Solvothermal synthesis of WO3/TiO2/carbon fiber composite photocatalysts for enhanced performance under sunlight illumination

Carbon fiber (CF)‐based WO₃/TiO₂ composite catalysts (WO₃/TiO₂/CF) were successfully synthesized by solvothermal method. The catalysts were characterized by XPS, SEM, BET, XRD, FTIR, Raman and UV–Vis. The analyses confirmed the WO₃/TiO₂ nanoparticles with high crystallinity deposited on the carbon structure. The photocatalytic degradation of Orange II azo dye under UV and sunlight illumination with the synthesized catalyst was explored. The composite catalyst displayed high performance (85%) for Orange II degradation while that of for WO₃/TiO₂ was found as 76%. The effects of CF amount, solution pH, initial dye concentration and catalyst dose on photocatalytic performance were studied. It was found that the degradation efficiency increased from 68% to 90% with the increasing CF amount from 3 wt% to 5 wt%, while the further increase in CF amount (7–10 wt%) decreased the photodegradation due to the blocking the active sites of WO₃/TiO₂. The enhanced photocatalytic efficiency was mainly attributed to the electrical properties of the CF and reduced bandgap.     

Preparation of SnO2–TiO2/Fly Ash Cenospheres and its Application in Phenol Degradation

SnO₂–TiO₂/fly ash cenospheres (FAC) were prepared via hydrothermal method and used as an active photocatalyst in a photocatalytic system. Scanning electron microscopy, X‐ray diffraction analysis, UV–Vis diffuse reflectance spectroscopy, Fourier transform infrared spectroscopy and N₂ adsorption–desorption measurements were used to determine the structure and optical property of SnO₂–TiO₂/FAC. Phenol was selected as the model substance for photocatalytic reactions to evaluate catalytic ability. Results showed that the degradation efficiency of phenol by SnO₂–TiO₂/FAC was 90.7% higher than that decomposed by TiO₂/FAC. Increased efficiency could be due to the enhanced synergistic effect of semiconductors and FAC could provide more adsorption sites for the pollutant in the photocatalytic reaction. Furthermore, SnO₂–TiO₂/FAC composites exhibited excellent photocatalytic stability in four reuse cycles. Radical‐trapping experiments further revealed the dominating functions of holes in the photocatalytic reaction.     

An electronic tongue using potentiometric all-solid-state PVC-membrane sensors for the simultaneous quantification of ammonium and potassium ions in water

The simultaneous determination of NH₄⁺ and K⁺ in solution has been attempted using a potentiometric sensor array and multivariate calibration. The sensors used are rather non-specific and of all-solid-state type, employing polymeric (PVC) membranes. The subsequent data processing is based on the use of a multilayer artificial neural network (ANN). This approach is given the name "electronic tongue" because it mimics the sense of taste in animals. The sensors incorporate, as recognition elements, neutral carriers belonging to the family of the ionophoric antibiotics. In this work the ANN type is optimized by studying its topology, the training algorithm, and the transfer functions. Also, different pretreatments of the starting data are evaluated. The chosen ANN is formed by 8 input neurons, 20 neurons in the hidden layer and 2 neurons in the output layer. The transfer function selected for the hidden layer was sigmoidal and linear for the output layer. It is also recommended to scale the starting data before training. A correct fit for the test data set is obtained when it is trained with the Bayesian regularization algorithm. The viability for the determination of ammonium and potassium ions in synthetic samples was evaluated; cumulative prediction errors of approximately 1% (relative values) were obtained. These results were comparable with those obtained with a generalized regression ANN as a reference algorithm. In a final application, results close to the expected values were obtained for the two considered ions, with concentrations between 0 and 40 mmol L^–1.     

Comparison of photocatalysis degradation of 4-nitrophenol using N,S co-doped TiO2 nanoparticles synthesized by two different routes

The photocatalytic degradation of 4-nitrophenol as pollutant in aqueous solutions was investigated under visible light irradiation over two different N?CS-codoped anatase TiO₂ catalysts prepared by sol?Cgel methods using titanium isopropoxide and titanium tetrachloride as two different precursors. The catalysts were characterized by XRD, SEM, DRS, EDAX and FT-IR. The effects of various operating parameters including the initial concentration of 4-nitrophenol (2?C14?ppm), solution pH (5?C8) and kinetic reactions were studied. The optimum solution pH was at around 6. For comparison purpose, the photodegradation activity of the commercial Degussa P-25 TiO₂ catalyst has also been studied. The results indicated that photocatalytic activity of N?CS-codoped TiO₂ with titanium isopropoxide as precursor was higher than N?CS-codoped TiO₂ with titanium tetrachloride as precursor and Degussa P-25.     

UV-assisted degradation of propiconazole in a TiO2 aqueous suspension: identification of transformation products and the reaction pathway using GC/MS

Photocatalytic degradation of propiconazole, a triazole pesticide, in the presence of titanium dioxide (TiO₂) under ultraviolet (UV) illumination was performed in a batch type photocatalytic reactor. A full factorial experimental design technique was used to study the main effects and the interaction effects between operational parameters in the photocatalytic degradation of propiconazole in a batch photo-reactor using the TiO₂ aqueous suspension. The effects of catalyst concentration (0.15–0.4 gL^?1), initial pH (3–9), initial concentration (5–35 mg L^?1) and light conditions were optimised at a reaction time duration of 90 min by keeping area/volume ratio constant at 0.919 cm² mL^?1. Photocatalytic oxidation of propiconazole showed 85% degradation and 76.57% mineralisation under UV light (365 nm/30 Wm^?2) at pH 6.5, initial concentration 25 mg L^?1 and constant temperature (25 ± 1 °C). The Langmuir–Hinshelwood kinetic model has successfully elucidated the effects of the initial concentration on the degradation of propiconazole and the data obtained are consistent with the available kinetic parameters. The photocatalytic transformation products of propiconazole were identified by using gas chromatography–mass spectrometry (GC/MS). The pathway of degradation obtained from mass spectral analysis shows the breakdown of transformation products into smaller hydrocarbons (m/z 28 and 39).     

Preparation and characterization of ZnTiO<Subscript>3</Subscript>–TiO<Subscript>2</Subscript>/pillared montmorillonite composite catalyst for enhanced photocatalytic activity

ZnTiO₃–TiO₂/organic pillared montmorillonite (pMt) composite catalyst was successfully prepared in this paper by immobilizing ZnTiO₃–TiO₂ onto pMt. The composition and texture of the prepared composite catalyst were characterized by X-ray diffraction, Raman spectroscopy, Fourier transform infrared spectroscopy, transmission electron microscopy, energy dispersive spectrometry, ultraviolet–visible light (UV–Vis) diffuse reflectance spectroscopy and X-ray photoelectron spectroscopy. The photocatalytic activity was tested via photocatalytic degradation of methyl blue (MB) under both visible irradiation and UV light. The results indicated that the ZnTiO₃–TiO₂/pMt composite catalyst had an apparent absorption at the area of visible irradiation, and exhibited a higher efficiency of photocatalytic degredation of MB under visible irradiation. This was due to the heterostructure of ZnTiO₃–TiO₂, and the mesoporous structure and specific surface area of the ZnTiO₃–TiO₂/pMt composite. In addition, the results of the radical scavenging experiments showed that the holes and superoxide radicals are responsible for the degradation of MB under visible irradiation.     

Sunlight-induced photocatalytic degradation of acetaminophen over efficient carbon doped TiO2 (CTiO2) nanoparticles

Carbon doped titanium oxide (CTiO₂) photocatalyst was successfully synthesized by the sol–gel method. The crystal structure, surface morphology, and optical properties of CTiO₂ have been characterized by X-ray diffraction, Brunauer–Emmett–Teller surface area (S_BET), scanning electron microscope, UV–Vis, X-ray spectroscopy (EDS), Fourier transform infrared and X-ray photoelectron spectroscopy. The photocatalytic degradation of acetaminophen (AMP) in aqueous solution, seawater, and polluted seawater has been investigated by using the synthesized photocatalyst under irradiation of UV and natural sunlight. The effectiveness of CTiO₂ compared to pure TiO₂ toward the photocatalytic removal of AMP was significantly observed. The optimized conditions including catalyst dose, initial concentration of AMP and solution pH were also studied for effective photocatalytic removal. The highest degradation rate was obtained when 2.0 g L^?1 of the catalyst was used at pH 7. The kinetic results revealed that the photocatalytic degradation of AMP using CTiO₂ obeyed a pseudo-first-order reaction kinetics.

     

Photochemical degradation of an anionic surfactant by TiO<Subscript>2</Subscript> nanoparticle doped with C,N in aqueous solution

Novel C,N-doped TiO₂ nanoparticles were prepared by a solid phase reaction. The catalyst was characterized by X-ray powder diffraction (XRD), transmission electron microscopy (TEM) and energy dispersive X-ray spectroscopy (EDX). The results showed that crystallite size of synthesized C,N-doped TiO₂ particles were in nanoscale. UV light photocatalytic studies were carried out using sodium naphthalenesulfonate formaldehyde condensate (SNF) as a model pollutant. The effects of initial concentration of surfactant, catalyst amount, pH, addition of oxidant on the reaction rate were ascertained and optimum conditions for maximum degradation was determined. The results indicated that for a solution of 20 mg/L of SNF, almost 98.7% of the substance were removed at pH ~ 4.0 and 0.44 g/L photocatalyst load, with addition of 1 mM K₂S₂O₈ and irradiation time of 90 min. The kinetics of the process was studied, and the photodegradation rate of SNF was found to obey pseudo-first-order kinetics equation represented by the Langmuir–Hinshelwood model.     

Thermal and photocatalytic behavior of Ti/LDH nanocomposites

The development of nanocomposite photocatalyst based on layered double hydroxides (LDHs) associated with TiO₂ was the subject of this research. The thermally activated Zn–Al LDHs were selected as catalyst support precursor because of their proven photocatalytic activity and therefore their possible contribution to overall activity of novel Ti–Zn–Al nanocomposite. The catalyst precursor (Zn–Al LDH) was synthesized by low supersaturation coprecipitation method, and its association with active TiO₂ component targeting the formation of novel Ti–Zn–Al nanocomposite was achieved by wet impregnation. Simultaneous thermal analysis (TG–DTA) was used to investigate the thermal behavior of Zn–Al LDH and Ti–Zn–Al LDHs. Complementary, morphology, texture, and structure characterization was carried out. The photocatalytic test reaction was performed under UV light using the methylene blue degradation. The results confirmed a successful impregnation of TiO₂ on catalyst support precursor Zn–Al–LDH followed by considerable change in morphology and structure of Zn–Al LDH precursor. It was concluded that the synergic effect between TiO₂ and Zn–Al LDH precursor contributes to the overall photocatalytic activity.     

Multi-objective simultaneous prediction of waterborne coating properties

Multi-objective simultaneous prediction of waterborne coating properties was studied by the neural network combined with programming. The conditions of network with one input layer, three hidden layers and one output layer were confirmed. The monomers mass of BA, MMA, St and pigments mass of TiO₂ and CaCO₃ were used as input data. Four properties, which were hardness, adhesion, impact resistance and reflectivity, were used as network output. After discussing the hidden layer neurons, learn rate and the number of hidden layers, the best net parameters were confirmed. The results of experiment show that multi-hidden layers was advantageous to improve the accuracy of multi-objective simultaneous prediction. 36 kinds of coating formulations were used as the training subset and 9 acrylate waterborne coatings were used as testing subset in order to predict the performance. The forecast error of hardness was 8.02% and reflectivity was 0.16%. Both forecast accuracy of adhesion and impact resistance were 100%.     

超临界 CO2 辅助制备 TiO2 外负载火山岩复合体及其光催化降解亚甲基蓝性能

 以钛酸丁酯为前驱体, 封堵的火山岩为载体, 通过超临界 CO₂ 辅助制备了 TiO₂ 外负载火山岩复合体, 并将其用于光催化降解亚甲基蓝反应, 考察了溶液 pH 值及催化剂浓度对反应性能的影响. 结果表明, TiO₂ 外负载火山岩复合体的光催化性能优于纯 TiO₂ 和 TiO₂ 体负载火山岩复合体. 这是由于外负载复合体对亚甲基蓝的高吸附性、小晶粒尺寸的 TiO₂ 颗粒以及吸附和光催化降解间的协同效应. 亚甲基蓝浓度为 1.5 mg/L, 溶液 pH 为 8, 催化剂浓度为 6.8 mg/L 时, 外负载 TiO₂ 火山岩复合体上亚甲基蓝降解速率最高, 且使用后的催化剂仍具有高的光催化活性.     

Modification of the Optical and Electronic Properties of TiO<Subscript>2</Subscript> By N Anion-Doping for Augmentation of the Visible Light Assisted Photocatalytic Performance

In this work, a nitrogen-doped anatase TiO₂ nanocrystal is prepared by a modified sol-gel preparation method using the nonionic surfactant (polyoxyethylene sorbitan monooleate) as a structural controller and a soft template. The as-prepared samples are characterized by X-ray diffraction, Raman spectroscopy, UVVis diffuse reflectance spectroscopy, and X-ray photoelectron spectroscopy techniques. Then the photocatalytic activity of these samples is assessed by the photocatalytic oxidation of phenol under visible light irradiation. The phenol concentration is measured using a UV-Vis spectrometer. Experimental results show that N-doping leads to an excellent visible light photocatalytic activity of the TiO₂ nanocatalyst. Furthermore, the formation energy and electronic structure of pure and N-doped anatase TiO₂ are described by density functional theory (DFT) calculations. It is found that N-doping narrowed the band gap of bare TiO₂, which leads to an excellent visible light photocatalytic activity of N–TiO₂ nanocatalysts. Therefore, the prepared N–TiO₂ photocatalyst is expected to find the use in organic pollutant degradation under solar light illumination.     

Hierarchical TiO2 nanosheet‐assembled nanotubes with dual electron sink functional sites for efficient photocatalytic degradation of rhodamine B

A novel Pt–TiO₂/Ag nanotube photocatalyst has been synthesized successfully via a facile method. TiO₂ nanotubes are assembled with numerous ultrathin TiO₂ nanosheets and show a highly open structure. The gaps between adjacent TiO₂ nanosheets can serve as channels for the access of reactants, accelerating the mass transfer process. During the fabrication process of the Pt–TiO₂/Ag nanotube photocatalyst, high‐quality Pt–SiO₂ nanotubes are synthesized first with the structure‐directing effect of polyvinylpyrrolidone. Then a TiO₂ layer is coated on the outside surface of the silica nanotubes. The introduced titanium species can be converted into TiO₂ nanosheet structure during the subsequent hydrothermal treatment, gradually constructing nanosheet‐assembled nanotubes. Lastly, after the introduction of another electron sink function site of Ag through UV irradiation, the Pt–TiO₂/Ag nanotube photocatalyst with dual electron sink functional sites is obtained. The specially doped Pt and Ag NPs can simultaneously inhibit the recombination process of photogenerated charge carriers and increase light utilization efficiency. Therefore, the as‐synthesized Pt–TiO₂/Ag nanotube catalyst exhibits a high photocatalytic degradation performance for rhodamine B of 0.2 min^?1, which is about 3.2 and 5.3 times as high as that of Pt–TiO₂ and TiO₂ nanotubes because of the enhanced charge carrier separation efficiency. Furthermore, in the unique nanoarchitecture, the nanotubes are assembled with numerous ultrathin TiO₂ nanosheets, which can absorb abundant active species and dye molecules for photocatalytic reaction. On the basis of experimental results, a possible rhodamine B degradation mechanism is proposed to explain the excellent photocatalytic efficiency of the Pt–TiO₂/Ag nanotube photocatalyst.     

Antibacterial inactivation of spiramycin after titanium dioxide photocatalytic treatment

The photocatalytic degradation of an antibiotic (spiramycin) has been studied using immobilized titanium dioxide (TiO₂) as a photocatalyst in a laboratory reactor under ultraviolet illumination (365 nm). The degradation of the antibiotic was monitored by ultraviolet spectrophotometry and high-pressure liquid chromatography and confirmed by an antibacterial activity evaluation. Two types of TiO₂ (P25 and PC500) immobilized on glass plates were compared. For TiO₂ PC500 immobilization on glass and paper was also studied. A slightly better degradation was obtained with TiO₂ P25 for which the degradation kinetics were investigated. The Langmuir–Hinshelwood kinetic model is satisfactorily obeyed at initial time and in the course of the reaction. Adsorption and apparent rate constants were determined. These results show a complete degradation of spiramycin, which was confirmed by the inhibition of the antibacterial activity of Staphylococcus xylosus, when exposed to spiramycin solutions treated with photocatalyst for a short time. In addition, the codegradation of spiramycin and tylosin was investigated and showed that tylosin had a higher affinity to the catalyst TiO₂ P25 than spiramycin. The complete degradation of spiramycin confirms the feasibility of such a photocatalytic treatment process for spiramycin elimination from contaminated water.     

可磁分离二氧化钛光催化剂的制备及其光催化性能

通过液相催化相转化的方法制备了一种可磁分离的光催化剂TiO₂/SiO₂/NiFe₂O₄(TSN),这种光催化剂显示出了超顺磁性,能够通过外加磁场方便的实现催化剂在水中的分离与回收。该光催化剂的X-射线衍射和TEM结果表明：纳米TiO₂颗粒包裹在磁性颗粒-SiO₂/NiFe₂O₄(SN)的周围形成TiO₂层。利用光催化降解甲基橙的效果来考察了这种光催化剂的活性,结果表明：在NiFe₂O₄和TiO₂之间包覆一层无定型的SiO₂,可以显著的提高催化剂的脱色效果,3次循环后,仍能保持良好的催化活性。     

Synthesis of TiO2 on different substrates by chemical vapor deposition for photocatalytic reduction of Cr(VI) in water

TiO₂ loaded on several substrates such as carbon fiber, aluminum plate, silica plate, and glass plate was prepared using the chemical vapor deposition (CVD) method for the photocatalytic reduction of Cr(VI) in water with the presence of ethanol under Ultraviolet (UV) illumination. As‐prepared samples were characterized by X‐Ray Diffraction (XRD), X‐ray photoelectron spectroscopy (XPS), Brunauer–Emmett–Teller (BET), and scanning electron microscopy (SEM). The catalyst with TiO₂ loaded on carbon fiber possessed an extremely large surface area (1,463,91 m²/g), while the other catalysts possessed small surface areas (0.05–0.21 m²/g). The photocatalytic activity of TiO₂ loaded on carbon fiber, which was determined by the conversion of Cr(VI) and the degradation of chemical oxygen demand (COD), was much higher than that of other catalysts. The reusability of TiO₂ loaded on carbon fiber catalyst exhibited almost the same activity as the fresh catalyst. The results indicated that TiO₂ loaded on carbon fiber is feasible for practical application.     

Kinetics of heterogeneous photocatalytic decomposition of monuron over anatase titanium dioxide powder

The photocatalytic degradation of Monuron (3-(4-chlorophenyl)-1-1-dimethylurea) in aqueous TiO₂ dispersions irradiated in the near-UV region has been investigated by using a Pyrex batch photoreactor. The Monuron and total organic carbon concentrations were determined; several reaction intermediates were also identified using HPLC. The influence on the degradation kinetics of the initial Monuron concentration, of the TiO₂ concentration, and of the initial pH of dispersion was studied. A pseudo-first order kinetics of Langmuir-Hinshelwood type was found to satisfactorily describe the Monuron degradation. The mineralization of the pollutant was virtually complete in the 3–9 pH range while at pH = 1.0 and 11.0 only a partial mineralization was reached even after a long irradiation time. The quantum yield values of Monuron degradation were determined by measuring the photon flow transmitted by the dispersion and applying a macroscopic photon balance on the photoreactor. The quantum yields were found to increase by increasing the pH of the dispersion.     

Determination of bifonazole and identification of its photocatalytic degradation products using UPLC‐MS/MS

The main goal of the presented work was to investigate the effect of ZnO or/and TiO₂ on the stability of bifonazole in solutions under UVA irradiation. To this end, a simple and reproducible UPLC method for the determination of bifonazole in the presence of its photocatalytic degradation products was developed. Linearity was studied in the range of 0.0046–0.15 mg mL⁻¹ with a determination coefficient of 0.9996. Bifonazole underwent a photocatalytic degradation process under the experimental conditions used. Comparative studies showed that combination of TiO₂/ZnO (1:1 w /w) was a more effective catalyst than TiO₂ or ZnO with a degradation rate of up to 67.57% after 24 h of irradiation. Further, kinetic analyses indicated that the photocatalytic degradation of bifonazole in the mixture of TiO₂/ZnO can be described by a pseudo‐first order reaction. Statistical comparison clearly indicated that the presence of TiO₂/ZnO also affected the stability of bifonazole from a cream preparation after 15 h of UVA exposure (p < 0.05). Ten photodegradation products of bifonazole were identified for the first time and their plausible fragmentation pathways, derived from MS/MS data, were proposed. The main pathway in the photocatalytic transformation of bifonazole in the presence of ZnO or/and TiO₂ involves hydroxylation of the methanetriyl group and/or adjacent phenyl rings and cleavage of the imidazole moiety.     

Photocatalytic degradation of triazine dyes over N-doped TiO2 in solar radiation

Photocatalytic degradation of the reactive triazine dyes Reactive Yellow 84 (RY 84), Reactive Red 120 (RR 120), and Reactive Blue 160 (RB 160) on anatase phase N-doped TiO₂ in the presence of natural sunlight has been carried out in this work. The effect of experimental parameters like initial pH and concentration of dye solution and dosage of the catalyst on photocatalytic degradation have also been investigated. Adsorption of dyes on N-doped TiO₂ was studied prior to photocatalytic studies. The studies show that the adsorption of dyes on N-doped TiO₂ was high at pH 3 and follows the Langmuir adsorption isotherm. The Langmuir monolayer adsorption capacity of dyes on N-doped TiO₂ was 39.5, 86.0, and 96.3 mg g^?1 for RY 84, RR 120, and RB 160, respectively. The photocatalytic degradation of the dyes follows pseudo first-order kinetics and the rate constant values are higher for N-doped TiO₂ when compared with that of undoped TiO₂. Moreover, the degradation of RY 84 on N-doped TiO₂ in sunlight was faster than the commercial Aeroxide^® P25. However, the P25 has shown higher photocatalytic activity for the other two dyes, RR 120 and RB 160. The COD of 50 mg l^?1 Reactive Yellow-84, RR 120 and RB 160 was reduced by 65.1, 73.1, and 69.6 %, respectively, upon irradiation of sunlight for 3 h in the presence of N-doped TiO₂. The photocatalyst shows low activity for the degradation of RY 84 dye, when its concentration was above 50 mg l^?1, due to the strong absorption of photons in the wavelength range 200–400 nm by the dye solution. LC–MS analysis shows the presence of some triazine compounds and formimidamide derivatives in the dye solutions after 3 h solar light irradiation in the presence of N-doped TiO₂.     

Photocatalytic activity of Au/TiO<Subscript>2</Subscript> nanocomposite for azo-dyes degradation

The structural properties of Au/TiO₂ catalyst were studied by X-ray diffraction, UV-visible diffuse reflectance, photoluminescene, scanning transmission and electron microscope, and temperature programmed reduction. The photocatalytic activity of the catalysts was evaluated for the degradation of various azo-dyes such as methylene blue, methyl orange, reactive blue-4, and eosin-B under solar irradiation. It was found that TiO₂ catalyst modified with gold exhibits higher percentage of degradation compared to starting TiO₂. For example, TiO₂ showed 35% of methyl orange degradation whereas gold modified TiO₂ possessed 82%. Effect of different parameters such as pH and dye concentration has been evaluated and the photocatalytic activity was correlated with physico-chemical properties. The dye degradation rate followed first order kinetics.