Sensitivity Enhancement in Nickel Hydroxide/3D‐Graphene as Enzymeless Glucose Detection

A nickel hydroxide (Ni(OH)₂)/3D‐graphene composite is used as monolithic free‐standing electrode for enzymeless electrochemical detection of glucose. Ni(OH)₂ nanoflakes are synthesized by using a simple solution growth procedure on 3D‐graphene foam which was grown by chemical vapor deposition (CVD). The pore structure of 3D‐graphene allows easy access to glucose with high surface area, which leads to glucose detection with an ultrahigh sensitivity of 3.49 mA mM^?1 cm^?2 and a significant lower detection limit up to 24 nM. Cyclic voltammetry (CV) and potentionstatic mode is used for non‐enzymatic glucose sensing. The impedance and effective surface area have been studied well. The high sensitivity, low detection limit and simple configuration of Ni(OH)₂/three dimensional (3D)‐graphene composite electrodes can evoke its industrial application in glucose sensing devices.     

Sensitive Electrochemical Aptasensor for Thrombin Detection with Platinum Nanoparticles,Blocking Reagent‐Horseradish Peroxidase and Graphene Oxide as Enhancers

A highly sensitive thrombin electrochemical aptasensor with Pt nanoparticles, blocking reagent‐horseradish peroxidase (HRP) and inert graphene oxide (GO) as enhancers was successfully fabricated. Firstly, Pt nanoparticles with high surface to volume ratio could increase the amount of the immobilized redox probe hexacyanoferrate nanoparticles (NiHCFNPs) and effectively enhance the electron transfer. Secondly, HRP and Pt nanoparticles with high catalytic activity extremely amplify the electrochemical signal of NiHCFNPs toward H₂O₂. Lastly, inert graphene oxide (GO) labeled TBA could be used for enlarging the steric hindrance of thrombin. As a result, the aptasensor showed a high sensitivity with a detection limit of 500 fM.     

Iridium‐Catalyst‐Based Autonomous Bubble‐Propelled Graphene Micromotors with Ultralow Catalyst Loading

A novel concept of an iridium‐based bubble‐propelled Janus‐particle‐type graphene micromotor with very high surface area and with very low catalyst loading is described. The low loading of Ir catalyst (0.54 at %) allows for fast motion of graphene microparticles with high surface area of 316.2 m² g^?1. The micromotor was prepared with a simple and scalable method by thermal exfoliation of iridium‐doped graphite oxide precursor composite in hydrogen atmosphere. Oxygen bubbles generated from the decomposition of hydrogen peroxide at the iridium catalytic sites provide robust propulsion thrust for the graphene micromotor. The high surface area and low iridium catalyst loading of the bubble‐propelled graphene motors offer great possibilities for dramatically enhanced cargo delivery.     

Determination of Xenoestrogenic Compounds Using a Nanostructured Biosensing Device

A ternary composite material based on Prussian blue, single‐walled carbon nanotubes and 1‐butyl‐3‐methylimidazolium hexafluorophosphate was prepared and tested for electrochemical detection of H₂O₂. The sensor allows amperometric detection of H₂O₂ at ?0.05 V, with a sensitivity of 137 mA M^?1?cm^?2. The nanocomposite provides a favorable microenvironment for immobilization of horseradish peroxidase (HRP). Determination of xenoestrogenic compounds was performed by enzymatic oxidation at the surface of modified screen printed biosensor in the presence of H₂O₂. The developed electrochemical biosensors exhibited high sensitivity, low detection limits, good operational and storage stability, for detection of 4‐t‐butylphenol, 4‐t‐octylphenol, 4‐n‐nonylphenol and 4‐n‐nonylphenol ethoxylate.     

Synergistic Enhancement of Electrocatalytic Activity toward Oxygen Reduction Reaction in Alkaline Electrolytes with Pentabasic (Fe,B, N,S, P)‐Doped Reduced Graphene Oxide

As alternatives to Pt‐based electrocatalysts, the development of nonprecious metal catalysts with high performance in the cathodic oxygen reduction reaction (ORR) is highly desirable for widespread use in fuel cells. Here we report a simple approach for preparing pentabasic (Fe, B, N, S, P)‐doped reduced graphene oxide (rGO) via a two‐step doping method of adding boric acid and ferric chloride to ternary (N, S, P)‐doped rGO (NSPG). Electrochemical investigation of the composites for the ORR revealed that simultaneously doping appropriate amounts of Fe and B into the NSPG produced a synergistic effect that endowed the prepared catalyst with both a positively shifted ORR half‐wave potential and high selectivity for the 4e^? reduction of O₂. The optimized Fe₂B‐NSPG catalyst approached a 4e^? process for the ORR with a half‐wave potential (E_1/2=0.90 V vs. RHE) even 30 mV higher than that of the commercial Pt/C catalyst in alkaline solution. Furthermore, relative to the Pt/C catalyst, the Fe₂B‐NSPG demonstrated superior stability and excellent tolerance of the methanol cross‐over effect. This simple method afforded pentabasic (Fe, B, N, S, P)‐doped rGO as a promising nonprecious metal catalyst used for alkaline fuel cells.     

Enhanced Peroxidase‐Like Properties of Graphene–Hemin‐Composite Decorated with Au Nanoflowers as Electrochemical Aptamer Biosensor for the Detection of K562 Leukemia Cancer Cells

Graphene composites with hemin and gold nanoparticles show a better performance for hydrogen peroxide decomposition compared to that of the three components alone or duplex/hybrid complexes. Our previous studies showed that the morphology of the Au nanoparticles may greatly influence the catalytic activity of graphene‐family peroxidase mimics. Recently, we found that Au nanoflowers could grow in situ and form on the surface of hemin/RGO (reduced graphene oxide). The prickly morphology of this Au nanoflower brought a higher catalytic ability with enhanced kinetic parameters than traditional Au nanoparticles that showed a smooth surface. Therefore, based on this discovery, a smart electrochemical aptamer biosensor for K562 leukemia cancer cells was further presented with good performance in selectivity and sensitivity attributed to the excellent mimetic peroxidase catalytic activity of this newly synthesized Au nanoflower decorated graphene–hemin composite (H‐RGO‐Au NFs).     

Bifunctional Reduced Graphene Oxide/V2O5 Composite Hydrogel: Fabrication,High Performance as Electromagnetic Wave Absorbent and Supercapacitor

Multifunctional graphene hydrogels have attracted great attention aimed at practical applications. Herein, the novel and bifunctional composite hydrogel containing reduced graphene‐oxide nanosheets (RGO) and V₂O₅ nanobelts (RGO/V₂O₅) is successfully prepared for the first time. Surprisingly, tridimensional (3D) RGO/V₂O₅ composite hydrogels cannot only be used as high‐performance electromagnetic (EM) wave absorbents; they also exhibit excellent properties suitable for supercapacitor electrodes. The composites exhibit a maximum absorption of up to ?21.5 dB. In particular, a composite hydrogel showed a bandwidth of 6.63 GHz, corresponding to a reflection loss at ?10 dB, which opens the possibility for the use of 3D graphene with other functional nanomaterials as lightweight and high‐performance EM wave absorption materials. Remarkably, the composite hydrogel is capable of delivering a high specific capacitance of about 320 F g^?1 at a current density of 1.0 A g^?1.     

Graphene and Nanogold‐Functionalized Immunosensing Interface with Enhanced Sensitivity for One‐Step Electrochemical Immunoassay of Alpha‐Fetoprotein in Human Serum

A new electrochemical immunosensing protocol for sensitive detection of alpha‐fetoprotein (AFP, as a model) in human serum was developed by means of immobilization of horseradish peroxidase‐anti‐AFP conjugates (HRP‐anti‐AFP) onto graphene and nanogold‐functionalized biomimetic interfaces. The low‐toxic and high‐conductive graphene complex provided a large capacity for nanoparticulate immobilization and a facile pathway for electron transfer. With a one‐step immunoassay format, the antigen‐antibody complex was formed between the immobilized HRP‐anti‐AFP on the electrode and AFP in the sample. The formed immunocomplex was coated on the electrode surface, inhibited partly the active center of HRP, and decreased the catalytic reduction of HRP toward the enzyme substrate of H₂O₂. Under optimal conditions, the decrease of reduction currents was proportional to AFP concentration, and the dynamic range was 1.0–10 ng/mL with a relative‐low detection limit (LOD) of 0.7 ng/mL AFP. Intra‐ and inter‐assay coefficients of variation (CVs) were less than 10 %. The assay was evaluated for clinical human serum samples, including 8 (possible) patients with hepatocarcinoma and 3 normal human sera. Correct identification of negative/positive samples and perfect accordance with results from Elecsys 2010 Electrochemiluminescent Automatic Analyzer as a reference was obtained. Importantly, the graphene and nanogold‐based sensor provided a promising platform for the detection of other biocompounds, and could be further applied for development of other potential electrochemical bio/chemosensors.     

A study of novel macrocyclic copper complex/graphene‐based composite materials for counter electrodes of dye‐sensitized solar cells

In this study, a newly synthesized macrocyclic copper complex, [Cu(C₁₀H₂₀N₈)(C₄H₈N₄)](BF₄)₂, was used for a reaction with graphene oxide. Macrocyclic copper complex/graphene‐based composite materials were prepared and applied to the counter electrodes (CEs) of dye‐sensitized solar cells (DSSCs). As the level of the macrocyclic copper complex increased, the catalytic sites on the surface of the CE increased. The results showed that the device efficiency of the composite GO/Cu (1:10) CE was 7.61%, which was better than that of the Platinum (Pt) CE (7.04%). The device efficiency of the DSSC was enhanced effectively because the electrocatalytic activity of the CE was enhanced, and the interface impedance of the device was reduced. Therefore, the macrocyclic copper complex/graphene‐based composite materials may have the potential to replace traditional Pt to increase efficiency and reduce the fabrication cost of DSSCs.     

Enhanced Electrocatalytic Performance of a Porous g‐C3N4/Graphene Composite as a Counter Electrode for Dye‐Sensitized Solar Cells

A porous graphitic carbon nitride (g‐C₃N₄)/graphene composite was prepared by a simple hydrothermal method and explored as the counter electrode of dye‐sensitized solar cells (DSCs). The obtained g‐C₃N₄/graphene composite was characterized by XRD, SEM, TEM, FTIR spectroscopy, and X‐ray photoelectron spectroscopy. The results show that incorporating graphene nanosheets into g‐C₃N₄ forms a three‐dimensional architecture with a high surface area, porous structure, efficient electron‐transport network, and fast charge‐transfer kinetics at the g‐C₃N₄/graphene interfaces. These properties result in more electrocatalytic active sites and facilitate electrolyte diffusion and electron transport in the porous framework. As a result, the as‐prepared porous g‐C₃N₄/graphene composite exhibits an excellent electrocatalytic activity. In I^?/I₃^? redox electrolyte, the charge‐transfer resistance of the porous g‐C₃N₄/graphene composite electrode is 1.8 Ω cm², which is much lower than those of individual g‐C₃N₄ (70.1 Ω cm²) and graphene (32.4 Ω cm²) electrodes. This enhanced electrocatalytic performance is beneficial for improving the photovoltaic performance of DSCs. By employing the porous g‐C₃N₄/graphene composite as the counter electrode, the DSC achieves a conversion efficiency of 7.13 %. This efficiency is comparable to 7.37 % for a cell with a platinum counter electrode.     

Palladium Nanoparticles Embedded into Graphene Nanosheets: Preparation,Characterization, and Nonenzymatic Electrochemical Detection of H2O2

A novel nonenzymatic H₂O₂ sensor based on a palladium nanoparticles/graphene (Pd‐NPs/GN) hybrid nanostructures composite film modified glassy carbon electrode (GCE) was reported. The composites of graphene (GN) decorated with Pd nanoparticles have been prepared by simultaneously reducing graphite oxide (GO) and K₂PdCl₄ in one pot. The Pd‐NPs were intended to enlarge the interplanar spacing of graphene nanosheets and were well dispersed on the surface or completely embedded into few‐layer GN, which maintain their high surface area and prevent GN from aggregating. XPS analysis indicated that the surface Pd atoms are negatively charged, favoring the reduction process of H₂O₂. Moreover, the Pd‐NPs/GN/GCE could remarkably decrease the overpotential and enhance the electron‐transfer rate due to the good contact between Pd‐NPs and GN sheets, and Pd‐NPs have high catalytical effect for H₂O₂ reduction. Amperometric measurements allow observation of the electrochemical reduction of H₂O₂ at 0.5 V (vs. Ag/AgCl). The H₂O₂ reduction current is linear to its concentration in the range from 1×10^?9 to 2×10^?3 M, and the detection limit was found to be 2×10^?10 M (S/N=3). The as‐prepared nonenzymatic H₂O₂ sensor exhibits excellent repeatability, selectivity and long‐term stability.     

Label‐free Electrochemical Aptasensor for Carcino‐embryonic Antigen Based on Ternary Nanocomposite of Gold Nanoparticles,Hemin and Graphene

In this report, a label‐free electrochemical aptasensor for carcino‐embryonic antigen (CEA) was successfully developed based on a ternary nanocomposite of gold nanoparticles, hemin and graphene nanosheets (AuNPs‐HGNs). This nanocomposite was prepared by decorating gold nanoparticles on the surface of hemin functionalized graphene nanosheets via a simple wet‐chemical strategy. The aptamer can be assembled on the surface of AuNPs‐HGNs/GCE (glassy carbon electrode) through Au‐S covalent bond to form the sensing interface. Hemin absorbed on the graphene nanosheets not only acts as a protective agent of graphene sheets, but also as an in situ probe base on its excellent redox properties. Gold nanoparticles provide with both numerous binding sites for loading CEA binding aptamer (CBA) and good conductivity to promote the electron transfer. The current changes, which are caused by CEA specifically binding on the modified electrode, are exploited for the label‐free detection of CEA in a very rapid and convenient protocol. Therefore, the method has advantages of high sensitivity, wide linear range (0.0001–10 ng mL^?1), low detection limit (40 fg mL^?1) and attractive specificity. The results illustrate that the proposed label‐free electrochemical aptasensor has a potential application in the biological or clinical target analysis for its simple operation and low cost.     

An intimately bonded titanate nanotube–polyaniline–gold nanoparticle ternary composite as a scaffold for electrochemical enzyme biosensors

In this work, titanate nanotubes (TNTs), polyaniline (PANI) and gold nanoparticles (GNPs) were assembled to form a ternary composite, which was then applied on an electrode as a scaffold of an electrochemical enzyme biosensor. The scaffold was constructed by oxidatively polymerising aniline to produce an emeraldine salt of PANI on TNTs, followed by gold nanoparticle deposition. A novel aspect of this scaffold lies in the use of the emeraldine salt of PANI as a molecular wire between TNTs and GNPs. Using horseradish peroxidase (HRP) as a model enzyme, voltammetric results demonstrated that direct electron transfer of HRP was achieved at both TNT-PANI and TNT-PANI-GNP-modified electrodes. More significantly, the catalytic reduction current of H₂O₂ by HRP was ∼75% enhanced at the TNT-PANI-GNP-modified electrode, compared to that at the TNT-PANI-modified electrode. The heterogeneous electron transfer rate constant of HRP was found to be ∼3 times larger at the TNT-PANI-GNP-modified electrode than that at the TNT-PANI-modified electrode. Based on chronoamperometric detection of H₂O₂, a linear range from 1 to 1200 μM, a sensitivity of 22.7 μA mM⁻¹ and a detection limit of 0.13 μM were obtained at the TNT-PANI-GNP-modified electrode. The performance of the biosensor can be ascribed to the superior synergistic properties of the ternary composite.     

MoS2 Nanosheets Supported on 3D Graphene Aerogel as a Highly Efficient Catalyst for Hydrogen Evolution

The development of efficient catalysts for electrochemical hydrogen evolution is essential for energy conversion technologies. Molybdenum disulfide (MoS₂) has emerged as a promising electrocatalyst for hydrogen evolution reaction, and its performance greatly depends on its exposed edge sites and conductivity. Layered MoS₂ nanosheets supported on a 3D graphene aerogel network (GA‐MoS₂) exhibit significant catalytic activity in hydrogen evolution. The GA‐MoS₂ composite displays a unique 3D architecture with large active surface areas, leading to high catalytic performance with low overpotential, high current density, and good stability.     

Graphene Quantum Dots Assembled with Metalloporphyrins for “Turn on” Sensing of Hydrogen Peroxide and Glucose

Noncovalent and multifunctional hybrids have been generated via π–π stacking and electrostatic interactions by combining the nanometer‐scale graphene structure of graphene quantum dots (GQDs) with Fe^III 5,10,15,20‐tetrakis(1‐methyl‐4‐pyridyl)porphine (FeTMPyP). The inner filter effect (IFE) of FeTMPyP on the GQDs results in substantial PL quenching of the GQDs. The quenched PL of GQDs by the FeTMPyP can be switched back “on” in response to the reaction between FeTMPyP and H₂O₂, which causes rupture of the cyclic tetrapyrrolic nucleus with consequential loss of iron from FeTMPyP, and then proceeds further to produce colorless dipyrroles and monopyrroles. This “turn on” system can be applied for simple and convenient H₂O₂ sensing and can be further extended to the detection of glucose in combination with the specific catalytic effect of glucose oxidase (GOx) through the oxidation of glucose and formation of H₂O₂. Because of the inherent synthetic control available for the design of metalloporphyrins, the GQDs‐based optical sensing approach described here has the potential to be highly versatile for other target analytes.     

Construction of a 2D Graphene‐Like MoS2/C3N4 Heterojunction with Enhanced Visible‐Light Photocatalytic Activity and Photoelectrochemical Activity

A novel graphene‐like MoS₂/C₃N₄ (GL‐MoS₂/C₃N₄) composite photocatalyst has been synthesized by a facile ethylene glycol (EG)‐assisted solvothermal method. The structure and morphology of this GL‐MoS₂/C₃N₄ photocatalyst have been investigated by a wide range of characterization methods. The results showed that GL‐MoS₂ was uniformly distributed on the surface of GL‐C₃N₄ forming a heterostructure. The obtained composite exhibited strong absorbing ability in the ultraviolet (UV) and visible regions. When irradiated with visible light, the composite photocatalyst showed high activity superior to those of the respective individual components GL‐MoS₂ and GL‐C₃N₄ in the degradation of methyl orange. The enhanced photocatalytic activity of the composite may be attributed to the efficient separation of electron–hole pairs as a result of the matching band potentials between GL‐MoS₂ and GL‐C₃N₄. Furthermore, a photocatalytic mechanism for the composite material has been proposed, and the photocatalytic reaction kinetics has been measured. Moreover, GL‐MoS₂/C₃N₄ could serve as a novel sensor for trace amounts of Cu²⁺ since it exhibited good selectivity for Cu²⁺ detection in water.     

Tunable Catalytic Performance and Selectivity of a Nanoparticle–Graphene Composite through Finely Controlled Nanoparticle Loading

Graphene‐based composites offer enhanced catalytic performance of metal and semiconductor nanoparticles, but their development is challenging because catalytic performance strongly depends on the structure and composition of the composite. Herein we show that the catalytic performance of a nanoparticle–graphene composite is very dependent on catalyst loading, which can be optimized for simultaneous enhancement of activity and selectivity. A glassy carbon working electrode has been modified with a gold nanoparticle–graphene (Au–G) composite with a varied number of gold nanoparticles per graphene, so that the conducting property of graphene and the electrocatalytic property of the metal were effectively coupled to give the best catalytic activity and selectivity. The modified electrode was used for simultaneous electrochemical detection of a mixture of electroactive species with high sensitivity. This result shows that the catalytic performance of a graphene‐based composite is sensitive to the catalyst loading and should be optimized for the best performance.     

Alumina nanoflake‐coated graphene nanohybrid as a novel flame retardant filler for polypropylene

γ‐Al₂O₃ nanoflakes are decorated on the surface of graphene nanosheets by hydrothermal method. The chemical structures, composition, and morphology of the graphene nanohybrid are characterized. Alumina nanoflake‐coated graphene nanohybrid is incorporated into polypropylene (PP) matrix by master batch‐based melt mixing method. The effects of alumina‐graphene nanohybrid on the thermal stability and combustion behavior of PP are investigated. More char residue is left for PP composite containing alumina‐graphene nanohybrid. Peak heat release rate of pure PP is greatly decreased by this nanohybrid, corresponding to 30.6% reduction. Fire safety of PP is considerably enhanced. Flame retardant mechanisms are concluded based on the combustion results and char analysis. The barrier effect of graphene and catalytic charring actions of γ‐Al₂O₃ nanoflakes make the contribution to the enhanced flame retardant properties.     

Photoelectrochemical Detection of H2O2 Based on Flower‐Like CuInS2‐Graphene Hybrid

A novel photoelectrochemcial biosensing system was fabricated based on the composition of horseradish peroxidase (HRP), flower‐like CuInS₂ (CIS) and graphene on indium tin oxide (ITO) electrode for detecting H₂O₂. The graphene layer was used as highly conductive scaffolds for electron transport from the ITO electrode to CIS. Furthermore, the flower‐like CIS enhanced the multi‐reflection of light and provided matrixes for the adsorption of HRP. Utilizing one‐pot solvothermal method, we prepared flower‐like CIS‐graphene hybrid (GCIS). Electrochemical tests displayed advantage of graphene with better electron conductivity, and HRP/GCIS showed higher photoelectrochemical behavior.     

Polystyrene/graphene composite electrode fabricated by in situ polymerization for capillary electrophoretic determination of bioactive constituents in Herba Houttuyniae

A novel graphene/polystyrene composite electrode was developed for the enhanced amperometric detection of CE in this work. The composite electrode was fabricated on the basis of the in situ polymerization of a mixture of graphene and prepolymerized styrene in the bore of a piece of fused‐silica capillary under heat. SEM, XRD, and FTIR offered insights into the nature of the composite. The results indicated that graphenes were well dispersed and embedded throughout the PS matrix to form an interconnected conducting network. The performance of this unique graphene‐based detector has been demonstrated by separating and detecting rutin, isoquercitrin, quercitrin, and chlorogenic acid in Herba Houttuyniae (a traditional Chinese medicine) in combination with CE. The prepared graphene‐based CE detector offered significantly lower detection potential, yielded enhanced signal‐to‐noise characteristics, and exhibited high resistance to surface fouling and enhanced stability. It showed long‐term stability and reproducibility with a relative standard deviation of 3.1% for the peak current (n=15).