磁场和稀土Ce介入下化学镀Co-Ni-B合金的晶化行为

化学镀钴-镍-硼;晶体结构;稀土重金属;磁场和稀土Ce介入下化学镀Co-Ni-B合金的晶化行为     

粉末化学镀负载型NiB/MgO非晶态合金及其加氢催化性能

粉末化学镀负载型NiB/MgO非晶态合金及其加氢催化性能;NiB/MgO;非晶态合金;粉末化学镀;环丁烯砜加氢     

磁场诱导制备Fe-B非晶态合金纳米线及其磁学性质

通过引入外加直流电磁场, 采用KBH4还原法在室温下制备了一维Fe-B非晶态合金纳米线, 并采用X射线衍射(XRD)、电感耦合等离子原子发射光谱仪(ICP-AES)和扫描电子显微镜(SEM)等表征方法研究了产物的结构、组成和形貌. 结果表明, 在直流电磁场的作用下得到了Fe-B非晶态合金纳米线, 所得样品的直径在50-80 nm之间, 长度达到数微米. 通过振动样品磁强计(VSM)研究其磁学性质, 发现外加磁场的引入会显著影响Fe-B非晶态合金的磁学性质. 随着引入磁场强度的增强, 所得样品的饱和磁感应强度和矫顽力明显区别于未引入磁场制备的Fe-B非晶态合金.     

钢铁表面Ni-Sn-P合金镀层组成及其耐蚀性

化学镀;钢铁表面Ni-Sn-P合金镀层组成及其耐蚀性     

2,2′-联吡啶和亚铁氰化钾对乙醛酸化学镀铜的影响

以乙醛酸作还原剂、Na2EDTA为络合剂、2,2′-联吡啶和亚铁氰化钾作为添加剂组成化学镀铜体系,研究了两种添加剂对化学镀铜速率、镀层表面形貌、组成和结构的影响.结果表明:添加适量的2,2′-联吡啶和亚铁氰化钾,不仅提高了镀液的稳定性,而且使沉积速率增加1倍.这两种添加剂的同时使用,使镀层颜色变亮,形貌发生变化.所得镀层是多晶铜,没有发现夹杂Cu2O.     

空心微珠表面化学镀Ni-Co-P合金

以无机非金属粉煤灰空心微珠为芯材, 利用化学镀工艺对其表面进行金属化改性, 可以得到表面完整包覆的导电粉体, 该粉体具有中空, 质轻, 粒度细, 高强度, 耐高温, 导电性能好等多种优异性能, 可部分代替金属和铁氧体微粉作为电磁波吸收剂. 采用SnCl2和PdCl2进行敏化-活化处理后, 在空心微珠表面化学包覆Ni-Co-P合金层, 利用XRD、EDS、SEM和镶嵌金相等方法对样品进行形貌观察和分析表征, 结果表明, 使用PdCl2作活化剂可以得到优质均匀的Ni-Co-P合金镀层, 镀层光亮, 均匀, 包覆完整. 化学镀后镀层呈非晶态, 450 ℃氢气气氛下热处理后出现结晶相Ni3P和六方晶系的α-Co单质.     

表面化学镀对贮氢合金MmNi3.8Co0.5Mn0.4Al0.3性能的影响

在贮氢合金ＭｍＮｉ３．８Ｃｏ０．５Ｍｎ０．４Ａｌ０．３（Ｍｍ为混合希土）粉末表面分别进行化学镀Ｃｕ，Ｃｏ，Ｎｉ，Ｎｉ－Ｃｏ，Ｎｉ－Ｓｎ，Ｎｉ－Ｗ。结果表明不同化学镀对合金贮氢性能有很大影响。     

化学镀镍-钴合金碳纳米管/聚吡咯复合材料的微波吸收性能研究

采用化学镀法在碳纳米管表面均匀地镀覆了磁性镍-钴合金层及采用原位法制备了化学镀镍-钴合金碳纳米管/聚吡咯复合吸波材料。采用XRD、TEM、SEM、FT IR及振动样品磁强计等对碳纳米管镀镍-钴合金层的形貌、微结构与磁性能进行了分析,还采用网络矢量分析仪对该复合材料在3~6 GHz频段内的吸波性能进行了研究。结果表明,镍-钴合金层连续、均匀、完整地包覆在碳纳米管表面,化学镀后镀层呈非晶态。通过在碳纳米管表面镀上磁性金属镍-钴合金层可提升碳纳米管/聚吡咯复合材料的吸波性能,其复合材料最大反射率为-20d B。     

表面活性剂对陶瓷基底化学镀镍的作用机理及镀层性能的影响

采用酸性化学镀技术在Al₂O₃陶瓷片表面沉积Ni-P镀层,通过电感耦合等离子体发射光谱,X射线衍射光谱和扫描电子显微镜等分析测试,对镀层的成分、物相和形貌进行了表征,考察了表面活性剂种类、掺量等因素对镀层表面性貌和性能的影响。结果表明,当添加5 mg·L^-1 SDS时,镀速从14 μm·h^-1增加到17 μm·h^-1,随表面活性剂添加量继续增加,镀速呈减少趋势。添加表面活性剂能够不同程度的消除化学镀Ni-P镀层固有的胞状组织,提高表面致密性和平整性;镀层自腐蚀电流密度从43 μA·cm^-2减小至3.5 μA·cm^-2,镀层的耐腐蚀性能显著提高。根据电化学理论和实验规律,探讨了表面活性剂在化学镀镍磷合金反应过程的影响机理。     

2,2′-联吡啶在化学镀铜中的作用研究

研究了以次磷酸钠作还原剂的化学镀铜体系,添加剂2,2′-联吡啶对化学镀铜沉积速率、次磷酸钠阳极氧化和铜离子阴极还原、以及镀层形貌、结构和组分存在状态的影响.结果表明,2,2′-联吡啶对化学沉积起阻化作用.电化学线性伏安扫描实验显示,镀液中加入2,2′-联吡啶,次磷酸钠的氧化峰电势有所负移,但峰电流减小;铜离子的还原峰电势负移,但峰电流逐渐增大.扫描电子显微镜(SEM)、能量色散谱(EDS)、X射线衍射(XRD)及X射线光电子能谱(XPS)等实验分别表明,添加剂使镀层致密和光亮、镍含量降低;镀层为Cu-Ni合金,呈面心立方结构,无明显晶面择优取向现象;镀层中铜和镍以金属态存在,磷的质量含量小于0.05%.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.