain of Cys7 is the essential step for the Pd(II)- and Pt(II)-promoted cleavage of the His8-Thr9 bond in MP-11. These results support the hypothesis that the Pd(II)-mediated cleavage of the His18-Thr19 bond in cytochorome c is due to the identical binding mode.     

Atomically Dispersed Copper–Platinum Dual Sites Alloyed with Palladium Nanorings Catalyze the Hydrogen Evolution Reaction

Designing highly active catalysts at an atomic scale is required to drive the hydrogen evolution reaction (HER). Copper–platinum (Cu‐Pt) dual sites were alloyed with palladium nanorings (Pd NRs) containing 1.5 atom % Pt, using atomically dispersed Cu on ultrathin Pd NRs as seeds. The ultrafine structure of atomically dispersed Cu‐Pt dual sites was confirmed with X‐ray absorption fine structure (XAFS) measurements. The Pd/Cu‐Pt NRs exhibit excellent HER properties in acidic solution with an overpotential of only 22.8 mV at a current density of 10 mA cm⁻² and a high mass current density of 3002 A g⁻¹_(Pd+Pt) at a −0.05 V potential.     

Pd/Pt core–shell nanowire arrays as highly effective electrocatalysts for methanol electrooxidation in direct methanol fuel cells

Highly ordered Pd/Pt–core–shell nanowire arrays (Pd/Pt NWAs) have been prepared by anodized aluminum oxide (AAO) template-electrodeposition and magnetron sputtering methods. Pd/Pt NWA electrode shows a very high electrochemical active surface area and high electrocatalytic activity for the methanol electrooxidation in acid medium for direct methanol fuel cells (DMFCs). The mass specific anodic peak current density is 756.7 mA mg⁻¹ Pt for the methanol oxidation on the Pd/Pt NWA electrode, an increase by a factor of four as compared to conventional E-TEK PtRu/C electrocatalysts. The mechanism of the significant enhancement of the Pd/Pt core/shell NWA nanostructure in the efficiency and electrocatalytic activity of Pt for the methanol electrooxidation in acid medium is discussed.     

Pt单层修饰Pd/C氧还原催化剂

分别利用液相热解法和浸渍还原法制备了碳载钯纳米催化剂（Pd/C）,并研究了其对氧还原反应的电催化活性。与浸渍还原法相比,液相热解法得到的Pd/C催化剂虽然粒径较大,但表现出较好的氧还原反应（ORR）活性和稳定性.在所制备的Pd/C催化剂基础上,通过置换欠电势沉积的Cu原子单层,获得了Pt单层修饰的Pd/C催化剂,其ORR活性较Pd/C催化剂有显著提高,且与纯Pt/C催化剂接近,而其耐久性则较纯Pt/C催化剂有显著提升,显示出Pt单层催化剂的潜在优势.     

Oxygen reduction reaction on the low index planes of palladium electrodes modified with a monolayer of platinum film

Oxygen reduction reaction (ORR) has been studied on the low index planes of Pd modified with a monolayer of Pt (Pt/Pd(hkl)) in 0.1 M HClO₄ with the use of hanging meniscus rotating disk electrode. The activity for ORR on bare Pd(hkl) electrode depends on the surface structure strongly, however, voltammograms of ORR on Pt/Pd(hkl) electrodes do not depend on the crystal orientation. The specific activities of Pt/Pd(hkl) electrodes at 0.90 V (RHE) are higher than that on Pt(1 1 0) which has the highest activity for ORR in the low index planes of Pt. The mass activity on Pt/Pd(hkl) electrode is 7 times as high as a commercial Pt/C catalyst.     

Determination of bismuth, indium and lead in geological samples by electrothermal AAS Part 2. Comparative study of palladium and molybdenum containing chemical modifiers*

A comparative and systematic study has been carried out of the effects of palladium and molybdenum containing chemical modifiers, such as Pd + Rh, Pd + Pt, Pd + Ru, Pd + Rh + Pt, Pd + Rh + Ru, Mo + Pd, Mo + Rh, Mo + Ru and Mo + Pt and additionally tartaric acid (TA) as a reducing agent together with mixed modifiers for the thermal stabilization of Bi, In and Pb in a Zeeman electrothermal atomic absorption spectrometer (ETAAS). The effect of the mass ratios of the mixed modifier components on the maximum pretreatment temperature for the analytes has been determined. The modifier mixtures of Pd + Rh + Pt, Mo + Pd + TA and Mo + Pt + TA were found to be especially powerful for the determination of Bi, In and Pb. These mixed modifiers could increase the ashing temperatures of the analytes up to 1250–1400° C. They were applied to the determination of Bi and Pb in dissolved geological reference samples and accuracy and precision of the method were thereby enhanced. The percent relative error was decreased from 20.0 to 0.4 for Bi and from 10.5 to 0.3 for Pb, depending on the sample type. Received: 9 May 1997 / Revised: 19 August 1997 / Accepted: 20 August 1997     

Determination of bismuth, indium and lead in geological samples by electrothermal AAS Part 2. Comparative study of palladium and molybdenum containing chemical modifiers*

A comparative and systematic study has been carried out of the effects of palladium and molybdenum containing chemical modifiers, such as Pd + Rh, Pd + Pt, Pd + Ru, Pd + Rh + Pt, Pd + Rh + Ru, Mo + Pd, Mo + Rh, Mo + Ru and Mo + Pt and additionally tartaric acid (TA) as a reducing agent together with mixed modifiers for the thermal stabilization of Bi, In and Pb in a Zeeman electrothermal atomic absorption spectrometer (ETAAS). The effect of the mass ratios of the mixed modifier components on the maximum pretreatment temperature for the analytes has been determined. The modifier mixtures of Pd + Rh + Pt, Mo + Pd + TA and Mo + Pt + TA were found to be especially powerful for the determination of Bi, In and Pb. These mixed modifiers could increase the ashing temperatures of the analytes up to 1250–1400° C. They were applied to the determination of Bi and Pb in dissolved geological reference samples and accuracy and precision of the method were thereby enhanced. The percent relative error was decreased from 20.0 to 0.4 for Bi and from 10.5 to 0.3 for Pb, depending on the sample type. Received: 9 May 1997 / Revised: 19 August 1997 / Accepted: 20 August 1997