Influence of the Degree of Chitosan Sulfoethylation on the Sorption of Palladium(II) Chloride Complexes from Multicomponent Solutions

The influence exerted by the degree of substitution of sulfoethylated chitosan cross-linked with glutaraldehyde on the sorption of Pd(II) chloride complexes from multicomponent solutions containing Pt(IV), Cu(II), Ni(II), Co(II), Cd(II), and Zn(II) was studied. The sorption of transition metal ions under the conditions of the experiment at pH 0.5–5.0 is virtually fully suppressed. The strongest interfering effect on the Pd(II) sorption is exerted by Pt(IV). Calculation of the selectivity coefficients K_Pd/Pt shows that the selectivity of the Pd(II) sorption relative to Pt(IV) increases with an increase in the degree of substitution of chitosan from 0.3 to 0.5. Integral kinetic curves of the Pd(II) sorption were obtained, and the dependences were subjected to mathematical processing using the models of diffusion and chemical kinetics. The equilibrium in the palladium(II) chloride solution–sorbent system is attained within 40 min. Pd and Pt are quantitatively desorbed from the sorbent surface under dynamic conditions with 3.5 M HCl solution.     

<Emphasis Type="Italic">N</Emphasis>-(2-(2-Pyridyl)ethyl)chitosan (PEC) for Pd(II) and Pt(IV) sorption from HCl solutions

Chitosan was modified by grafting 2-pyridyl-ethyl moieties on the biopolymer backbone for the synthesis of a Platinum Group Metal (PGM) sorbent. The sorbent was tested for Pd(II) and Pt(IV) sorption from HCl solutions. Stable for HCl concentrations below 0.5 M, the sorbent reached sorption capacities as high as 3.2 and 2.6 mmol metal g⁻¹ for Pd(II) and Pt(IV), respectively. Metal sorption mainly proceeds by electrostatic attraction in acidic solutions, though a contribution of complexation mechanism cannot be totally rejected. The resistance to intraparticle diffusion is the main controlling mechanism for uptake kinetics. While agitation speed has a limited effect on kinetics, metal concentration and sorbent dosage have a greater effect on the kinetic profiles. The intraparticle diffusivity varies between 3 × 10⁻¹¹ and 4.5 × 10⁻¹⁰ m² min⁻¹. Thiourea (combined with HCl solution) is used for Pd(II) and Pt(IV) desorption. The resin could be desorbed and recycled for a minimum of five cycles maintaining high efficiencies of sorption and desorption.     

Preconcentration of noble metals with the POLYORGS 4 complexing sorbent under the action of microwave irradiation

The sorption of Au(III), Pd(II), Pt(IV), Rh(III), and Ir(IV) with the POLYORGS 4 complexing sorbent in the static mode was studied at room temperature and on thermal and microwave heating. It was demonstrated that the sorption of noble metals from 1 M HCl and 1 M HNO₃ solutions can be substantially accelerated under the action of microwave irradiation. Based on the obtained data, the conditions of the group preconcentration of noble metals for their subsequent determination by the ETAAS and ICP AES methods were selected. The preconcentration procedure was used for the analysis of certified reference material SARM-7B (platinum-containing ore), VT-1 (copper-nickel sulfide ore), and the alloy of copper with noble metals.     

Sorption recovery of sulfate complexes of iridium on hydrated zirconium dioxide

The sorption on a hydrated zirconium(IV) dioxide from solutions of trinuclear iridium(IV,IV,IV) and iridium(III,III,IV) oxosulfates was studied. The effect of temperature, sorbent grain size, concentration of sulfate complexes of iridium in solution, and acidity of the medium on the sorption recovery was considered.     

Analytical characterization of a silica gel sorbent with thioetheric sites

The sorption behavior of a newly synthesized silica gel sorbent with thioetheric sites (STS) towards microgram levels of Au(III), Pt(IV) and Pd(II) was studied. Au(III) is quantitatively (>95%) sorbed in the pH region of 1–9. The sorption of Pt(IV) starts at pH 1 and does not exceed 25% in the entire pH region examined. The sorption of Pd(II) starts at pH 7 and reaches 80% at pH 9. The sorption of Au(III) on STS at pH 1 is not affected by milligram amounts of Ni(II), Zn(II), Fe(III), Cu(II), Pb(II), Cd(II) or Co(II). Au(III) is quantitatively eluted with a 5% aqueous solution of thiourea. The adsorption capacity of STS towards Au(III) is 195 mg g⁻¹. The detection limit (DL) of Au(III) (3σ, n = 9) is 25 ng mL⁻¹. The RSD at a level of 10 × DL is about 2%. Solid-phase extraction of trace amounts of Au(III) on the STS sorbent, followed by its flame AAS determination in the eluate was applied to the determination of gold in geological samples. The results obtained for the gold content in the samples were in good agreement with those of the ICP-AES analysis.     

Sorption studies of radionuclides on a modified mesoporous cerium(IV) silicate

Five different samples of a new sorbent, modified mesoporous cerium(IV) silicate have been prepared with various mole ratios of Si/Ce and Cetyltrimethylammonium bromide (CTMABr) as template. XRD, nitrogen sorption, SEM, IR, thermogravimetry and sorption of radionuclides have been studied. Separation of Hg(II)-Th(IV), Hg(II)-Zr(IV) and Rb(I)-Zr(IV) have been developed on columns of this novel sorbent.     

Sorption of noble-metal ions on silica with chemically bonded nitrogen-containing ligands

A study has been made of the sorption of Ir(IV), Rh(III), Pt(IV), Ru(IV), Os(VIII), Pd(II) and Au(III) from aqueous solutions by silica chemically modified with nitrogen-containing organic ligands, as a function of hydrochloric acid concentration, time of contact, concentration of the element and the ionic strength. Sorption of noble-metal ions at pH > 1 on a sorbent containing monoamine groups seems to be due to a complexation mechanism, and to an anion-exchange mechanism at pH < 1. With aminopropyl-silica 1000-fold concentration of Ir(IV) and Rh(III) from their 10(-8)-10(-7)M solutions was achieved and these metals were subsequently determined on the sorbent surface by X-ray fluorescence. Detection limits were 10-20 ng/ml. There was no interference from 1000-fold quantities of non-ferrous metal ions and Fe(III). With the sorbent containing bonded diethylenetriamine groups, 1000-fold concentration of Au(III) was achieved, and it was then determined on the sorbent surface by an atomic-emission method. Conditions for desorption of Au(III) with pyridine and potassium thiocyanate were developed.     

Selective solid phase extraction of platinum on an ion imprinted polymers for its electrothermal atomic absorption spectrometric determination in environmental samples

An ion-imprinted polymer (IIP) was obtained by copolymerization of methacrylic acid (as a functional monomer) and ethylene glycol dimethacrylate (as a crosslinking agent) in the presence of various chelators for Pt(II) ion and using 2,2??-azo-bis-isobutyronitrile as the initiator. Specifically, acetaldehyde thiosemicarbazone (AcTSn) and benzaldehyde thiosemicarbazone (BnTSn) were used as chelators. The IIPs were applied as sorbents for solid-phase extraction of Pt(II) and Pt(IV) ions from aqueous solutions. The effects of acidity and flow rate of the sample, of elution conditions and of potentially interfering ions were investigated. The imprinting effect of analyte is clearly demonstrated by the fact that only the IIP is capable of quantitative retention of Pt(II) and Pt(IV) ions. The method works best in the pH range from 0.5 to 1 and from 3.5 to 9.5. The ions can be recovered with an acidic solution of thiourea. The Pt-AcTSn polymer displays better sorption properties for the separation of analytes. The selectivity coefficients of the Pt-AcTSn and control polymers for Pt(IV) in the presence Pd(II), Rh(III), Ru(III), Al(III) and Cu(II) were calculated, and the sorbent capacity for Pt(IV) was found to be 4.56???g?g?^-1. The method was successfully applied to the determination of Pt(IV) by electrothermal atomic absorption spectrometry in tap water, tunnel dust and anode slime samples.

Evaluation of Se(IV) removal from aqueous solution by GMZ Na-bentonite: batch experiment and modeling studies

Bentonite has been studied extensively because of its strong sorption and complexation ability. In this work, the sorption of Se(IV) on purified GMZ bentonite was investigated under ambient temperature as functions of contact time, pH, Se(IV) concentration and co-existing ion Eu(III) using batch techniques. Sorption kinetics of Se(IV) was successfully described by the pseudo-second-order rate equation. The sorption amount of Se(IV) was strongly dependent on the solution pH, and a positive effect was observed on Se(IV) and Eu(III) co-sorption when these two elements existed in the same system under high surface coverage of sorbent. Double layer model was set up and used to quantitatively interpret the sorption experimental data collected in binary and ternary sorption systems. From the experimental results, one can conclude that GMZ bentonite may have good potentialities for immobilizing selenium in nuclear wastes.     

1-(2-氨乙基)吡咯烷树脂的合成及其对贵金属的吸附

研究了试剂摩尔比、反应温度、反应时间对1-(2-氨乙基)吡咯烷树脂合成的影响规律.此树脂的功能基含量2.74 mmol/g树脂,对Au(Ⅲ)、Os(Ⅳ)、Pt(Ⅳ)、Ir(Ⅳ)、Ru(Ⅲ)、Pd(Ⅱ)的吸附容量分别高达950、520、436、418、314、302 mg/g树脂.FT-IR、元素分析表征了树脂结构.测定了吸附速率曲线,配位比,表观吸附活化能△E_(Au)=6.4、△E_(Pt)=33.7kJ/mol.XPS研究了吸附机理.     

Preparation and characterization of new sol–gel titanium(IV) butoxide–cyanopropyltriethoxysilane hybrid sorbent for extraction of polar aromatic amines

A new titanium(IV) butoxide-cyanopropyltriethoxysilane (Ti-CNPrTEOS) hybrid material was successfully synthesized for the use as sorbent for the extraction of polar aromatic amines. The sorbent was synthesized by hydrolysis and condensation of titanium(IV) butoxide and cyanopropyltriethoxysilane with the presence of hydrochloric acid as catalyst via sol–gel method. Several factors influencing the synthesized sorbent such as solvent selection, mol of water content, ratio of titanium(IV) butoxide and cyanopropyltriethoxysilane and aging temperature were investigated and optimized. The sorbents were characterized by fourier transform-infrared, field-emission scanning electron microscopy-energy, CHN elemental analysis and thermogravimetric analysis. The applicability of the sorbents for the extraction of polar aromatic amines by the batch sorption method was extensively studied and evaluated. Under the optimum synthesis conditions (tetrahydrofuran as solvent, 1.2 M of hydrochloric acid catalyst, 4 mol of water content with ratio of titanium(IV) butoxide and cyanopropylteriethoxysilane of 1:1 and aging temperature of 60 °C), the extraction showed high recovery towards the extraction of polar aromatic amines. The synthesized sorbent was successfully applied for the extraction of selected aromatic amines via batch sorption method in waste water samples prior to the gas chromatography-flame ionization detector separation. The synthesized sol–gel Ti-CNPrTEOS sorbent demonstrated the potential as an alternative extraction sorbent with higher selectivity towards polar aromatic amines.     

Sorption of Th(IV) from aqueous solution to GMZ bentonite: effect of pH, ionic strength, fulvic acid and electrolyte ions

Bentonite has been studied extensively because of its strong sorption and complexation ability. In this study, GMZ bentonite (China) was studied as a potential sorbent for the removal of Th(IV) from aqueous solutions. The results indicate that the sorption of Th(IV) is strongly dependent on pH and ionic strength at pH <5, and is independent of ionic strength at pH >5. Outer-sphere surface complexation or ion exchange in inter-layer sites of the montmorillonite fraction of the GMZ bentonite may be the main sorption mechanism of Th(IV) onto GMZ bentonite at low pH values, whereas the sorption of Th(IV) at pH >5 is mainly dominated by inner-sphere surface complexation or surface precipitation. The presence of soil fulvic acid has a positive influence on the sorption of Th(IV) on GMZ bentonite at pH <5. The competition between Th(IV) with aqueous or surface adsorbed cation ions (e.g., herein Li⁺, Na⁺ and K⁺) and surface functional groups of GMZ bentonite is important for Th(IV) sorption on GMZ bentonite. The results of high sorption of Th(IV) suggest that the GMZ bentonite is a suitable backfill material in nuclear waste management.     

Complexation of palladium and platinum on silica gel with grafted N-(2,6-dimethyl-4-methyltriphenylphosphonium chloride)-phenyl-N′-propylthiourea groups

We have studied processes of sorption of palladium and platinum from aqueous solutions on silica gel with N-(2,6-dimethyl-4-methyltriphenylphosphonium chloride)phenyl-N′-propylthiourea groups covalently bonded to the SiO₂ surface. We have established that Pd(II) is sorbed according to a complexation mechanism, while Pt(II,IV) is sorbed according to simultaneously a complexation mechanism and an anion-exchange mechanism, followed by rearrangement processes occurring on the surface of the sorbent. Translated from Teoreticheskaya i éksperimental'naya Khimiya, Vol. 36, No. 3, pp. 188–192, May–June, 2000.     

Sorption recovery of platinum(II) and platinum(IV) chloro complexes with a heterochain sulfur-containing sorbent

The recovery of platinum(II) and platinum(IV) chloro complexes from hydrochloric acid and chloride solutions with a new heterochain S,N-containing sorbent, MITKhAT, was studied. The suggested mechanism of formation of platinum(II) mercapto-thio ether complexes in the course of sorption was confirmed by DFT calculations. The results of group and selective recovery of platinum metals with MITKhAT sorbent from simulated and real industrial solutions are reported.     

Highly efficient adsorbing noble metal ions by 3,4-dihydroxycinnamic acid-modified activated carbon

A method was established for the preconcentration of trace Au(III), Pd(II) and Pt(IV) by activated carbon modified with 3,4-dihydroxycinnamic acid. The separation and preconcentration conditions of analytes were investigated, such as effects of pH, the contacting time, the sample ?ow rate and volume, the elution condition and the interfering ions. At a pH of 1.0, the maximum static sorption capacity of the sorbent was found to be 374.8, 96.6 and 137.5 mg g^?1 for Au(III), Pd(II) and Pt(IV), respectively. The adsorbed metal ions were effectively eluted with 2.0 mL of 4% thiourea in 0.5 M HCl solution and determined by inductively coupled plasma optical emission spectrometry. The detection limit (3σ) of this method defined by IUPAC was found to be 0.12, 0.18 and 0.32 ?g L^?1 for Au(III), Pd(II) and Pt(IV), respectively. The relative standard deviation (RSD) was lower than 3.0% (n = 8) towards standard solutions. The method has been validated by analysing certified reference materials and successfully applied to the determination of trace Au(III), Pd(II) and Pt(IV) in road sediments samples.     

Specificity of noble metals dynamic sorption preconcentration on reversed-phase sorbents

The reversible sorption preconcentration of noble metals (NMs) using different schemes “sorbent–reagent–eluent” was investigated. The extraction of Au, Pd, Pt, Ir, Rh and Ru chlorocomplexes from hydrochloric acid solutions on hyper-crosslinked polysterene MN-200 in the form of ion associates with tributylamine (TBA) and 4-(n-octyl)diethylenetriamine (ODETA) was investigated. It was found that Pd, Pt and Au were quantitatively and reversibly extracted using TBA on hyper-crosslinked polysterene; the appropriate eluent for desorption was 1 M solution of HCl in ethanol. Ir, Rh and Ru under these conditions were not sorbed quantitatively. It was found that sorbent hydrophobicity is not the main characteristic that defines the efficiency of sorption of a particular NM ion associate. Different efficiencies of hyper-crosslinked polysterene MN-200 for sorption of square-planar chlorcomplexes of Pt, Pd and Au and octahedral complexes of Ir, Rh and Ru were found. For the first time, the sorbents with their own N-atoms – StrataX and StrataX-AW – were used for the sorption of Ir, Rh and Ru. Using these sorbents, the sorption of Ir was increased up to 95%, and the sorption of Ru and Rh was increased to about 40%. We can explain these results by nonspecific interaction of chlorcomplexes of Ir, Rh and Ru with ethylenediamine groups of the sorbent. Weak bases with large anions may be applied for desorption of Ir, Rh and Ru. Two schemes of dynamic sorption preconcentration of NMs from hydrochloric acid solutions were proposed – hyper-crosslinked polysterene MN-200 for the determination of Au, Pd, Pt, and StrataX-AW for Ir, Rh and Ru.     

Sorption of Th(IV) ions onto TiO2: Effects of contact time, ionic strength, thorium concentration and phosphate

Summary The sorption of Th(IV) onto TiO₂ was studied by the batch technique as a function of pH and ionic strength at moderate concentration (10^-4-10^-5 mol/l) and in the presence and absence of phosphate. It was found that the sorption rate of Th(IV) was relatively slow, the sorption percent was abruptly increased from pH 2 to 4, and the sorption was decreased with increasing ionic strength as a whole. In the concentration range of Th(IV) from trace concentration to 1.4 ^. 10^-4 mol/l and in the absence of phosphate, the sorption isotherms were roughly fitted the Freundlich equation at different ionic strengths and approximately constant pH. These sorption characteristics of Th(IV) onto TiO₂ were compared with those of uranyl on the same sorbent. In addition, the positive effect of phosphate on the sorption of Th(IV) onto TiO₂ was demonstrated obviously and can be attributed to strong surface binding of phosphate, and the subsequent formation of ternary surface complexes of Th(IV). The difference between the sorption characteristics of Th(IV) ions and uranyl ions onto TiO₂ is discussed.     

Trace analysis of Pt (IV) metal ions in roadside soil and water samples by Fe3O4/graphene/polypyrrole nanocomposite as a solid-phase extraction sorbent followed by atomic absorption spectrometry

A novel Fe₃O₄/graphene/polypyrrole nanocomposite has been successfully synthesised via a simple chemical method and applied as a new magnetic solid-phase extraction (MSPE) sorbent for the separation and pre-concentration of trace amounts of Pt (IV) in environmental samples followed by flame atomic absorption spectrometric (FAAS) detection. The nanocomposite has been characterised by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Fourier transform infrared (FTIR) spectroscopy. Seven important parameters, affecting the extraction efficiency of Pt (IV), including pH, adsorption time, desorption solvent type and concentration, desorption time, elution volume and sample volume, were investigated. Under the optimised conditions, the calibration graph was linear in the range of 50–1500 μg L^?1 (R = 0.993). The detection limit and pre-concentration factor (PF) for Pt (IV) were found to be 16 μg L^?1 and 112.5, respectively. Under the optimised solid-phase extraction (SPE) conditions, the adsorption isotherm and the adsorption capacity of the nanocomposite for Pt (IV) were studied. Pt (IV) adsorption equilibrium data were fitted well to the Langmuir isotherm and the maximum adsorption capacity of the magnetic sorbent was calculated from the Langmuir isotherm model as 416.7 mg g^?1. The precision of the method was studied as intraday and interday variations. A relative standard deviation percentage (RSD%) value less than 3.0 indicates that the method is precise. Also, the accuracy of the method was tested by the analysis of the standard reference material (NIST SRM 2556) and by recovery measurements on spiked real samples. It was also shown that the optimised method was suitable for the analysis of trace amounts of Pt (IV) in roadside soil, tap water and wastewater samples.     

Sorption Purification of Scandium(III) To Remove Zirconium(IV) Impurity in Hydrochloric Acid Solutions

A study was made on separation of the Zr(IV) impurity from scandium(III) in hydrochloric acid solutions by sorption with KRF-20t-60 cation exchanger, including sorption kinetics and sorption under dynamic conditions. The sorbent regeneration with 5% ammonium fluoride or 10% potassium carbonate at 22°C was considered.     

Palladium and platinum sorption using chitosan-based hydrogels

Two chitosan hydrogels (prepared by NaOH neutralization and by polyphosphate ionotropic gelation) have been tested in the dry state for Pd(II) and Pt(IV) sorption at pH 2. Similar sorption isotherms with maximum sorption capacities close to 190 mg Pd g⁻¹ and 235 mg Pt g⁻¹ were achieved. The sorption mechanism involves electrostatic attraction of the chloro-anionic species onto protonated amine groups; the drastic decrease of sorption capacity with the addition of chloride ions supports this hypothesis. SEM-EDAX analysis suggests that sorption proceeds, in kinetic terms, through a shrinking core mechanism. Metal ions can diffuse throughout all the sorbent volume. The main differences between the sorbents are revealed by kinetics. The hydrogels prepared by ionotropic gelation in polyphosphate (C-PPh) allows reaching equilibrium much faster than the hydrogels prepared by the neutralization process (C-NaOH). While for C-PPh sorbent the chemical reaction rate seems to control sorption profiles, in the case of C-NaOH a combination of mechanisms including intraparticle diffusion resistance controls uptake kinetics. Metal desorption from loaded sorbents is possible using thiourea alone or in association with HCl solutions. The recycling of the sorbents is possible but for a limited number of cycles.