Characterization of grafting density and binding efficiency of DNA and proteins on gold surfaces

The surface grafting density of biomolecules is an important factor for quantitative assays using a wide range of biological sensors. We use a fluorescent measurement technique to characterize the immobilization density of thiolated probe DNA on gold and hybridization efficiency of target DNA as a function of oligonucleotide length and salt concentration. The results indicate the dominance of osmotic and hydration forces in different regimes of salt concentration, which was used to validate previous simulations and to optimize the performance of surface-stress based microcantilever biosensors. The difference in hybridization density between complementary and mismatched target sequences was also measured to understand the response of these sensors in base-pair mismatch detection experiments. Finally, two different techniques for immobilizing proteins on gold were considered and the surface densities obtained in both cases were compared.     

Nanomechanics of the formation of DNA self-assembled monolayers and hybridization on microcantilevers

Biomolecular interactions over the surface of a microcantilever can produce its bending motion via changes of the surface stress, which is referred to nanomechanical response. Here, we have studied the interaction forces responsible for the bending motion during the formation of a self-assembled monolayer of thiolated 27-mer single-stranded DNA on the gold-coated side of a microcantilever and during the subsequent hybridization with the complementary nucleic acid. The immobilization of the single-stranded DNA probe gives a mean surface stress of 25 mN/m and a mean bending of 23 nm for microcantilevers with a length and thickness of about 200 microm and 0.8 microm, respectively. The hybridization with the complementary sequence could not be inferred from the nanomechanical response. The nanomechanical response was compared with data from well-established techniques such as surface plasmon resonance and radiolabeling, to determine the surface coverage and study the intermolecular forces between neighboring DNA molecules anchored to the microcantilever surface. From both techniques, an immobilization surface density of 3 x 10(12) molecules/cm(2) and a hybridization efficiency of 40% were determined. More importantly, label-free hybridization was clearly detected in the same conditions with a conventional sensor based on surface plasmon resonance. The results imply that the nanomechanical signal during the immobilization process arises mainly from the covalent attachment to the gold surface, and the interchain interactions between neighboring DNA molecules are weak, producing an undetectable surface stress. We conclude that detection of nucleic acid hybridization with nanomechanical sensors requires reference cantilevers to remove nonspecific signals, more sensitive microcantilever geometries, and immobilization chemistries specially addressed to enhance the surface stress variations.     

用于DNA杂交检测的丝网印刷型生物传感器的研究

将单链DNA(ssDNA)固定到丝网印刷碳电极上构成电化学DNA传感器,采用电化学指示剂,建立DNA杂交的检测方法.Co(phen)33+电化学指示剂通过钴盐与配体邻菲罗啉络合制备,采用等离子发射光谱法(ICP-AES)和核磁共振法(NMR)表征功能基团,采用循环伏安法(CV)分析指示剂的电化学特性,并以此为基础研究ssDNA在电极表面的固定及DNA杂交过程.本研究探讨了直接吸附、静电吸附与键合等3种ssD-NA在电极表面的固定方法,结果表明,静电吸附法和键合法具有较高的ssDNA固定量,采用静电吸附法固定探针的电极杂交目标DNA后,Co(phen)33+易于嵌入双链DNA (dsDNA)中,CV峰电流(ip)信号随目标DNA浓度增加.本研究采用静电吸附ssDNA的电极检测DNA杂交,实验表明,当探针固定液中ssDNA浓度为5 mg/L时,目标DNA浓度在6.65×10- 8～4.26× 10-6mol/L范围内,Co(phen)33+在dsDNA修饰电极上ip值与DNA浓度呈良好的线性关系,R2为0.9819.本研究为建立新的微生物分子分型手段提供了初步依据.     

Chemical Characterization of DNA-Immobilized InAs Surfaces Using X-ray Photoelectron Spectroscopy and Near-Edge X-ray Absorption Fine Structure

Single-stranded DNA immobilized on an III-V semiconductor is a potential high-sensitivity biosensor. The chemical and electronic changes occurring upon the binding of DNA to the InAs surface are essential to understanding the DNA-immobilization mechanism. In this work, the chemical properties of DNA-immobilized InAs surfaces were determined through high-resolution X-ray photoelectron spectroscopy (XPS) and near-edge X-ray absorption fine structure (NEXAFS). Prior to DNA functionalization, HF- and NH(4)OH- based aqueous etches were used to remove the native oxide from the InAs surface. The initial chemical state of the surface resulting from these etches were characterized prior to functionalization. F-tagged thiolated single-stranded DNA (ssDNA) was used as the probe species under two different functionalization methods. The presence of DNA immobilized on the surface was confirmed from the F 1s, N 1s, and P 2p peaks in the XPS spectra. The presence of salt had a profound effect on the density of immobilized DNA on the InAs surface. To study the interfacial chemistry, the surface was treated with thiolated ssDNA with and without the mercaptohexanol molecule. An analysis of the As 3d and In 3d spectra indicates that both In-S and As-S are present on the surface after DNA functionalization. The amount of In-S and As-S was determined by the functionalization method as well as the presence of mercaptohexanol during functionalization. The orientation of the adsorbed ssDNA is determined by polarization-dependent NEXAFS utilizing the N K-edge. The immobilized ssDNA molecule has a preferred tilt angle with respect to the substrate normal, but with a random azimuthal distribution.     

水溶性碳纳米粒子的制备及其在DNA和单核苷酸多态性分析中的应用

利用电化学氧化的方法制备了水溶性好、粒径为7～12nm的碳纳米粒子,该碳纳米粒子通过π-π相互作用吸附荧光标记的单链DNA探针,并能有效地猝灭其荧光．当单链DNA探针与匹配的DNA目标分子杂交形成双链DNA时,猝灭的荧光被恢复,由此可以检测1-200nmol／L的DNA目标分子。此外,在碳纳米粒子存在时,由荧光标记的DNA探针和DNA目标分子形成的双链DNA的熔解温度可以简便地被测定,当双链DNA有错配碱基时,其熔解温度降低,由此可方便、快速地分析单核苷酸多态性．     

Lable‐Free Electrochemical DNA Sensor Based on Gold Nanoparticles/Poly(neutral red) Modified Electrode

We present a new strategy for the label‐free electrochemical detection of DNA hybridization based on gold nanoparticles (AuNPs)/poly(neutral red) (PNR) modified electrode. Probe oligonucledotides with thiol groups at the 5‐end were covalently linked onto the surface of AuNPs/PNR modified electrode via S‐Au binding. The hybridization event was monitored by using differential pulse voltammetry (DPV) upon hybridization generates electrochemical changes at the PNR‐solution interface. A significant decrease in the peak current was observed upon hybridization of probe with complementary target ssDNA, whereas no obvious change was observed with noncomplementary target ssDNA. And the DNA sensor also showed a high selectivity for detecting one‐mismatched and three‐mismatched target ssDNA and a high sensitivity for detecting complementary target ssDNA, the detection limit is 4.2×10^?12 M for complementary target ssDNA. In addition, the DNA biosensor showed an excellent reproducibility and stability under the DNA‐hybridization conditions.     

Single probe nucleic acid immobilization on chemically modified single protein by controlling ionic strength and pH

In an effort toward determining the feasibility of single molecule analysis, we describe a case whereby the binding of one biotinylated DNA to one streptavidin molecule via electrostatic interactions was controlled by altering in pH 4.0-9.0 and 0.16 of the ion strength. The quantitative analysis of immobilized probe ssDNA was realized in real-time via a quartz crystal microbalance (QCM) and electrochemical (EC) measurement in the range 100 pM to 50 μM of probe oligonucleotide concentration. The variation amount of biotinylated ssDNA immobilized on the streptavidin-modified surface at pH 7.5 was about 0.16 pmol, giving a ratio of streptavidin to biotinylated ssDNA of about 1:1.1. On the other hand, at pH 4.9, it was immobilized about 0.29 pmol. From the shape of the Langmuir plot and QCM, the immobilization efficiency of biotinylated DNA via streptavidin at pH 4.9 was approximately twofold that at pH 7.5. In view points of the reaction velocity, it was increased with decreasing buffer solution pH, indicating a strong interaction of negatively charged probe DNA with the positively charged streptavidin. And also the EC response value of ΔI/I_streptavidin for the immobilized biotinylated ssDNA in pH 4.9 was about 49%, while the corresponding value for the pH 7.5 was approximately 34%. As DNA molecules possess negative charges, electrostatic repulsion occurred between streptavidin and biotinylated ssDNA at pH 7.5. At pH 4.9, the attraction between the biotinylated ssDNA and streptavidin resulted in increased adsorption which has an isoelectric point of about 5.9. It was deduced that the binding of biotinylated ssDNA to one or two of the four binding sites of streptavidin can be controlled by adjusting the pH-controlled electrostatic interaction.     

DNA hybridization-induced reorientation of liquid crystal anchoring at the nematic liquid crystal/aqueous interface

Interactions between DNA and an adsorbed cationic surfactant at the nematic liquid crystal (LC)/aqueous interface were investigated using polarized and fluorescence microscopy. The adsorption of octadecyltrimethylammonium bromide (OTAB) surfactant to the LC/aqueous interface resulted in homeotropic (untilted) LC alignment. Subsequent adsorption of single-stranded DNA (ssDNA) to the surfactant-laden interface modified the interfacial structure, resulting in a reorientation of the LC from homeotropic alignment to an intermediate tilt angle. Exposure of the ssDNA/OTAB interfacial complex to its ssDNA complement induced a second change in the interfacial structure characterized by the nucleation, growth, and coalescence of lateral regions that induced homeotropic LC alignment. Fluorescence microscopy showed explicitly that the complement was colocalized in the same regions as the homeotropic domains. Exposure to noncomplementary ssDNA caused no such response, suggesting that the homeotropic regions were due to DNA hybridization. This hybridization occurred in the vicinity of the interface despite the fact that the conditions in bulk solution were such that hybridization did not occur (high stringency), suggesting that the presence of the cationic surfactant neutralized electrostatic repulsion and allowed for hydrogen bonding between DNA complements. This system has potential for label-less and portable DNA detection. Indeed, LC response to ssDNA target was detected with a lower limit of approximately 50 fmol of complement and was sufficiently selective to differentiate a one-base-pair mismatch in a 16-mer target.     

Impedance‐Based DNA Biosensor Employing Molecular Beacon DNA as Probe and Thionine as Charge Neutralizer

In this paper, we present an impedance‐based DNA biosensor using thionine intercalation to amplify DNA hybridization signal. Beacon single‐stranded DNA (ssDNA) probe and mercaptoacetic acid were self‐assembled onto a Au electrode by forming Au? S bonds. These beacon ssDNAs were hybridized with the complementary sequences around the loop structure. Then thionine was intercalated into the double‐stranded DNA (dsDNA) immobilized on the Au electrode surface. Due to the neutralization of the negative charges of dsDNA by the intercalated thionine, the electronic transfer resistance (R_et) of the DNA modified Au electrode was significantly diminished. Herein, the decreased value of R_et resulted from the thionine intercalating into dsDNA was employed as the hybridization signal. SDS was used to reduce the unspecific adsorption between ssDNA and thionine. Several experimental conditions, including the surface coverage of ssDNA probe on Au electrode, the hybridization temperature and time were all optimized. Moreover, the hybridization reactions of the unstructured linear ssDNA probe and the structured beacon ssDNA probe with their complementary sequences were compared in this work. The sensitivity of the presented DNA biosensor highlighted that the intercalation of thionine into dsDNA was an efficient approach to amplify the hybridization signal using impedance detection technique. Additionally, in this DNA biosensing protocol, beacon ssDNA has a good ability to distinguish target DNA sequences. This results in a higher specificity than using traditional unstructured DNA probe.     

A simple visual method for DNA detection based on the formation of gold nanoparticles

A simple visual method for DNA detection during the formation of gold nanoparticles (AuNPs) was developed based on different electrostatic properties of single strand DNA (ssDNA) and double strand DNA (dsDNA). It could identify target DNA in 10 min.     

Characterization of single- and double-stranded DNA on gold surfaces

Single- and double-stranded deoxy ribonucleic acid (DNA) molecules attached to self-assembled monolayers (SAMs) on gold surfaces were characterized by a number of optical and electronic spectroscopic techniques. The DNA-modified gold surfaces were prepared through the self-assembly of 6-mercapto-1-hexanol and 5'-C(6)H(12)SH -modified single-stranded DNA (ssDNA). Upon hybridization of the surface-bound probe ssDNA with its complimentary target, formation of double-stranded DNA (dsDNA) on the gold surface is observed and in a competing process, probe ssDNA is desorbed from the gold surface. The competition between hybridization of ssDNA with its complimentary target and ssDNA probe desorption from the gold surface has been investigated in this paper using X-ray photoelectron spectroscopy, chronocoulometry, fluorescence, and polarization modulation-infrared reflection absorption spectroscopy (PM-IRRAS). The formation of dsDNA on the surface was identified by PM-IRRAS by a dsDNA IR signature at approximately 1678 cm(-)(1) that was confirmed by density functional theory calculations of the nucleotides and the nucleotides' base pairs. The presence of dsDNA through the specific DNA hybridization was additionally confirmed by atomic force microscopy through colloidal gold nanoparticle labeling of the target ssDNA. Using these methods, strand loss was observed even for DNA hybridization performed at 25 degrees C for the DNA monolayers studied here consisting of attachment to the gold surfaces by single Au-S bonds. This finding has significant consequence for the application of SAM technology in the detection of oligonucleotide hybridization on gold surfaces.     

A simple visual method for DNA detection based on the formation of gold nanoparticles

A simple visual method for DNA detection during the formation of gold nanoparticles (AuNPs) was developed based on different electrostatic properties of single strand DNA (ssDNA) and double strand DNA (dsDNA). Since the ssDNA is easy to bind to AuNPs due to its exposed bases which could prevent salt-induced aggregation of AuNPs. The dsDNA always present negative charge because its negatively charged phosphate backbone is exposed. In this case, the dsDNA could disturb the adsorption between dsDNA and AuNPs and result in non-aggregation of AuNPs. After hybridization, chloroauric acid and ascorbic acid were added to the mixture solution, and the solution changed to red immediately and turned to purple in 10 min in the present of target DNA. TEM results confirmed that the change of color stemed from aggregation of AuNPs. In order to obtain accurate results by naked eye, the DNA detection assay should be conducted under pH 7.0.     

Controlling DNA orientation on mixed ssDNA/OEG SAMs

We present and characterize a mixed self-assembled monolayer (SAM) consisting of single-stranded oligonucleotide (ssDNA)- and oligo(ethylene glycol) (OEG)-terminated thiols. The ssDNA/OEG SAMs are prepared by simultaneous coadsorption from a common thiol solution over a broad range of compositions. Electron spectroscopy for chemical analysis (ESCA) is used to measure the surface coverage of ssDNA, whereas surface plasmon resonance (SPR) sensor is used to measure the hybridization of complementary ssDNA and protein resistance. Through the complementary use of these techniques, we find that the composition of OEG in the assembly solution controls a key parameter: the surface coverage of ssDNA on the surface. There is evidence that it influences the orientation of the immobilized ssDNA probes. Lower OEG concentrations yield a surface with higher ssDNA coverage and less favorable orientation, whereas higher OEG concentrations produce a surface with lower DNA coverage and more favorable orientation. Competition between these two effects controls the hybridization efficiency of the ssDNA surface. Compared to ssDNA surfaces prepared with other diluent thiols, the use of OEG improves the protein resistance of the surface, making it more broadly applicable.     

Chemomechanics of surface stresses induced by DNA hybridization

When biomolecular reactions occur on one surface of a microcantilever beam, changes in intermolecular forces create surface stresses that bend the cantilever. While this phenomenon has been exploited to create label-free biosensors and biomolecular actuators, the mechanisms through which chemical free energy is transduced to mechanical work in such hybrid systems are not fully understood. To gain insight into these mechanisms, we use DNA hybridization as a model reaction system. We first show that the surface grafting density of single-stranded probe DNA (sspDNA) on a surface is strongly correlated to its radius of gyration in solution, which in turn depends on its persistence length and the DNA chain length. Since the persistence length depends on ionic strength, the grafting density of sspDNA can be controlled by changing a solution's ionic strength. The surface stresses produced by the reaction of complementary single-stranded target DNA (sstDNA) to sspDNA depend on the length of DNA, the grafting density, and the hybridization efficiency. We, however, observe a remarkable trend: regardless of the length and grafting density of sspDNA, the surface stress follows an exponential scaling relation with the density of hybridized sspDNA.     

Towards the optimization of an optical DNA sensor: control of selectivity coefficients and relative surface affinities

Short single-stranded DNA (ssDNA) oligonucleotides can be grown on the surface of fused silica by automated nucleic acid synthesis. The immobilized ssDNA can be deposited at a desired average density. The density of ssDNA provides a controlled parameter that in combination with temperature, ionic strength and pH, can be used to define the selectivity of hybridization. Furthermore, the density of ssDNA can be used to control the affinity of complementary DNA so that it associates with the nucleic acids on the surface rather than areas that are not coated with ssDNA. The characteristic melt temperature observed for immobilized double-stranded DNA (dsDNA) 20mer shifts by up to 10 °C when a single base pair mismatch is present in the center of a target oligonucleotide. Optimization of quantitative analysis of such single base pair mismatches requires use of select experimental conditions to maximize the formation of the fully matched target duplex while minimizing the formation of the mismatched duplex. Results based on fiber optic biosensors that are used to study binding of fluorescein-labeled complementary DNA demonstrate that it is possible to achieve a selectivity coefficient of fully matched to single base pair mismatch of approximately 85-1, while maintaining >55% of the maximum possible signal that can be obtained from the fully matched target duplex.     

A DNA biosensor based on resonance light scattering using unmodified gold bipyramids

We report on a novel biosensor for determining sequence-specific DNA. It is based on resonance light scattering (RLS) caused by the aggregation of gold bipyramids. These display localized surface plasmon resonance and can be used as a bioprobe. The absorption spectra and the transmission electron micrographs provide visual evidence of the aggregation of the gold bipyramids in the presence of DNA. The RLS intensity of the gold bipyramids increases with the concentration of the target DNA. The method was successfully applied to the determination of a 30-mer single-stranded oligonucleotide and works over the 0.1–10?nM concentration range.

Detection of bar gene encoding phosphinothricin herbicide resistance in plants by electrochemical biosensor

An electrochemical biosensor for the detection of bar gene coding phosphinothricin herbicide resistance is presented. The detection was based on hybridization reaction between the specific to bar gene 19-mer probe immobilized on the electrode surface and complementary DNA in a sample. Single-stranded DNA probe specific to bar gene was covalently attached by 5'-phosphate end to the surface of carbon paste electrode. Outer layer of a conventional CPE was provided with carboxyl groups of stearic acid. ssDNA was coupled to the electrode through ethylenediamine with the use of water-soluble 1-ethyl-3(3'-dimethylaminopropyl)-carbodiimide and N-hydroxy-sulfosuccinimide as activating reagents. Hybridization reaction at the electrode surface was detected via Co(bpy)(3)(3+), which possess a much higher affinity to the resulting DNA duplex compared to ssDNA probe. Detection limit of the sensor was 0.1 microM of target DNA fragments and its response was linear from 5 to 20 microM. Hybridization event was also detected by measuring guanine peak but this approach presented distinctly higher detection limit (1 muM) and lower reproducibility. Complete time of one measurement with the use of the biosensor including covalent attachment of ethylenediamine (linker) and ssDNA probe to the electrode, hybridization with target and interaction with electroactive indicator was about 70 min.     

Electrochemical DNA Biosensor Based on Partially Reduced Graphene Oxide Modified Carbon Ionic Liquid Electrode for the Detection of Transgenic Soybean A2704‐12 Gene Sequence

In this work a partially reduced graphene oxide (p‐RGO) modified carbon ionic liquid electrode (CILE) was prepared as the platform to fabricate an electrochemical DNA sensor, which was used for the sensitive detection of target ssDNA sequence related to transgenic soybean A2704‐12 sequence. The CILE was fabricated by using 1‐butylpyridinium hexafluorophosphate as the binder and then p‐RGO was deposited on the surface of CILE by controlling the electroreduction conditions. NH₂ modified ssDNA probe sequences were immobilized on the electrode surface via covalent bonds between the unreduced oxygen groups on the p‐RGO surface and the amine group at the 5′‐end of ssDNA, which was denoted as ssDNA/p‐RGO/CILE and further used to hybridize with the target ssDNA sequence. Methylene blue (MB) was used as electrochemical indicator to monitor the DNA hybridization. The reduction peak current of MB after hybridization was proportional to the concentration of target A2704‐12 ssDNA sequences in the range from 1.0×10^?12 to 1.0×10^?6 mol/L with a detection limit of 2.9×10^?13 mol/L (3σ). The electrochemical DNA biosensor was further used for the detection of PCR products of transgenic soybean with satisfactory results.     

Gold nanoparticle-based homogeneous fluorescent aptasensor for multiplex detection

We developed a homogeneous fluorescence assay for multiplex detection based on the target induced conformational change of DNA aptamers. DNA aptamers were immobilized on quantum dots (QDs), and QDs conjugated ssDNA was adsorbed on the surface of gold nanoparticles (AuNPs) by electrostatic interaction between uncoiled ssDNA and the AuNPs. Subsequently the fluorescence of QDs was effectively quenched by the AuNPs due to fluorescence resonance energy transfer (FRET) of QDs to AuNPs. In the presence of targets, the QDs conjugated aptamers were detached from AuNPs by target induced conformational change of aptamers, consequently the fluorescence of the QDs was recovered proportional to the target concentration. In this study, three different QD/aptamer conjugates were used for multiplex detection of mercury ions, adenosine and potassium ions. In a control experiment, all of the three targets were simultaneously detected with high selectivity.     

Spectroscopic Electrochemical Studies of Interaction Between Fuchsin Basic DNA

Visible spectroscopic and electrochemical methods were used to study the interactions between DNA and fuchsin basic(FB). FB has an irreversible electro-oxidation peak in 5 mmol/L Tris-HCl buffer solution at pH = 7.4 on a glassy carbon electrode(GCE). After adding certain concentration of dsDNA, the oxidation peak current of FB decreases, but the peak potential hardly changs. The visible absorption spectroscopic study shows that the binding mode of FB to dsDNA is intercalative binding and electrostatic binding when the ratio of the concentration of dsDNA to FB is smaller than 0. 2, and a new substance, which produces a new absorption peak, is obtained via a covalent binding between dsDNA and FB apart from intercalative binding and electrostatic binding when the ratio of the concentration of dsDNA to FB is larger than 0. 2. The visible absorption spectra varies no longer when the ratio of the concentration of dsDNA to FB is larger than 1.5. A mean binding ratio of dsDNA to FB was determined to be 1.4: 1,suggesting that two complexes FB-dsDNA and FB-2dsDNA be formed. The interaction between FB and ssDNA was only electrostatic binding. The more powerful interaction of FB with dsDNA than with ssDNA may be applied for the recognition of dsDNA and ssDNA, and in DNA biosensor as hybridization indicator.