High-temperature calorimetry of (La1−xLnx)PO4 solid solutions

The enthalpy increment of the monazite-type solid solutions of LaPO₄ with NdPO₄, EuPO₄ and GdPO₄ has been measured by drop calorimetry at T = 1000 K. The results show deviations (excess enthalpy) from ideal behaviour that have been interpreted in terms of lattice strains resulting from the ion size effects of substitution of La³⁺ by Ln³⁺. For (La_0.5Gd)_0.5PO₄ also the temperature dependence has been determined for T = (515 to 1565) K, indicating that the excess enthalpy decreases with increasing temperature.     

High-temperature heat capacity of zirconolite (CaZrTi2O7)

Enthalpy increment measurements in the range of (520 to 1570) K were carried out utilizing drop calorimetry on zirconolite (CaZrTi₂O₇). The high-temperature dependence of the heat capacity of zirconolite has been determined from the simultaneous analysis of our enthalpy increment measurements and published low-temperature heat capacity data.     

The heat capacities and thermodynamic functions of some derivatives of ferrocene

The heat capacities of benzoylferrocene (BOF), C₅H₅FeC₅H₄COC₆H₅, and benzylferrocene (BF), C₅H₅FeC₅H₄CH₂C₆H₅, have been measured by the low-temperature adiabatic calorimetry in the temperature range from 6 K to 372 K. The purity benzylferrocene and thermodynamic properties – the triple point temperature and the enthalpy of fusion have been obtained. The ideal gas thermodynamic functions (changes of the entropy, enthalpy, and Gibbs free energy) of BOF and BF were derived at T = 298.15 K using the heat capacities and previously determined data on the saturation vapours pressures and the enthalpies of sublimation. The ideal gas enthalpy of formation and absolute entropy of BOF at T = 298.15 K have been obtained from quantum chemical calculations, where as the thermodynamic properties of BF have been estimated by empirical method of group equations. A good agreement between experimental and theoretical values provides an additional check of the reliability of the experimental data.     

Thermodynamic properties of 4-tert-butyl-diphenyl oxide

The main thermodynamic functions (changes of the entropy, enthalpy, and Gibbs free energy) and functions of formation at T = 298.15 K of 4-tert-butyl-diphenyl oxide in condensed and ideal gas states were computed on the basis of experimental results obtained. The heat capacities of 4-tert-butyl-diphenyl oxide was measured by vacuum adiabatic calorimetry over the temperature range (8 to 371) K. The temperature, the enthalpy and the entropy of fusion were determined. The energy of combustion of the sample was determined by static-bomb combustion calorimetry. The saturation vapor pressures of the substance were measured by dynamic transpiration method over the temperature and pressure intervals (298 to 325) K and (0.05 to 1.2) Pa. The enthalpy of sublimation at T = 298.15 K was derived. The contribution of O-(2C_b) group (where C_b is the carbon atom in a benzene ring) into the absolute entropies of diphenyl oxide derivatives was assessed.     

The high-temperature heat capacity of ThPd3 and UPd3

The enthalpy increments of UPd₃ and ThPd₃ have been measured using the drop calorimetry for temperature range (480 to 1290) K. The heat capacity curves have been derived using the simultaneous linear regression of our data and the low temperature heat capacity data from previous studies. Furthermore the Schottky contributions for UPd₃ were determined by comparing the ThPd₃ and UPd₃ heat capacity functions and correlated with the theoretical values calculated from the crystal field energy levels.     

The standard thermodynamic functions of fullerene chloride,C60Cl30

The heat capacity of a crystal solvate of fullerene chloride, C₆₀Cl₃₀·0.09 Cl₂, was measured by vacuum adiabatic calorimetry in the temperature range from (25 to 371.5) K. The thermodynamic functions (changes of the enthalpy, entropy, and Gibbs free energy) of C₆₀Cl₃₀·0.09 Cl₂ have been derived. On the basis of obtained data and the enthalpy of formation of C₆₀Cl₃₀ determined before, the entropy and Gibbs free energy of formation of the fullerene chloride were calculated at T = 298.15 K.     

High-temperature calorimetry of zirconia: Heat capacity and thermodynamics of the monoclinic–tetragonal phase transition

The high-temperature heat capacity of zirconia was directly measured by differential scanning calorimetry between T = (1050 and 1700) K and derived from the heat content measured by transposed temperature drop calorimetry between T = (970 and 1770) K, including the monoclinic–tetragonal (m–t) phase transition region. The enthalpy and entropy of the m–t phase transition are (5.43 ± 0.31) kJ · mol⁻¹ and (3.69 ± 0.21) J · K⁻¹ · mol⁻¹, respectively. Values of thermodynamic functions are provided from room temperature to 2000 K.     

Enthalpy of solution of CO2 in aqueous solutions of methyldiethanolamine at T = 372.9 K and pressures up to 5 MPa

Experimental enthalpies of solution of CO₂ in aqueous solution of methyldiethanolamine (MDEA) of 15 wt% and 30 wt% are reported. The measurements were performed using a flow calorimetric technique at temperature of 372.9 K and pressures range from 0.5 MPa to 5 MPa. Gas solubilities data at same temperature and pressures were derived from the enthalpy data. Experimental enthalpies of solution are combined with available literature data in order to examine pressure and composition influences.     

Experimental and computational thermochemistry of the dihydroxypyridine isomers

The standard (p^∘ = 0.1 MPa) molar enthalpy of formation for crystalline 2,3-dihydroxypyridine was measured, at T = 298.15 K, by static bomb calorimetry and the standard molar enthalpy of sublimation, at T = 298.15 K, was obtained using Calvet microcalorimetry. These values were used to derive the standard molar enthalpy of formation of 2,3-dihydroxypyridine in gaseous phase, at T = 298.15 K, –(263.9 ± 4.6) kJ · mol⁻¹.Additionally, high-level density functional theory calculations using the B3LYP hybrid exchange-correlation energy functional with extended basis sets have been performed for all dihydroxypyridine isomers to determine the thermochemical order of stability of these systems. The agreement between experiment and theory for the 2,3-dihydroxypyridine isomer gives confidence to the estimates of the enthalpies of formation concerning the other five isomers. It is found that the enthalpic increment for the dihydroxy substitution of pyridine is equal to the sum of the respective enthalpic increment of the monosubstituted pyridines.     

Calorimetric analysis of NaF and NaLaF4

Heat flux calorimetry was used to measure the heat capacity of NaF between 630 K and 1100 K. The results agreed well with previous measurements known from the literature. Similar experiments were performed on NaLaF₄. This compound was synthesized from NaF and LaF₃ and analyzed by X-ray diffraction. The heat capacity of NaLaF₄ was determined for two temperature ranges: from 4 K to 400 K, for which adiabatic calorimetry, and from 623 K to 1213 K for which differential scanning heat flux calorimetry was used. The two heat capacity series fit smoothly; the resulting C_p,m function was used in a reassessment of the binary system (NaF + LaF₃).     

Experimental and computational thermodynamic study of ortho-, meta-, and para-methylbenzamide

The Knudsen mass-loss effusion technique was used to measure the vapour pressures of the three crystalline isomers of methylbenzamide. From the temperature dependence of the vapour pressures, the standard molar enthalpies of sublimation and the enthalpies of the intermolecular hydrogen bonds N−H⋯O were calculated. The temperature and molar enthalpy of fusion of the studied isomers were measured using differential scanning calorimetry. The values of the standard (p^° = 0.1 MPa) molar enthalpy of formation in the crystalline phase, at T = 298.15 K, of the compounds studied were derived from their standard massic energies of combustion measured by static-bomb combustion calorimetry. From the experimental values, the standard molar enthalpies of formation in the gaseous phase, at T = 298.15 K, were calculated and compared with the values estimated by employing computational calculations that were conducted using different quantum chemical methods: G3(MP2), G3, and CBS-QB3. Good agreement between experimental and theoretical results is verified. The aromaticity of the compounds has been evaluated through nucleus independent chemical shifts (NICS) calculations.     

The standard state thermodynamic properties for completely ionized hydrochloric acid and ionization of water up to 523 K

In this communication we report calorimetric data for the standard state enthalpies of solution of α-Ba(OH)₂ in high dilution (10^?3 m) hydrochloric acid obtained from integral heats of solution measurements from temperatures of (333.55 to 516.64) K and extrapolated to 298.15 K. From previous studies in this laboratory on BaCl₂(aq) and auxiliary literature data, the standard state thermodynamic functions for completely ionized HCl(aq) can be determined. These new data are in good agreement and confirm our previously reported results on HCl(aq) from ionic additivity. The enthalpy of formation of solid α-Ba(OH)₂ at temperature of 298.15 K of ?939.38 kJ · mol^?1 can also be calculated from the present results. Values of the standard state heat capacity change for the ionization of water up to temperature of 523.15 K and at p_sat were calculated from present results using the literature data for NaOH(aq) and NaCl(aq) obtained from high dilution calorimetric measurements.     

Molecular energetics of 4-methyldibenzothiophene: An experimental study

The standard ($p^{°}=0.1\text{MPa}$) molar enthalpy of formation of 4-methyldibenzothiophene, in the gaseous phase, at T = 298.15 K, was derived from the combination of the values of the standard molar enthalpy of formation, in the crystalline phase, at T = 298.15 K, and the standard molar enthalpy of sublimation, at the same temperature. The standard molar enthalpy of formation in the crystalline phase, determined from the standard massic energy of combustion, in oxygen, is (70.9 ± 4.8) kJ · mol^?1 and was measured by rotating-bomb combustion calorimetry. From Calvet microcalorimetry measurements, the standard molar enthalpy of sublimation obtained is (90.3 ± 0.7) kJ · mol^?1.     

Calorimetric and computational study of 7-hydroxycoumarin

The standard (p° = 0.1 MPa) molar energy of combustion in oxygen, at T = 298.15 K, of 7-hydroxycoumarin was measured by static bomb calorimetry. The value of the standard molar enthalpy of sublimation was obtained by Calvet microcalorimetry and corrected to T = 298.15 K. Combining these results, the standard molar enthalpy of formation of the compound, in the gas phase, at T = 298.15 K, has been calculated, ?(337.5 ± 2.3) kJ · mol^?1. The values for the temperature of fusion, T_fusion, and for the fusion enthalpy, at T = T_fusion, are also reported.Additionally, high-level density functional theory calculations using the B3LYP hybrid exchange-correlation energy functional with extended basis sets, the MC3BB and MC3MPW methods and more accurate correlated computational techniques of the MCCM suite have been performed for the compound.The agreement between experiment and theory gives confidence to estimate the enthalpy of formation of the remaining hydroxycoumarins substituted in the benzene ring.     

Calorimetric measurements and first principles to study the (Ag-Li) liquid system

Integral molar enthalpies of mixing were determined by drop calorimetry for (Ag-Li) liquid alloys at two temperatures (1253 and 873) K. The integral molar enthalpies of mixing are negative in the entire range of concentrations. For the mole fraction of lithium X_Li = 0.5664, minimum value of the integral enthalpy of mixing of at ΔH_m = −11.679 kJ/mol was observed. For (Ag-Li) liquid alloys, between T = (873 and 1253) K no temperature dependence was observed. Ab initio molecular dynamics was used to simulate liquid phase structures at T = 873 K (Li-rich side) and at T = 1250 K (Ag-rich phase) for subsequent calculation of the vibrational energy, respectively. Our measured and calculated data were compared with literature data.     

Thermal properties of [Cr(NH3)6](BF4)3 studied by adiabatic and relaxation calorimetry

Four (solid–solid) phase transitions were detected in the temperature range of (9 to 300) K in polycrystalline [Cr(NH₃)₆](BF₄)₃ at T_C1 = 240.7 K, T_C2 = 108.0 K, T_C3 = 91.9 K, and T_C4 = 61.3 K by adiabatic calorimetry. The measurements by relaxation calorimetry were followed on lowering temperature from 20 K down to 0.35 K under six different external magnetic field values (9, 7, 5, 3, 1 and 0) T. For non-zero values of applied magnetic field well-defined Schottky anomaly appears. Magnetic heat capacity was calculated assuming the zero-field splitting for the decoupled Cr(III) ions. There is no discrepancy between the observed and calculated values. Isothermal magnetization curve recorded up to 5 T was measured at temperature of 1.8 K.     

The reactivity of delithiated Li(Ni1/3Co1/3Mn1/3)O2, Li(Ni0.8Co0.15Al0.05)O2 or LiCoO2 with non-aqueous electrolyte

The high temperature reactions of 1 M LiPF₆ EC:DEC and LiCoO₂, Li(Ni_1/3Co_1/3Mn_1/3)O₂ (NCM) or Li(Ni_0.8Co_0.15Al_0.05)O₂ (NCA) charged to 4.2 V and 4.4 V, respectively, were studied by accelerating rate calorimetry (ARC). The results indicate that NCM shows better thermal stability than both LiCoO₂ and NCA. The state-of-the-art NCA sample shows better safety properties than LiCoO₂. The reactivity of the samples depends on the electrolyte:active material ratio used during ARC testing. Electrode materials charged to 4.4 V are more reactive than the electrode materials charged to 4.2 V. These results should be useful for Li-ion battery researchers interested in maximizing the safety of high energy density cells and also as a benchmark for other researchers using ARC.     

Vibrational spectra,conformational equilibria,ab initio calculations and vibrational assignments of ethylmethylfluorosilane

The infrared spectra of ethylmethylfluorosilane (CH₃SiHFCH₂CH₃) have been recorded as a vapour, liquid and solid at 78 K in the 4000–50 cm⁻¹ range and isolated in an argon matrix at ca. 5 K. Infrared spectra of two different solid phases were obtained after annealing to temperatures of 120 and 130 K, and recooling to 78 K. Although the IR spectra were quite similar in the MIR region, certain differences were noted in the FIR region below 400 cm⁻¹. The most stable conformer MeMe was present after annealing to 130 K, but three bands belonging to MeH were detected after annealing to 120 K. Various infrared bands changed intensity when the argon matrix was annealed to temperatures between 20 and 35 K, and some of these were related to changes in the conformational abundance.Raman spectra of the liquid were recorded at room temperature and at various temperatures between 295 and 153 K. Spectra of an amorphous and annealed solid were recorded at 78 K. In the variable temperature Raman spectra, various bands changed in intensity and were interpreted in terms of conformational equilibria between the three possible conformers. Complete assignments were made for all the bands of the most stable conformer MeMe. From various bands assigned to the three conformers, the conformational enthalpy difference ΔH from MeMe to the intermediate energy conformer MeH was found to be 0.5 kJ mol⁻¹ and to the highest conformer MeF was 0.7 kJ mol⁻¹. At ambient temperature this leads to 39% MeMe, 32% MeH and 29% of the MeF conformer in the liquid.Ab initio calculations in the RHF, MP2, DFT approximations and very accurate G2 calculations were carried out. With one exception, the MeMe conformer had the lowest enthalpy in all these calculations, the MeH had the intermediate and the MeF the highest enthalpy, and the calculations were in good agreement with the measurements.     

Vapour pressure of diethyl phthalate

Measurements of vapour pressure in the liquid phase and of enthalpy of vaporisation and results of calculation of ideal-gas properties for diethyl phthalate are reported. The method of comparative ebulliometry, the static method, and the Knudsen mass-loss effusion method were employed to determine the vapour pressure. A Calvet-type differential microcalorimeter was used to measure the enthalpy of vaporisation. Simultaneous correlation of vapour pressure, of enthalpy of vaporisation and of difference in heat capacities of ideal gas and liquid/solid phases was used to generate parameters of the Cox equation that cover both the (vapour + solid) equilibrium (approximate temperature range from 220 K to 270 K) and (vapour + liquid) equilibrium (from 270 K to 520 K). Vapour pressure and enthalpy of vaporisation derived from the fit are reported at the triple-point temperature T = 269.92 K (p = 0.0029 Pa, Δ_vapH_m = 85.10 kJ · mol⁻¹ ), at T = 298.15 K (p = 0.099 Pa, Δ_vapH_m = 82.09 kJ · mol⁻¹), and at the normal boiling temperature T = 570.50 K (Δ_vapH_m = 56.49 kJ · mol⁻¹). Measured vapour pressures and measured and calculated enthalpies of vaporisation are compared with literature data.     

Heat capacity and thermodynamic properties of germanium disulfide at temperatures from T = (2 to 1240) K

The heat capacity of polycrystalline germanium disulfide α-GeS₂ has been measured by relaxation calorimetry, adiabatic calorimetry, DSC and heat flux calorimetry from T = (2 to 1240) K. Values of the molar heat capacity, standard molar entropy and standard molar enthalpy are 66.191 J · K^?1 · mol^?1, 87.935 J · K^?1 · mol^?1 and 12.642 kJ · mol^?1. The temperature of fusion and its enthalpy change are 1116 K and 23 kJ · mol^?1, respectively. The thermodynamic functions of α-GeS₂ were calculated over the range (0 ? T/K ? 1250).