Physio-chemical influence of high electron-phonon coupling induced by 120 MeV Ag9+ SHI irradiation on exfoliated MoS2 - PVA nanocomposite films for achieving remarkable electrical conductivity for potential application in organic electronics

Swift heavy ion (SHI) irradiation technology is known to enhance the optical, electronic, mechanical, and electrical properties in polymer nanocomposites by the virtue of electron-phonon coupling. In the present work, Molybdenum disulphide (MoS₂), a two-dimensional metal dichalcogenide, has been exfoliated via liquid-phase exfoliation using N-methyl-2- pyrrolidone (NMP) as the solvent that yielded nanosheets of around 2–4 layers as depicted by HR-TEM images. MoS₂ - PVA free-standing films were prepared by wet chemical technique i.e. solution casting method and irradiated by focussed high-energy Ag⁹⁺ ion beam at fluence range of 1E10 - 3E11 ions/cm². As a consequence, the structural modification was observed by X-Ray diffraction studies that showed the shift of (002) plane of MoS₂ while Raman studies indicated the decrease of degree of disorderness at fluence 1E10 ions/cm². SHI irradiation has found to induce a two-order increase in the electrical conductivity yielding a 9.7 E-3 S/cm against that of the pristine films at 2.6E-5 S/cm. The enhanced conductivity is attributed to the induced dispersion and annealing of MoS₂ nanosheets in the PVA matrix due to the interaction of 120 MeV Ag⁹⁺ ion beam irradiation as explained by Thermal spike model.     

MoS2 Nanosheets Supported on 3D Graphene Aerogel as a Highly Efficient Catalyst for Hydrogen Evolution

The development of efficient catalysts for electrochemical hydrogen evolution is essential for energy conversion technologies. Molybdenum disulfide (MoS₂) has emerged as a promising electrocatalyst for hydrogen evolution reaction, and its performance greatly depends on its exposed edge sites and conductivity. Layered MoS₂ nanosheets supported on a 3D graphene aerogel network (GA‐MoS₂) exhibit significant catalytic activity in hydrogen evolution. The GA‐MoS₂ composite displays a unique 3D architecture with large active surface areas, leading to high catalytic performance with low overpotential, high current density, and good stability.     

Dynamic mechanical and dielectrical properties of poly(vinyl alcohol) and poly(vinyl alcohol)‐based nanocomposites

In this article we report on the investigation of the dynamics of poly(vinyl alcohol) (PVA) and PVA‐based composite films by means of dielectric spectroscopy and dynamic mechanical thermal analysis. Once the characterization of pure PVA was done, we studied the effect of a nanostructured magnetic filler (nanosized CoFe₂O₄ particles homogeneously dispersed within a sulfonated polystyrene matrix) on the dynamics of PVA. Our results suggest that the α‐relaxation process, corresponding to the glass transition of PVA, is affected by the filler. The glass‐transition temperature of PVA increases with filler content up to compositions of around 10 wt %, probably as a result of polymer–filler interactions that reduce the polymer chain mobility. For filler contents higher than 10 wt %, the glass‐transition temperature of PVA decreases as a result of the absorption of water that causes a plasticizing effect. The β‐ and γ‐relaxation processes of PVA are not affected by the filler as stated from both dynamic mechanical thermal analysis and dielectric spectroscopy. Nevertheless, both relaxation processes are greatly affected by the moisture content. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1968–1975, 2001     

Free‐standing and Flexible MoS2/rGO Paper Electrode for Amperometric Detection of Folic Acid

The development of flexible electrodes is of considerable current interest because of the increasing demand for modern electronics, portable medical products, and compact devices. We report a new type of flexible electrochemical sensor fabricated by integrating graphene and MoS₂ nanosheets. A highly flexible and free‐standing conductive MoS₂ nanosheets/reduced graphene oxide (MoS₂/rGO) paper was prepared by a two‐step process: vacuum filtration and chemical reduction treatment. The MoS₂/graphene oxide (MoS₂/GO) paper obtained by a simple filtration method was transformed into MoS₂/rGO paper after a chemical reduction process. The obtained MoS₂/rGO paper was characterized by scanning electron microscopy, X‐ray diffraction spectroscopy, X‐ray photoelectron spectroscopy, Raman spectroscopy, electrochemical impedance spectroscopy. The electrochemical behavior of folic acid (FA) on MoS₂/rGO paper electrode was investigated by cyclic voltammetry and amperometry. Electrochemical experiments indicated that flexible MoS₂/rGO composite paper electrode exhibited excellent electrocatalytic activity toward the FA, which can be attributed to excellent electrical conductivity and high specific surface area of the MoS₂/rGO paper. The resulting biosensor showed highly sensitive amperometric response to FA with a wide linear range.     

利用光热电效应收集近红外光能的二硫化钼和热释电高分子纳米复合物

设计合成了一种基于二硫化钼（MoS₂）/热释电聚合物的柔性薄膜光热电纳米发电机（PTENG）。过渡金属硫族化合物作为薄层纳米薄片,可以捕获近红外（NIR）光,并将其转化为热能。同时,热释电聚合物将无机纳米片所收集的热能转化为电能。在近红外辐照下,PTENG可以瞬间产生电压和光电流,且输出长期保持在较高水平。通过光热效应与热释电效应的有效耦合,该体系具有较高的热电转换系数。我们还通过理论模拟分析了MoS₂在聚合物纳米复合材料中的作用。MoS₂的存在显著提高了热释电聚合物薄膜的温度变化率,提高了器件的光电响应。     

Direct borohydride fuel cell performance using hydroxide-conducting polymeric nanocomposite electrolytes

Solid electrolyte membranes based on alkali-doped polyvinyl alcohol (PVA) and PVA/carbon nanotubes (PVA/CNTs) are used in direct borohydride fuel cells (DBFCs). As 0.05 wt % of CNT is incorporated into the PVA matrix, the polymer crystallinity is decreased from 42.4% to 38.0% and the fractional free volume increases from 2.48% to 3.53%. The KOH-doped PVA/CNT exhibits the highest ionic conductivity of 0.0805 S cm⁻¹, because of the increased polymer free volume (which promotes vehicular OH⁻ transport) and the presence of CNT (which serves as the conducting microchannels). Sodium borohydride (NaBH₄) in NaOH solution and potassium borohydride (KBH₄) in KOH mixture are fed into the cells. The power density of the KBH₄-based DBFC is almost twice that of the NaBH₄-based DBFC (184 vs. 92 mW cm⁻²) due to less KBH₄ permeability through the films, higher conductivity of the KOH-doped PVA composites than those in the sodium counterpart, and probably higher electro-catalytic kinetics. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013, 51, 1779–1789, 2013     

Solution‐Processed Two‐Dimensional MoS2 Nanosheets: Preparation,Hybridization, and Applications

As one member of the emerging class of ultrathin two‐dimensional (2D) transition‐metal dichalcogenide (TMD) nanomaterials, the ultra‐thin MoS₂ nanosheet has attracted increasing research interest as a result of its unique structure and fascinating properties. Solution‐phase methods are promising for the scalable production, functionalization, hybridization of MoS₂ nanosheets, thus enabling the widespread exploration of MoS₂‐based nanomaterials for various promising applications. In this Review, an overview of the recent progress of solution‐processed MoS₂ nanosheets is presented, with the emphasis on their synthetic strategies, functionalization, hybridization, properties, and applications. Finally, the challenges and opportunities in this research area will be proposed.     

Incorporation of two‐dimensional nanomaterials into silk fibroin nanofibers for cardiac tissue engineering

Mimicking the extracellular matrix to have a similar nanofibrous structure regarding electrical conductivity and mechanical properties would be highly beneficial for cardiac tissue engineering. The molybdenum disulfide, MoS₂, and reduced graphene oxide, rGO, nanosheets are two‐dimensional nanomaterials which can be considered as great candidates for enhancing the electrical and mechanical properties of biological scaffolds for cardiac tissue engineering applications. In this study, MoS₂ and rGO nanosheets were synthesized and incorporated into silk fibroin nanofibers, SF, via electrospinning method. Then, the human iPSCs transfected with TBX‐18 gene, TBX18‐hiPSCs, were seeded on these scaffolds for in vitro studies. The MoS₂ and rGO nanosheets were studied by Raman spectroscopy. After incorporation of the nanosheets into SF nanofibers, the associated characterizations were carried out including scanning electron microscopy, transmission electron microscopy, water contact angle, and mechanical test. Furthermore, SF, SF/MoS₂, and SF/rGO scaffolds were used for in vitro studies. Herein, the scaffolds exhibited acceptable biocompatibility and considerable attachment to TBX18‐hiPSCs confirmed by 3‐(4, 5‐dimethylthiazol‐2‐yl)‐2, 5‐diphenyl tetrazolium bromide, MTT, assay, and scanning electron microscopy. Also, the real‐time PCR and immunostaining studies confirmed the maturity and upregulation of cardiac functional genes, including GATA‐4, c‐TnT, and α‐MHC in the SF/MoS₂ and SF/rGO scaffolds compared with the bare SF one. Therefore, the reinforcement of these SF‐based scaffolds with MoS₂ and rGO endues them as a suitable candidate for cardiac tissue engineering.     

Synthesis of MXene-supported layered MoS2 with enhanced electrochemical performance for Mg batteries

In this paper, the petal-like MoS₂/MXene composite has been successfully synthesized by one-step hydrothermal method. With the combination of few-layer MoS₂ nanosheets and the high conductive MXene substrate, the composite exhibits enhanced capacities and rate performance as cathode material of Mg batteries.     

Spherical filler-promoting thermally conductive pathway in graphite-containing polymer composites for high heat radiation

Graphite is an efficient and affordable filler for polymer composites, allowing the control of thermal conductivity. In comparison to other thermally conductive fillers, graphite is lightweight and flexible but affords anisotropic thermal conductivity. Herein, the control of thermal conductivity of graphite-containing polymer composite sheet using spherical polymer particles as additional fillers is described. The thermal conductivity in the through-plane direction (λ_t) of the composite sheet is enhanced by varying the composition ratio of the two fillers (flaky graphite and spherical particles), and optimizing the forming temperature and pressure. Graphite-containing (25 wt%) polymer composite sheet formed by compression at 150 °C and 10 MPa exhibits λ _t value of 0.66 W/m K. Upon mixing of polystyrene microspheres, λ _t is successfully increased. The maximum value of thermal conductivity for a composite sheet with 35 wt% of graphite and 50 wt% of spherical particles is 7.51 W/m K, at 180 °C and 10 MPa. The graphite-containing polymer matrix forms a sequentially connected network-like structure in the composite sheet. Excess polymer microspheres lead to the formation of void structures inside the composite sheet, reducing the thermal conductivity. Thermo-camera observations proved that the composite sheets with higher λ _t value showed comparably high heat radiations. © 2020 Wiley Periodicals, Inc. J. Polym. Sci. 2020 , 58, 607–615     

Combining Nitrogen‐Doped Graphene Sheets and MoS2: A Unique Film–Foam–Film Structure for Enhanced Lithium Storage

With a notable advantage in terms of capacity, molybdenum disulfide has been considered a promising anode material for building high‐energy‐density lithium‐ion batteries. However, its intrinsically low electronic conductivity and unstable electrochemistry lead to poor cycling stability and inferior rate performance. We herein describe the scalable assembly of free‐standing MoS₂–graphene composite films consisting of nitrogen‐doped graphene and ultrathin honeycomb‐like MoS₂ nanosheets. The composite has a unique film–foam–film hierarchical top‐down architecture from the macroscopic to the microscopic and the nanoscopic scale, which helps rendering the composite material highly compact and leads to rapid ionic/electronic access to the active material, while also accommodating the volume variation of the sulfide upon intercalation/deintercalation of Li. The unique structural merits of the composite lead to enhanced lithium storage.     

Mussel‐inspired decoration of Ni(OH)2 nanosheets on 2D MoS2 towards enhancing thermal and flame retardancy properties of poly(lactic acid)

In the present work, a facile and environmental method was developed to fabricate the novel functionalized MoS₂ hybrid. Firstly, MoS₂ nanosheets were coated with polydopamine (PDA) through the self‐polymerization of dopamine (MoS₂‐PDA) in a buffer solution. Then the decoration of Ni(OH)₂ on the MoS₂‐PDA was synthesized because of the strong affinity of Ni²⁺ with hydroxyl groups in PDA. Finally, the as‐synthesized MoS₂‐PDA@Ni(OH)₂ was introduced into poly(lactic acid) (PLA) matrix to explore flame retardancy, thermal stability, and crystalline property of the composites. As confirmed by X‐ray diffraction (XRD), Fourier‐transform infrared spectrometer (FTIR), transmission electron microscopy (TEM), scanning electron microscopy (SEM), and thermogravimetric analysis (TGA), the MoS₂ nanosheets were dually modified with PDA and Ni(OH)₂ without destroying the original structures. The thermal degradation of PLA with MoS₂‐PDA@Ni(OH)₂ generated a notably higher yield of char. Moreover, the crystallization rate of composites is higher than neat PLA. The cone calorimeter test revealed that the introduction of 3% MoS₂‐PDA@Ni(OH)₂ resulted in lower Peak Heat Release Rate (PHRR) (decreased by 21.7%). Thus, the research provided an innovative functionalization method for manufacturing PLA composites with high performances.     

Enhanced Photocatalytic Hydrogen Evolution over Hierarchical Composites of ZnIn2S4 Nanosheets Grown on MoS2 Slices

A highly active hierarchical MoS₂/ZnIn₂S₄ composite catalyst was synthesized in situ by using a facile controlled‐growth approach through a solvothermal process. During the solvothermal reaction, 2D ultrathin curled ZnIn₂S₄ nanosheets grew on the surface of MoS₂ slices, which could help to form a more‐homogeneous mixture, effective interfacial contact, and strong interactions between the ZnIn₂S₄ nanosheets and the MoS₂ slices. The intimate contact between ZnIn₂S₄ and MoS₂ favored the formation of junctions between the two components, thereby improving the charge separation and prolonging the mean lifetime of the electron–hole pairs. Moreover, growing ZnIn₂S₄ nanosheets by visible‐light catalysis on MoS₂ slices afforded a higher number of available catalytically active sites. So, the photocatalytic hydrogen‐evolution performance of the hierarchical MoS₂/ZnIn₂S₄ composite was significantly enhanced, owing to a synergistic effect of these factors. This work could provide new insights into the fabrication of a highly efficient and low‐cost non‐noble‐metal co‐catalyst for visible‐light H₂ generation.     

Ultrathin MoS2 Nanosheets Supported on N‐doped Carbon Nanoboxes with Enhanced Lithium Storage and Electrocatalytic Properties

Molybdenum disulfide (MoS₂) has received considerable interest for electrochemical energy storage and conversion. In this work, we have designed and synthesized a unique hybrid hollow structure by growing ultrathin MoS₂ nanosheets on N‐doped carbon shells (denoted as C@MoS₂ nanoboxes). The N‐doped carbon shells can greatly improve the conductivity of the hybrid structure and effectively prevent the aggregation of MoS₂ nanosheets. The ultrathin MoS₂ nanosheets could provide more active sites for electrochemical reactions. When evaluated as an anode material for lithium‐ion batteries, these C@MoS₂ nanoboxes show high specific capacity of around 1000 mAh g^?1, excellent cycling stability up to 200 cycles, and superior rate performance. Moreover, they also show enhanced electrocatalytic activity for the electrochemical hydrogen evolution.     

Influence of the surface chemistry on the structural and mechanical properties of silica‐polymer composites

Poly(vinyl alcohol) (PVA) composite films filled with nanometric, monodisperse, and spherical silica particles were prepared by the mixing of an aqueous PVA solution and SiO₂ colloidal suspension and the evaporation of the solvent. Adjusting the solution pH to 5 and 9 controlled the PVA‐SiO₂ interaction. Adsorption isotherms showed a higher PVA/surface affinity at a lower pH. This interaction influenced the composite structure and the particle distribution within the polymer matrix, which was investigated by small‐angle neutron scattering, electron microscopy, and swelling measurements. Most of the mechanical properties could be related to the composite structure, that is, the distribution of clusters within the polymer matrix. The progressive creation of a cluster network within the polymeric matrix as the silica volume fraction increased reduced the extensibility or swelling capacity of the composite. The effect was more acute at a higher pH, at which the surface interaction with PVA was weaker and promoted the interconnection between clusters. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 3127–3138, 2003     

Effect of nano‐modified SiO2/Al2O3 mixed‐matrix micro‐composite fillers on thermal,mechanical, and tribological properties of epoxy polymers

Thermo‐mechanically durable industrial polymer nanocomposites have great demand as structural components. In this work, highly competent filler design is processed via nano‐modified of micronic SiO₂/Al₂O₃ particulate ceramics and studied its influence on the rheology, glass transition temperature, composite microstructure, thermal conductivity, mechanical strength, micro hardness, and tribology properties. Composites were fabricated with different proportions of nano‐modified micro‐composite fillers in epoxy matrix at as much possible filler loadings. Results revealed that nano‐modified SiO₂/Al₂O₃ micro‐composite fillers enhanced inter‐particle network and offer benefits like homogeneous microstructures and increased thermal conductivity. Epoxy composites attained thermal conductivity of 0.8 W/mK at 46% filler loading. Mechanical strength and bulk hardness were reached to higher values on the incorporation of nano‐modified fillers. Tribology study revealed an increased specific wear rate and decreased friction coefficient in such fillers. The study is significant in a way that the design of nano‐modified mixed‐matrix micro‐composite fillers are effective where a high loading is much easier, which is critical for achieving desired thermal and mechanical properties for any engineering applications. Copyright © 2016 John Wiley & Sons, Ltd.     

Preparation of MoS2‐graphene Hybrid Nanosheets and Simultaneously Electrochemical Determination of Levodopa and Uric Acid

MoS₂ nanoflakes were prepared by exfoliating commercial MoS₂ powders with the assistance of ultrasound and graphene foam was synthesized by chemical vapor deposition using nickel foam as the template. MoS₂‐graphene hybrid nanosheets were developed through the combination of MoS₂ nanoflakes and graphene nanosheets by ultrasonic dispersion. The hybrid nanosheets were sprayed onto the ITO coated glass, which acts as an electrode for the simultaneously electrochemical determination of levodopa and uric acid. The MoS₂‐graphene hybrid nanosheets were characterized by scanning electron microscopy, X‐ray diffraction and Raman spectroscopy. The results show that the hybrid nanosheets are composed of MoS₂ and graphene with a sheet‐like morphology. The sensitivity of the electrode for levodopa and uric acid is 0.36 μA μM⁻¹ and 0.39 μA μM⁻¹, respectively. The electrode also shows low limit of detection, good selectivity, reproducibility and stability. And it is potential for use in clinical research.     

CoFe2O4 with MoS2-xOy Nanosheets as a Co-catalyst for Enhanced Activation of Peroxydisulfate in Advanced Oxidation Processes

The application of advanced oxidation processes (AOPs) based on sulfate radicals for degrading persistent organic pollutants faces challenges due to the inefficient activation of peroxydisulfate (PDS) oxidant. Herein, a composite CoFe₂O₄/MoS_2-xO_y (CFM) catalyst consisting of CoFe₂O₄ nanoparticles uniformly dispersed on the nanosheets of oxygen-incorporated MoS₂ (MoS_2-xO_y) with flower-like morphology are fabricated through a facile two-step hydrothermal method, which results in the enhanced activation of PDS and a highly efficient degradation of phenolic pollutants. The oxygen-doping in MoS_2-xO_y leads to unsaturated sulfur and active sites on the surface of MoS₂ for accelerating the rate limiting step of Fe^III/Fe^II reduction cycle in PDS-CFM reaction. Aiming at the refractory organic pollutants in actual coking wastewater, CFM co-catalyst is introduced into a hydrogel made up of polyvinyl alcohol (PVA) and coal-tar pitch oxides (PO) to construct a multifunctional CFM@PO/PVA hydrogel. Upon hybrid CFM@PO/PVA, the coupling of the enhanced AOP with solar-driven interfacial vapor generation (SIVG) technology contributes to the degradation efficiency, the removal rate of phenol in solution and the total organic carbon in coking wastewater can reach 98 % and 91 %, respectively. The integration of heterogeneous AOPs with SIVG system provides a feasible strategy for the eco-friendly efficient purification of industrial wastewater.     

Selective modification of two-dimensional MoS2 nanosheets by polymer grafting

We reported on the direct creation of polymer brushes on two-dimensional molybdenum disulfide via the formation of C-S bond by UV-induced photopolymerization. The functionalization can be manipulated in forming polymer grafts on one side or both sides of the nanosheets.     

Synthesis of polymethacrylate‐bearing benzocyclobutene structure and extension to networked polymer based on thermal isomerization

1‐Benzocyclobutenyl methacrylate‐bearing methacrylate (BCBMA) backbone has been synthesized, and radical polymerization of the monomer was performed by utilizing 2, 2′‐azobisisobutyronitrile (AIBN) as initiator to result poly‐BCBMA. Differential scanning calorimetry (DSC) measurement of the derived poly‐BCBMA revealed the lowering of thermal isomerization temperature from that of nonsubstituted benzocyclobutene. The thermal decomposition temperature of BCBMA before and after thermal treatment was confirmed by thermogravimetric analysis (TGA). The results of the TGA observation did not show significant difference in both 5% and 10% weight loss temperature (T_d5 and T_d10). This result suggests that the thermal conversion of the poly‐BCBMA to the networked polymer take place without thermal decomposition of the main chain based on the methacrylate framework. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 2175–2180