Interference of chitosan in glucose analysis by high-performance liquid chromatography with evaporative light scattering detection

The purpose of this work was to quantify glucose in aqueous solutions containing chitosan by high-performance liquid chromatography (HPLC) with evaporative light scattering detection (ELSD). Chitosan is a natural compound that is used alone or as an additive in several formulations. Microencapsulation of bioactive compounds such as glucose, by means of chitosan, is being explored, but difficulties arise when glucose needs to be determined in the presence of chitosan. HPLC is the technique most commonly used for glucose analysis, and ELSD may offer advantages (e.g. sensitivity and the possibility of operating in gradient mode) compared with other detectors. The influence of chitosan in the analysis of glucose by HPLC with ELSD was investigated at different pH values of the aqueous solutions. Isocratic elution with an acetonitrile/water mixture (80:20, v/v) and water washing between runs were the best options to avoid the mucoadhesive properties of chitosan, which are responsible for column degradation and variability of the retention time of glucose. The developed methodology was considered completely adequate for rapid glucose analysis in aqueous solutions with low pH (< 3), in the presence of chitosan.     

Anomalies in evaporative light scattering detection

A two-dimensional (2-D) “heart-cutting” HPLC system was used to fractionate oligostyrenes into the respective diastereoisomers. For samples of known composition, the response of an ultraviolet (UV) absorbance detector followed the anticipated pattern. The response of an evaporative light-scattering (ELSD) detector on the other hand indicated quite different concentrations for the two diastereoisomers, relative to what was anticipated and what was indicated by the UV detector. Whereas approximately the same concentration was indicated by UV, ELSD in some cases indicated no detection of the later eluting isomer. The magnitude of the errors depended on both the molecular weight and the tacticity of the diastereomers. These anomalies appear to be an artifact of power transform functions imbedded within the firmware processor of the ELSD, invisible to the user.     

On the signal response of various pesticides in electrospray and atmospheric pressure chemical ionization depending on the flow-rate of eluent applied in liquid chromatography-tandem mass spectrometry.

The API-MS signal response of several pesticides (atrazine, simazine, isoproturon, diuron, chlorfenvinphos, chlorpyrifos, alachlor, trifluralin) depending on the flow-rate of eluent entering the MS interface was investigated. The investigations were based on API-MS-MS analyses of standard pesticide mixtures in the flow injection mode (FIA) at systematically varied eluent flow-rates using both an ESI interface (Turboionspray) and a heated nebulizer type APCI source. In the result, the individual compounds included in this study showed significant differences in their signal response behaviour depending on the flow-rate of eluent applied. The most hydrophobic compounds among the investigated pesticides (chlorpyrifos and trifluralin) showed drastic losses of sensitivity with increasing eluent flow-rate in both ESI and APCI, while more hydrophilic compounds like atrazine, simazine and isoproturon showed the expected signal response (concentration-sensitive in ESI, mass-flow-sensitive in APCI) at least within a certain range of flow-rates (200-600 microl/min in ESI, 200-2000 microl/min in APCI). These findings lead to the conclusion that application of a programmed HPLC eluent flow-rate may be advantageous to achieve maximum sensitivity of API-MS detection for all pesticides of interest. This is exemplified by the implementation of a flow gradient into an online SPE-HPLC-APCI-MS/MS method for improved analysis of pesticides in drinking water.     

Performance evaluation of evaporative light scattering detection and charged aerosol detection in reversed phase liquid chromatography

In pharmaceutical industry ultraviolet (UV) detection is often used as the preferred detection technique in HPLC analysis since most pharmaceutical compounds possess a UV-absorbing chromophore. However, in case the active pharmaceutical ingredient (API) does not have a UV-absorbing chromophore, or if some of the impurities present lack a chromophore, they will not be detected in routine HPLC analysis employing only a UV detector and alternative detection schemes have to be used. Refractive index detection or mass spectroscopy (MS) can be used but these detectors have their intrinsic weaknesses, such as lack of sensitivity or high cost. With the appearance of semi-universal techniques such as evaporative light scattering detection (ELSD), and more recent, charged aerosol detection (CAD), detection of non-UV-absorbing compounds became feasible without having to resort to such complex or costly detection methods. This paper evaluates the different performance characteristics such as sensitivity, linearity, accuracy and precision of both the ELSD and CAD detector coupled to HPLC. One disadvantage of this type of detector is the non-linear response behaviour which makes direct linear regression for making calibration curves inaccurate.     

Comparison between evaporative light scattering detection and charged aerosol detection for the analysis of saikosaponins

Saikosaponins are triterpene saponins derived from the roots of Bupleurum falcatum L. (Umbelliferae), which has been traditionally used to treat fever, inflammation, liver diseases, and nephritis. It is difficult to analyze saikosaponins using HPLC-UV due to the lack of chromophores. Therefore, evaporative light scattering detection (ELSD) is used as a valuable alternative to UV detection. More recently, a charged aerosol detection (CAD) method has been developed to improve the sensitivity and reproducibility of ELSD. In this study, we compared CAD and ELSD methods in the simultaneous analysis of 10 saikosaponins, including saikosaponins-A, -B₁, -B₂, -B₃, -B₄, -C, -D, -G, -H and -I. A mixture of the 10 saikosaponins was injected into the Ascentis^® Express C18 column (100 mm × 4.6 mm, 2.7 μm) with gradient elution and detection with CAD and ELSD by splitting. We examined various factors that could affect the sensitivity of the detectors including various concentrations of additives, pH and flow rate of the mobile phase, purity of nitrogen gas and the CAD range. The sensitivity was determined based on the signal-to-noise ratio. The best sensitivity for CAD was achieved with 0.1 mM ammonium acetate at pH 4.0 in the mobile phase with a flow rate of 1.0 mL/min, and the CAD range at 100 pA, whereas that for ELSD was achieved with 0.01% acetic acid in the mobile phase with a flow rate at 0.8 mL/min. The purity of the nitrogen gas had only minor effects on the sensitivities of both detectors. Finally, the sensitivity for CAD was two to six times better than that of ELSD. Taken together, these results suggest that CAD provides a more sensitive analysis of the 10 saikosaponins than does ELSD.     

Linearization of evaporative light scattering detector signal

Recent advances in nebulizer technology of the evaporative light scattering detector (ELSD) allow the evaporation of trichlorobenzene (TCB) at much lower temperatures than the previous instruments, thus avoiding the sample loss in the lower molecular weight domain. Therefore, the new ELSD opens the possibility to correctly evaluate the molecular weight distribution (MWD) of polymers by gel permeation chromatography, after linearizing the ELSD signal intensity in function of concentration. To find the correct exponent parameter for linearization, it is necessary to take into account not only the peak area, but each point of the chromatogram. The evaluation method for this exponent parameter, found to be 1.61 for the analysis in TCB of polyolefin and polystyrene samples, is presented in this study. This value was verified by the excellent correlation found between the obtained MWD of a high-density polyethylene both with the ELSD and with the traditional differential refractive index detector.     

Use of evaporative light scattering detector in the detection and quantification of enantiomeric mixtures by HPLC

Routinely used in our laboratories at analytical scale, an evaporative light scattering detector (ELSD) has proved to be versatile in the detection of enantiomeric resolution using chiral stationary phases by HPLC. Though this kind of detector has been widely used in various domains, its application in enantiomeric resolution has not been discussed in the literature and is found to have very specific features especially in the quantitative perspective. In contrast with the UV detection, the peak area from ELSD for both enantiomers of a racemic mixture may not be the same. This complicates the assessment of the enantiomeric purity of unknown samples. This current work deals with some practical aspects in the detection of enantiomers and in accurate quantitative determination of enantiomeric purity by ELSD. Effects of analyte nature (more precisely molecular weight and volatility), peak shape and peak shape difference between enantiomers on the quantitative integration by ELSD are discussed in connection with the UV-detection results. The calibration for quantitative enantiomeric analysis and its effectiveness are demonstrated.     

Improving the universal response of evaporative light scattering detection by mobile phase compensation

Mobile phase compensation, first reported for the charged aerosol detector (CAD), was used as a suitable method to overcome problems related to the mobile phase-dependent response of the evaporative light scattering detector (ELSD). Mobile phase compensation was effectively performed both in the flow injection- and in gradient modes. Without compensation, the response factors of the ELSD for six sulfonamide drugs differed by a factor of two when varying the mobile phase composition between 10 and 90% acetonitrile. This change could be effectively eliminated using the technique of mobile phase compensation, where a secondary pump with a reversed gradient was used to provide the detector with a constant composition of the mobile phase. For identical experimental conditions, the ELSD showed a nearly constant, albeit somewhat reduced, response with compensation. This indicates that under such conditions, the ELSD behaved as a concentration-sensitive detector. The analysis of sulfonamides drugs at 0.05% level using gradient UPLC-ELSD separation with mobile phase compensation is demonstrated.     

Determination of gentamicin sulfate and related compounds by high-performance liquid chromatography with evaporative light scattering detection

A rapid and simple method for the separation and quantitation of gentamicin sulfate by HPLC coupled with evaporative light scattering detection (ELSD) has been developed. Detection of the different components of gentamicin is problematic because of the lack of UV absorbing chromophore. The use of the universal ELSD avoids the need for sample derivatization or use of specific detector such as pulsed amperometry. Separation was performed on a highpurity C18 125 mm x 4 mm i.d., 3 microm, reversed phase column with 48.5 mM trifluoroacetic acid-methanol (97:3, v/v), as mobile phase at a flow rate of 0.7 ml/min. The influence of the gas nature, gas pressure and temperature of the drift tube of the detector on the detection response was investigated. Optimization was performed with the help of a specific experimental design software. This method allows the determination of the composition in components C1, C1a, C2, C2a and C2b of gentamicin sulfate samples. Mass spectrometry was employed to confirm the ELSD chromatographic profile. The method was validated using methodology described by the International Conference of Harmonization in the field of Medicinal Substances. Commercial samples of different sources were analyzed and results were in good agreement with specifications of both European and United States Pharmacopoeia.     

Separation and determination of carbohydrates in drinks by ion chromatography with a self-regenerating suppressor and an evaporative light-scattering detector

Analysis of glucose and other carbohydrates are often performed by use of normal phase HPLC methods with acetonitrile as major eluent coupled with evaporative light-scattering detector (ELSD) or by use of anion-exchange ion chromatography (IC) methods with NaOH as eluent coupled with pulsed amperimetric electrochemical detector. In this work, a novel method for the determination of carbohydrates by IC in conjunction with a self-regenerating suppressor and an ELSD detector was investigated. Three carbohydrates (glucose, fructose, and sucrose) were separated using a KOH eluent generator to avoid the effect of carbon dioxide absorption in the alkaline eluent. Due to the use of the suppressor, non-volatile components were removed and a low salt background (K+ approximately 0.070 microg/mL) can be obtained so the suppressed eluent could directly go into an ELSD detector without obvious interference of inorganic salts. After examining the changes in retention and resolution, an optimized method was established (for IC: using 32 mM KOH as the eluent at a flow rate of 1 mL/min; for ELSD: operated at 95 degrees C, 4.0 bar nitrogen with a gas flow rate of 2.0 L/min) and the linearity, reproducibility, and the limit of detection (LOD) for the three carbohydrates were further evaluated. Regression equations revealed acceptable linearity (correlation coefficients=0.994-0.998) across the working-standard range (100-1000 microg/mL for glucose and sucrose, 150-1000 microg/mL for fructose) and LODs of glucose, fructose, and sucrose were 93, 126, and 90 microg/mL, respectively. This method has successfully been applied to the determination of the three carbohydrates in carbonated cola drinks and fruit juices. The recoveries were between 95 and 113% (n=3) for different carbohydrates.     

Fingerprint analysis of Dioscorea nipponica by high-performance liquid chromatography with evaporative light scattering detection

High-performance liquid chromatographic method (HPLC) with evaporative light scattering detection (ELSD) coupled with microwave-assisted extraction (MAE) as an efficient sample preparation technique has been developed for fingerprint analysis of Dioscorea nipponica. The samples were separated with an Agilent C8 column using water (A) and acetonitrile (B) under gradient conditions (0-10 min, linear gradient 20-40% B; 10-12 min, linear gradient 40-42% B; 12-25 min, isocratic 42% B) as the mobile phase at a flow rate of 1 mL min⁻¹ within 22 min. The ELSD conditions were optimized at nebulizer-gas flow rate 2.7 L min⁻¹ and drift tube temperature 90 °C. Precision experiments showed relative standard deviation (R.S.D.) of peak area and retention time were better than 2.5%; inter-day and intra-day variabilities showed that R.S.D. was ranged from 0.78% to 4.74%. Limit of detection was less than 50 μg mL⁻¹ and limit of quantification was less than 80 μg mL⁻¹. Accuracy validation showed that average recovery was between 97.39% and 104.07%. The method was validated to achieve the satisfactory precision and recovery. Relative retention time and relative peak area were used to identify the common peaks for fingerprint analysis. There are nine common peaks in the fingerprint. The quality of seven batches of D. nipponica samples was evaluated to be qualified or unqualified by the parameters “difference” and “total difference” of common peaks. Furthermore, the contents of important medicinal compounds (dioscin, prodioscin and gracillin) in different batches of D. nipponica samples were determined simultaneously using the developed HPLC-ELSD method. The results indicated variation of the herb quality which might be related to different producing area, growing condition, climate, harvest time, drug processing and so on. The developed analytical procedure was proved to be a reliable and rapid method for the quality control of D. nipponica.     

Simultaneous separation of nine surfactants of various types by HPLC with evaporative light scattering detection

A simultaneous separation of cationic, amphoteric and nonioinc nine surfactants (DMDS, DMDP, DMDM, DMDL, BZC, CDE, A/O, SUNC, IMD) has been performed by a reverse phase-HPLC method utilizing a single J'sphere ODS (250 mm × 4.6 mm, 4 μm) column and a methanol-water containing 0.2% TFA eluent system within 60 min. The observed precision in determination of concentration was less than 5% R.S.D., which revealed that ELSD was an effective tool to detect the various studied surfactants of low volatility without chromophore. In addition, the detection limits were in the concentration range of 3.5-10 μg/mL, and the calibration curves, i.e. the log-log plots, were linear in the working range of 5-4600 μg/mL with the slopes of 1.321-1.668. The application of the analytical procedure to three household products without pretreatment supported that the presented chromatographic method was simple to be practical for a routine analysis of commercial products.     

Polyketide analysis using mass spectrometry,evaporative light scattering,and charged aerosol detector systems

In this study, a mass spectrometer (MS), an evaporative light scattering detector (ELSD), and a charged aerosol detector (CAD) were used to analyze an erythromycin precursor (termed 6-deoxyerythronolide B). The work highlights the capabilities of each detector to analyze a representative polyketide compound that does not possess a natural chromophore, and presents the first comparison to include a charged aerosol system. Each detector was evaluated based upon limit of detection (LOD), dynamic range, and precision in the context of polyketide analysis. Due to its low LOD, wide dynamic range, and ability to provide molecular weight information, the MS was deemed the best detection option for the analysis of low-concentration, poorly identified polyketide compounds. Alternatively, both the CAD and ELSD systems studied showed better precision and accuracy. The ELSD demonstrated the best precision at 3%, but its LOD was limited to concentrations primarily greater than or equal to 1 mg/L. The Corona CAD demonstrated a LOD (0.012 mg/L) and dynamic range comparable to mass spectroscopy and therefore serves as a more cost-efficient alternative for polyketide production schemes with low titers.     

Postcolumn fluorescence as an alternative to evaporative light scattering detection for ceramide analysis with gradient elution in non-aqueous reversed-phase liquid chromatography

Ceramide analysis was developed with gradient elution in non-aqueous reversed-phase liquid chromatography with evaporative light scattering detection (ELSD) or postcolumn fluorescence detection. Fluorescence detection (excitation, 360 nm; emission, 425 nm) after postcolumn formation of mixed assemblies between eluted ceramides and 1,6-diphenyl-1,3,5-hexatriene was developed. In comparison with ELSD, fluorescence detection allows a better detection of the minor species ceramide from ceramide type III (commercial mixture of non-hydroxy fatty acid-sphingosine) and appears to be more sensitive for quantitation of ceramides at low concentrations. The fluorescence response is linear over a wide range of injected amount of ceramide III (expressed as stearoyl-phytosphingosine): 10 ng to 1000 ng. The response of ELSD is non linear but can be linearized in double logarithmic coordinates for calculations over a narrow range, e.g. between 10 to 350 ng ceramide III injected. The lower quantitation limits of these two detectors are similar: 5 ng ceramide III was injected.     

Application of a xenon arc lamp as a light source for evaporative light scattering detection

The standard tungsten-halogen light source used in a commercial evaporative light scattering detector (ELSD) was replaced with a 180 W xenon arc lamp. The xenon arc lamp possesses a broader spectrum in the UV region than the halogen source. The influence of the UV transmittance of five selected solvents was studied with a size-exclusion chromatography column. This solvent parameter was not observed to influence the ELSD response between the two light source settings. With the solvents studied, better sensitivity was obtained with the xenon arc lamp than the halogen lamp. This high-energy source was applied to ceramide III analysis with an octadecyl-grafted silica column and methanol:tetrahydrofuran 97:3 as the mobile phase, and the sensitivity of the quantification of ceramide III increased 16-fold for injected amounts of 14∼140 ng. The molecular species in a sample of naturally occurring ceramides was analyzed using two C18 columns at 40 °C and gradient elution from 100% acetonitrile to 100% isopropanol in 30 min. The increased ELSD sensitivity achieved when using the xenon arc lamp allowed both the minor and major ceramide species to be observed, in contrast to the results achieved when the halogen lamp was used, where the increased photomultiplier voltage needed to observed the signals from the minor species caused the signals from the major ceramide species to occur above the detector response window.     

Proposed performance qualification and calibration method for evaporative light scattering detectors

Summary A method for the performance testing of Sedex 55 Evaporative Light Scattering Detectors (ELSD) has been developed as part of our regulatory compliance programme. The method uses a readily available chromatographic column, caffeine as the test probe and can be completed in less than one hour.     

Simultaneous determination of major bioactive components in Qingkailing injection by high-performance liquid chromatography with evaporative light scattering detection

High-performance liquid chromatography with evaporative light scattering detection (HPLC/ELSD) was established for simultaneous determination of seven major bioactive components of Qingkailing injection including adenosine, geniposide, chlorogenic acid, baicalin, ursodeoxycholic acid, cholic acid, and hyodeoxycholic acid. The proposed method was applied to analyze ten various Qingkailing injections and produced data with acceptable linearity, repeatability, precision and accuracy having a limit of detection (LOD) of 10-50 ng. In comparison with UV detection, HPLC/ELSD permits the determination of non-chromophoric compounds without prior derivatization, and shows good compatibility to the multi-components of complex analytes. The proposed method is a useful alternative for routine analysis in the quality control of traditional Chinese medicine.     

Simultaneous determination of sugars and picrosides in Picrorhiza species using ultrasonic extraction and high-performance liquid chromatography with evaporative light scattering detection

Sugars play a critical role in regulating overall cellular metabolism in high altitude growing plants. These plants are shown to have high levels of sugars to enhance their tolerance to abiotic stresses such as drought and freezing temperature. In the present study, a simple, sensitive, selective and reliable HPLC method based on ultrasonic extraction and evaporative light scattering detection (ELSD) has been developed and validated for the simultaneous determination of important sugars (xylose, xylitol, mannitol, glucose and sucrose) and picrosides (picroside-I and picroside-II) in two species Picrorhiza kurroa and P. scrophulariiflora. The analysis was carried out on a Zorbax amino column (250 mm x 4.6 mm i.d., 5 microm) with isocratic elution of acetonitrile:water (78:22, v/v). The method was validated for accuracy, precision, limit of detection and quantification according to International Conference on Harmonization (ICH) guidelines. The drift tube temperature of the ELSD system was set to 81 degrees C and nitrogen flow rate was 2.0 standard liter per minute (SLM). The regression equation revealed a good linear relationship (r(2)=0.9997+/-0.0012) within test ranges. The limit of detection and quantification for seven analytes in ELSD were less than 0.98 and 2.95 microg, respectively. The method showed good reproducibility for the quantification of seven analytes in Picrorhiza species with intra- and inter-day variation of less than 2.0%.     

Determination of inorganic cations in brine solutions by ion chromatography

The method for analysis of inorganic cations in brine solutions was developed. Ion chromatography is a well-established and accepted technique in the determination of a variety of inorganic ions. However, there are significant complications when ion chromatography is used to determine trace concentrations of inorganic ions in brine matrices. The brine solution in our study was made to simulate the solution from the Waste Isolation Pilot Plant. Instrumental parameters such as eluent composition, flow-rates, and sample loop volumes were investigated to arrive at the optimum condition for the determination of the cations with minimal dilution. Separation was carried out in a Dionex CG12A/CS12A with 8.25 mM H2SO4 as eluent at 1.2 ml/min flow-rate. Our results indicated that ion chromatography is an accurate and a good alternative method for the analysis of cations in brine solution.     

Analytical and biological evaluation of high throughput screen actives using evaporative light scattering, chemiluminescent nitrogen detection, and accurate mass LC-MS-MS

In this investigation the utility of evaporative light scattering detection (ELSD) combined with HPLC-MS was demonstrated as a key component of a bioassay-guided fractionation, or "biofractionation" technique, for the evaluation of high throughput screen actives. ELSD provided on-line analyte mass information that was critical for the classification of the samples. Chemiluminescent nitrogen detection (CLND) was also evaluated for sample concentration estimation for nitrogen-containing compounds, and accurate mass LC-MS-MS analysis was employed for rapid structural confirmation and elucidation of components previously identified as active via biofractionation.