Au core-PtAu alloy shell nanowires for formic acid electrolysis

Inefficient electrocatalysts and high-power consumption are two thorny problems for electrochemical hydrogen(H2)production from acidic water electrolysis.Herein we report the one-pot precise synthesis of ultrafine Au core-Pt Au alloy shell nanowires(Au@PtxAu UFNWs).Among them,Au@Pt_0.077 Au UFNWs exhibit the best performance for formic acid oxidation reaction(FAOR)and hydrogen evolution reaction(HER),which only require applied potentials of 0.29 V and-22.6 m V to achieve a current density of 10 m A cm^-2,respectively.The corresponding formic acid electrolyzer realizes the electrochemical H2 production at a voltage of only 0.51 V with 10 m A cm^-2 current density.Density functional theory(DFT)calculations reveal that the Au-riched Pt Au alloy structure can facilitates the direct oxidation pathway of FAOR and consequently elevates the FAOR activity of Au@Pt_0.077 Au UFNWs.This work provides meaningful insights into the electrochemical H₂ production from both the construction of advanced bifunctional electrocatalysts and the replacement of OER.     

Layered Ag-graphene films synthesized by Gamma ray irradiation for stable lithium metal ano des in carb on ate-based electrolytes

Lithium metal batteries are considered as high energy density battery systems with very promising prospects and have bee n widely studied.However,The uncon trollable plating/strippi ng behavior,infinite volume change and den drites formation of lithium metal anode restrict the applicati on.The unc on trolled n ucleati on of lithium caused by the non uniform multi-physical field distributions,can lead to the undesirable lithium deposition.Herein,a graphene composite uniformly loaded with Ag nano-particles(Ag NPs)is prepared through a facile Gamma ray irradiation method and assembled into self-supported film with layered structure(Ag-rGO film).Whe n such film is used as a lithium metal an ode host,the uncontrolled deposition is converted into a highly nucleation-induced process.On one hand,the Ag NPs distributed between the in terlayers of graphe ne can preferentially induce lithium nu cleati on and en able uniform deposition morphology of lithium between interlayers.On the other hand,the stable layered graphene structure can accommodate volume change,stabilize the interface between anode and electrolyte and inhibit dendrites formation.Therefore,the layered Ag-rGO film as anode host can reach a high Coulombic efficiency over 93.3% for 200 cycle(786 h)at a current density of 1 mA cm^-2 for 2 mAh cm^-2 in carbonate-based electrolyte.This work proposes a facile Gamma ray irradiation method to prepare metal/3D-skeleton structure as lithium anode host and demonstrates the potential to regulate the lithium metal deposition behaviors via manipulating the distribution of lithiophilic metal(e.g.Ag)in 3D frameworks.This may offer a practicable thinking for the subsequent design of the lithium metal anode.     

中国纤维素乙醇技术的研究进展

中国面临着严重的能源短缺和环境污染问题,中国政府正在局部几个省份内政策性鼓励燃料乙醇生产和使用.尽管当前主要是用玉米和谷物作为生产乙醇的原料,然而中国具有大量潜在的低成本的纤维素生物质原料,可以极大地扩大乙醇的产量,降低原料成本.近20年来,由于技术的革命性进步,已使得纤维素乙醇的生产成本从4美元/加仑以上,降低至约1.2-1.5美元/加仑.其中,每吨生物质约44美元.因此,目前乙醇掺汽油具有十分强的市场竞争力.已有几个公司正在建造首批商业纤维素乙醇工厂,虽然这些刚起步的小型设施在合理利用和管理上风险较小,但规模经济需要较大型工厂.尽管配送生物质原料的成本会随需求的增加而增加,但在乙醇生产基础上的生物精炼技术的发展,尤其是化工产品和动力的协同生产,将会使全过程的经济可行性大大提高.进一步深入的基础研究,将解决低成本下实现纤维素的完全利用,以确保在无政策性补贴的前提下,真正使纤维素乙醇成为具有市场竞争力的低成本纯液体燃料.     

Binary ligand strategy toward interweaved encapsulation-nanotubes structured electrocatalyst for proton exchange membrane fuel cell

Hierarchically porous architecture of ir on-nitroge n-carb on(Fe-N-C)for oxyge n reducti on reaction(ORR)is highly desired towards efficient mass transfer in the fuel cell device manner.Herein,we reported a binary ligand strategy to prepare zeolitic imidazolate frameworks(ZIFs)-derived precursors,wherein the addition of secondary ligand endows precursors with the capabilities to transform into porously interweaved encapsulation-nanotubes structured composites after calcination.The optimal catalyst,i.e.,termed as Fe₆-M/C-3,exhibits excellent durability with 88.8%current retention after 50,000 seconds in 0.1 M HClO₄solution by virtue of nanoparticles-encapsulation features,which is more positive than the benchmark commercial 20 wt%Pt/C catalyst.Moreover,a promising maximum power density of Fe₆-M/C-3 as cathode catalyst was also dem on strated in proton exchange membrane fuel cells(PEMFCs)measurements.Therefore,this binary ligand approach to the fabrication of hierarchically porous structures would also have significant implications for various other electrochemical reactions.     

Molten salt as ultrastrong polar solvent enables the most straightforward pyrolysis towards highly efficient and stable single-atom electrocatalyst

Currently,pyrolysis as the most widely used method still has some key issues not well resolved for synthesis of carbon-supported single-atom catalysts(C-SACs),e.g.,the sintering of metal atoms at high temperature as well as the high cost and complicated preparations of precursors.In this report,molten salts are demonstrated to be marvellous medium for preparation of C-SACs by pyrolysis of small molecular precursors(ionic liquid).The ultrastrong polarity on one hand establishes robust interaction with precursor and enables better carbonization,resulting in largely enhanced yield.On the other hand,the aggregation of metal atoms is effectively refrained while no nanoparticle or cluster is formed.By this strategy,a C-SAC with atomically dispersed Fe-N₄ sites and a high specific area over 2000 m² g^-1 is obtained,which illustrates high ORR activity in both acid and alkaline media.Moreover,this SAC exhibits superior methanol tolerance and stability after acid soaking at 85℃ for 48 h.It is believed that the molten-salts-assisted pyrolysis can be developed into a routine strategy as it not only can largely simply the synthesis of C-SACs,but also can be extended to prepare other types of SACs.     

镧对Mg-Si合金中Mg2Si相变质的影响

研究了Mg-5Si合金中La的添加对初生Mg2Si相变质的影响。结果表明,适量的La能够有效地变质初生Mg2Si相。基于本文的研究,在添加约0.5%La时,获得了最佳的变质效果,此时,初生Mg2Si相的尺寸减小到25μm以下,其形态从粗大的树枝形状变为多面体形状。然而,当La增加到0.8%或者更高时,初生Mg2Si相又生长为粗大的树枝形态。而且,在凝固过程中发现形成了一些LaSi2化合物,这些化合物的数量随着La的增加而呈现逐渐增加的趋势。     

电感耦合等离子体质谱法测定天然水体中19种元素

建立STD/KED模式-电感耦合等离子体质谱（ICP-MS）法同时测定天然水体中铍、硼、钛、钒、铬、锰、钴、镍、铜、锌、钼、镉、锑、钡、铊、铅、铁、砷和硒19种元素的分析方法。仪器调谐校准后,样品在线加入锂、钪、铑、铋校准溶液校正,以标准曲线内标法定量分析。标准曲线相关系数均大于0.999,样品加标回收率为92.6%～103.6%,质控样品测定值相对标准偏差为0.20%～2.6%(n=6),方法检出限为0.01～0.70μg/L。该方法灵敏度高,操作简便,节省人力,能满足天然水体中19种元素的同时检测需要。     

二氧化钛纳米管的研究进展

二氧化钛纳米管由于其新奇的光电、催化、气敏等性能引起了广泛的关注,在太阳能电池、光催化、环境净化、气体传感器等领域有潜在的应用价值.本文概述了近年来在制备方法、反应机理和组成、晶型和形貌及掺杂和应用方面的进展,并讨论了今后可能的研究发展方向.     

Uncommon Intramolecular Charge Transfer Effect and Its Potential Application in OLED Emitters

Planarized intramolecular charge transfer(PLICT)state can facilitate the fluorescence process thanks to the relative excellent planarity.Recently,we have discovered that the excited state quinone-conformation induced planarization(ESQIP)occurring on tetraphenylpyrazine(TPP)based derivatives could furnish them with PLICT feature.Unlike to the well-known intramolecular charge transfer,strengthening the electron-donating nature on the donor(D)moiety did not impair the PLICT.The calculation results showed that planarization of the TPP based compounds scarcely accompanied with energy wastage while amount of energy was required for the torsion on geometries.In the polar solvents,the energy consumption for planarization could further decrease,but that for twisting structure would increase.To take advantage of the transformation of the frontier orbitals'distribution,the PLICT type materials would perform a potential application on organic light-emitting diodes(OLEDs).     

Hierarchical structured CoP nanosheets/carbon nanofibers bifunctional eletrocatalyst for high-efficient overall water splitting

The design of efficient,stable,and economical electrocatalysts for oxygen and hydrogen evolution reaction(OER and HER)is a major challenge for overall water splitting.Herein,a hierarchical structured CoP/carbon nanofibers(CNFs)composite was successfully synthesized and its potential application as a high-efficiency bifunctional electrocatalyst for overall splitting water was evaluated.The synergetic effect of two-dimensional(2D)CoP nanosheets and on e-dimensi on al(1D)CNFs endowed the CoP/CNFs composites with abundant active sites and rapid electron and mass transport pathways,and thereby significantly improved the electrocatalytic performances.The optimized CoP/CNFs delivered a current density of 10 mA cm^-2 at low overpotential of 325 mV for OER and 225 mV for HER.In the overall water splitting,CoP/CNFs achieved a low potential of 1.65 V at 10 mA cm^-2.The facile strategy provided in the present work can facilitate the design and development of multifunctional non-noble metal catalysts for energy applications.     

SYNTHESIS AND CHARACTERIZATION OF HETEROAROMATIC POLYMERS CONTAINING PYRIDINE MOIETIES

1. INTRODUCTION The new kinds of heteroaromatic polymers have been important topics in polymer science fields since they were developed at 1960s in order to meet demands for heat-resistant plastics for space and military applications. Because heteroaromatic polymers exhibit excellent thermal and chemical stability, outstanding electrical and mechanical properties, good solvent resistance, and dimensional stability, these polymers have found usage as adhesives, coatings, matrix resins, film…     

Soluble blue light emitting pyridine-containing polymers prepared by oxidative-coupling copolymerization

Novel polymers containing pyridine moieties in main chains have been prepared by facile oxidative-coupling co-polymerization of pyridine N-oxide with N-alkyl carbazole and fluorene as the precursor polymers, which were reduced to the pyridine-containing polymers respectively. The polymers were characterized by FT-IR, ¹H NMR, UV-Vis, X-ray, thermo-gravimetric analysis, and fluorescence spectroscopy. The pyridine-containing polymers good solubility in convenient organic solvents, high thermal stability with the onset decomposition temperature above 310 °C. The electrochemical behaviors of the polymers were investigated by cyclic voltammetry; the HOMO and LUMO energy level of the polymers were estimated from the electrochemistry and UV-Vis spectroscopy. The fluorescence spectra of the pyridine-containing polymers display blue light emitting properties in both solution and solid-state film.     

Synthesis and Characterization of Novel Polyimides Based on Pyridine-containing Diamine

A new aromatic diamine monomer containing pyridine unit, 2,6-bis （4-aminophenoxy- 4＇-benzoyl）pyridine（BABP）, was synthesized in three steps, starting from 2,6-pyridinedicarboxyl chloride. A series of novel pyridine-containing polyimides were prepared v/a the polycondensation of BABP with various aromatic dianhydrides through poly（amic acid） precursors, and thermal or chemical imidization of the precursors. The polyimides exhibit desirable properties, e.g., good solubility in N-methyl-2-pyrrolidone and m-cresol, excellent thermal stability and film-forming capability, as well as high inherent viscosity, indicating high molecular weight.     

主链含吡啶环的聚合物

介绍了国内外有关主链含吡啶环聚酰胺、聚酰亚胺、聚苯并咪唑、聚吡咙、聚酯以及聚氨酯等芳杂环或杂链高分子的研究，特别着重于含吡啶环的二元酚、二元酸、二元胺、四元胺类单体以及主链含吡啶环聚合物的分子设计、合成反应、结构与性能表征等。     

Synthesis and properties of poly(thioether amide)s from 2,6-bis(acrylamido)pyridine and dithiols

Poly(thioether amide)s containing pyridine moieties in their backbone were obtained by the polyaddition of 2,6-bis(acrylamido)pyridine (2,6-BAAP), derived from 2,6-diaminopyridine and acryloyl chloride, with an aromatic or aliphatic dithiol. The influence of various reaction conditions on the polyaddition was investigated in comparison with the polyaddition of 1,3-bis (acrylamido)benzene (1,3-BAAB). 2,6-BAAP gave the polymer even in the absence of any initiator at lower temperatures while 1,3-BAAB did not, which was attributable principally to intramolecular base catalysis of the pyridine moieties. Basic additives effectively promoted the reaction rate and increased the chain length. Those facts and NMR of the resulting polymers indicated Michael-type polyaddition. The polymers from 2,6-BAAP were amorphous and gave transparent and tough films having a high refractive index exceeding 1.7. GPC and DSC characterizations were also made. © 1993 John Wiley & Sons, Inc.     

含二氦杂萘酮结构全芳香杂环聚合物的研究进展

高性能高分子材料在高温下仍保持优异的综合性能,是航空航天、电子电气、高速轨道交通等重要高技术领域不可或缺的材料。在不牺牲耐热性能的前提下改善高性能聚合物的加工性能一直是国内外研究的热点。含二氮杂萘酮结构高性能聚合物是高性能高分子材料的新成员。本文主要综述了含二氮杂萘酮结构的聚芳醚（包括聚芳醚砜酮系列、聚芳醚腈砜酮系列、...     

Synthesis of a new aromatic diacid containing pyridine ring and related polybenzimidazole

<正>A new aromatic diacid monomer containing pyridine unit,4-phenyl-2,6-bis[4-(4-carboxyphenoxy) phenyl]pyridine 3,was successfully synthesized in three steps,starting from 4-hydroxyacetophenone.The corresponding pyridine-containing polybenzimidazole was prepared via polycondensation of 3 with tetraaminodiphenyl ether(TADE) in poly(phosphoric acid)(PPA).The resulting polybenzimidazole exhibits excellent solubility,good thermal stabilities and high thermal resistance.     

新型氯取代含杂萘联苯结构可溶性聚芳酰胺的合成、表征和性能

以类双酚单体4-(3-氯-4-羟基-苯基)-2H-二氮杂萘-1-酮(DHPZ-OC)和对氯苯腈为原料进行亲核取代反应合成二腈化合物4-[3-氯-4-(4-氰基苯氧基)苯基]-2-(4-氰基苯基)二氮杂萘-1-酮(),然后在碱性(KOH)条件下进行水解制得了一种新型的含氯取代杂萘联苯结构的芳香二酸,4-[3-氯-4-(4-羧基苯氧基)苯基]-2-(4-羧基苯基)二氮杂萘-1-酮().用新二酸与各种芳香二胺进行直接缩合聚合制得了一系列新型氯取代含杂萘联苯结构的聚芳酰胺,特性粘度可达1.23dL/g.用FTIR和¹HNMR研究了新型二酸单体及聚合物的结构.该类聚芳酰胺均可溶解于NMP,DMAc和DMSO等极性有机溶剂中,并且可浇铸成透明韧性膜,其玻璃化转变温度在291～332℃之间,10%的热失重温度在460℃以上.     

Bandgap Engineering through Controlled Oxidation of Polythiophenes

The use of Rozen’s reagent (HOF?CH₃CN) to convert polythiophenes to polymers containing thiophene‐1,1‐dioxide (TDO) is described. The oxidation of polythiophenes can be controlled with this potent, yet orthogonal reagent under mild conditions. The oxidation of poly(3‐alkylthiophenes) proceeds at room temperature in a matter of minutes, introducing up to 60 % TDO moieties in the polymer backbone. The resulting polymers have a markedly low‐lying lowest unoccupied molecular orbital (LUMO), consequently exhibiting a small bandgap. This approach demonstrates that modulating the backbone electronic structure of well‐defined polymers, rather than varying the monomers, is an efficient means of tuning the electronic properties of conjugated polymers.     

Influence of charge on anion receptivity in amide-based macrocycles

Binding and structural aspects of anions with tetraamido/diquaternized diamino macrocyclic receptors containing m-xylyl, pyridine, and thiophene spacers are reported. (1)H NMR studies indicate that the quaternized receptors display higher affinities for anions compared to corresponding neutral macrocycles. The macrocycles containing pyridine spacers consistently display higher affinity for a given anion compared to those with either m-xylyl or thiophene spacers. The m-xylyl- and pyridine-containing receptors exhibit high selectivity for H(2)PO(4)(-) in DMSO-d(6) with association constants, K(a) = 1.09 × 10(4) and >10(5) M(-1), respectively, and moderate selectivity for Cl(-) with K(a) = 1.70 × 10(3) and 5.62 × 10(4) M(-1), respectively. Crystallographic studies for the Cl(-) and HSO(4)(-) complexes indicate that the m-xylyl-containing ligand is relatively elliptical in shape, with the two charges at ends of the major axis of the ellipse. The anions are hydrogen bonded with the macrocycle but are outside the ligand cavity. In the solid state, an unusual low-barrier hydrogen bond (LBHB) was discovered between two of the macrocycle's carbonyl oxygen atoms in the HSO(4)(-) complex. The pyridine-containing macrocycle folds so that the two pyridine units are face-to-face. The two I(-) ions are chelated to the two amides adjacent to a given pyridine. In the structure of the thiophene containing macrocycle with two BPh(4)(-) counterions, virtually no interaction was observed crystallographically between the macrocycle and the bulky anions.