Structural Investigation of Ormosils with Potential as Host Photonic Materials

Class II ormosils in the systems: methyl, propyl, vinyl and phenyl silicates have been structurally investigated for their suitability as photonic materials and this paper is a precis of many data. From visible and near-infrared spectroscopy these ormosils have: (i) intrinsic optical windows in the visible and at 1.06, 1.3 and 1.55 μm and (ii) low residual water, despite being synthesised at only 60°C. The residual water can be expelled under vacuum. Solid state²⁹Si nuclear magnetic resonance spectroscopy shows that matrix condensation increases as the organic content of the matrix is increased; this is accompanied by a decrease in BET surface area.     

Preparation of an ion-selective electrode by chemical treatment of copper wire for the measurement of copper(II) and iodide by batch and flow-injection potentiometry

The preparation of an ion-selective electrode by chemical treatment of copper wire and its application for the measurements of copper (II) and iodide ions is described. The proposed reaction mechanism at the sensing surface, which explains the response of the electrode to Cu²⁺ and iodide ions, is discussed. The prepared electrode was suitable for direct potentiometric measurements of iodide and copper (II) in batch experiments down to concentrations of 1 × 10^–5 mol L^–1. A tubular electrode, prepared in the same way, may be used as a potentiometric sensor in a flow-injection analysis for Cu (II) and/or iodide determinations. Received: 4 December 1998 / Revised: 31 March 1999 / Accepted: 6 April 1999     

Room temperature ferromagnetism in sol–gel deposited un-doped ZnO films

Dilute magnetic semiconductors are fast emerging spintronic materials where advantage of magnetic properties of semiconductor materials (usually doped with small quantities of magnetic ions) is being explored. Sol–gel technique, being low-cost simple and application oriented method, has been used in the present case. ZnO films of <150 nm thickness have been deposited by spin coating onto single crystal p-type Si substrates. The optimized sol is of paramagnetic nature, whereas, mixed para- dia-magnetic phase is observed for the as-prepared films. A complete ferromagnetic phase transition has been observed after heating the films in vacuum at a temperature of 300 °C. These sol–gel prepared films exhibit hexagonal wurtzite structure as observed by X-ray diffraction. After the magnetic field annealing in vacuum the films showed strengthened magnetic as well as structural properties. This work presents a clear evidence of ferromagnetic behavior of the un-doped ZnO films deposited by sol–gel at room temperature. It is also pointed out that Zn vacancies rather than oxygen deficiency are responsible for ferromagnetism in these sol–gel deposited ZnO thin films, whereas, the experimental evidence has been substantiated with the theoretical calculations using density functional theory.     

PVC-silica hybrids: effect of sol–gel conditions on the morphology of silica particles and thermal mechanical properties of the hybrids

Hybrid materials from poly(vinyl chloride) (PVC) and silica have been prepared using different conditions by the sol–gel technique. In situ generation of silica network in the PVC matrix was carried out by hydrolysis/condensation of tetraethoxysilane (TEOS) in the matrix. Morphology of the silica particles produced in hybrid films was studied by scattering electron microscopy. The shape of silica particle produced in the matrix was modified by carrying out the sol–gel process under steam on the hybrid films using TEOS. The films were subjected to strain conditions during this process, which produced lamellar shaped particles in the matrix. It was possible to produce platelet type of structure with different aspect ratio by changing the composition and the stress conditions on the films during the steaming process. Addition of a very small amount of γ-glycidoxypropyltrimethoxysilane as compatibilizer drastically reduced the silica particles size in the matrix to nano-level. Thermal–mechanical properties of some of these hybrids were studied and related to the composition, structure and inter-phase interaction between the silica and the matrix.     

Fiber-optic fluorescence sensor for dissolved oxygen detection based on fluorinated xerogel immobilized with ruthenium (II) complex

A fiber-optic sensor based on fluorescence quenching was designed for dissolved oxygen (DO) detection. The fluorinated xerogel-based sensing film of the present sensor was prepared from 3, 3, 3-trifluoropropyltrimethoxysilane (TFP–TriMOS). Oxygen-sensitive fluorophores of tris (2, 2′- bipyridine) ruthenium (II) (Ru(bpy)₃²⁺) were immobilized in the sensing film and the emission fluorescence was quenched by dissolved oxygen. In the sensor fabrication, a two-fiber probe was employed to obtain the best fluorescence collection efficiency and the sensing film was attached to the probe end. Scanning electron microscope (SEM), UV–Vis absorption spectroscopy (UV–Vis) and fourier transform infrared spectroscopy (FTIR) measurements have been used to characterize the sensing film. The sensor sensitivity is quantified by I _deoxy/I _oxy, where I _deoxy and I _oxy represented the detected fluorescence intensities in fully deoxygenated and fully oxygenated environments, respectively. Compared with tetramethoxysilane (TMOS) and methyltriethoxysilane (MTMS)-derived sensing films, TFP–TriMOS-based sensor exhibited excellent performances in dissolved oxygen detection with short response time of 4 s, low limit of detection (LOD) of 0.04 ppm (R.S.D. = 2.5%), linear Stern–Volmer calibration plot from 0 to 40 ppm and long-term stability during the past 10 months. The reasons for the preferable performances of TFP–TriMOS-based sensing film were discussed.     

Mechanical properties of ormosils

Many organically modified silicates (ormosils) can be prepared by the sol-gel method with very different mechanical properties by varying the ratio of polydimethylsiloxane (PDMS) to tetraethoxysilane (TEOS) contents and processing conditions. With a low PDMS concentration, the ormosils are harder, stiffer and stronger than those with higher concentration of PDMS. Even harder ormosils are possible when ultrasonic irradiation is used during synthesis. As the PDMS concentration is increased, the ormosils take on a more flexible nature, and over a critical concentration actually become rubbery. These new rubbery materials can contain as much as 75% inorganic components, and have more stable mechanical properties than commercial rubbers at elevated temperatures. Effects of PDMS addition to the network structure and mechanical properties of the ormosils were investigated.     

High optical transparency and low dielectric constant of novel organosoluble poly(ether ketone amide)s derived from an unsymmetrical diamine containing trifluoromethyl and methyl pendant groups

A series of novel fluorinated poly(ether ketone amide)s (PEKAs) were prepared from an unsymmetrical aromatic diamine, (4′-(4″-amino-2″-trifluoromethylphenoxy)-3′,5′-dimethylphenyl)(4-aminophenyl)-methanone (1), with various aromatic dicarboxylic acids using the phosphorylation polycondensation technique. The PEKAs had inherent viscosities ranging from 0.43 to 0.65 dl/g. All the fluorinated PEKAs could be soluble in many polar organic solvents such as N-methyl-2-pyrrolidinone (NMP), N,N′-dimethylacetamide (DMAc), N,N′-dimethylformamide (DMF), dimethyl sulfoxide (DMSO), and tetrahydrofuran (THF). Flexible and tough polymer films could be prepared by casting from DMAc solvent. The PEKA films exhibited high optical transparency with a cutoff wavelength of 354–365 nm and good mechanical properties with tensile strengths of 78–98 MPa and elongations at break of 11.5–18.5%. They showed glass-transition temperatures in the range of 288−323 °C and the onset decomposition temperatures in the range of 450−461 °C in nitrogen atmosphere. Meanwhile, the PEKA films possessed low dielectric constants of 1.98–2.71 at 1 MHz and low moisture absorption (<2%). Due to their properties, the fluorinated PEKAs could be considered as photoelectric and microelectronic materials.     

On the use of plant cellulose nanowhiskers to enhance the barrier properties of polylactic acid

Polylactic acid (PLA) nanocomposites were prepared using cellulose nanowhiskers (CNW) as a reinforcing element in order to asses the value of this filler to reduce the gas and vapour permeability of the biopolyester matrix. The nanocomposites were prepared by incorporating 1, 2, 3 and 5 wt% of the CNW into the PLA matrix by a chloroform solution casting method. The morphology, thermal and mechanical behaviour and permeability of the films were investigated. The CNW prepared by acid hydrolysis of highly purified alpha cellulose microfibers, resulted in nanofibers of 60–160 nm in length and of 10–20 nm in thickness. The results indicated that the nanofiller was well dispersed in the PLA matrix, did not impair the thermal stability of this but induced the formation of some crystallinity, most likely transcrystallinity. CNW prepared by freeze drying exhibited in the nanocomposites better morphology and properties than their solvent exchanged counterparts. Interestingly, the water permeability of nanocomposites of PLA decreased with the addition of CNW prepared by freeze drying by up to 82% and the oxygen permeability by up to 90%. Optimum barrier enhancement was found for composites containing loadings of CNW below 3 wt%. Typical modelling of barrier and mechanical properties failed to describe the behaviour of the composites and appropriate discussion regarding this aspect was also carried out. From the results, CNW exhibit novel significant potential in coatings, membranes and food agrobased packaging applications.     

Oxygen and oil barrier properties of microfibrillated cellulose films and coatings

The preparation of carboxymethylated microfibrillated cellulose (MFC) films by dispersion-casting from aqueous dispersions and by surface coating on base papers is described. The oxygen permeability of MFC films were studied at different relative humidity (RH). At low RH (0%), the MFC films showed very low oxygen permeability as compared with films prepared from plasticized starch, whey protein and arabinoxylan and values in the same range as that of conventional synthetic films, e.g., ethylene vinyl alcohol. At higher RH’s, the oxygen permeability increased exponentially, presumably due to the plasticizing and swelling of the carboxymethylated nanofibers by water molecules. The effect of moisture on the barrier and mechanical properties of the films was further studied using water vapor sorption isotherms and by humidity scans in dynamic mechanical analysis. The influences of the degree of nanofibrillation/dispersion on the microstructure and optical properties of the films were evaluated by field-emission scanning electron microscopy (FE-SEM) and light transmittance measurements, respectively. FE-SEM micrographs showed that the MFC films consisted of randomly assembled nanofibers with a thickness of 5–10 nm, although some larger aggregates were also formed. The use of MFC as surface coating on various base papers considerably reduced the air permeability. Environmental scanning electron microscopy (E-SEM) micrographs indicated that the MFC layer reduced sheet porosity, i.e., the dense structure formed by the nanofibers resulted in superior oil barrier properties.     

Preparation of Nanostructured Magnetic Films by the Plasma Jet Technique

 Magnetic films were prepared by the plasma jet technique from Fe, mumetal, and Fe/Hf or Fe/Ta nozzles. Two different plasma jet systems with different vacuum pumps were used to compare the quality of the produced films. The films prepared from a Fe nozzle in the two different equipments shows that oxygen in the residual atmosphere of the low vacuum reactor leads mainly to the formation of iron oxides. The Fe and mumetal films prepared in the high vacuum system contain only a very small amount of oxygen, as proved by chemical analysis and ferromagnetic resonance. The mumetal film, moreover, shows good soft magnetic properties and low magnetic damping. For the reactive plasma jet deposition of nanogranular Fe–Hf–O and Fe–Ta–O films, the low vacuum system was used. The films with higher oxygen content exhibit tunneling-type conductivity. In some films, superparamagnetic behaviour and spin-dependent tunneling magnetoresistance were observed.     

Preparation of Nanostructured Magnetic Films by the Plasma Jet Technique

Summary.  Magnetic films were prepared by the plasma jet technique from Fe, mumetal, and Fe/Hf or Fe/Ta nozzles. Two different plasma jet systems with different vacuum pumps were used to compare the quality of the produced films. The films prepared from a Fe nozzle in the two different equipments shows that oxygen in the residual atmosphere of the low vacuum reactor leads mainly to the formation of iron oxides. The Fe and mumetal films prepared in the high vacuum system contain only a very small amount of oxygen, as proved by chemical analysis and ferromagnetic resonance. The mumetal film, moreover, shows good soft magnetic properties and low magnetic damping. For the reactive plasma jet deposition of nanogranular Fe–Hf–O and Fe–Ta–O films, the low vacuum system was used. The films with higher oxygen content exhibit tunneling-type conductivity. In some films, superparamagnetic behaviour and spin-dependent tunneling magnetoresistance were observed. Received October 5, 2001. Accepted November 22, 2001     

Mo<Subscript>6</Subscript>Cl<Subscript>12</Subscript>-Incorporated Sol-Gel for Oxygen Sensing Applications

Excitation of hexanuclear molybdenum complexes such as Mo₆Cl₁₂ and its derivatives in the ultraviolet results in a strongly red-shifted luminescence centered at 750nm. Since oxygen efficiently quenches the luminescence, these thermally stable inorganic complexes are candidate lumophores for real-time, high temperature optical fiber based sensing of oxygen. Sol-gel films containing the acetonitrile complex of Mo₆Cl₁₂ were deposited on quartz substrates by dip coating. After drying, the films were heated at 200^∘C for 1 h. The luminescence lineshapes of films before and after heating were unchanged, indicating that heating did not adversely affect the cluster photophysics. Compared to solutions of the acetonitrile complex, quenching by oxygen was smaller in the as-prepared films, but heating at 200^∘C for 1 h increased the quenching, apparently due to increased oxygen permeability resulting from the loss of water or other small molecules from the matrix. These results confirm the potential of hexanuclear molybdenum complexes such as Mo₆Cl₁₂⋅2CH₃CN as the lumophores in fiber optic oxygen sensors that can operate up to 200^∘C.     

Semiconducting properties of polypyrrole films in aqueous solution

The influence of the nature of the anions on the conductivity of polypyrrole films in aqueous solution was investigated by photocurrent spectroscopy combined with electrochemical impedance spectroscopy in dependence on the potential. As demonstrated, the conductivity of polypyrrole films at negative potentials can vary from a semiconducting to an ionic conducting state, depending on the size of the charge-compensating counter-anion incorporated during the electropolymerization. The reduced polypyrrole shows semiconducting properties when small anions are inserted, releasing the polymer matrix during the reduction process. The polymer can than be considered as a two-layer system, consisting of a semiconducting layer and a porous layer. Measurements at different thickness of polypyrrole films have shown that the position of the semiconducting layer is in the electrode/polymer interface. The ohmic resistance of the semiconducting layer is in the range 1–5 kΩ, the capacitance approaches a value of 100–500 nF and the flatband potential is −0.62 V_SCE. If large anions are incorporated, cation insertion takes place during reduction, the electrolyte content in the polymer then is relatively high and the polymer's behaviour is similar to that of an ionic conductor. The results are presented and discussed together with the example of methylsulfonate as a relatively small anion and polystyrenesulfonate as a large anion. Received: 28 July 1998 / Accepted: 22 February 1999     

Photopolymerized silver-containing conducting polymer films. Part II. Physico-chemical characterization and mechanism of photopolymerization process

Physico-chemical and mechanical characterizations of nanophase silver-containing polypyrrole films prepared using a new photopolymerization process were performed. In general, the recorded physical, chemical, and mechanical data characteristic of these films was similar to corresponding literature data obtained from electropolymerized or chemically polymerized polypyrrole. However, photopolymerized polypyrrole films possessed an unusually high anion-to-monomer ratio of 0.8:1. Also, the photopolymerized material contained silver nanoparticles, having diameters of 2 μm or less, uniformally distributed throughout the polymer matrix. While the photopolymerization mechanism is complex, it is suggested that a pyrrole–silver cation complex is most likely the key component involved in the photopolymerization initiation step. Paper submitted for inclusion in the special issue of the Journal of Solid State Electrochemistry honoring the 85th birthday of Professor John O’M. Bockris.     

Nafion-based solid-state gas sensors: Pt / Nafion electrodes prepared by an impregnation-reduction method in sensing oxygen

The influences of the reductant concentration of NaBH₄ and the quantity of Pt loading on the active surface area and the sensitivity of the Pt/Nafion electrodes prepared by an impregnation-reduction method in detecting oxygen were investigated in this study. The Pt/Nafion electrodes with a Pt loading of 4.99 mg/cm², obtained at 0.0107 M Pt(NH₃)₄Cl₂ and 0.06 M NaBH₄, show maximum sensitivities of 0.0528 A/ppm and 0.0538 A/ppm obtained in O₂ concentration regions of 0–5000 and 5000–50 000 ppm, respectively. A sensing model was also proposed to illustrate the sensing phenomenon. Received: 21 January 1998 / Accepted: 10 March 1998     

Preparation of photocurable silica–titania hybrid coatings by an anhydrous sol–gel process

Photocurable silica-titania hybrid coatings were prepared through an anhydrous sol–gel process. Moreover, test samples were prepared by the addition of definite ratios of fluoro acrylate oligomers into the formulations to manage the optical properties of transmitted light. Formulations were applied to corona-treated polycarbonate substrates. Upon adding the inorganic component to the coating material, thermal, mechanical, and other properties, such as hardness, gloss, contact angle, and flame resistance were improved. The photocured hybrid films showed an increase in the refractive index with increasing the titanium tetraisopropoxide content. As expected, a decrease was observed in the refractive index of the coatings with the incorporation of fluoro acrylate resin. The surface morphology of the hybrid films was characterized by ESEM analysis. In addition the chemical composition of the surface of the coatings was identified by ESEM–EDS technique. ESEM studies indicated that inorganic particles were dispersed homogenously throughout the organic matrix.     

Preparation and evaluation of a functionalized polymer-coated silica based sorbent for metal ion separation

A silica based sorbent with an anion complexone polymer coating, [24]ane-N₆ macrocycle, was prepared. The chelation properties of this material were investigated by elemental analysis, infrared spectra and Voige’s method. The polymer-coated silica column (25– 40 μm, 100 × 4.6 mm i.d.) was employed for trace metal analyses. Oxalic acid, malonic acid, succinic acid, citric acid, phthalic acid and acetic acid were used as mobile phases. Their retention characteristics were elucidated. Oxalic acid was found to be the most effective eluent. With a mobile phase consisting of oxalic acid (25 mM) and sodium nitrate (25 mM) at pH 4.2, the separation of copper(II), cadmium(II), cobalt(II) and zinc(II) in sea water could be achieved. The identification of metal ions was performed at 510 nm using 4(2-pyridylazo)resorcinol (1 × 10^–4 M) as post column reagent. The limits of detection were 5 × 10^–7 M, 1 × 10^–5 M, 3 × 10^–5 M and 2 × 10^–6 M for copper(II), cadmium(II), cobalt(II) and zinc(II) based on three times the standard deviation of the response for the lowest concentration (n = 5) in the chromatogram with a sample volume of 50 μL. For evaluation of data reliability, oyster tissue (NIST SRM 1566 a) was studied with the proposed system. Received: 9 February 1998 / Revised: 15 May 1998 / Accepted: 16 June 1998     

Copper Incorporated [Me2(15)dieneN4] Macrocyclic Complex for Fabrication of PVC based Membrane Electrode for Copper

Copper (II) complex of 2,4-dimethyl-1,5,9,12-tetraazacyclopentadeca-1,4-diene, [Me₂(15)dieneN₄] was synthesized and used in the fabrication of Cu²⁺ – selective ISE membrane in PVC matrix. The membrane having Cu(II) macrocyclic complex as electroactive material along with sodium tetraphenyl borate (NaTPB) as anion discriminator. Dibutyl phthalate (DBP) as plasticizer in poly(vinyl chloride) (PVC) matrix was prepared for the determination of Cu²⁺. The best performance was observed by the membrane having Cu(II) complex–PVC–NaTPB–DBP with composition 1:5:1:3. The sensor worked well over a concentration range 1.12 × 10⁻⁶ M–1.0 × 10⁻¹ M between pH 2.1–6.2 and a fast response time 10±2 s and a lifetime of 6 months. Their performance in partially non-aqueous medium was found satisfactory. Electrodes exhibited excellent selectivity for Cu²⁺ ion over other mono-, di-, trivalent cations. It can also be used as indicator electrode in the potentiometric titration of Cu²⁺ against EDTA as well as in the determination of Cu²⁺ in real samples.     

Optical and electrochemical sol-gel sensors for inorganic species

The use of sol-gels as a sensing matrix for the development of unique sensing strategies is discussed. Sol-gels offer almost limitless possibilities for sensing substrates due to the variety of physical properties that can be obtained by altering a number of discussed fabrication conditions and techniques. By careful consideration of the sensing requirements, novel detection methods have been developed for a variety of analytes and applications. Here, sol-gels have been used to monitor pH at the extreme ends of the scale ([H⁺] = 1–11 M and [OH⁻] = 1–10 M) and in mixed solvent/solute systems using dual sensing approaches. The use of ligand-grafted sol-gel monoliths for optical determination of metal ion species is also discussed. The electrochemical determination of Cr(VI) by electrodeposited sol-gel modified electrodes is also presented.     

Thermal and mechanical properties of fluoroaramid-silica nanocomposites

Fluoroaramids have been used as an attractive matrix polymer for composites due to their excellent mechanical and surface properties. Properties of these polymers can be improved further by dispersing silica in these matrices at a nano-scale via the sol–gel process. The role of interfacial interaction on the thermal and mechanical properties in such hybrids has been investigated in the present work. Two types of hybrids have been prepared; one using the aramid matrix with pendant alkoxy groups on the chain and other without. Silica network was developed by addition of tetraethoxysilane and its subsequent hydrolysis and condensation in the polymer matrix. Well dispersed inorganic domains of nanometer scale were obtained in case of matrix with pendant alkoxy groups on the chain, which showed larger increase in the α- and β-relaxation temperatures, storage modulus and thermal stability as compared to the matrix without alkoxy groups. The role of interfacial interaction, and its effect on properties on the fluoroaramid-silica hybrid composites has been discussed.