Pore spanning lipid bilayers on mesoporous silica having varying pore size

Synthetic lipid bilayers have similar properties as cell membranes and have been shown to be of great use in the development of novel biomimicry devices. In this study, lipid bilayer formation on mesoporous silica of varying pore size, 2, 4, and 6 nm, has been investigated using quartz crystal microbalance with dissipation monitoring (QCM-D), fluorescent recovery after photo bleaching (FRAP), and atomic force microscopy (AFM). The results show that pore-spanning lipid bilayers were successfully formed regardless of pore size. However, the mechanism of the bilayer formation was dependent on the pore size, and lower surface coverages of adsorbed lipid vesicles were required on the surface having the smallest pores. A similar trend was observed for the lateral diffusion coefficient (D) of fluorescently labeled lipid molecules in the membrane, which was lowest on the surface having the smallest pores and increased with the pore size. All of the pore size dependent observations are suggested to be due to the hydrophilicity of the surface, which decreases with increased pore size.     

Lipid bilayer deposition and patterning via air bubble collapse

We report a new method for forming patterned lipid bilayers on solid substrates. In bubble collapse deposition (BCD), an air bubble is first "inked" with a monolayer of phospholipid molecules and then touched to the surface of a thermally oxidized silicon wafer and the air is slowly withdrawn. As the bubble shrinks, the lipid monolayer pressure increases. Once the monolayer exceeds the collapse pressure, it folds back on itself, depositing a stable lipid bilayer on the surface. These bilayer disks have lateral diffusion coefficients consistent with high quality supported bilayers. By sequentially depositing bilayers in overlapping areas, fluid connections between bilayers of different compositions are formed. Performing vesicle rupture on the open substrate surrounding this bilayer patch results in a fluid but spatially isolated bilayer. Very little intermixing was observed between the vesicle rupture and bubble-deposited bilayers.     

Supported lipid bilayers lifted from the substrate by layer-by-layer polyion cushions on self-assembled monolayers

The formation of lipid bilayers, lifted from the solid substrate by layer-by-layer polyion cushions, on self-assembled monolayers (SAMs) on gold was investigated by surface plasmon resonance (SPR) and fluorescence recovery after photobleaching (FRAP). The polyions poly(diallyldimethylammonium chloride) (PDDA) and polystyrene sulfonate (PSS) sodium salt were used for the layer-by-layer polyion macromolecular assembly. The cushion was formed by electrostatic interaction of PDDA/PSS/PDDA layers with a negatively charged surface of an SAM of 11-mercaptoundecanoic acid (MUA) on gold. The lipid bilayer membranes were deposited by vesicle fusion with different compositions of SOPS (an anionic lipid, 1-stearoyl-2-oleoyl-phosphatidylserine) and POPC (a zwitterionic lipid, 1-palmitoyl-2-oleoylphosphatidylcholine). In the case of pure SOPS and for lipid mixtures with a POPC composition up to 25%, single bilayers were deposited. FRAP experiments showed that single bilayers supported on PDDA/PSS/PDDA/MUA were mobile at room temperature, with lateral coefficients of approximately (1.2–2.1)×10⁻⁹ cm²/s. The kinetics of the addition of the ion-channel-forming peptide protegrin-1 to the supported bilayers was detected by SPR. A two-step interaction was observed, similar to the association behavior of protegrin-1 with bilayers supported on PDDA/MUA. The results are similar to that of supported lipid bilayers without a layer-by-layer cushion. The model membrane system in this work is a potential biosensor for mimicking the natural activities of biomolecules and is a possible tool to investigate the fundamental properties of biomembranes.     

Directed assembly of surface-supported bilayers with transmembrane helices

The lateral assembly of transmembrane (TM) helices gives rise to membrane proteins with complex folds, which play important roles in biochemical processes. Therefore, the assembly of surface-supported bilayers containing TM helices is the first step toward the development of functional biomembrane mimetics. Here we report novel directed assembly of surface-supported lipid bilayers with laterally mobile TM helices. The TM helices were incorporated into lipid monolayers at the air/water interface, and the monolayers were then transferred onto glass substrates using Langmuir-Blodgett (LB) deposition. Finally, bilayers were assembled using lipid vesicle fusion on top of the LB monolayers. The novelty is the incorporation of the peptides into the monolayer at the first step of bilayer assembly, which allows control over the peptide concentration and orientation. The transmembrane orientation of the peptides was confirmed using oriented circular dichroism (OCD), lateral mobility was assessed using fluorescence recovery after photobleaching (FRAP), and diffusion coefficients were determined using a novel boundary profile evolution (BPE) method. The described directed-assembly approach can be used to develop versatile bilayer platforms for studying membrane proteins interactions in native bilayer environments.     

Composition and asymmetry in supported membranes formed by vesicle fusion

The structure and formation of supported membranes at silica surfaces by vesicle fusion was investigated by neutron reflectivity and quartz crystal microbalance (QCM-D) measurements. The structure of equimolar phospholipid mixtures of DLPC-DPPC, DMPC-DPPC, and DOPC-DPPC depends intricately on the vesicle deposition conditions. The supported bilayer membranes exhibit varying degrees of compositional asymmetry between the monolayer leaflets, which can be modified by the deposition temperature as well as the salt concentration of the vesicle solution. The total lipid composition of the supported bilayers differs from the composition of the vesicles in solution, and the monolayer proximal to the silica surface is always enriched in DPPC compared to the distal monolayer. The results, which show unambiguougsly that some exchange and rearrangement of lipids occur during vesicle deposition, can be rationalized by considering the effects of salt screening and temperature on the rates of lipid exchange, rearrangement, and vesicle adsorption, but there is also an intricate dependence on the lipid-lipid interactions. Thus, although both symmetric and asymmetric supported bilayers can be prepared from vesicles, the optimal conditions are sensitive to the lipid composition of the system.     

Lateral mobility of tethered vesicle-DNA assemblies

Supported lipid membranes are particularly attractive for use in biochemical assays because of their resistance to nonspecific adsorption and their unique ability to host transmembrane proteins. Although ideal for use in many surface-based detection techniques, supported bilayers can make the incorporation of proteins problematic due to the steric constraints of the underlying substrate. A recently developed strategy overcomes this obstacle by tethering liposomes to supported lipid bilayers via cholesterol-tagged DNA. Due to the fluidity of the bilayer, the vesicle assemblies exhibited significant lateral mobility. The corresponding diffusion coefficients were then investigated using fluorescence recovery after photobleaching (FRAP). The diffusivity was neither sensitive to the size of the vesicles nor to the length of the DNA tether. However, changing from single cholesterol tethers to double cholesterol tethers caused a decrease in the diffusivity of the assemblies by a factor of 3. Perhaps even more notable was the fact that single cholesterol-DNA without vesicles diffused 6 times faster than the corresponding assemblies. Double cholesterol-DNA diffused 11 times faster. This discrepancy is believed to arise from the fact that each vesicle is tethered to the bilayer by multiple DNA pairs.     

Vesicle and bilayer formation of diphytanoylphosphatidylcholine (DPhPC) and diphytanoylphosphatidylethanolamine (DPhPE) mixtures and their bilayers' electrical stability

Lipid bilayers are of interest in applications where a cell membrane mimicking environment is desired. The performance of the lipid bilayer is largely dependent on the physical and chemical properties of the component lipids. Lipid bilayers consisting of phytanoyl lipids have proven to be appropriate choices since they exhibit high mechanical and chemical stability. In addition, such bilayers have high electrical resistances. Two different phytanoyl lipids, 1,2-diphytanoyl-sn-glycero-3-phosphocholine (DPhPC) and 1,2-diphytanoyl-sn-glycero-3-phosphoethanolamine (DPhPE), and various combinations of the two have been investigated with respect to their behavior in aqueous solutions, their interactions with solid surfaces, and their electrical stability. Dynamic light scattering, nuclear magnetic resonance diffusion, and cryogenic transmission electron microscopy measurements showed that pure DPhPC as well as mixtures of DPhPC and DPhPE consisting of greater than 50% (mol%) DPhPC formed unilamellar vesicles. If the total lipid concentration was greater than 0.15g/l, then the vesicles formed solid-supported bilayers on plasma-treated gold and silica surfaces by the process of spontaneous vesicle adsorption and rupture, as determined by quartz crystal microbalance with dissipation monitoring and atomic force microscopy. The solid-supported bilayers exhibited a high degree of viscoelasticity, probably an effect of relatively high amounts of imbibed water or incomplete vesicle fusion. Lipid compositions consisting of greater than 50% DPhPE formed small flower-like vesicular structures along with discrete liquid crystalline structures, as evidenced by cryogenic transmission electron microscopy. Furthermore, electrophysiology measurements were performed on bilayers using the tip-dip methodology and the bilayers' capacity to retain its electrical resistance towards an applied potential across the bilayer was evaluated as a function of lipid composition. It was shown that the lipid ratio significantly affected the bilayer's electrical stability, with pure DPhPE having the highest stability followed by 3DPhPC:7DPhPE and 7DPhPC:3DPhPE in decreasing order. The bilayer consisting of 5DPhPC:5DPhPE had the lowest stability towards the applied electrical potential.     

Characterization of phospholipid bilayer formation on a thin film of porous SiO2 by reflective interferometric Fourier transform spectroscopy (RIFTS)

Classical methods for characterizing supported artificial phospholipid bilayers include imaging techniques such as atomic force microscopy and fluorescence microscopy. The use in the past decade of surface-sensitive methods such as surface plasmon resonance and ellipsometry, and acoustic sensors such as the quartz crystal microbalance, coupled to the imaging methods, have expanded our understanding of the formation mechanisms of phospholipid bilayers. In the present work, reflective interferometric Fourier transform spectrocopy (RIFTS) is employed to monitor the formation of a planar phospholipid bilayer on an oxidized mesoporous Si (pSiO(2)) thin film. The pSiO(2) substrates are prepared as thin films (3 μm thick) with pore dimensions of a few nanometers in diameter by the electrochemical etching of crystalline silicon, and they are passivated with a thin thermal oxide layer. A thin film of mica is used as a control. Interferometric optical measurements are used to quantify the behavior of the phospholipids at the internal (pores) and external surfaces of the substrates. The optical measurements indicate that vesicles initially adsorb to the pSiO(2) surface as a monolayer, followed by vesicle fusion and conversion to a surface-adsorbed lipid bilayer. The timescale of the process is consistent with prior measurements of vesicle fusion onto mica surfaces. Reflectance spectra calculated using a simple double-layer Fabry-Perot interference model verify the experimental results. The method provides a simple, real-time, nondestructive approach to characterizing the growth and evolution of lipid vesicle layers on the surface of an optical thin film.     

Supported lipid bilayers at skeletonized surfaces for the study of transmembrane proteins

Skeletonized zirconium phosphonate surfaces are used to support planar lipid bilayers and are shown to be viable substrates for studying transmembrane proteins. The skeletonized surfaces provide space between the bilayer and the solid support to enable protein insertion and avoid denaturation. The skeletonized zirconium octadecylphosphonate surfaces were prepared using Langmuir-Blodgett techniques by mixing octadecanol with octadecylphosphonic acid. After zirconation of the transferred monolayer, rinsing the coating with organic solvent removes the octadecanol, leaving holes in the film ranging from ～50 to ～500 nm in diameter, depending on the octadecanol content. Upon subsequent deposition of a lipid bilayer, either by vesicle fusion or by Langmuir-Blodgett/Langmuir-Schaefer techniques, the lipid assemblies span the holes providing reservoirs beneath the bilayer. The viability of the supported bilayers as model membranes for transmembrane proteins was demonstrated by examining two approaches for incorporating the proteins. The BK channel protein inserts directly into a preformed bilayer on the skeletonized surface, in contrast to a bilayer on a nonskeletonized film, for which the protein associates only weakly. As a second approach, the integrin α(5)β(1) was reconstituted in lipid vesicles, and its inclusion in supported bilayers on the skeletonized surface was achieved by vesicle fusion. The integrin retains its ability to recognize the extracellular matrix protein fibronectin when supported on the skeletonized film, again in contrast to the response if the bilayer is supported on a nonskeletonized film.     

Lipid mobility controls the diffusion of small biopolymer adsorbates

Recent studies on the diffusion of adsorbed polymers such as DNA on supported lipid bilayers have suggested that such strongly adsorbed polymers can be treated similarly to a polymer "in" a 2D fluid, but this conjecture has not been experimentally verified. To test this hypothesis and also to gain a better understanding of polymer dynamics in two dimensions, we designed an experimental protocol-the lateral transport of a short, single-stranded DNA oligonucleotide adsorbed on a supported cationic lipid bilayer. Fluorescence recovery after photobleaching (FRAP) analysis reveals that the diffusivity of the adsorbed DNA quantitatively tracks that of the underlying lipid, even though the bilayer mobility changes by 2 orders of magnitude with changes in temperature. Interestingly, our results for short, extended, adsorbed biopolymers quantitatively track those for globular proteins in lipid bilayers. We thus conclude that short macromolecules that are strongly adsorbed on lipid bilayers can be treated similarly to macromolecules in the bilayer.     

Formation and characterization of fluid lipid bilayers on alumina

Fluid lipid bilayers were deposited on alumina substrates with the use of bubble collapse deposition (BCD). Previous studies using vesicle rupture have required the use of charged lipids or surface functionalization to induce bilayer formation on alumina, but these modifications are not necessary with BCD. Photobleaching experiments reveal that the diffusion coefficient of POPC on alumina is 0.6 microm (2)/s, which is much lower than the 1.4-2.0 microm (2)/s reported on silica. Systematically accounting for roughness, immobile regions and membrane viscosity shows that pinning sites account for about half of this drop in diffusivity. The remainder of the difference is attributed to a more tightly bound water state on the alumina surface, which induces a larger drag on the bilayer.     

Fusion of small unilamellar vesicles onto laterally mixed self-assembled monolayers of thiolipopeptides

Monolayers of the thiolipopeptide NH(2)-Cys-Ala-Ser-Ala-Ala-Ser-Ser-Ala-Pro-Ser-Ser-(Myr)Lys(Myr)-OH (III) were formed on gold surfaces by self-assembly, mixed with a lateral spacer of the same peptide composition, NH(2)-Cys-Ala-Ser-Ala-Ala-Ser-Ser-Ala-Pro-Ser-Ser-Lys-OH (I). Different mixing ratios were employed ranging from 0.1 to 1, corresponding to 10-100% thiolipopeptide. These self-assembled monolayers (SAMs) were then exposed to a suspension of liposomes with the aim of forming lipid bilayers as a function of the mixing ratio. A clear optimum with respect to homogeneity and electrical properties of the membranes was obtained in the middle region (0.5) of mixing ratio, as revealed by surface plasmon resonance spectroscopy, impedance spectroscopy, and fluorescence microscopy. The combination of these methods was shown to be a powerful tool, although a true lipid bilayer was not obtained. Instead, vesicle adsorption was shown to be the predominant process, and FRAP (fluorescence recovery after photobleaching) measurements showed that the films were not fluid on the micrometer length scale.     

Silica colloidal crystals as three-dimensional scaffolds for supported lipid films

This report describes the assembly of laterally diffusive lipid layers within the pores of colloidal crystals for potential application in membrane-based sensing. The amount of lipid encapsulated within colloidal crystals depends upon the method used to introduce the lipid to the crystalline substrate. Relative to a planar supported lipid bilayer, lipid loading in a 6.6 microm thick crystal was 15-73 times greater, as observed by fluorescence microscopy. Protein adsorption studies indicate that the crystal pores are open and that the silica surface of the crystal is passivated with respect to adsorption of a model protein when coated with POPC. Furthermore, the mesoporous environment of the colloidal crystal is found to protect lipid films from drying and rehydration processes that destroy planar supported lipid bilayers. The potential of colloidal crystal encapsulated lipid films for chemical sensing is demonstrated by a model protein binding assay.     

Measuring lipid asymmetry in planar supported bilayers by fluorescence interference contrast microscopy

There is substantial scientific and practical interest in engineering supported lipid bilayers with asymmetric lipid distributions as models for biological cell membranes. In principle, it should be possible to make asymmetric supported lipid bilayers by either the Langmuir-Blodgett/Schafer (LB/LS) or Langmuir-Blodgett/vesicle fusion (LB/VF) techniques (Kalb et al. Biochim. Biophys. Acta 1992, 1103, 307-316). However, the retention of asymmetry in biologically relevant lipid bilayers has never been experimentally examined in any of these systems. In the present work, we developed a technique that is based on fluorescence interference contrast (FLIC) microscopy to measure lipid asymmetry in supported bilayers. We compared the final degree of lipid asymmetry in LB/LS and LB/VF bilayers with and without cholesterol in liquid-ordered (l(o)) and liquid-disordered (l(d)) phases. Of five different fluorescent lipid probes that were examined, 1,2-dipalmitoyl-phosphatidylethanolamine-N-[lissamine rhodamine B] was the best for studying supported bilayers of complex composition and phase by FLIC microscopy. An asymmetrically labeled bilayer made by the LB/LS method was found to be at best 70-80% asymmetric once completed. In LB/LS bilayers of either l(o) or l(d) phase, cholesterol increased the degree of lipid mixing between the opposing monolayers. The use of a tethered polymer support for the initial monolayer did not improve lipid asymmetry in the resulting bilayer. However, asymmetric LB/VF bilayers retained nearly 100% asymmetric label, with or without the use of a tethered polymer support. Finally, lipid mixing across the center of LB/LS bilayers was found to have drastic effects on the appearance of l(d)-l(o) phase coexistence as shown by epifluorescence microscopy.     

Weakly coupled lipid bilayer membranes on multistimuli-responsive poly(N-isopropylacrylamide) copolymer cushions

Polymer-cushioned lipid bilayers are frequently used to mimic the native environment of cellular membranes in respect to the extracellular matrix and intracellular structures. With the aim to actively tune lipid membrane characteristics, we pursue the approach to use temperature and pH responsive polymer thin films of poly(N-isopropylacrylamide-co-carboxyacrylamide) (PNIPAAm-co-carboxyAAM) as cushions for supported lipid bilayers. A cationic lipid bilayer composed of dioleoylphosphatidylcholine (DOPC) and dioleoyltrimethylammoniumpropane (DOTAP) (9:1) was formed on top of the polymer thin film in a drying/rehydration process. Fluorescence recovery after photobleaching (FRAP) yielded higher lipid diffusion coefficients (6.3-9.6 μm(2) s(-1)) on polymer cushions in comparison to solid glass supports (3.0-5.9 μm(2) s(-1)). No correlation of the lipid mobility was found with the swelling state of (PNIPAAm-co-carboxyAAM), which is ascribed to restrained interfacial electrostatic interactions and dispersion forces. The results revealed a minimal coupling of the lipid bilayer with the polymer cushions, and thus, bilayers supported by (PNIPAAm-co-carboxyAAM) provide interesting opportunities for unperturbed lipid diffusion combined with control of transmembrane protein mobility due to the impact of a tunable frictional drag.     

Role of nanomechanical properties in the tribological performance of phospholipid biomimetic surfaces

The role of phospholipid bilayers in controlling and reducing frictional forces between biological surfaces is investigated by three complementary experiments: friction forces are measured using a homemade tribometer, mechanical resistance to indentation is measured by AFM, and lipid bilayer degradation is controlled in situ during friction testing using fluorescence microscopy. DPPC lipid bilayers in the solid phase generate friction coefficients as low as 0.002 (comparable to that found for cartilage) that are stable through time. DOPC bilayers formed by the vesicle fusion method or the adsorption of mixed micelles generate higher friction coefficients. These coefficients increased through time, during which the bilayers degraded. The friction coefficient is correlated with the force needed to penetrate the bilayer with the AFM tip. With only one bilayer in the contact region, the friction increased to a similar value of about 0.08 for the DPPC and DOPC. Our study therefore shows that good mechanical stability of the bilayers is essential and suggests that the low friction coefficient is ensured by the hydration layers between adjacent lipid bilayers.     

Assembly of lipid bilayers on silica and modified silica colloids by reconstitution of dried lipid films

A method is presented for the assembly of lipid bilayers on silica colloids via reconstitution of dried lipid films solvent-cast from chloroform within packed beds of colloids ranging from 100 nm to 10 μm in diameter. Rapid solvent evaporation from the packed bed void volume results in uniform distribution of dried lipid throughout the colloidal bed. Fluorescence measurements indicate that significant, if not quantitative, retention of DOPC or DPPC films cast between sub-bilayer and multilayer quantities occurs when the colloids are redispersed in aqueous solution. Phospholipid bilayers assembled in this manner are shown to effectively passivate the surface of 250 nm colloids to nonspecific adsorption of bovine serum albumin. The method is shown to be capable of preparing supported bilayers on colloid surfaces that do not generally support vesicle fusion such as poly(ethylene glycol) (PEG) modified silica colloids. Bilayers of lipids that have not been reported to self-assemble by vesicle fusion, including gel-phase lipids and single-chain diacetylene amphiphiles, can also be formed by this method. The utility of the solid-core support is demonstrated by the facile assembly of supported lipid bilayers within fused silica capillaries to generate materials that are potentially suitable for the analysis of membrane interactions in a microchannel format.     

Lipid bilayers on polyacrylamide brushes for inclusion of membrane proteins

The ability of neutral polymer cushions to support neutral lipid bilayers for the incorporation of mobile transmembrane proteins was investigated. Polyacrylamide brush layers were grown on fused silica using atom-transfer radical polymerization to provide polymer layers of 2.5-, 5- and 10-nm thickness. Lipid bilayers composed of POPC (1-palmitoyl-2-oleoyl-sn-glycero-3-phosphocholine) were formed by vesicle fusion onto bare fused silica and onto each of the polyacrylamide layers. Bilayer fluidity was assessed by the diffusion of a probe, NBD-labeled phosphatidylcholine, using fluorescence recovery after photobleaching. A transmembrane protein, the human delta-opioid receptor, was inserted into each lipid bilayer, and its ability to bind a synthetic ligand, DPDPE, cyclic[2-d-penicillamine, 5-d-penicillamine]enkephalin, was detected using single-molecule fluorescence spectroscopy by labeling this ligand with a rhodamine dye. The transmembrane protein was observed to bind the ligand for all bilayers tested. The protein's electrophoretic mobility was probed by monitoring the fluorescence from the bound ligand. The 5-nm polyacrylamide thickness gave the fastest diffusion for the fluorescent lipid probe (D(1) = 2.0(+/-1.2) x 10(-7) and D(2) = 1.2(+/-0.5) x 10(-6) cm(2)/s) and also the largest electrophoretic mobility for the transmembrane protein (3 x 10(-8) cm(2)/V.s). The optimum in polymer thickness is suggested to be a tradeoff between decoupling from the substrate and increasing roughness of the polymer surface.     

Prodan fluorescence detects the bilayer packing of asymmetric phospholipids

The bilayer phase behavior of asymmetric phospholipids, palmitoylstearoylphosphatidylcholine (PSPC) and stearoylpalmitoylphosphatidylcholine (SPPC), with different vesicle sizes (large multilamellar vesicle (LMV) and giant multilamellar vesicle (GMV)) was investigated by fluorescence spectroscopy using a polarity-sensitive fluorescent probe Prodan under high pressure. The results were compared with those of a symmetric phospholipid, diheptadecanoyl PC (C17PC). The difference in phase transitions of the PSPC and SPPC bilayers and in thermodynamic quantities of the transitions was hardly observed between LMV and GMV as the case of the C17PC bilayer. On the other hand, the Prodan fluorescence showed clear differences between LMV and GMV of the asymmetric PC bilayers. From the second derivative of Prodan fluorescence spectra, the three dimensional image plots in which we can clearly see the location of Prodan in the bilayer membrane as blue valleys were constructed for LMV and GMV under high pressure. We revealed from the plots that the bilayer packing is significantly dependent on not only the vesicle size but also the acyl-chain asymmetry of PC molecule in addition to the phase states. It was found that the packing of the gel phases of the asymmetric PC bilayers is weaker than that of the symmetric PC bilayer, and the size of vesicle affects the packing of the interdigitated gel phase the most markedly among three gel phases. This study suggests that the Prodan molecules can detect the effect of vesicle size on the phase states for the asymmetric PC bilayers, and they become a useful indicator for various membrane properties, especially bilayer interdigitation.     

Creation of lipid partitions by deposition of amphipathic viral peptides

Phospholipid vesicles exhibit a natural characteristic to fuse and reform into a continuous single bilayer membrane on hydrophilic solid substrates such as glass, mica, and silica. The resulting solid-supported bilayer mimics physiological tendencies such as lipid flip-flop and lateral mobility. The lateral mobility of fluorescently labeled lipids fused into solid-supported bilayers is found to change upon deposition on the membrane surface of an amphipathic alpha-helical peptide (AH) derived from the hepatitis C virus (HCV) NS5A protein. The binding of the AH peptide to a phospholipid bilayer, with the helical axis parallel to the bilayer, leads to immobilization of the bilayer. We used AFM to better understand the mechanistic details of this specific interaction, and determined that the diminished fluidity of the bilayer is due to membrane thinning. Utilizing this specific interaction between AH peptides and lipid molecules, we demonstrate a novel process for the creation of lipid partition by employing AH peptides as agents to immobilize lipid molecules, thus creating a patterned solid support with partition-defined areas of freely mobile lipid bilayers. This architecture could have a wide range of applications in novel sensing, biotechnology, high-throughput screening, and biomimetic strategies.