带有端烷烃链的超支化聚酯的受限结晶及动态黏弹行为

以三羟甲基丙烷(TMP)为核,二羟甲基丙酸(DMPA)为支化单体,通过熔融缩聚法合成了第3代端羟基脂肪族超支化聚酯,并用十八酸对其进行端基改性,采用广角X射线衍射(WAXD)、示差扫描量热分析(DSC)及红外光谱(FTIR)研究了不同端基改性程度的超支化聚酯的结晶熔融行为及端烷烃链的构象和堆积结构随温度的变化,采用旋转流变仪研究了端烷烃链对脂肪族超支化聚酯熔体动态黏弹行为的影响.结果表明,这类改性超支化聚酯的结晶归因于长链端烷烃的有序排列,改性程度越高,衍射峰强度越大.受限结晶的端烷烃链在升温后并不能完全转变为无序的结构状态,改性超支化聚酯在"熔点"以上仍有部分有序结构存在.超支化聚酯的线性黏弹区随着端基改性程度的增大而逐渐变短,超支化聚酯的弹性逐渐增大,剪切变稀越明显.动态流变测试中所出现的现象与改性超支化聚酯中端烷烃链的受限密切相关.     

含亚环己基荷电聚醚醚酮的合成表征与性能

以 3,3′ 二磺酸钠基 4,4′ 二氟二苯酮和 4,4′ 二氟二苯酮与 4,4′ 亚环己基双酚进行亲核共缩聚 ,合成了磺化度从 0 4～ 2 0的一系列含亚环己基的荷电聚醚醚酮 .聚合物除保持了荷电聚醚醚酮良好的热稳定性和机械性能外 ,还具有良好的耐水性 .聚合物的DSC和广角X射线衍射数据表明 :上述磺化度聚合物均呈无定型聚集态结构 .比较了聚合物与双酚A系列荷电聚醚醚酮的性能差异 ,讨论了聚合物的溶解特点     

含混杂活性端基新型多官能团齐聚物的结构与性能

通过控制4,4'-二氨基二苯甲烷环氧树脂(TGDDM)和丙烯酸(AA)的摩尔比(1∶2)合成了化学共混的含混杂活性端基的多官能团齐聚物MVEO-2,直接将多官能团环氧树脂TGDDM与多官能团环氧乙烯基树脂MVER通过物理共混得到聚合物共混物MVEOmix.研究了化学共混和物理共混对含混杂活性端基多官能团齐聚物的结构、性能和形态的影响.红外光谱(FTIR)和核磁共振谱(1H NMR)表明,MVEO-2和MVEOmix具有相同的结构组成.凝胶渗透色谱(GPC)分析表明MVEOmix具有双峰结构且分子量分布较窄,而MVEO-2具有多峰结构且分子量分布较宽.热重分析(TGA)和动态热机械分析(DMA)表明,MVEO-2的热稳定性比MVEOmix更高.MVEO-2的强度和韧性比MVEOmix明显提高,弯曲强度提高17%,拉伸强度提高38%,断裂伸长率提高35%,冲击强度提高24%.扫描电镜结果表明化学共混形成了更均匀紧密的互穿聚合物网络结构.     

侧基含偶氮苯生色团的短梗霉多糖的制备及光致变色性

利用4-(4-硝基苯偶氮)-1-萘酚的丙烯酸酯与短梗霉多糖进行接枝共聚,制备了侧基含偶氮苯生色团的短梗霉多糖聚合物,并用红外光谱、扫描电镜、X射线衍射、热重分析等手段对聚合物进行了表征.用紫外光谱研究了聚合物的光致变色性,结果表明聚合物具有良好的热稳定性和光致变色性.     

关于聚合物非晶态X衍射表征函数的探讨

电子计算机X射线衍射分峰法是70年代发展起来的有价值的研究结晶聚合物结构的新方法,其可靠性首先取决于用以表示晶志衍射与非晶态衍射的表征函数是否正确。本文讨论了现有的各种非晶态衍射表征函数的缺点,作者在实验和理论分析的基础上,提出两个不对称的指数函数作为聚合物非晶态X衍射表征函数。把这函数应用于聚丙烯的结构分析并与应用其他类型的表征函数所得的结果相比较,证明作者提出的不对称指数函数形式的非晶态X衍射表征函数能给出比较满意的结果。     

聚合物不同相态X-射线衍射的数学描述

<正> 由于电子计算机的迅速发展和广泛应用,使得已被国内外普遍用来研究聚合物结构的“分峰法”(分解聚合物的X-射线衍射重叠峰的方法)成为一个切实可行的、有效的新方法。分峰法的前提和基础是要有反映聚合物各相态X-射线衍射峰峰形规律的合理的和确切的数学模型,这对聚合物结构的研究有着直接的重要的影响。七十年代迄今,国内外现有的关于聚合物不同相态的X-射线衍射的数学描述尚无通用的、统一的形式,     

聚酚酞醚砜-聚硅氧烷-聚醚氨酯多嵌段聚合物

<正> 合成了端异氰酸酯基聚硅氧烷-聚醚氨酯嵌段预聚物和端羟基酚酞醚砜齐聚物,探索了上述预聚物与齐聚物间的活泼氢转移加成反应,对所得的多嵌段聚合物做了初步的结构形态表征。 试验用单体:酚酞、4,4′-二氯二苯砜、TDL_(2,4)、MDI、低分子量聚氧化丙烯二醇N-     

“眼镜”状碘化亚铜配合物的调光和双光子发光性质

将半柔性的π-不饱和双吡啶端基配体3-pebtd与CuI分别在不同的溶剂中分层扩散, 经自组装得到8种具有Cu₂I₂L₂构型的眼镜状碘化亚铜配合物. 利用X射线单晶衍射、 X射线粉末衍射和元素分析等方法确定了配合物的结构. 对配合物的光物理性质进行了表征, 结果表明, 不同溶剂中自组装得到的配合物的单光子发光均表现出单一荧光峰, 这可归因于卤素到配体的电荷转移( ³XLCT); 并且这些配合物的发光颜色由492 到518 nm可调, 量子产率为33.1%~68.5%. 同时, 这类配合物表现出较优异的双光子发光性质, 有望将其用于生物成像领域.     

N-(1-萘基)-琥珀酰亚胺化合物晶体结构的理论预测

用Materials Studio软件对N-(1-萘基)-琥珀酰亚胺多晶粉末的X射线衍射数据进行衍射峰指标化、晶胞参数优化和空间群搜索等理论计算, 可以确定晶体结构所属的晶系和空间群, 并初步给出和多晶粉末衍射数据相近的晶胞参数; 在已确定空间群范围内, 以密度泛函理论计算得到的最低能量构象作为初始分子结构, 对N-(1-萘基)-琥珀酰亚胺多晶进行晶体结构理论预测, 给出一系列假定的晶胞参数, 从中可以找到和经上述计算给出的晶胞参数一致的晶体结构；对其进行晶胞参数优化后, 得到晶体结构具有和多晶粉末X射线衍射数据相近的衍射曲线, 并与已有的单晶数据相吻合.     

乙烯-四氟乙烯共聚物的结构表征

利用傅里叶变换红外光谱(溴化钾压片法与衰减全反射法)、X射线衍射和X射线光电子能谱法对粉末状和薄板状两种形态的乙烯-四氟乙烯共聚物(ETFE)进行了结构表征。傅里叶变换红外光谱法分析结果表明:ETFE粉末有明显的-CH2和-CF2吸收峰;X射线衍射法分析结果表明:ETFE薄板的分辨率优于ETFE粉末;X射线光电子能谱法分析结果表明:ETFE粉末与ETFE薄板的-CH2和-CF2基团含量基本一致。X射线光电子能谱分析结果显示:ETFE薄板存在有机硅类脱膜剂的污染,同时ETFE粉末存在更多吸附氧。     

Synthesis of novel fluoroalkyl end‐capped oligomers/silica gel polymer hybrids possessing antibacterial activity

New fluoroalkyl end‐capped oligomers/silica gel polymer hybrids‐low‐molecular weight biocide (hibitane) composites were prepared by the reactions of tetraethoxysilane (TEOS) with fluoroalkyl end‐capped N‐(1,1‐dimethyl‐3‐oxobutyl)acrylamide oligomer, N,N‐dimethylacrylamide oligomers, and acrylic acid oligomers in methanol under acidic conditions at room temperature. The presence of hibitane in the composites was clarified by the use of elementary analyses of nitrogen in fluorinated acrylic acid oligomer composite and thermogravimetric analysis (TGA) of these fluorinated composites. Thermal stability of fluorinated composites thus obtained were found to increase significantly compared to those of the parent fluorinated oligomers. Thermal stability of fluorinated N,N‐dimethylacrylamide oligomer, acrylic acid oligomer/silica gel polymers hybrid‐hibitane composites decreased compared to those of the corresponding fluorinated oligomers/silica gel polymer hybrids; however, the thermal stability of fluorinated N‐(1,1‐dimethyl‐3‐oxobutylacryl)amide oligomer/silica gel polymer hybrid‐hibitane composite increased significantly compared to that of the corresponding fluorinated oligomer hybrid. The sol methanol solutions of these fluorinated composites were applied to the surface modification of glass to exhibit not only a strong oleophobicity imparted by end‐capped fluoroalkyl groups in oligomers but also a good hydrophilicity on the glass surface. Fluorinated oligomers/silica gel polymer hybrids‐hibitane composites were found to exhibit high anti‐bacterial activity against Pseudomonas aeruginosa and Staphylococcus aureus. Therefore, these fluorinated hibitane composites are suggested to have high potential for new attractive functional materials through not only their excellent surface active property imparted by fluorine and their thermal stability but also through their anti‐bacterial activity. Copyright © 2005 John Wiley & Sons, Ltd.     

Complexation thermodynamics of free and graft oligomers with complementary polymers

The dilute solution complexation equilibrium between linear macromolecules and smaller complementary oligomers is considered when: (1) the oligomers are free in solution; and (2) the oligomers are covalently attached at one end to the polymer. A general statistical mechanical framework is developed and is illustrated using a simple random walk model for polymer conformation. The statistical mechanical partition functions are formulated using a generating function technique, allowing thermodynamic averages in the complexed state to be calculated. Loops, trains, and tails of all possible length are allowed in the conformation of a complexed oligomer. Simulation results for the free oligomer case are compared with those obtained for oligomers covalently attached to the polymeric molecular. The model provides a theoretical explanation for the experimentally observed enhancement of complexation of oligomers grafted to the complementary polymers.     

Isolation and identification of the linear and cyclic oligomers of poly(ethylene terephthalate) and the mechanism of cyclic oligomer formation

Chromatographic techniques are described which can be used to isolate and identify the linear and the cyclic oligomers of poly(ethylene terephthalate). Extraction of the oligomers from high molecular weight polymer produces at least eight different cyclic species, some of which are isolated and identified. The cyclic dimer, the cyclic trimer, and the cyclic tetramer of poly(ethylene terephthalate) have also been prepared by acid chloride esterification and transesterification. Similar materials can be isolated from the ethylene glycol distillate obtained from the polymer melt. The mechanism of cyclic oligomer formation has been studied by determining the rate of formation of the cyclic oligomers during polymerization and during melt extrusion of polyesters which did not initially contain cyclic oligomers. The rate of formation depends upon the concentration of hydroxyl groups; hence, the cyclic oligomers are formed by transesterification from the chain ends or cyclodepolymerization. Therefore oligomers are inevitably produced during polymerization.     

Effect of the number of monomers in the chain of an oligomer on the function of its complex formation with polydentate ligands in solutions

Simulated curves of pH-metric and spectrometric titration of homogeneous oligomers were analyzed to reveal the possibility of recognition of distinctions in the distribution diagrams of polymer and oligomer forms. Analysis of experimental data gave grounds to assume that the features of the titration curves of polyadenylic-polyuridylic ribonucleic acid are caused by cleavage of polymeric chains and formation of fairly short oligomers.     

Solid-Phase Synthesis of Phenylacetylene Oligomers Utilizing a Novel 3-Propyl-3-(benzyl-supported) Triazene Linkage

Sequence-specific phenylacetylene oligomers consisting of functionalized monomers (hexyl benzoate, hexyl phenyl ether, benzonitrile, and tert-butylphenyl) are synthesized in gram quantities using solid-phase methods. Growing oligomers are attached to a divinylbenzene cross-linked polystyrene support by the 1-aryl-3-propyl-3-(benzyl-supported) triazene moiety. This linkage is obtained by reaction of arenediazonium tetrafluoroborate salts with a n-propylamino-modified Merrifield resin. Condensation strategies are described, producing oligomers with higher yields and simplified procedures compared to solution-phase methods. Terminal acetylene is protected with a trimethylsilyl group. After deprotection of the resin-bound terminal acetylene, an aryl iodide monomer or an aryl iodide-terminated oligomer is coupled to the supported oligomer using a palladium(0) catalyst. The cycle can be repeated to produce sequence-specific oligomers of varying length and functionality. The resulting oligomers are liberated from the polymer support by cleavage of the 1-aryl-3-propyl-3-(benzyl-supported) triazene group by reaction with iodomethane producing an aryl iodide.     

Quantitative analysis of hindered amine light stabilizers by CZE with UV detection and quadrupole TOF mass spectrometric detection

The current work describes the development of a CZE method with quadrupole QTOF‐MS detection and UV detection for the quantitation of Cyasorb 3529, a common hindered amine light stabilizer (HALS), in polymer materials. Analysis of real polymer samples revealed that the oligomer composition of Cyasorb 3529 changes during processing, a fact hampering the development of a straightforward method for quantitation based on calibration with a Cyasorb 3529 standard. To overcome this obstacle in‐depth investigations of the oligomer composition of this HALS using QTOF‐MS and QTOF‐MS/MS had to be performed whereby 22 new oligomer structures, in addition to the ten structures already described, were identified. Finally, a CZE method for quantitative analysis of this HALS was developed starting with a comprehensive characterization of a Cyasorb 3529 standard using CZE‐QTOF‐MS, subsequently allowing the correct assignment of most Cyasorb 3529 oligomers in an electropherogram with UV detection. Employing the latter detection technique and hexamethyl‐melamine as internal standard, peak areas obtained for the melamine could be correlated with those from the triazine ring, the UV‐absorbing unit present in the HALS. This approach finally allowed proper quantitation of the single oligomers of Cyasorb 3529, an imperative for the quantitative assessment of this HALS in real polymer samples.     

Graft copolymers having hydrophobic backbone and hydrophilic branches. III. Synthesis of graft copolymers having oligovinylpyrrolidone as hydrophilic branch

Graft copolymers were synthesized by the esterification reaction between acrylic copolymers and carboxyl group terminated vinylpyrrolidone oligomer using phase transfer catalysts. Acrylic copolymers were obtained by the radical copolymerization of β-bromoethyl methacrylate, chloromethylstyrene or glycidyl methacrylate with methyl methacrylate. Hydrophilic oligomers were prepared by the radical oligomerization of vinylpyrrolidone using β-mercaptopropionic acid as chain transfer agent. The degree of esterification increased with decreasing the molecular weight of oligomer and with increasing the number of potential grafting sites on polymer backbones. The water dispersibility of graft copolymers increased with increasing the nitrogen content and was therefore dependent on the branch oligomer content.     

Synthesis, structure, and photophysical and electrochemical properties of a pi-stacked polymer

Dibenzofulvene (DBF) was polymerized using anionic initiators to afford a vinyl polymer. Oligo(DBF)s having from two to eight side-chain fluorene moieties bearing different chain-terminal groups were isolated by preparative size-exclusion chromatography. The structures of the isolated oligomers were revealed by single-crystal X-ray and (1)H NMR analyses. Both in solution and in crystal, the in-chain fluorene moieties stacked on top of each other, while the terminal conformation varied depending on the terminal group. These conformational characteristics were supported by molecular mechanics and dynamics calculations. The oligomers and polymers indicated hypochromism and red shift in UV absorption spectra and exclusive excimer emission in fluorescence spectra. In addition, reduced oxidation potentials were observed for the oligomers in electrochemical analyses, which suggests charge delocalization over the pi-stacked electron systems. The photophysical and electrochemical effects increased with the chain length of the oligomers and leveled off around the chain length of an oligomer consisting of five fluorene units.     

Intrachain electron transfer in conducting oligomers and polymers: the mixed valence approach

Organic mixed valence compounds consisting of bisdiarylamino charge-bearing units with an oligothiophene bridge and oligothiophene radical cations have been compared using molecular modeling. The study has been performed with oligomers of 1 to 22 thiophene units. These two series of molecules have several properties in common, and intramolecular Single Electron Transfer (SET) in both series can be described within the same theoretical framework. Conducting oligomer radical cations and slightly doped conducting polymers appear as special cases of the vast ensemble of organic mixed valence compounds. Short oligomers are class III, whereas longer oligomers and conducting polymers are class II. Therefore, doped conducting polymers cannot be correctly modeled using oligomers with a short conjugation length. Experimental evidence extracted from the literature confirms these findings. Single electron transfer theories can thus be used when studying interchain and intrachain electron transfer in slightly doped conducting polymers and in materials consisting of short oligomers. This makes it possible to extract from the UV-vis-near-IR spectra the electron-transfer constant rate along or between the pi-conjugated chain. The main differences among inorganic, organic, and conducting oligomer or polymer mixed valence compounds lies in the H(ab) and lambda values associated with these different series. Inorganic mixed valence compounds have small H(ab) and lambda values; organic mixed valence compounds have large H(ab) and lambda values, whereas conducting oligomers and polymers have large H(ab) but small lambda values. This induces charge delocalization to occur for systems larger than those of inorganic and nitrogen-centered organic mixed valence compounds.     

Structure and properties of epoxy composites cured with new organosilicon amines

The results of the curing of bisphenol A-based epoxy oligomers (ED-20 and NPEL-128) with silicon-containing amines (SCAs) synthesized by the interaction between bifunctional alcohols with different molecular masses and γ-aminopropyltriethoxysilane (AGM-9) are reported. It is shown that, in the case of using SCAs, epoxy oligomer is cured more completely and a higher degree of elasticity in the polymer matrix is achieved without using modifiers, which is impossible in the case when polyethylene polyamines are used.