Synthesis of a green-emitting alternating block copolymer

An alternating block copolymer, poly(1,8-octanedioxy-2,6-dimethoxy-1,4-phenylene-1,2-ethenylene-1,4-phenylene-1,2-ethenylene-1,4-phenylene-1,2-ethenylene-3,5-dimethoxy-1,4-phenylene), 1 , was synthesized, and characterized using Fourier transform infrared spectroscopy, nuclear magnetic resonance, gel permeation chromatography differential scanning calorimetry ultraviolet and elemental analysis. Light-emitting single-layer test diodes using this soluble, processible copolymer as the active layer (i.e. indium tin oxide/ 1 /Ca,Al) emit green light with a luminescent spectral maximum at 513 nm. The single-layer device had a brightness of about 80 cd/m² at a current density of 100 mA/cm² with an internal quantum efficiency of 0.3% photon/electron. Optimization of the light-emitting properties of 1 was achieved through variation of a key Wittig polymerization step in the synthesis, using trialkyl rather than triaryl phosphonium salts in an appropriate solvent mixture to achieve nearly regiospecific trans-olefination. This provided an improvement over earlier procedures, which require a post-Wittig isomerization to minimize the presence of electroluminescence-inhibiting cis-bonds. © 1998 John Wiley & Sons, Ltd.     

Syntheses of new poly (arylene vinylene) analogues: Poly (4,7-benzofuran vinylene) and poly (4,7-benzothiophene vinylene)

The reaction of bis(4,7-tetrahydrothiopheniomethyl) benzofuran dibromide with aqueous tetramethylammonium hydroxide leads to a water-soluble polyelectrolyte which can be film cast and thermolytically eliminated to give poly(4,7-benzofuran vinylene) (PBFV). Subjection of bis(4,7-tetrahydrothiopheniomethyl) benzothiophene dibromide to the same reaction sequence gives poly(4,7-benzothiophene vinylene) (PBTV). UV-VIS studies show that PBFV has a band gap of 2.76 eV, while PBTV has a band gap of 2.92 eV. These polymers are members of a new class of conjugated poly (arylene vinylene)s, in which heterocyclic pseudoaromatic rings are fused onto a poly(1,4-phenylene vinylene) backbone. © 1994 John Wiley & Sons, Inc.     

Ultrathin conjugated polymer network films of carbazole functionalized poly(p-phenylenes) via electropolymerization

Ultrathin films of a cross-linked and chemically distinct conjugated poly(p-phenylene) network via electropolymerization are described. The amphiphilic network precursor was synthesized by incorporating the alkoxy carbazole group (-O(CH2)5Cb) to a poly(p-phenylene) (C6PPPOH) backbone. In order to investigate the combined thin film electrochemical and photophysical properties of poly(p-phenylene)s and polycarbazole conjugated polymers, C6PPPC5Cb was deposited on substrates using the Langmuir Blodgett Kuhn (LBK) method. The monolayer isotherm of the polymer, C6PPPC5Cb, showed a liquid expanded region slightly different from the parent polymer C6PPPOH. Multilayers (up to 30 layers) were transferred to different substrates such as quartz, gold coated LaSFN9 and ITO substrates for analysis. For conversion to a conjugated polymer network (CPN) film, the electroactive carbazole group was electropolymerized using cyclic voltammetry (CV) resulting in polycarbazole linking units. The differences in the film properties and corresponding changes in the electrochemical behavior indicate the importance of film thickness and electron/ion transport process in cross linked network films. From the electrochemical studies, the scan rate was found to have a considerable effect on electropolymerization with higher oxidation and reduction peak values found for the rigid network polymer compared to the uncrosslinked polymers.     

Photocurrent generation in multilayer self-assembly films fabricated from water-soluble poly(phenylene vinylene)

A novel, water-soluble, cationic PPV derivative poly[(2,5-bis(3-bromotrimethylammoniopropoxy)-phenylene-1,4-divinylene)-alt-1,4-(2,5-bis(2-(2-hydroxyethoxy)ethoxy))phenylene vinylene] (BH-PPV) has been synthesized by a Heck coupling reaction. Multilayered assemblies of the BH-PPV and the sodium salt of hexa(sulfobutyl)fullerenes (C(60)-HS) were fabricated successfully by an alternate deposition technique. The multilayer structures were studied by UV/Vis spectroscopy, small angle X-ray diffraction, and atomic force microscopy. The photoinduced charge transfer property of the self-assembled multilayer film was also measured by a three-electrode cell technique. A steady and rapid cathodic 5.5 microA cm(-2) photocurrent response was measured as the irradiation of the multilayer film was switched on and off. Importantly, the response of on/off cycling is prompt and reproducible. A possible mechanism for the electron-transfer process is proposed.     

Synthesis and self-assembly of an amphiphilic poly(phenylene ethynylene) ionomer

We have synthesized a conjugated amphiphilic polyelectrolyte, a poly(phenylene ethynylene) (PPE), and the structurally analogous neutral polymer. The solution-phase aggregation of the uncharged PPE can be reversibly controlled by varying the solvent polarity and concentration, while the charged polymer appears to self-assemble at any concentration in compatible solvents. These conclusions are based on a combination of absorption and photoluminescence spectroscopy and dynamic light scattering. Photoinduced absorption spectroscopy was also employed to investigate interchain electronic communication and the photoinduced production of free charge carriers. The uncharged PPE had a relatively high polaron yield, indicating pi-stacking of adjacent PPE chains and efficient exciton splitting, while the charged polymer did not produce polarons, indicating that the polymers are not pi-stacked despite their tendency to form aggregates. This is most likely due to the presence of the cationic trimethylammonium side chains which force neighboring polymer chains too far apart to achieve effective pi-orbital overlap. Polarons were observed in both polymers after chemical doping with iodine. The ability to control aggregation and interchain electronic communication could be a useful tool in designing nanostructured electronic materials.     

Fluorescence blinking, exciton dynamics, and energy transfer domains in single conjugated polymer chains

In order to understand exciton migration and fluorescence intensity fluctuation mechanisms in conjugated polymer single molecules, we studied fluorescence decay dynamics at "on" and "off" fluorescence intensity levels with 20 ps time resolution using MEH-PPV [poly(2-methoxy-5-(2'-ethylhexyloxy)-1,4-phenylenevinylene] dispersed in PMMA. Two types of intensity fluctuations were distinguished for single chains of conjugated polymers. Abrupt intensity fluctuations (blinking) were found to be always accompanied by corresponding changes in fluorescence lifetime. On the contrary, during "smooth" intensity fluctuations no lifetime change was observed. Time-resolved data in combination with data on fluorescence emission and excitation anisotropy lead to a picture where a single polymer molecule is seen as consisting of several energy transfer domains. Exciton migration is efficient within a domain and not efficient between domains. Each domain can have several emitting low-energy sites over which the exciton continuously migrates until it decays. Emission of individual domains is often highly polarized. Fluorescence from a domain can be strongly quenched by Forster energy transfer to a quencher (hole polaron) if the domain overlaps with the quenching sphere.     

Quantum dots tailored with poly(para-phenylene vinylene)

In polymernanoparticle composites, uniform dispersion of the nanoparticles carries advantages over cases where nanoparticle aggregation dominates. Such dispersion has been particularly difficult to obtain in the case of composites prepared from nanoparticles and conjugated polymers. Here, we show that cadmium selenide nanocrystals, or quantum dots, can be integrated into thin films of poly(para-phenylene vinylene) (PPV) without aggregation. The two key departures from previous studies of quantum-dot/electronic polymer composites are (1) the synthesis of high-quality quantum dots directly in novel, functional ligands, thus eliminating the need for ligand exchange, and (2) polymerization chemistry that grafts PPV to the quantum dot surface. Solid-state photoluminescence spectra of composite materials prepared by these novel techniques reveal the critical importance of the quantum dot-polymer interface that will enable new investigations in nanoparticle-based light-emitting devices.     

Anisotropic optical properties in electroluminescent conjugated polymers based on grazing angle photoluminescence measurements

Grazing angle photoluminescence (GPL) originates from a waveguided light emitted at grazing angle to the substrate due to the total internal reflections, and the light emission is polarized with enhanced intensity at selective mode wavelength. GPL measurements reveal the optical anisotropy of luminescent conjugated polymers, in particular, the alignment of emitting dipoles from which emission occurs, in contrast to spectroscopic ellipsometry measurements that give the anisotropy in the absorption. Based on the GPL emission intensities and spectra, we investigate the anisotropic optical properties in electroluminescent poly(9,9'-di-n-octylfluorene-alt-benzothiadiazole) (F8BT) conjugated polymer thin films of different molecular weights (M(n) = 9-255 kg/mol), both in the pristine and annealed states. The optical anisotropy in F8BT films generally increases with molecular weight, suggesting that higher molecular weight polymers with longer chains are more likely to lie in-plane to the substrate. Upon annealing, high molecular weight F8BT films show even a higher degree of anisotropy, in contrast to low molecular weight F8BT films that become more isotropic. Annealing causes the polymer chains to rearrange and adopt a configuration in which the interchain exciton migration to better ordered low energy (LE) emissive states is strongly suppressed. We observe that the emissive states in F8BT are strongly affected by the local polymer chain arrangement, producing the less ordered high energy (HE) emissive states near the substrate interface where there is a higher degree of chain disorder and the LE states in the bulk of the film. When spin coated onto a quartz substrate precoated with a poly(styrenesulfonate)-doped poly(3,4-ethylenedioxythiophene) (PEDOT:PSS) layer, films of F8BT show severe luminescence quenching near the PEDOT:PSS interface for both the LE and HE emissive states, but a selective quenching of the LE states in the bulk of the film. These observations have important implications for fabricating efficient electronic devices using conjugated polymers as an active material, since the performance of these devices will strongly depend on anisotropic optical properties of electroluminescent conjugated polymers.     

Synthesis and characterization of water-soluble poly(p-phenylene vinylene) derivatives via the dithiocarbamate precursor route

Two hydrophilic branched oligo(ethylene glycol)-substituted PPV derivatives, poly(2,5-bis(1,3-bis(triethoxymethoxy)propan-2-yloxy)-1,4-phenylene vinylene) (BTEMP-PPV) and poly(2-methoxy-5-(1,3-bis(triethoxymethoxy)propan-2-yloxy)-1,4-phenylene vinylene) (MTEMP-PPV), are presented. Polymerizations have been performed via the dithiocarbamate precursor route, using lithium hexamethyldisilazide (LHMDS) as a base, to obtain high molecular weight precursor polymers. After thermal conversion of the precursor polymers into the fully conjugated systems, the solubility of the polymers has been examined. The polar nonionic side chains of MTEMP-PPV and BTEMP-PPV render the PPV backbone soluble in a variety of solvents, including alcohols and even water, making these polymers suitable candidates to be used in optoelectronic devices that can be processed from environmentally friendly solvent systems.     

Synthesis and electrical conductivity of poly(arylene vinylene). I. Poly(2,5-dimethoxyphenylene vinylene) and poly(2,5-dimethylphenylene vinylene)

The highly conjugated aromatic polymers, poly(2,5-dimethoxyphenylene vinylene) and poly(2,5-dimethylphenylene vinylene), were obtained from their water soluble, sulfonium salt precursor polymers. Films of these polymers were reacted with either AsF₅ or I₂ vapor. Poly(2,5-dimethoxyphenylene vinylene) showed increases in electrical conductivity of up to 14 to 15 orders of magnitude for these two dopants, while an 8 to 9 order of magnitude increase was observed for poly(2,5-dimethylphenylene vinylene) with the same dopants. The synthesis of the precursor polymers, the properties and elimination reactions of films of the precursors, the doping reactions, and the conductivities of the resulting phenylene vinylene films are discussed.     

Luminescent poly(phenylene vinylene) derivatives with m‐terphenyl or 2,6‐diphenylpyridine kinked segments along the main chain: Synthesis,characterization, and stimulated emission

Two new poly(phenylene vinylene)s containing m‐terphenyl or 2,6‐diphenylpyridine kinked units along the main chain were synthesized and were used as luminescent and laser materials. They were prepared from Heck coupling of 2,5‐didodecyloxy‐1,4‐divinylbenzene with 4,4″‐dibromo‐3′‐phenyl‐m‐terphenyl or 2,6‐di(4‐bromophenyl)‐4‐phenylpyridine. The kinked units along the main chain caused a partial interruption of the conjugation leading to emission at a shorter wavelength as compared with poly(p‐phenylene vinylene). The polymers presented blue‐green emission in solution and green‐yellow emission in the solid state with photoluminescence maxima at 465–497 and 546–550 nm, respectively. Polymer containing 2,6‐diphenylpyridine segments emitted at a longer wavelength than that containing m‐terphenyl and displayed higher quantum yields in solution (0.61 and 0.40, respectively). The influence of the solvent and polymer concentration on the photoluminescence characteristics was investigated. The photoluminescence properties of protonated polymer containing 2,6‐diphenylpyridine segments were investigated both in solution and in film. Amplified spontaneous emission and tunable laser action were also obtained from the two polymers. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2214–2224, 2004     

Dynamics and energetics of the self-assembly of a hydrophobically modified polyelectrolyte: Naphthalene-labeled poly(acrylic acid)

Steady-state and time-resolved fluorescence studies were performed on aqueous solutions of poly(acrylic acid) hydrophobically modified with two very different levels of naphthalene (Np). It is demonstrated that unique information on association phenomena involving hydrophobe-modifed polymers can be obtained from an extended fluorescence study by using data for a less-modified polymer as a reference. For the more highly modified polymer, the presence of excited-state (as well as ground-state) dimers in addition to monomer emission due to locally excited naphthalene gives evidence for hydrophobic association between naphthalene groups. This association becomes, as expected, much less important at higher pH due to the electrostatic repulsion between different chain segments. However, it is noted that even at high pH there is a significant self-association. The coexistence of static and dynamic quenching phenomena of the Np monomer label was also revealed in the time-resolved fluorescence data. The data are compatible with the existence of two types of monomers and one excimer and suggest that the essential contribution to the monomer emission comes from isolated chromophores, whereas excimer formation arises from both a dynamic route (excited Np chromophores able to produce a dynamic excimer) and a static route (excitation of ground-state Np dimers). At room temperature, the dissociative reaction, excimer-to-monomer, can be neglected, and thus the rate constant for excimer formation and decay could be obtained with and without considering the influence of preformed dimers. Temperature has shown to induce different behavior in the polymer photophysics. In the case of the less-labeled polymer, the decays were found to be single-exponential with the fluorescence lifetime decreasing with increasing temperature. From the temperature dependence of the steady-state fluorescence data, the activation energy for excimer formation and the binding energy of the excimer were evaluated at different pH values, through the Stevens-Ban-type plots of the excimer-to-monomer intensity ratio. With the time-resolved data, measured in the temperature range of 5-60 degrees C, it was possible to extract the intrinsic activation energies for excimer formation. The thermodynamic driving force for the intrapolymeric association was found to be dependent on a balance between hydrophobic and electrostatic interactions, which are dependent on the pH, temperature, and hydrophobic content of the polymer.     

Modeling the growth and molecular structure of conductive polymers: Application to poly(dialkoxybenzene)s

A modeling strategy, based on (i) quantum semiempirical calculation of the electronic structure of the successive intermediate oligomers and (ii) evaluation of the activation energy of the successive coupling reactions by use of the frontier orbital model, has been used to study the growth of a wide set of conductive polymers and is illustrated with poly(1,2-dialkoxybenzene) and poly(1,4-dialkoxybenzene) generated by electrochemical oxidation of the corresponding monomer. These monomers have been chosen because they are known to yield polymers of completely different structures. The strategy, which is designed to be as little computer time-consuming as possible, allows us to predict a growth trend in agreement with the structure inferred from spectrochemical experiments. In the case of poly(1,2-dialkoxybenzene) it suggests the formation of a cyclic tetramer as a byproduct detected in small quantities by means of MALDI spectroscopy. This modeling strategy allows one to describe the electronic modifications induced by the growth of a highly conjugated structure. It suggests that oxidation of the successive oligomers at high doping level and quinonic deformation are key factors for the growth of long and regular polymer structures     

Synthesis of conjugated polymers containing anthracene moiety and their electro‐optical properties

Both fully conjugated polymer poly[2‐methoxy‐5‐(2‐ethylhexyloxy)‐1,4‐phenylene vinylene‐alt‐9,10‐anthrylene vinylene] [poly(MEHPV‐AV)] and conjugated/nonconjugated block copolymers poly(alkanedioxy‐2‐methoxy‐1,4‐phenylene‐1,2‐ethenylene‐9,10‐anthrylene‐1,2‐ehthenylene‐3‐methoxy‐1,4‐phenylene)[poly(BFMPx‐AV), (x = 4, 8, and 12)] were synthesized by Horner–Emmons reaction utilizing potassium tert‐butoxide. Of these synthesized polymers poly(BFMP4‐AV) and poly(BFMP8‐AV), which has four and six methylene groups as solubility spacer in the main chain exhibited liquid crystalline to isotropic transition in addition to the two first order transitions. Light‐emitting diode (LED)s made from the organic solvent soluble poly(BFMP12‐AV) as emitting layer showed blue shift in the emission spectrum compared to the one made from fully conjugated poly(MEHPV‐AV). Although poly(BFMP12‐AV) had higher barrier to the electron injection from cathode than poly(MEHPV‐AV), the luminance efficiency of LED made from poly(BFMP12‐AV) was about 25 times higher than the one made from poly(MEHPV‐AV), which had fully conjugated structure. LEDs fabricated by both poly(BFMP12‐AV) and poly(MEHPV‐AV) exhibited Stoke's shift in the range of 155 to 168 nm from the absorption maximum due to the excimer formation between the ground and excited state anthracene groups. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 3173–3180, 2000     

PREPARATION AND CHARACTERIZATION OF SHISH-KEBAB TYPE LIQUID CRYSTALLINE POLY（p-PHENYLENEVINYLENE）

Novel shish-kebab type liquid crystalline poly（p-phenylenevinylene） derivatives were synthesized by Stille coupling reaction from 2,5-bis[（4-n-alkoxyl）benzoyloxy]1,4-dibromobenzene （monomer l） and 1,2-bis（tributylstannyl） ethylene （monomer 2）. The polymers with alkoxy groups are soluble in common organic solvents and exhibit blue fluorescence. Both the cast film and the annealed film have large red-shifts in fluorescence spectra and show yellow fluorescence. The polymers with CN and NO2 groups show poor solubility and green fluorescence. All the polymers possess liquid crystalline smectic phases. The melting point （Tm） of the polymers decreases when the length of the alkoxy tails of the mesogenic units increases. The polymers are easily aligned under a magnetic field of 10 Tesla. It is found that the conjugated backbone and LC side chain are aligned perpendicular and parallel to the magnetic field, respectively. The polymers show optical dichroism in fluorescence spectra, suggesting that they are available for advance materials with linear optical polarization.     

Photophysical properties of hydroxylated amphiphilic poly(p-phenylene)s

A homologous series of polyhydroxylated poly(p-phenylene)s with different alkoxy groups (C6PPPOH, C12PPPOH, and C18PPPOH) were synthesized with use of the Suzuki polycondensation reaction. Comparative studies of the structure correlation between their photophysical properties and film morphology is described. The absorption and emission spectra of polymers in solution and thin films showed similar features indicating that the electronic properties in solution were retained in the film state. Compared to the polymer with the short alkoxy chains (C6PPPOH), the polymers with long alkoxy groups (C12PPPOH and C18PPPOH) showed improved film forming properties with continuous and smooth film morphology. The absorption properties of the C12PPPOH showed an enhanced effective conjugation length and high quantum yield implying planarization of the backbone through alkoxy chain packing (C12H25O-) and potential hydrogen bonds. No overlap in the absorption and emission spectra was observed, which indicated minimized excimer formation or excitation energy transfer in the films. Time-resolved fluorescence measurements showed that the decay times increased from 43 ps (C6PPPOH) to 78 ps (C12PPPOH) and 99 ps (C18PPPOH). Electrochemical studies were performed for all polymers and the observed oxidation potential for C6PPPOH was higher than that of C12PPPOH and C18PPPOH. In addition, the C12PPPOH has the lowest band gap of DeltaE = 2.59 eV when compared to the 3.1 (C6PPPOH) and 2.61 eV (C18PPPOH) gaps. The optical band gaps estimated from the absorption onset of the polymers are significantly higher than those obtained from electrochemical data. C12PPPOH was chosen for investigating the charge carrier mobility by the time-of-flight (TOF) technique. The observed results also showed negative field dependent values of the drift mobility for the polymer C12PPPOH.     

Conjugation enhancement of intramolecular exciton migration in poly(p-phenylene ethynylene)s

Efficient energy migration in conjugated polymers is critical to their performance in photovoltaic, display, and sensor devices. The ability to precisely control the polymer conformation is a key issue for the experimental investigations and deeper understanding of the nature of this process. We make use of specially designed iptycene-containing poly(p-phenylene ethynylene)s that display chain-extended conformations when dissolved in nematic liquid crystalline solvents. In these solutions, the polymers show a substantial enhancement in the intrachain exciton migration rate, which is attributed to their increased conjugation length and better alignment. The organizational enhancement of the energy transfer efficiency, as determined by site-selective emission from lower energy traps at the polymer termini, is accompanied by a significant increase of the fluorescence quantum yield. The liquid crystalline phase is a necessary requirement for these phenomena to occur, and when the temperature was increased above the nematic-isotropic transition, we observed a dramatic reduction of the energy transfer efficiency and fluorescence quantum yield. The ability to improve the exciton migration efficiency through precise control of the polymer structure with liquid crystalline solutions demonstrates the importance of a polymer's conformation for energy transfer, and provides a way to improve the energy transporting performance of conjugated polymers.     

Steric effects on excimer formation in isotactic and atactic polystyrene and poly(ar-methylstyrene)s in solution

Effects of tacticity and steric hindrance on excimer formation were investigated in isotactic and atactic polystyrene, poly(o-methylstyrene), poly(m-methylstyrene), and poly(p-methylstyrene) in the presence and absence of a quencher (CCl₄). The calculated rate constants for excimer formation in the isotactic polymers except for poly(o-methylstyrene) were almost the same and larger than those in the corresponding atactic polymers. These results indicate that excimer formation was due to not only rotational sampling but also energy migration to trapping sites. It was found that steric hindrance on excimer formation was intimately related to the excition diffusion length in the polymer chain.     

Synthesis and characterization of highly hindered and thermally stable poly(1,4‐spirobifluorenylenevinylene) derivative

A new poly(1,4‐spirobifluorenylenevinylene) having advantage PPV and spirobifluorene as new emissive family was synthesized. Compared with PPV derivatives that usually have a tolane bisbenzyl defect, the polymer has the defect free structure because of the steric hindrance of the asymmetric bulky spirobifluorenyl group. Compared with spirobifluorene derivatives that usually have a low solubility, the polymer has the good solubility in common organic solvents. The polymer was amorphous and showed high PL quantum efficiency and high thermal stability with high T_g. The PL emission peaks were shown at 480–490 nm in solution and film, respectively, which may represent the bluest emission peak reported for fully conjugated PPV derivatives. The study of thermal annealing of PL spectrum showed excimer formation inhibited. The thermal and optoelectronic properties of the polymer imply that it is a promising material for the PLED application. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 900–907, 2007.     

The use of poly(alkylene oxide)s to achieve fast and controlled photochromic switching in rigid matrices

We report a conjugation system for the enhancement of photochromic dye performance in rigid matrices using widely available, cheap, chemically robust and compatible polymeric starting materials, namely poly(propylene oxide) (PPO) and poly(1,2‐butylene oxide). Conjugation of these soft (low T_g) polymers to an indeno‐fused naphthopyran photochromic dye, in a telechelic geometry, gives access to a wide range of accelerated and tuned fade speeds (decoloration) via variation in molecular weight. The t_1/2 and t_3/4 fade speeds for PPO conjugates (polymer molecular weights ranging between ca. 425 and 2000) are accelerated by 35–58 and 51–76%, respectively, compared with the nonconjugated control dye. Longer oligomers provide faster decoloration approaching that obtained in solution. The stability of the polyethers allows functionalization using a wide variety of chemistries, including harsh acid catalyzed transformations, providing an overall facile synthesis of photochromic dye‐polymer conjugates in high yield and purity. In addition, these polymers give easy access to conjugates with star‐type architectures, which provide an even further improvement in performance compared with their linear counterparts with less conjugated polymer needed per dye to achieve a given fade speed. © 2012 Commonwealth of Australia. J Polym Sci Part A: Polym Chem, 2012