The hydrogenation of methyl on metallic surfaces

The stream technique was used to comparatively analyze the characteristics of the deposition of a-C:H films from methyl radicals transferred by a carrier gas CH₄/C₂H _y /H₂ (y = 2, 4, 6) in a quartz tube with cylindrical insets made of Cu, Ni, Fe, W, Si, and stainless steel (SS), initial and coated with thin Pd or Rh films, over the temperature range 300–1000 K. The deposition of methyl was fully suppressed in a tube section heated to 380–800 K with all the insets specified. During further mixture movement outside this section in the tube with a decreasing wall temperature, carbon deposition resumed. The most effective catalyst of the hydrogenation reaction was stainless steel. Radicals and unsaturated hydrocarbons capable of polymerization at 300–400 K were fully removed from the carrier gas flow (CH₄/C₂H _y /H₂) after several hundreds of collisions with the surface of SS heated to 420–470 K. The possibility of creating an SS recombination filter for hydrocarbon radicals (the performance of radical hydrogenation reactions) transferred by a CH₄/C₂H _y /H₂ laminar flow was demonstrated. The deposition of a thin Pd film (∼10 nm) on steel did not increase the effectiveness of the surface with respect to radical recombination reactions. At the same time, Rh films increased the catalytic effectiveness of the surface of SS with respect to the hydrogenation of methyl and unsaturated hydrocarbons (380–420 K). The data obtained were used to select temperature conditions and mutual arrangement for the construction elements of an ITER diverter made of tungsten and stainless steel.     

Polymeric ionic liquid modified stainless steel wire as a novel fiber for solid‐phase microextraction

A polymeric ionic liquid modified stainless steel wire for solid‐phase microextraction was reported. Mercaptopropyl‐functionalized stainless steel wire that was formed by co‐condensation of tetramethoxysilane and 3‐mercaptopropyltrimethoxysilane via a sol‐gel process, which is followed by in situ surface radical chain‐transfer polymerization of 1‐vinyl‐3‐octylimidazolium hexafluorophosphate to result in polymeric ionic liquid modified stainless steel wire. The fiber surface was characterized by field emission scanning electron microscope equipped with energy dispersive X‐ray analysis. Coupled with GC, extraction performance of the fiber was tested with phenols and polycyclic aromatic hydrocarbons as model analytes. Effects of extraction and desorption conditions were investigated systematically in our work. RSDs for single‐fiber repeatability and fiber‐to‐fiber reproducibility were less than 7.34 and 16.82%, respectively. The calibration curves were linear in a wide range for all analytes and the detection limits were in the range of 10–60 ng L^?1. Two real water samples from the Yellow River and local waterworks were applied to test the as‐established solid‐phase microextraction–GC method with the recoveries of samples spiked at 10 μg L^?1 ranged from 83.35 to 119.24%. The fiber not only exhibited excellent extraction efficiency, but also very good rigidity, stability and durability.     

Liquid-phase oxidation of toluene to benzaldehyde with molecular oxygen catalyzed by copper nanoparticles supported on graphene

Highly-dispersed copper nanoparticles (Cu NPs) were fabricated on the surface of reduced graphene oxide via direct hydrazine hydrate reduction of Cu²⁺ in aqueous solution. Scanning electron microscope and transmission electron microscope images show that the Cu NPs are distributed on the surface of graphene nanosheets, and the average particle size was about 40 nm. The Cu NPs supported on graphene have high reaction activity for the oxidation of toluene to corresponding benzaldehyde. It was found that the selectivity reached 66.5% and the conversion of toluene reached 11.5%.     

A biofilm resistance surface yielded by grafting of antimicrobial peptides on stainless steel surface

Anti‐biofilm formation on the surface is a severe issue in medical implants, hull surface, and food industry. Antimicrobial peptide, magainin II, was covalently bound to stainless steel surfaces through multi‐step modification. The untreated and modified samples were analyzed by SEM‐EDS, XPS, and contact angle, respectively, which indicated the peptide was immobilized on the surfaces. The antimicrobial tests of modified samples were conducted using Staphylococcus aureus and Escherichia coli, and the results revealed that peptide modified surface decreased the biofilm and bacteria quantity of stainless steel surface.     

Biomimetic anchors for antifouling and antibacterial polymer brushes on stainless steel

Barnacle cement (BC) was beneficially applied on stainless steel (SS) to serve as the initiator anchor for surface-initiated polymerization. The amine and hydroxyl moieties of barnacle cement reacted with 2-bromoisobutyryl bromide to provide the alkyl halide initiator for the surface-initiated atom transfer radical polymerization (ATRP) of 2-hydroxyethyl methacrylate (HEMA). The hydroxyl groups of HEMA polymer (PHEMA) were then converted to carboxyl groups for coupling of chitosan (CS) to impart the SS surface with both antifouling and antibacterial properties. The surface-functionalized SS reduced bovine serum albumin adsorption, bacterial adhesion, and exhibited antibacterial efficacy against Escherichia coli (E. coli). The effectiveness of barnacle cement as an initiator anchor was compared to that of dopamine, a marine mussel inspired biomimetic anchor previously used in surface-initiated polymerization. The results indicate that the barnacle cement is a stable and effective anchor for functional surface coatings and polymer brushes.     

High temperature oxidation resistance and corrosion properties of dip coated silica coating by sol gel method on stainless steel

Silica coating for the protection of stainless steel (SS) surfaces was prepared using tetraethoxysilane and methyltriethoxysilane as precursors via an acid-catalysed (H₂SO₄) sol?Cgel method and was deposited on ferritic SS AISI 430 by dip coating. The surface morphology was studied using a scanning electron microscope equipped with energy-dispersive X-ray, phase analysis was carried out by X-ray diffraction, and isothermal oxidation was carried out at 800?°C for 200?h. Corrosion properties were examined by electrochemical impedance spectroscopy and resistance polarization methods in an aqueous medium containing 3.5?wt?% NaCl. The results indicated that silica coating improved high-temperature oxidation resistance of AISI 430 in chloride media.     

Versatility of hydrophilic and antifouling PVDF ultrafiltration membranes tailored with polyhexanide coated copper oxide nanoparticles

Hydrophilic poly(vinylidene fluoride) (PVDF) nanocomposite ultrafiltration (UF) membranes with excellent antifouling and antibiofouling characteristics are fabricated by employing polyhexanide coated copper oxide nanoparticles (P–CuO NPs). The presence of P–CuO NPs is played a significant role in altering the PVDF membrane matrix and probed by XRD, FTIR, FESEM and contact angle analysis. The PVDF/P–CuO nanocomposite membranes exhibited an outstanding antifouling performance indicated by the superior pure water flux, effective foulant separation and maximum flux recovery ratio during UF experiments as a result of the formation of the hydrophilic and more porous membrane due to the uniform distribution of P–CuO NPs. Particularly, the PVDF/P–CuO-3 membrane showed higher PWF of 152.5 ± 2.4 lm⁻²h⁻¹ and porosity of 64.5% whereas the lower contact angle of 52.5°. Further, it showed the higher rejection of 99.5 and 98.4% and the flux recovery ratio of 99.5 and 98.5% respectively for BSA and HA foulants, demonstrated its increased water permeation, foulant separation and antifouling behavior. Further, the decent antibacterial activity is showed by the PVDF/P–CuO nanocomposite membranes with the formation of halo-zone around the membrane when exposed to the bacterial medium demonstrated that, by this process an antibacterial water treatment membrane can be developed by simple phase inversion technique with good membrane stability.     

Green synthesis and characterization of spherical copper nanoparticles as organometallic antibacterial agent

A facile and green route for the synthesis of copper nanoparticles (Cu NPs) has been achieved using green tea extract as a reducing, capping and stabilizing agent. UV–visible spectra gave surface plasmon resonance at 560 nm. The Cu NPs were characterized using various techniques. The size of the Cu NPs was about 20 nm. Antibacterial activity of biogenic Cu NPs were investigated against bacterial species Staphylococcus aureus , Bacillus subtilis , Pseudomonas aeruginosa and Escherichia coli and compared based on diameter of inhibition zone in disc diffusion assay and minimum inhibitory concentration and minimum bactericidal concentration of NPs dispersed in liquid cultures. The NPs showed better inhibitory activity against Gram‐positive bacteria (S. aureus and B. subtilis ) compared to Gram‐negative bacteria. Toxicity of the NPs was evaluated against animal cell line using MTT assay.     

Electrodeposited Cu‐Au Alloy Nanoparticles for Uric Acid Electrochemical Biosensor with Quick Response

A uric acid (UA) electrochemical biosensor based on the Cu‐Au alloy nanoparticles (NPs) and uricase was developed. The electrodeposition technique of Cu‐Au alloy NPs was selected to be a convenient potentiostatic method at –0.8 V in a single solution containing both Au(III) and Cu²⁺. Cyclic voltammetry and scanning electron microscopy proved the successful deposition of Cu‐Au alloy NPs. EIS demonstrated the good conductivity of Cu‐Au alloy NPs. The enzyme was immobilized on the surface of Cu‐Au alloy NPs modified electrode by casting with chitosan solution. The ultimate biosensor showed linear amperometric response towards UA in the concentration range of 3.0 to 26.0 μM with a detection limit of 0.8 μM. The main feature of the biosensor was its short response time, which was attributed to the good conductivity of Cu‐Au alloy NPs. Furthermore, the biosensor could avoid the interference of ascorbic acid and oxygen.     

Adsorption on stainless steel surfaces of biosurfactants produced by gram-negative and gram-positive bacteria: Consequence on the bioadhesive behavior of Listeria monocytogenes

The ability of adsorbed biosurfactants (Pf and Lb) obtained from gram-negative bacterium (Pseudomonas fluorescens) or gram-positive bacterium (Lactobacillus helveticus) to inhibit adhesion of four listerial strains to stainless steel was investigated. These metallic surfaces were characterized using the following complementary analytical techniques: contact-angle measurements (CAM), atomic force microscopy (AFM), polarization modulation-infrared reflection-adsorption spectroscopy (PM-IRRAS) and X-ray photoelectron spectroscopy (XPS). Contact-angles with polar liquids (water and formamide) indicated that the stainless steel surface covered with adsorbed biosurfactant was more hydrophilic and electron-donating than bare stainless steel. The surface characterization by XPS and PM-IRRAS revealed that conditioning the stainless steel changes the substrate in two ways, by modifying the surface alloy composition and by leaving an thin adsorbed organic layer. AFM observations enabled to say that the layer covered entirely the surface and was probably thicker (with patches) in the case of Pf-conditioned surfaces compared to the Lb-conditioned ones, which seemed to be less homogeneous. Though the added layer was thin, significant chemical changes were observed that can account for drastic modifications in the surface adhesive properties. As a matter of fact, adhesion tests showed that both used biosurfactants were effective by decreasing strongly the level of contamination of stainless steel surfaces by the four strains of Listeria monocytogenes. The more important decrease concerned the CIP104794 and CIP103573 strains (>99.7%) on surface conditioned by L. helveticus biosurfactant. A less reduced phenomenon (75.2%) for the CIP103574 strain on stainless steel with absorbed biosurfactant from P. fluorescens was observed. Whatever the strain of L. monocytogenes and the biosurfactant used, this antiadhesive biologic coating reduced both total adhering flora and viable and cultivable adherent bacteria on stainless steel surfaces. This study confirms that biosurfactants constitute an effective strategy to prevent microbial colonization of metallic surfaces by pathogenic bacteria like the food-borne pathogen L. monocytogenes.     

Hydrogen evolution reaction and formic acid oxidation by decorated nanostructural Pt/Pd on a copper-filled nanoporous stainless steel

In this work, a 304 stainless steel (SS) was anodized to prepare nanoporous SS (NPSS) with an average size of about 75 nm and then filled with copper (Cu/NPSS) using pulsed electrodeposition method. Afterward, a nanostructural Pt and Pd film was deposited by galvanic replacement (GR) on the Cu/NPSS to prepare modified electrode (PtPd/Cu/NPSS) for hydrogen evolution reaction (HER) and formic acid electrooxidation (FAO). The electrocatalytic activity of the modified electrode and its structural characterization have been studied by voltammetric methods, electrochemical impedance spectroscopy (EIS), inductively coupled plasma optical emission spectrometry (ICP-OES), and field emission scanning electron microscopy (FESEM). The results show that the nanostructural Pt₁Pd₁/Cu/NPSS composition, with low Pt loading and suitable stability, has a good electrocatalytic performance toward HER (E_Onset = + 12 mV vs. NHE) and FAO (E_Onset = ?180 mV vs. NHE). For HER observed a high mass activity of noble metals (87.54 mA cm^?2μg _Pd+Pt ^?1 ) in comparison with Pt deposited Cu/NPSS (41.5 mA cm^?2 μg _Pt ^?1 ) at the same applied potential of ? 0.25 V versus NHE. Also, the fabricated electrocatalysts with more electrochemically active surface area in comparison with Pd/Cu/NPSS and Pt/Cu/NPSS revealed more resisting to the poisoning components and good stability for FAO.     

Corrosion and biological behavior of nanostructured 316L stainless steel processed by severe plastic deformation

Nanostructured metals have different mechanical, chemical, and physical behaviors in comparison with the microstructured ones. Numerous research studies demonstrated that the biological behavior of nanostructured metallic implants was improved significantly. Concerning the nanostructured metals, decreasing the corrosion rate and the releasing of hazardous ions from metallic implants, and thus increasing the biocompatibility of implants are due to improving the native oxide layer. In the present study, nanostructured 316L stainless steel (biomedical grade) was manufactured via equal channel angular pressing (ECAP) method. To do so, the 316L stainless steel (SS) was exposed to the ECAP operation for eight passes. The impact of the ECAP process on corrosion behavior of SS samples was evaluated through performing the electrochemical polarization corrosion tests in Ringer's solution. Scanning electron microscopy was employed to study the surface morphology of common SS and ECAPed SS sample after the electrochemical polarization tests. Moreover, the biological behavior of the samples was evaluated via cell culture using fibroblast cells. The corrosion test results revealed a substantial decrease of corrosion rate from 3.12 (coarse‐grained sample) to 0.42 μA cm^?2 (for nanostructured). Furthermore, the cell proliferation in the interface of nanostructured sample and cell culture medium enhanced dramatically compared with the coarse‐grained one. The much better biological behavior of nanostructured SS sample in comparison with the coarse‐grained one is mostly due to the significant decrease of corrosion rate on the surface of SS samples, and the presence of much more chrome oxide on the surface of SS sample. Copyright © 2015 John Wiley & Sons, Ltd.     

助剂对Ni-Al合金和Raney-Ni催化剂结构及1,4-丁烯二醇加氢性能的影响

采用等体积浸渍法将助剂(MgO、CuO、Co2O3)引入商品Ni-Al合金粉,经10%(w/w)NaOH溶液浸取制备Raney-Ni催化剂。通过能量色散X射线(EDX)、X射线衍射(XRD)、N2吸附-脱附测试、透射电镜(TEM)、NH3程序升温脱附(NH3-TPD)、X射线光电子能谱(XPS)等方法表征和评价实验,考察了金属助剂对Ni-Al合金粉及Raney-Ni催化剂元素组成、晶相结构、孔结构特征、表面形貌、表面酸碱性的影响。表征分析显示,不同助剂催化剂的元素含量、比表面积及表面形貌均表现出明显的差异。其中,添加助剂Cu的催化剂表面检测到较多的活性组分Ni,接近90%(w/w),该催化剂平均孔径最小(3.87 nm)、活性组分Ni颗粒分散性好。评价结果表明,该催化剂具有较佳的加氢性能,其1,4-丁烯二醇(BED)转化率为100%,1,4-丁二醇(BDO)选择性和收率分别为59.62%和59.62%,这与该催化剂较大的活性组分Ni负载量、酸强度和适中的酸量及存在的Cu对Ni分散性的提高进一步防止了Ni的严重烧结(即"限域效应")等有较大关联。     

天然海水中聚吡咯膜的防微生物附着及防腐蚀性能

采用恒电流法在316 L不锈钢电极表面合成聚吡咯(PPy), 通过开路电位、 生物显微镜(BM)、 Tafel极化曲线及电化学交流阻抗(EIS)研究了聚吡咯防止微生物附着及防腐蚀特性. 研究表明, 沉积聚吡咯的316 L不锈钢电极浸泡在天然海水中(0~20 d), 开路电位基本保持不变, 表明电化学合成的聚吡咯膜有良好的防止微生物附着能力, 并通过生物显微镜进行了验证, 且在浸泡的过程中其腐蚀电流密度维持在10^-7 mA/cm², 表现出良好的防腐蚀特性; 浸泡50 d后, 其防腐蚀效率仍高达97.45%. 因此, 电化学合成的聚吡咯具有优异的防止微生物附着和防腐蚀特性.     

XPS study of silver and copper nanoparticles demonstrated selective anticancer,proapoptotic, and antibacterial properties

Silver and copper nanoparticles were produced by an ecologically safe metal vapor synthesis (MVS) method using acetone as an organic dispersion medium. Transmission electron microscopy (TEM) showed that the specimens are spherical and polydisperse, and their average size is 2.5 nm for silver nanoparticles (Ag NPs) and 2.6 nm for copper nanoparticles (Cu NPs). X-ray photoelectron spectroscopy analyses showed that the state of silver in the nanoparticles is close to that of silver in the Ag⁰ state, whereas copper black contains two oxidized states of the metal—Cu⁺ and Cu²⁺. Biological in vitro studies demonstrated that the nanoparticles have antibacterial activity against Gram-positive and Gram-negative bacterial species. Cu NPs exhibited more prominent antibacterial effects and induced significant growth inhibition of Bacillus cereus and Escherichia coli. Both types of nanoparticles showed anticancer properties in vitro. Cu NPs induced intense cytotoxicity in cancer and normal fibroblasts in vitro cultures, but their inhibitory effect against noncancerous cells was milder compared with cancer cell lines. Ag NPs demonstrated selective cytotoxicity against human lung and cervical adenocarcinoma cell lines. Further in vitro studies indicated that the mechanism of Ag NPs and Cu NPs anticancer effects involves induction of apoptosis. The present study describes a green synthesis approach for production of biologically active silver and copper nanoparticles and highlights their potential for medical application.     

Explaining Cu@Pt Bimetallic Nanoparticles Activity Based on NO Adsorption

Cu@Pt nanoparticles (NPs) are experimentally regarded as improved catalysts for NO_x storage/reduction, with higher activities and selectivities compared with pure Pt or Cu NPs, and with inverse Pt@Cu NPs. Here, a density functional theory-based study on such NP models with different sizes and shapes reveals that the observed enhanced stability of Cu@Pt compared with Pt@Cu NPs is due to energetic reasons. On both types of core@shell NPs, charge is transferred from Cu to Pt, strengthening the NP cohesion energy in Pt@Cu NPs, and spreading charge along the surface in Cu@Pt NPs. The negative surface Pt atoms in the latter diminish the NO bonding owing to an energetic rise of the Pt bands, as detected by the appliance of the d-band model, although other factors, such as atomic low coordination or the presence of an immediate subsurface Pt atom do as well. A charge density difference analysis discloses a donation/back-donation mechanism in the NO adsorption.     

Renewable Surface Sol‐gel Derived Carbon Ceramic Electrode Modified with Copper Complex and Its Application as an Amperometric Sensor for Bromate Detection

A sol‐gel technique was used for the preparation of a three dimensional carbon composite electrode modified with [Cu(bpy)₂]Br₂ complex. A reversible redox couple of Cu(II)/Cu(I) is observed at the electrode surface. The electrochemical behavior and stability of the modified electrode was characterized by cyclic voltammetry. The charge transfer coefficient (α) and charge transfer rate constant (K_s) for the modified electrode were determined by cyclic voltammetry, which were found to be 0.46 and 14.2 s^?1, respectively. The modified electrode showed excellent catalytic activity toward bromate reduction at significantly reduced overpotentials and can be used successfully for amperometric detection of bromate. Under the optimized conditions, the calibration plots are linear in the concentration range 0.5 μM ?200μM. Detection limit (signal to noise is 3) and sensitivity were found to be 0.1 μM and 20 nA / μM, respectively. These analytical parameters compare favorably with those obtained with modern analytical techniques. The modified carbon ceramic electrode doped with Cu‐Complex shows a good reproducibility, a short response time (t<2 s), remarkable long term stability (>4 months) and especially good surface renewability by simple mechanical polishing (RSD for 6 successive polishing is 1.5%).     

Cover Feature: Low-Cost and Scalable Ni-Prussian Blue Analogue//Functionalized Carbon Based Na-Ion Systems for all Climate Operations (ChemPhysChem 4/2023)

Herein, we have developed a sodium ion based aqueous energy storage device with nickel prussian-blue-analogue (Ni-PBA) positive and functionalized carbon-black negative electrodes in 1 M Na₂SO₄ electrolyte solution. The components required to develop the device, i. e., stainless steel (SS) current-collectors, absorbent-glass-mat separator, electrolyte, carbon-black, and precursors of Ni-PBA, are all environmentally benign and inexpensive. To minimize the corrosion of pristine-SS, polyaniline coating on the SS surface is applied by in situ electrodeposition method. The full cell exhibits a specific capacity of 28 mAh g⁻¹ with 90 % Coulomb efficiency (@0.2C), an energy density of 34 Wh kg⁻¹ (@20 W kg⁻¹), a power density of 100 W kg⁻¹ (@18 Wh kg⁻¹) and a good life cycle (70 % capacity-retention over 500 cycles @1.0C rate) within the 0–1.2 V window. The cell performance is further tested under variable temperatures, and 0–50 °C range is reported to be the working window for this cell.     

Growth of cedar-like Au nanoparticles coating on an etched stainless steel wire and its application for selective solid-phase microextraction

A novel cedar-like Au nanoparticles (AuNPs) coating was fabricated on an etched stainless steel (SS) wire by direct chemical deposition and used as an efficient and unbreakable solid phase microextraction (SPME) fiber. The etched SS wire offers a rough surface structure for subsequent growth of AuNPs in chloroauric acid solution. As a result, the uniform cedar-like AuNPs coating with larger surface area was tightly attached to the etched SS wire substrate. The AuNPs coated etched SS fiber (AuNPs/SS) was examined for SPME of ultraviolet (UV) filters, phthalate esters and aromatic hydrocarbons coupled to high-performance liquid chromatography with UV detection. The fabricated fiber exclusively exhibited excellent extraction efficiency and selectivity for some aromatic hydrocarbons. Influential parameters of extraction and desorption time, temperature, stirring rate and ionic strength were investigated and optimized. The limits of detection ranged from 0.008 μg L⁻¹ to 0.037 μg L⁻¹. The single fiber repeatability varied from 3.90% to 4.50% and the fiber-to-fiber reproducibility ranged from 5.15% to 6.87%. The recovery of aromatic hydrocarbons in real water samples spiked at 2.0 μg L⁻¹ and 20 μg L⁻¹ ranged from 94.38% to 106.2% with the relative standard deviations below 6.44%. Furthermore the growth of the cedar-like AuNPs coating can be performed in a highly reproducible manner. This fabricated fiber exhibits good stability and withstands at least 200 extraction and desorption replicates.     

Application of copper nanoparticles containing natural compounds in the treatment of bacterial and fungal diseases

The development of nanotechnology has generated different nanoscale-sized materials, with metal-based nanomaterials being some of the most interesting and promising. Thousands of articles in various specialized journals all over the world are dedicated to different metallic nanomaterials. Metallic nanomaterials are being widely researched, with gold-, silver-, iron-, and copper-based materials showing potential in medicine. Studies have demonstrated the effect of copper nanoparticles in medicinal herbs on the prevention, control, and treatment of microbial diseases. Experiments have examined the chemical characterization and assessment of the antioxidant, cytotoxicity, antibacterial, and antifungal activities of copper nanoparticles (Cu NPs) using the aqueous extract of Stachys lavandulifolia Vahl flower. These nanoparticles were characterized by UV–visible spectroscopy, field emission scanning electron microscopy (FE-SEM), energy dispersive X-ray spectroscopy, transmission electron microscopy (TEM), Fourier-transform infrared spectroscopy (FT-IR), and X-ray diffraction analysis. TEM and FE-SEM images exhibited a uniform spherical morphology and diameters of 10–25 nm for the biosynthesized nanoparticles. FT-IR results suggested polysaccharides and protein in S. lavandulifolia acted as reducing agents, reducing copper ions to Cu NPs. In vitro biological experiments indicated that Cu NPs have excellent antioxidant potential against 2,2-diphenyl-1-picrylhydrazyl, antifungal effects against Candida krusei, Candida parapsilosis, Candida guilliermondii, Candida glabrata, and Candida albicans, and antibacterial activities against Staphylococcus aureus, Enterococcus faecalis, Staphylococcus saprophyticus, Bacillus subtilis, Streptococcus pneumonia, Escherichia coli O157:H7, Salmonella typhimurium, Listeria monocytogenes, Proteus mirabilis, and Pseudomonas aeruginosa. These nanoparticles did not have cytotoxicity properties against human umbilical vein endothelial cells. These results indicate that the inclusion of S. lavandulifolia extract ameliorates the solubility of Cu NPs, which leads to a remarkable enhancement in fungicidal and bactericidal effects under in vitro conditions.