Influence of composition on corroding process of Na<Subscript>2</Subscript>O-K<Subscript>2</Subscript>O-CaO-ZrO<Subscript>2</Subscript>-SiO<Subscript>2</Subscript> glasses

The corroding process of six glasses of the Na₂O-K₂O-CaO-ZrO₂-SiO₂ system with ZrO₂content 0–2.13 mass % by water was observed during static tests at 121°C and pressure of 0.25 MPa in steam sterilizer. Significant increase of Na⁺ and K⁺ content in leachates was observed after the addition of ZrO₂ into glass. Further increase of the content of ZrO₂ in glasses slowed down the rate of Na⁺ and K⁺ leaching. The leaching process of SiO₂ as well as Na⁺, K⁺, and Ca²⁺ ions was evaluated on the basis of comparison with model leaching processes. Variation of the concentrations of Na⁺, K⁺, Ca²⁺, and SiO₂ in leachates with time was described by empirical equation. Observed changes in the initial leaching rates of Na⁺, K⁺, Ca²⁺, and SiO₂ can be ascribed to the content of ZrO₂ in glasses. The presence of ZrO₂ in glasses reduced the overall rate of glass dissolution.     

Thermal behaviour and properties of Na<Subscript>2</Subscript>O-TiO<Subscript>2</Subscript>-P<Subscript>2</Subscript>O<Subscript>5</Subscript> glasses

Differential scanning calorimetry (DSC) and thermomechanical analysis (TMA) were used to study the thermal behaviour of (50-x)Na₂O-xTiO₂-50P₂O₅ and 45Na₂O-yTiO₂-(55-y)P₂O₅ glasses. The addition of TiO₂ to the starting glasses (x=0 and y=5 mol% TiO₂) resulted in a nonlinear increase of glass transition temperature and dilatation softening temperature, whereas the thermal expansion coefficient decreased. All prepared glasses crystallize under heating within the temperature range of 300–610°C. The contribution of the surface crystallization mechanism over the internal one increases with increasing TiO₂ content. With increasing TiO₂ content the temperature of maximum nucleation rate is also gradually shifted from a value close to the glass transition temperature towards the crystallization temperature. X-ray diffraction measurements showed that the major compounds formed by glass crystallization were NaPO₃, TiP₂O₇ and NaTi₂(PO₄)₃. The chemical durability of the glasses without titanium oxide is very poor, but with the replacement of Na₂O or P₂O₅ by TiO₂, it increases sharply.     

Influence of ZrO<Subscript>2</Subscript> on the physicochemical properties of the ZrO<Subscript>2</Subscript>-TiO<Subscript>2</Subscript> binary system

A series of ZrO₂-TiO₂ mixed oxides with different weight ratios (5, 20, and 30% ZrO₂) were prepared by wet impregnation of TiO₂-P25 Degussa with certain amounts of ZrO(NO₃)₂·6H₂O (Fluka) dissolved in deionised water. The samples were characterized by the XRD, , , , and BET methods. An increase in ZrO₂ content shifted the phase transition temperature (anatase into rutile) toward higher temperatures. X-ray diffraction using an Anton Paar XRK900 reactor chamber indicated that, in the case of samples containing ZrO₂, an additional diffraction peak appeared after cooling down to 25°C. This peak could be attributed to a polymorph of TiO₂ such as in the single crystal of anatase or hexagonal form of TiO₂ which appears in the presence of ZrO₂. Generally, the preparation of dioxide systems can modify the properties of pure compounds or generate new catalytic sites as a result of strong interaction between ZrO₂ and TiO₂ oxides. The binary systems exhibit advantages like strong acidity, extended specific surface area, and high thermal stability in comparison with TiO₂. The article is published in the original.     

Some studies on the phase formation and kinetics in TiO<Subscript>2</Subscript> containing lithium aluminum silicate glasses nucleated by P<Subscript>2</Subscript>O<Subscript>5</Subscript>

Lithium aluminum silicate (LAS) glasses of compositions (wt%) 10.6Li₂O–71.7SiO₂–7.1Al₂O₃–4.9K₂O–3.2B₂O₃–1.25P₂O₅–1.25TiO₂ were prepared by the melt quench technique. Crystallization kinetics was investigated by the method of Kissinger and Augis–Bennett using differential thermal analysis (DTA). Based on the DTA data, glass ceramics were prepared by single-, two-, and three-step heat treatment schedules. The interdependence of different phases formed, microstructure, thermal expansion coefficient (TEC) and microhardness (MH) was investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM), thermo-mechanical analysis (TMA), and microhardness (MH) measurements. Crystallization kinetics revealed that Li₂SiO₃ is the kinetically favored phase with activation energy of 91.10 kJ/mol. An Avrami exponent of n = 3.33 indicated the dominance of bulk crystallization. Based upon the formation of phases, it was observed that the two-stage heat treatment results in highest TEC glass ceramics. The single-step heat treatment yielded glass ceramics with the highest MH.     

The effect of PO<Subscript>2,5</Subscript> and AlO<Subscript>1,5</Subscript> additions on structural changes and crystallization behavior of SiO<Subscript>2</Subscript>-TiO<Subscript>2</Subscript> sol-gel derived glasses and thin films

SiO₂-TiO₂-PO_2,5 (STP) and SiO₂-TiO₂-AlO_1,5 (STA) glasses were prepared by sol-gel processing. Their infrared absorption spectra (IR), differential thermal analysis curves (DTA) and X-ray diffraction patterns (XRD) have been recorded. In the SiO₂-TiO₂ system, the chemical homogeneity of the sol-gel glass could be evaluated by the relative concentration of Si-O-Ti heterocondensation comparing to Si-O-Si homocondensation. For the STA system, a gradual decrease of the Si-O-Ti/Si-O-Si band ratio (based on IR spectra) with the addition of Al₂O₃ is observed, with the simultaneous formation of Si-O-Al and Ti-O-Al bounds, i.e Al₃ ⁺ ions are dissolved in the SiO₂-TiO₂ glass matrix and do not promote glass-in-glass phase-separation in the composition range of 0–15 mol% AlO_1.5. In the STP system, on the other hand, P=O bond IR stretch in the ternary glasses indicates that P=O free PO₂O_2/2 ⁻ tetrahedra are formed, rather than the double bonded POO_3/2 tetrahedra that usually occur in binary SiO₂-P₂O₅ glasses. It can be concluded that SiO₂-TiO₂-P₂O₅ glass separates into a SiO₂-rich phase and a TiO₂(P₂O₅)-rich phase. During heat-treatment in STA system only anatase precipitates, even at T ~ 1,000 °C, while in for STP, anatase (TiO₂) or (TiO)₂P₂O₇ (TOP) crystals precipitate at ~600 °C, depending on the P₂O₅ concentration. The major crystal phase, cristobalite, precipitated at ~1,000 °C and at ~1,200 °C, the P-containing phase melts.     

Chemical durability of MoO<Subscript>3</Subscript>-P<Subscript>2</Subscript>O<Subscript>5</Subscript> and K<Subscript>2</Subscript>O-MoO<Subscript>3</Subscript>-P<Subscript>2</Subscript>O<Subscript>5</Subscript> glasses

Thermal and chemical durability studies of the phosphate glasses belonging to the binary MoO₃-P₂O₅ and the ternary K₂O-MoO₃-P₂O₅ systems are reported. The chemical resistant attack tests carried out on the free alkaline MoO₃-P₂O₅ glasses show that the glass associated with the P/Mo ratio 2 has the high chemical durability. It shows also a high glass transition temperature value. The above findings are interpreted in terms of the cross-link density of the glasses and the strength of the M-O bonds (M=P, Mo). The influence of K₂O addition on the properties (density, T _g, durability) of this binary high water resistant glass is studied. It is found that the chemical durability along with the other physical properties are reduced by the incroporation of K₂O in the glass matrix. The results were explained by assuming the formation of non-bridging oxygens and weak bonds. The mechanism of the dissolution of these glasses is proposed.     

Thermal properties of oxide glasses

Glasses with the composition Li₂O·2SiO₂·nTiO₂ and Li₂O·2SiO₂·nZrO₂, where n=0, 0.03, 0.062, 0.1, were prepared and the onset and peak temperatures have been determined by DTA. From these characteristic temperatures, the kinetic parameters describing the nucleation and crystal growth have been obtained by isoconversional methods. The kinetic parameters have been used for the calculation of nucleation and crystal growth times for individual glasses so determining the order of glass stability at reheating. The stability of glasses increases with the content of TiO₂ or ZrO₂ where the increase is higher for ZrO₂. Within the concentration range under study, the increase of both times with the metal oxide concentration is quadratic. It has been discussed that the crystallization kinetics does not obey the Arrhenius law and, therefore, when using the evaluation methods based on this law, the results should not be extrapolated outside the temperature range of the measurements.     

Glasses in the CuNbOF<Subscript>5</Subscript>-BaF<Subscript>2</Subscript> and CuNbOF<Subscript>5</Subscript>-PbF<Subscript>2</Subscript> systems

Nonhygroscopic, colored glasses have been synthesized in the CuNbOF₅-BaF₂ and CuNbOF₅-PbF₂ systems proceeding from crystals of the complex compound CuNbOF₅ · 4H₂O. The glasses have been studied structurally and thermally. The crystallization resistance of the glasses has been studied as a function of glass composition. Lead difluoride glasses are more stable than barium difluoride glasses of the same composition. These glasses have lower glass-transition temperatures than the binary glasses formed in the NbO₂F-BaF₂ system. The glass structure is built of Nb(O,F)₆ polyhedra, which are linked in glass networks through oxygen bridges. Modifier cations influence both the structure of glass networks and the linkage of polyhedra.     

Thermal analysis study of Bi<Subscript>2</Subscript>Sr<Subscript>2</Subscript>Ca<Subscript>2</Subscript>Cu<Subscript>3-x</Subscript>Er<Subscript>x</Subscript>O<Subscript>10+δ</Subscript> glass-ceramic system

Summary We have fabricated glasses in the Bi-2223 HT_c superconductor system with Bi₂Sr₂Ca₂Cu_3-xEr_xO_{10+ δ} nominal composition, where x=0.5 and 1.0, by the glass-ceramic technique. Using an analysis developed for non-isothermal crystallization studies, information on some aspects of crystallization temperature and thermal properties has been obtained. The crystallization studies were made using DTA with several uniform rates. The calculations of crystallization activation energies, E_a, and the Avrami parameters, n, were made based on the non-isothermal kinetic theory of Kissinger and the Ozawa’s equations. The DTA data of the samples showed that the first crystallization temperature, T_x1, increases and the second crystallization temperature, T_x2, decreases by increasing the Er concentration. This suggests that the Er substitution had significant effect on the glassification of the BSCCO material due to change on the surface nucleation and increased ionic activities at high temperature region. The activation energy for crystallization, E_a, of the samples was also showed an increase at high Er concentration case. However, the Avrami parameter, n, decreased from 2.5 to 1.7 for x=0.5 and 1.0 samples, respectively. This suggests that the growth mechanism is diffusion-controlled and three-dimensional parabolic growth takes place near the first crystallization temperature. The oxidization rates and the activation barrier for oxygen out-diffusion process, E, was calculated using the TG data. It was found that the total mass gain in the x=0.5 sample is comparably smaller than that of the x=1.0 sample. This shows that the oxygen absorption of the x=1.0 sample is faster than the x=0.5 sample, leading to increase in the oxidization rate in the x=1.0 material.     

Selective catalytic oxidation of ammonia into nitrogen and water vapour over transition metals modified Al<Subscript>2</Subscript>O<Subscript>3</Subscript>, TiO<Subscript>2</Subscript> and ZrO<Subscript>2</Subscript>

Copper or iron supported on commercially available oxides, such as γ-Al₂O₃, TiO₂ (anatase) and monoclinic tetragonal ZrO₂ (mt-ZrO₂) were tested as catalysts for selective catalytic oxidation of ammonia into nitrogen and water vapour (NH₃-SCO) in the low temperature range. Different commercial oxides were used in this study to determine the influence of the specific surface area, acidic nature of the support and crystalline phases as well as of the type of species and aggregation state of transition metals on the catalytic performance in selective ammonia oxidation. Copper modified oxide supports were found to be more active and selective to nitrogen than catalysts impregnated with iron. Activities of both transition metal modified samples decreased in the following order: mt-ZrO₂, TiO₂ (anatase), γ-Al₂O₃. Quantitative total ammonia conversion was achieved with the Cu/ZrO₂ catalytic system at 400°C. Characterisation techniques, e.g. H₂-temperature programmed reduction, UV-VIS-diffuse reflectance spectroscopy, suggest that easily reducible copper oxide species are important in achieving high catalytic performances at low temperatures.     

Refractive Index Adjustment of SiO<Subscript>2</Subscript> Gel Glass with Zirconium Oxychloride

ZrO₂-SiO₂ binary oxide gel glasses with various Zr contents were prepared by the sol–gel method with zirconium oxychloride and tetraethoxysilane as precursors. It is found that the refractive index of mixed oxide gel glass is linear with the Zr content and suitable heat treatment will give rise to an increase in the refractive index. By employing FTIR techniques, a new Zr—O—Si bond has been investigated with part of the zirconium ions being incorporated into the silica network. The capability to tune the refractive index for the blend sample with Zr ions and to obtain a stable refractive index at relative low treatment temperature suggests that the gel glass is potential matrix for doping with near IR fluorescence organic dyes and make them promising materials for active optical waveguides.     

Influence of B<Subscript>2</Subscript>O<Subscript>3</Subscript> on the structure and crystallization of soil active glasses

Glasses of the SiO₂–P₂O₅–K₂O–MgO–CaO–B₂O₃ system acting as nutrients carriers in the soil environment were synthesised by the melt-quenching technique. Thermal properties were studied using DTA/DSC methods and the influence of B₂O₃ and P₂O₅ content on thermal stability and crystallization process of these glasses was examined. The structure of the glass network was characterized by FTIR, ³¹P, and ¹¹B MAS NMR. The chemical activity of the glasses in the 2 mass% citric acid solution was measured by the ICP-AES method. The analysis indicated that the formation of P–O–B units with chemically stable tetrahedral borate groups decreases the glass solubility in conditions simulating the soil environment.     

Thermodynamic Properties of AgIn<Subscript>2</Subscript>Te<Subscript>3</Subscript>I and AgIn<Subscript>2</Subscript>Te<Subscript>3</Subscript>Br,Determined by EMF Method

Differential thermal analysis (DTA), X-ray diffraction (XRD), and electromotive force (EMF) are used to triangulate Ag–In–Te–I(Br) systems in the vicinity of compounds AgIn₂Te₃I and AgIn₂Te₃Br. The three-dimensional position of the AgIn₂Te₃I–InTe–Ag₂Te–AgI and AgIn₂Te₃Br–InTe–Ag₃TeBr phase areas with respect to the figurative points of silver is used to create equations of potential-determining chemical reactions. The potential-determining reactions are conducted in (?)C|Ag|Ag₃GeS₃I(Br) glass|D|C(+) electrochemical cells (ECCs), where C stands for inert (graphite) electrodes, Ag and D are ECC electrodes (D denotes alloys of one-, three-, and four-phase areas), and Ag₃GeS₃I and Ag₃GeS₃Br glasses are membranes with purely ionic Ag⁺ conductivity. Linear parts of the temperature dependences of the cell EMFs are used to calculate the standard integral thermodynamic functions of saturated solid solutions based on AgIn₂Te₃I and AgIn₂Te₃Br, and the relative partial thermodynamic functions of silver in the stoichiometric quaternary compounds.     

Crystallization and microstructure of Li2O-Al2O3-SiO2 glass containing complex nucleating agent

The crystallization and microstructure of Li₂O-Al₂O₃-SiO₂ (LAS) glass ceramic with complex nucleating agents (TiO₂ + ZrO₂ + P₂O₅ +/or F⁻) are investigated by differential thermal analysis (DTA), X-ray diffraction (XRD) and scanning electron microscopy (SEM), and the effects of P₂O₅ and F⁻ on the crystallization of LAS glass are also analyzed. The introduction of both P₂O₅ and F⁻ promotes the crystallization of LAS glass by decreasing the crystallization temperature and adjusting the crystallization kinetic parameters, allows a direct formation of β-spodumene without the transformation of LiAl(SiO₃)₂ into β-spodumene and as a result, increases the crystal size and crystallinity of LAS glass ceramic.     

Viscosity and shrinkage of porous and quartzoid glasses of the Na<Subscript>2</Subscript>O-B<Subscript>2</Subscript>O<Subscript>3</Subscript>-SiO<Subscript>2</Subscript> system

Shrinkage of porous glasses on heating from 20 to 800°C was studied and temperature dependences of the viscosity in the range of 10¹¹–10¹³ P were determined for quartzoid (sintered) glasses based on five glasses with different compositions in the Na₂O-B₂O₃-SiO₂ system. The shrinkage of porous glasses and the viscosity of quartzoid glasses were analyzed in relation to their composition and temperature of preliminary thermal treatment.     

Hot atom chemical behavior of tritium in neutron-irradiated Li<Subscript>2</Subscript>TiO<Subscript>3</Subscript> and Li<Subscript>2</Subscript>ZrO<Subscript>3</Subscript>

The annihilation behavior of irradiation defects induced in neutron-irradiated Li₂TiO₃ and Li₂ZrO₃ were investigated with the tritium release behavior. It was revealed that the common characteristics in both samples were that the annihilation process of irradiation defects consisted of two first-order processes and E’-center could act as tritium trapping site, and otherwise was the way how the E’-center annihilated. The difference was suggested to attribute to the mobility of M as M⁴⁺ (or M³⁺, etc.).     

Physicochemical properties and mixed electronic and ionic conduction of composite ceramics in the system ZrO<Subscript>2</Subscript>-Bi<Subscript>2</Subscript>CuO<Subscript>4</Subscript>-Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>

Composites ZrO₂-(Bi₂CuO₄+ 20 wt % Bi₂O₃) (50–80 vol % ZrO₂) are synthesized and their physicochemical properties are studied. It is demonstrated that the composites comprise triple-phase mixtures of ZrO₂ of a monoclinic modification, Bi₂CuO₄, and solid solution Bi_2?x Zr _x O_{3 + x/2} and retain their mechanical strength up to 800°C. Impedance spectroscopy is used to examine their electroconductivity at 700–800°C in the interval of partial oxygen pressures extending from 37 to 2.1 × 10⁴ Pa. Contributions made by electronic and ionic constituents to their overall conductivity are evaluated. The best specimens’ conductivity is ～0.01 S cm^?1, with the electronic and ionic transport numbers nearly equal. The composite consisting of 50 vol % ZrO₂ and 50 vol % (Bi₂CuO₄ + 20 wt % Bi₂CuO₄) is tested in the role of an oxygen-separating membrane. The selective flux of oxygen in the temperature interval 750–800°C amounts to (2.2–6.3) × 10^?8 mol cm^?2 s^?1, testifying that these materials may be used as gas-separating membranes.     

Glass formation in the Li<Subscript>2</Subscript>O-Ta<Subscript>2</Subscript>O<Subscript>5</Subscript>-TeO<Subscript>2</Subscript> system

In the Li₂O-Ta₂O₅-TeO₂ system, the boundaries of the glass region have been determined. The electrical and spectral properties of glasses and crystalline materials have been investigated.     

Effects of gaseous hydrogenation on crystallization behavior of melt-spun Mg<Subscript>63</Subscript>Pr<Subscript>15</Subscript>Ni<Subscript>22</Subscript> amorphous ribbons

Effects of gaseous hydrogenation on crystallization behavior of melt-spun Mg₆₃Pr₁₅Ni₂₂ amorphous ribbons have been investigated. The crystallization peak temperature T _p1 shifted to higher temperature with increasing heating rate for the un-hydrogenated Mg₆₃Ni₂₂Pr₁₅ metallic glass, however, it is nearly unchanged for the hydrogenated sample. The present work indicates that the crystallization is a nucleation-and-growth process for the un-hydrogenated Mg₆₃Ni₂₂Pr₁₅ metallic glass. However, the crystallization of hydrogenated sample begins with nucleation and then diffusion-controlled growth takes place.     

Stabilization of quercetin-functionalized silica gel against hydrolysis by blocking silanol groups with TiO<Subscript>2</Subscript> or ZrO<Subscript>2</Subscript> and its application for the removal of Hg(II)

Free silanol groups of silica-gel functionalized with quercetin (QSG) were blocked with TiO₂ or ZrO₂ to produce TiO₂-QSG and ZrO₂-QSG, respectively. The silica materials were characterized by infrared, Raman spectra, thermogravimetric, elemental analyses, magic angle spinning ¹³C-nuclear magnetic resonance, BET specific surface area measurements and inductively coupled plasma—optical emission spectrometry-monitored silica hydrolysis. Siloxane groups are reinforced in the blocked QSG samples without affecting the hydrophilic nature or the porosity of silica. Quercetin is unaffected by the titania layer in contrary to zirconia. Also, the stability of silica against hydrolysis in TiO₂-QSG and ZrO₂-QSG was remarkably improved in the range of pH 3.5–9.1, attributed to the interruption of the intramolecular interaction of silanol groups with the amino groups. The hydrolyzed silica of TiO₂-QSG and ZrO₂-QSG decreased to 46.6 and 18.5%, of that of QSG and to 7.6 and 3.1%, of that of 3-aminopropylsilica gel at pH 9.1, respectively. TiO₂-QSG was applied for the extraction of Hg(II) with separation efficiency of 99.0 ± 0.6% at pH 8.5. The capacity loss of TiO₂-QSG per recovery cycle of Hg(II) was lowered in comparison with the uncovered material. It was successfully applied for the recovery of Hg(II) from spiked water and referenced samples.