氧化石墨及石墨烯对阳离子染料的吸附行为研究

利用改进的Hummers-Offeman法合成氧化石墨(GO)和石墨烯,并以其作为吸附剂,选择三种阳离子染料为模型染料,通过测定吸附前后三种阳离子染料溶液的紫外-可见吸收光谱,考察pH、染料初始浓度、温度对吸附效果的影响,研究GO及石墨烯对这三种阳离子染料的吸附行为。结果表明,GO及石墨烯对三种阳离子染料的吸附过程均符合准二级反应动力学方程,且染料结构和pH对其吸附效率也有影响。     

复合改性膨胀石墨的制备及对酸性艳蓝染料的吸附

采用相同反离子协同磷酸活化法, 以十六烷基三甲基溴化铵(CTAB)-KBr为复合改性剂, 制备了一种高效吸附剂复合改性膨胀石墨(M-EG), 通过扫描电子显微镜(SEM)、 傅里叶变换红外光谱(FTIR)及X射线电子能谱(XPS)等对膨胀石墨(EG)和改性膨胀石墨(M-EG)的形貌结构、 组成和价态进行了表征, 考察了EG和M-EG对酸性艳蓝染料废水的处理效果. 结果表明, 复合改性后的膨胀石墨孔隙度变大, 表面含氮和溴官能团增多. 吸附剂M-EG对酸性艳蓝染料废水具有较高的吸附性能, 在pH=1.0及30 ℃条件下对染料的去除率达到94.13%; EG符合二级动力学吸附模型, 用Langmuir等温线方程拟合效果较好; M-EG符合二级吸附动力学方程, 同时符合Langmuir和Freundlich等温吸附模型; M-EG的吸附动力学常数大于EG吸附动力学常数.     

Ni-MOFs@GO复合材料吸附亚甲基蓝工艺优化及其性能研究

为了提高氧化石墨烯(GO)对阳离子染料的吸附效果,采用溶液共混法制备Ni-MOFs@GO复合材料。采用X射线衍射仪(XRD)、傅里叶红外光谱仪(FTIR)和扫描电子显微镜(SEM)对其结构和形貌进行了表征。采用响应曲面法(RSM)优化Ni-MOFs@GO对亚甲基蓝(MB)的吸附工艺。以Ni-MOFs@GO浓度、MB质量浓度和吸附温度3因素为变量,以MB吸附量为响应值,建立了二项式回归模型方程,确定最佳吸附条件,并进行动力学和热力学分析。结果表明：3因素的一次项和二次项对MB的吸附效果影响显著,交互项影响不明显。Ni-MOFs@GO对MB最佳吸附条件为Ni-MOFs@GO浓度为0.6 g·L^-1,MB质量浓度为30 mg·L^-1,吸附温度为26℃,MB吸附量为259.83 mg/g;吸附过程符合准二级动力学方程,吸附模型符合Freundlich等温线方程。     

羧基化石墨烯对4种离子型染料的吸附脱色

合成的羧基化石墨烯（G-COOH）用FT-IR进行表征,并对G-COOH用于水溶液中甲基紫、中性红、灿烂黄和茜素红4种离子型染料的吸附性能进行了研究。 考察了吸附剂用量、吸附时间、初始浓度以及溶液pH值等条件对吸附效果的影响。 同时,研究了甲基紫染料的脱附性能,结果表明,用NaOH/EtOH混合溶液洗脱甲基紫,洗脱率可达88.2%,洗脱后的G-COOH可再利用。 从热力学角度探讨得出,G-COOH对阳离子染料甲基紫和中性红的吸附行为能够较好的符合Langmuir等温吸附模型,而对阴离子染料灿烂黄和茜素红的吸附行为则能够较好的符合Freundlich等温吸附模型,计算的吸附参数表明,G-COOH对4种染料的吸附过程容易进行。 动力学研究表明,G-COOH对4种离子型染料的吸附行为均能较好的符合准二级吸附模型。 该实验研究表明,在处理染料废水时,G-COOH为相当优异的吸附剂。     

具有超高阳离子染料去除能力的磺酸功能化球形共价有机框架

通过三醛基间苯三酚(TFP)与2,2′-联苯胺二磺酸(BDSA)的席夫碱反应, 合成了β-酮烯胺连接的磺酸功能化球形共价有机框架(TFP-BDSA COF). 所得阴离子型TFP-BDSA可迅速吸附如亚甲基蓝(MLB)、 结晶紫(CV)和罗丹明B(RhB)等阳离子染料, 而对如甲基橙(MO)和荧光素钠(FS)等阴离子染料则难以吸附, 该COF可实现基于电荷模式的阴离子、 阳离子染料的分离. TFP-BDSA对阳离子染料的吸附动力学均遵循拟二级吸附动力学模型, 吸附过程符合Langmuir吸附模型, 其对MLB, CV和RhB的最大吸附容量分别高达1116, 1429和1638 mg/g. 与其它COFs材料相比, TFP-BDSA对CV和RhB的吸附容量最高. 该工作可为开发功能COFs材料实现对废水中有机污染物的快速吸附和有效去除提供参考.     

三维生物高分子/氧化石墨烯复合凝胶对阳离子染料吸附的研究

采用一种简便的方法制备了生物高分子调控的氧化石墨烯凝胶用于水污染处理.将生物高分子白蛋白(BSA)、壳聚糖(CS)、及脱氧核糖核酸(DNA)与氧化石墨烯(GO)共混,自组装形成水凝胶,最后冻干得到生物高分子/氧化石墨烯复合凝胶.通过扫描电镜、原子力显微镜、纳米粒度分析仪等分析复合凝胶的组装结构与表面电位.结果表明凝胶呈现内部联通的三维多孔结构,该结构有利于被吸附分子的快速内部扩散.红外光谱证明了生物高分子被成功负载到了凝胶网络中.然后将该复合凝胶用于阳离子染料的吸附,吸附实验表明这类生物高分子/氧化石墨烯复合凝胶对阳离子染料有很好的吸附效果,同时也对阴离子和非离子毒性分子有一定的吸附能力.研究了吸附时间,初始浓度,pH值等对凝胶吸附量的影响,并考察了凝胶的解吸附.最后详细探讨了GO-BSA、GO-CS和GO-DNA凝胶对亚甲基蓝(MB)吸附的动力学和吸附等温式.经吸附动力学拟合,生物高分子/氧化石墨烯复合凝胶吸附MB复合二级动力学模型和Langmuir等温吸附,对MB分子是单分子层吸附,吸附初期为大孔隙扩散,后期为粒子内扩散.     

改性SiO_2聚合物微球对阳离子染料的吸附行为

本文以3-氨丙基三乙氧基硅烷(KH-550)为改性剂,先在碱性条件下对SiO_2改性得到改性二氧化硅(Poly-SiO_2),再以丙烯酸、丙烯酰胺为单体,N,N′-亚甲基双丙烯酰胺(MBA)为交联剂,采用反相悬浮法对Poly-SiO_2进一步改性,制备了一种改性SiO_2聚合物微球(AA-Poly-SiO_2)。通过傅立叶变换红外光谱、热重分析、扫描电子显微镜、X射线粉末衍射分析其结构特性。考察了AA-Poly-SiO_2对含氮阳离子染料亚甲基蓝、碱性品红、甲基紫、乙基紫的吸附性能,研究了时间、pH、吸附剂用量、初始浓度对吸附染料的影响,以及吸附动力学和等温吸附过程。得到的AA-Poly-SiO_2的平均尺寸为8.20μm,比表面积为0.0725 m~2/g。其等温吸附符合Langmuir模型,吸附过程遵循Langmuir等温吸附和准二级动力学模型,为单层化学吸附。该AA-Poly-SiO_2对乙基紫的最大吸附容量可达1 000 mg/g。与常规聚丙烯酰胺微球相比,AA-Poly-SiO_2显示出更高的吸附容量,可以循环使用5次,吸附率仍在78%以上。     

具有染料选择吸附性的衍生于沸石咪唑酯骨架-67的NiCo-层状双氢氧化物设计与合成

以沸石咪唑类金属有机骨架(ZIF-67)为模板合成了一种新型的中空吸附剂NiCo-LDH@ZIF-67,该吸附剂对甲基橙具有良好的选择吸附性以及可循环性。 通过扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线粉末衍射仪(XRD)、红外光谱、电子能谱和氮气吸附-脱附等手段对样品进行了表征。 研究了溶液的pH值、甲基橙的初始浓度以及染料与吸附剂作用时间对NiCo-LDH@ZIF-67吸附性能的影响。 结果表明,该吸附剂对甲基橙的吸附动力学符合准二级动力学模型,且吸附等温线符合朗缪尔方程。 当pH值等于4, 吸附时间15 min,吸附剂用量为2400 mg/L时,该吸附剂对甲基橙的最大吸附量可达1766 mg/g,高于之前文献报道的类似吸附剂。 此外,NiCo-LDH@ZIF-67能从甲基橙和亚甲基蓝的混合溶液中选择性吸附甲基橙。     

具有染料选择吸附性的衍生于沸石咪唑酯骨架-67的NiCo-层状双氢氧化物设计与合成（英文）

以沸石咪唑类金属有机骨架(ZIF-67)为模板合成了一种新型的中空吸附剂NiCo-LDH@ZIF-67,该吸附剂对甲基橙具有良好的选择吸附性以及可循环性。通过扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线粉末衍射仪(XRD)、红外光谱、电子能谱和氮气吸附-脱附等手段对样品进行了表征。研究了溶液的pH值、甲基橙的初始浓度以及染料与吸附剂作用时间对NiCo-LDH@ZIF-67吸附性能的影响。结果表明,该吸附剂对甲基橙的吸附动力学符合准二级动力学模型,且吸附等温线符合朗缪尔方程。当pH值等于4,吸附时间15 min,吸附剂用量为2400 mg/L时,该吸附剂对甲基橙的最大吸附量可达1766 mg/g,高于之前文献报道的类似吸附剂。此外,NiCo-LDH@ZIF-67能从甲基橙和亚甲基蓝的混合溶液中选择性吸附甲基橙。     

磁性氧化石墨烯/聚苯胺纳米复合材料的制备 及再生循环吸附性研究

由氧化法和原位合成法成功制备了磁性氧化石墨烯/聚苯胺(Fe_3O_(4 )/GO/PANI,MPGO)纳米复合材料,使用X射线衍射、热重分析、红外光谱、VSM、BET等对所得材料进行了结构表征和性能测试,研究了复合材料对甲基橙染料的吸附性能。结果表明:pH为4时,MPGO吸附量最大,为198 mg·g~(-1);450 min达到吸附平衡,吸附量为211.08 mg·g~(-1)。MPGO对甲基橙的吸附行为符合Langmuir等温模型和准二级动力学模型;经过7次再生循环后,MPGO对甲基橙的吸附量保持为初始吸附量的72.2%,具有较好的重复利用性。     

磁性壳聚糖/Fe3O4/氧化石墨烯吸附剂的制备及其多染料吸附性能

为了提高壳聚糖的多染料吸附性能并使其便于固液分离,采用共沉淀法制备了壳聚糖、磁铁矿纳米颗粒、氧化石墨烯复合磁性吸附剂(CS/Fe₃O₄/GO)。系统的结构表征显示,CS包覆的Fe₃O₄磁性纳米颗粒均匀地分布在GO的表面。CS/Fe₃O₄/GO具有高达42.5 emu·g^-1的室温铁磁性,因此可在外加磁场中实现高效固液分离。研究表明,CS/Fe₃O₄/GO对亚甲基蓝(MB)、甲基橙(MO)和刚果红(CR)等多种染料具有良好的吸附性能,溶液的pH、初始浓度和吸附时间对其多染料吸附性能具有显著影响。在最佳条件下,CS/Fe₃O₄/GO对MB、MO和CR的吸附量分别达到210.6、258.6和308.9 mg·g^-1。CS/Fe₃O₄/GO具有优异的循环利用性能,经5次循环后仍能保留90%以上的原始吸附量。采用吸附等温线和吸附动力学对CS/Fe₃O₄/GO的多染料吸附性能进行了拟合分析,并详细讨论了其吸附机理。     

磁性壳聚糖/Fe3O4/氧化石墨烯吸附剂的制备及其多染料吸附性能

为了提高壳聚糖的多染料吸附性能并使其便于固液分离,采用共沉淀法制备了壳聚糖、磁铁矿纳米颗粒、氧化石墨烯复合磁性吸附剂(CS/Fe₃O₄/GO)。系统的结构表征显示,CS包覆的Fe₃O₄磁性纳米颗粒均匀地分布在GO的表面。CS/Fe₃O₄/GO具有高达42.5 emu·g-1的室温铁磁性,因此可在外加磁场中实现高效固液分离。研究表明,CS/Fe₃O₄/GO对亚甲基蓝(MB)、甲基橙(MO)和刚果红(CR)等多种染料具有良好的吸附性能,溶液的pH、初始浓度和吸附时间对其多染料吸附性能具有显著影响。在最佳条件下,CS/Fe₃O₄/GO对MB、MO和CR的吸附量分别达到210.6、258.6和308.9 mg·g-1。CS/Fe₃O₄/GO具有优异的循环利用性能,经5次循环后仍能保留90%以上的原始吸附量。采用吸附等温线和吸附动力学对...     

Facile synthesis of mesoporous magnesium oxide–graphene oxide composite for efficient and highly selective adsorption of hazardous anionic dyes

Mesoporous magnesium oxide–graphene oxide composite (MGC) has been synthesized using a facile post-immobilization method by mixing pre-synthesized magnesium oxide (MgO) with graphene oxide (GO). MgO used for fabrication of the composite has been synthesized using an environment-friendly method involving gelatin as a template. XRD, Raman and EDX analyses have confirmed the presence of MgO and GO in the composite. FTIR and SEM analyses of synthesized MGC have further elucidated the surface functionalities and morphology, respectively. Using N₂ adsorption–desorption isotherm, BET surface area of MGC has been calculated to be 55.9 m² g^?1 and BJH analysis confirmed the mesoporous nature of MGC. The application of synthesized MGC as a selective adsorbent for various toxic anionic dyes has been explored. Batch adsorption studies have been carried out to investigate the influence of different adsorption parameters on the adsorption of two anionic dyes: indigo carmine (IC) and orange G (OG). The maximum adsorption capacities exhibited by MGC for IC and OG are 252.4 and 24.5 mg g^?1, respectively. Plausible mechanism of dye adsorption has been explained in detail using FTIR analysis. In a mixture of cationic and anionic dyes, MGC selectively adsorbs anionic dyes with high separation factors, while in binary mixtures of anionic dyes, both dyes are adsorbed efficiently. Thus, MGC has been shown to be a potential adsorbent for the selective removal of anionic dyes from wastewater.

     

Fabrication of flexible graphene oxide paper-like adsorbent doped with magnetite nanoparticles for removal of dyes

Organic dyes are used in many industries, e.g., textile, cosmetics and food. Hence, contamination of organic dyes to water sources is a critical issue. To reduce water pollution by organic dyes, we propose a paper-like adsorbent with a practical and economical production procedure. Subsequently, a flexible adsorbent was produced using a one-step approach by vacuum filtration of graphene oxide (GO) and iron oxide nanoparticles (Fe₃O₄-NPs) containing dispersion through a membrane and quoted as GO/Fe₃O₄ paper. For comparison, GO paper was also prepared using the same procedure. Both papers were characterized using UV–VIS absorption spectroscopy, Fourier transform infrared spectroscopy, Raman spectroscopy, scanning electron microscopy, electron diffraction X-ray analysis, X-ray photoelectron spectroscopy, and powder X-ray diffraction techniques. At the steady-state conditions, GO/Fe₃O₄ and GO papers were performed as adsorbent for cationic dyes of methylene blue, neutral red, and anionic dyes of methyl orange and fluorescein. In general, the removal efficiency of GO/Fe₃O₄ paper was higher than that of GO paper for adsorption of all dyes and this adsorbent revealed satisfactory adsorption properties for cationic dyes when compared to anionic dyes.

     

Gold Nanoparticles Loaded on Activated Carbon as Novel Adsorbent for Kinetic and Isotherm Studies of Methyl Orange and Sunset Yellow Adsorption

In this research, a novel adsorbent gold nanoparticle loaded on activated carbon (Au-NP-AC) was synthesized by a low cost in a routine protocol. Subsequently, this novel material characterization and identification are followed by different techniques such as th eBruner–Emmet–Teller (BET) theory, scanning electron microcopy, and transmission electron microscopy analysis. Unique properties such as high BET surface area (>1229.55 m²/g) and low pore size (<22.46 Å) and average particle size lower than 48.798 Å in addition to high reactive atom and presence of various functional groups make it possible for efficient removal of sunset yellow (SY) and methyl orange (MO). Generally, the influence of variables including amount of adsorbent, initial dyes concentration, contact time, temperature on dyes removal percentage has great effect on removal percentage that their influence was optimized. The kinetic of proposed adsorption processes efficiently followed, pseudo-second-order and intra-particle diffusion approach. The equilibrium data of the removal strongly follow the Langmuir monolayer adsorption with high adsorption capacity in a short amount of time. This novel adsorbent by small amount (0.01 g) really is applicable for removal of high amount of both dyes (MO and SY) in short time (<18 minutes). Equilibrium data fitted well with the Langmuir model at all amount of adsorbent, while maximum adsorption capacity for MO 161.29 mg g^?1 and for SY 227.27 for 0.005 g of Au-NP-AC.     

The fabrication of a nanoscale polyoxometalate based magnetic adsorbent and its selective adsorption on cationic dyes

Amino group-functionalized Fe₃O₄ is loaded on a coordination complex-modified polyoxometalate nanoparticle. In this composite material, Fe₃O₄ and coordination complex-modified polyoxometalate are connected with intense hydrogen bonds as suggested by FTIR. This composite material exhibits excellent methylene blue (MB) adsorption, with adsorption capacity of 175.5 mg g^?1. It also possesses selective separation ability between cationic and anionic dye molecules. In binary solution of MB and methyl orange (MO), MB adsorption efficiency reaches 75%, but it exhibits almost no effect on the adsorption of methyl orange. The saturation magnetization value of this composite material is 18.89 emu g^?1, allowing magnetic separation, which facilitates the recycle and reuse of this composite adsorbent.     

Cetyltrimethylammonium bromide-coated magnetite nanoparticles as highly efficient adsorbent for rapid removal of reactive dyes from the textile companies’ wastewaters

The utilization of modified magnetite nanoparticles (Fe₃O₄ NPs) with a cationic surfactant (cetyltrimethylammonium bromide (CTAB)) as an efficient adsorbent was successfully carried out to remove reactive black 5 (RBBA), reactive red 198 (RRR) and reactive blue 21 (RTB) dyes from aqueous solutions. First, a reactor was designed to be simple, repeatable and efficient in its synthesis of Fe₃O₄ NPs via co-precipitation method. Then, an orthogonal array design (OAD), four factor-four level (4⁴) matrix was applied to assign affecting factors on removing of the dyes from aqueous solutions. The obtained results from ANOVA showed that the amount of CTAB and NaCl% significantly affect the adsorption of RBBA, RRR and RTB dyes. The sorption kinetics of the dyes were best described by a second-order kinetic model, suggesting chemisorptions mechanism. Also, dye adsorption equilibrium state data were fitted well to the Langmuir isotherm rather than Freundlich isotherm. Also, the maximum monolayer capacity, q_max, obtained from the Langmuir was 312.5, 163.9 and 556.2 mg g^-1 for RBBA, RRR and RTB, respectively. The obtained results in the present study indicated that the CTAB-coated Fe₃O₄ NPs can be an efficient adsorbent material for removal of reactive dyes form aqueous solutions.     

Novel graphene oxide/bentonite composite for uranium(VI) adsorption from aqueous solution

A novel graphene oxide/bentonite composite (GO/bentonite) was synthesized and then characterized through powder X-ray diffraction, fourier transform infrared spectroscopy, thermogravimetric analysis, scanning electron microscopy, and energy dispersive spectroscopy. Adsorption achieved equilibrium within 10 min. Moreover, U(VI) adsorption on GO/bentonite was highly dependent on solution pH and independent of ionic strength. These characteristics suggested that inner-sphere surface complexes of U(VI) formed on GO/bentonite. The adsorption of U(VI) from aqueous solution on GO/bentonite was fitted to the pseudo-second-order and Freundlich isotherm models. The maximum sorption capacity of GO/bentonite was 234.19 mg g^?1 under neutral pH at 303 K. GO/bentonite is a potentially powerful adsorbent for the efficient removal of U(VI) from aqueous solutions.     

Preparation and characterization of L-glutamic acid-functionalized graphene oxide for adsorption of Pb(II)

An efficient adsorbent (L-Glu/GO) was successfully synthesized by the reaction between L-glutamic acid (L-Glu) and graphene oxide (GO). The structure and morphology of this adsorbent were characterized by FTIR, SEM, XRD, and TGA. The SEM result indicated that the adsorbent was a nanomaterial with a size of about 50–400 nm. The adsorption experiments of various heavy ions on L-Glu/GO demonstrated that the adsorption performance of Pb(II) was better than others. Various variables affecting the adsorption of L-Glu/GO for Pb(II) were systematically explored. The experimental results indicated that the maximum adsorption capacity and equilibrium time of Pb(II) on L-Glu/GO were 513.4 mg g^?1 and 40 minute, respectively. The sorption kinetics and isotherm fitted well with the pseudo-second-order model and Langmuir model, respectively. The sorption mainly was a chemical process. Thermodynamic studies revealed that the adsorption was a spontaneous and exothermic process. The adsorbent could be regenerated with HCl solution. Hence, it was suggested that the L-Glu/GO could be applied in the removal of Pb(II) from wastewaters.     

GO/Fe3O4/有机胺复合材料的制备及对结晶紫染料的吸附性能

用改进的Hummers法制备了氧化石墨烯,用乙二胺、乙二胺与丁二胺/己二胺混溶来改性氧化石墨烯。用水热法制备了Fe3O4,并用物理混合法制备了GO/Fe3O4/有机胺的三元复合体系。用透射电镜、扫描电镜、红外光谱、热重分析、X射线衍射、VSM和XPS等对所制得的样品进行了结构表征和性能测试,研究了三元复合粒子对结晶紫染料的吸附性能及影响结晶紫染料吸附效果的因素。结果表明:所制备的Fe3O4的平均粒径约为200 nm,粒径分布均匀;复合物中GO为典型的片状结构,GO及有机胺的掺杂没有影响Fe3O4的尖晶石结构;复合物为超顺磁性,Ms为53.0 emu·g~(-1)。吸附结果表明:石墨烯/Fe3O4/有机胺的三元复合材料对结晶紫染料的最大吸附量随浓度增大而增大,而吸附结晶紫染料的移除率却随结晶紫染料浓度增大而减小,并趋向一定值;乙二胺和己二胺混溶比例为5∶1的GO/Fe3O4复合材料吸附性能最佳:结晶紫浓度为400 mg·L~(-1),最大吸附量为164.3 mg·L~(-1)。