镍基催化剂上糠醛选择性加氢合成糠醇

采用浸渍法制备了一系列负载的Ni催化剂,用于糠醛选择性加氢反应.用XRD、TPR等手段对Ni/γ-Al2O3样品进行了表征.结果表明,Ni负载量在5~|15%范围内,高度分散于载体γ-Al2O3表面,Ni负载量进一步提高到20%,则在载体表面聚集成为微晶.在10%Ni/γ-Al2O3样品上提高焙烧温度有利于Ni的前驱体分解且高度分散于载体表面.Ni2 与γ-Al2O3存在较强的相互作用,但这种相互作用随着Ni负载量的增加而逐渐减弱,随着焙烧温度的增加而逐渐增强.与其他载体负载的Ni催化剂相比,Ni/γ-Al2O3由于其大的表面和适当的表面结构,在糠醛加氢反应中表现出一定的活性和较高的选择性,且随着Ni负载量的增加,活性逐渐增强,但选择性有所下降.另外催化剂的焙烧温度、还原温度,反应温度和溶剂对该反应均有较大影响,采用极性有机溶剂,适宜的焙烧和还原温度有利于催化剂活性和选择性的提高.     

溶胶-凝胶法制备Ni-SiO2催化剂的表征与性能

以正硅酸乙酯和硝酸镍为原料,采用溶胶-凝胶法,将硝酸镍分别溶于水和乙醇制得凝胶,分别经超临界干燥和常规干燥制备了一系列Ni-SiO2气凝胶和干凝胶催化剂,运用BET、XRD、TPR、IR、H2-TPD和活性评价等方法对催化剂的物理化学性质和催化间二硝基苯加氢性能进行研究.结果表明,Ni-SiO2气凝胶催化剂均具有较高的比表面积,但由于金属镍烧结导致活性比表面积较小,加氢性能较差;以乙醇为溶剂制备的干凝胶催化剂的镍物种分散度较高,但镍与载体之间的相互作用过强,致使催化剂的还原度降低,活性组分利用率下降;以水为溶剂制备的干凝胶催化剂具有较高的活性比表面积,表现出很高的催化活性和选择性.     

新型Ni/TiO_2催化剂用于对硝基苯酚催化加氢

以介孔氧化钛晶须为载体,采用等体积浸渍法制备了Ni/TiO2催化剂,通过扫描电镜、X射线衍射、N2吸附脱附、热重分析和程序升温还原技术对催化剂及其前驱体进行了表征,考察了催化剂中Ni含量及焙烧和还原温度对催化剂催化对硝基苯酚加氢反应性能的影响.结果表明,Ni/TiO2催化剂不仅具有晶须状形貌和高结晶度的锐钛晶型,还保持了高比表面积和介孔结构.随着Ni/TiO2催化剂中镍负载量的增加,对硝基苯酚转化率逐渐增加,当镍负载量超过10%时,催化剂活性和选择性没有明显变化.当镍负载量为10%,焙烧和还原温度分别为500和450 ℃时,Ni/TiO2催化剂的加氢活性最佳,是Raney Ni的4倍.该催化剂循环使用7次后未发现明显失活.     

镍盐前驱体对Ni/C催化剂乙醇气相羰化活性的影响

采用等体积浸渍法制备了分别以乙酰丙酮镍、氯化镍、硝酸镍和醋酸镍为前驱体负载在活性炭上的四种催化剂。用BET、金属分散度、H2-TPR、CO-TPD和XRD等方法研究了四种催化剂的结构特点和乙醇气相羰化活性。结果表明,以醋酸镍制备的Ni/C催化剂的羰化活性最高,乙醇转化率和丙酸选择性分别为96.1%和95.7%,而以乙酰丙酮镍制备的Ni/C催化剂的羰化活性最低,乙醇转化率和丙酸选择性分别为68.9%和27.1%。这种活性的差异与镍盐前驱体和活性炭之间的相互作用强弱有着密切关系。醋酸镍组分与活性炭之间的相互作用较强,浸渍组分易在活性炭表面充分吸附,活性中心Ni0在240－340 ℃温度范围内对CO吸附量最大,还原后金属镍的分散度较好且晶粒较小。     

蒸氨法制备Ni/SiO_2催化剂及其在2-MF加氢制2-MTHF反应中的应用

以硝酸镍为镍源,碱性硅溶胶为硅源,采用蒸氨法制备了Ni/SiO_2催化剂。通过XRD、N_2等温吸附脱附、H_2-TPR、NH_3-TPD、XPS和TG对催化剂进行表征。采用固定床反应器,考察了催化剂焙烧温度及反应条件对催化剂应用于2-甲基呋喃(2-MF)气相加氢合成2-甲基四氢呋喃(2-MTHF)的反应性能。结果表明,蒸氨法制备的Ni/SiO_2催化剂在焙烧后均呈现层状硅酸镍结构,还原后保持了该结构,活性组分Ni晶粒尺寸较小、金属载体相互作用较强,从而具有较高的活性。催化剂的焙烧温度影响催化剂Ni晶粒尺寸及催化剂的表面酸性。在500℃焙烧条件下制备的催化剂性能最佳,优化反应条件下,2-MF转化率100%,2-MTHF选择性为93.5%,反应15 h内催化性能稳定;含碳的有机物在催化剂表面沉积是催化剂失活的主要原因。     

镍前驱体对非负载型镍催化剂上甲烷分解活性的影响

 分别以硝酸镍和乙酸镍为前驱体, 采用沉淀法制备了非负载型 Ni 催化剂, 运用 X 射线衍射、H2-程序升温还原及 CH4 程序升温表面反应对催化剂进行了表征, 并考察了 Ni 催化剂上 CH4 分解反应活性. 结果表明, 以乙酸镍为前驱体制得的 NiO 样品粒子尺寸较小, 较易被还原, 还原后得到的催化剂催化 CH4 分解活性和稳定性较高; 而以硝酸镍为前驱体制得的 NiO 样品粒子尺寸较大, 较难被还原, 还原后催化剂上 CH4 分解活性和稳定性较低. 制备过程中乙酸镍与溶剂乙二醇所形成的配合物是获得尺寸较小 NiO 样品的关键.     

Ni/SiO_2、Ni/TiO_2-SiO_2催化剂上顺酐液相选择加氢合成γ-丁内酯

通过溶胶-凝胶方法结合超临界干燥技术制备了SiO2和TiO2-SiO2复合氧化物气凝胶载体,采用等体积浸渍法制备了Ni/SiO2和Ni/TiO2-SiO2催化剂,运用BET、H2-TPR、XRD、TEM及FT-IR等手段对催化剂进行了表征,并考察了催化剂在顺酐液相选择加氢合成γ-丁内酯反应中的催化性能.结果表明,Ni/TiO2-SiO2催化剂中Ti-O-Si键的形成增强了NiO与载体的相互作用,促进了NiO在载体表面的分散,得到了晶粒较小的活性Ni0物种,表现出高的加氢活性,在H2压力5.0 MPa、反应温度240℃、反应时间6 h的条件下,顺酐转化率为100%,γ-丁内酯的选择性达94.7%.     

Ni2P/TiO2的制备及其对苯加氢反应的催化性能

采用程序升温还原方法制备了TiO2负载的晶态Ni2P催化剂。用X射线衍射（XRD）及低温N2吸附（BET）等技术对样品的物相、比表面积等性质进行了表征。以苯气相加氢为模型反应考察了Ni2P/TiO2催化剂加氢性能，并对Ni2P负载量、前驱体中P的质量分数对催化剂的物相及性能的影响进行了研究。实验结果表明， TiO2负载的晶态磷化镍催化剂上，Ni2P是主要物相。Ni2P/TiO2催化剂对苯加氢反应具有较高的活性、选择性以及良好的稳定性能。Ni2P/TiO2制备对催化剂的性能有影响。Ni2P负载量增加，催化剂的活性先升高后降低，Ni2P负载量为12%时催化剂活性较高。催化剂前驱体中P的质量分数越高，制备出的催化剂对苯加氢反应的稳定性越好，但随前驱体中P的质量分数增加，催化反应的活性先升高，后降低。与Ni2P/SiO2比较，Ni2P/TiO2催化剂具有较高的活性和稳定性。     

TiO2-Al2O3载体的制备及Ni2P/TiO2-Al2O3催化剂上的同时加氢脱硫和加氢脱氮反应

 以溶胶-凝胶法制备的 TiO2-Al2O3 复合氧化物为载体, 采用浸渍法制备了 Ni2P/TiO2-Al2O3 催化剂, 并用 X 射线衍射、N2 吸附脱附、红外和 X 射线光电子能谱等技术对催化剂进行了表征, 考察了载体中 TiO2 含量、焙烧温度及其制备方法对 Ni2P/TiO2-Al2O3 催化剂上同时进行噻吩加氢脱硫和吡啶加氢脱氮反应的影响. 结果表明, 以 Ni/P 摩尔比为 1/2 的前驱体制备的催化剂表面仅出现 Ni2P 物相; 当载体中 TiO2 的含量为 80%, 焙烧温度为 550 oC 时, Ni2P/TiO2-Al2O3 催化剂上加氢脱硫和加氢脱氮的活性最高. 在 360 oC, 3.0 MPa, 氢/油体积比 500, 液时体积空速 2.0 h?1 的条件下, 噻吩和吡啶转化率分别为 61.3%和 64.4%.     

Ni／MgO／Al2O3催化剂中Ni前体对甲烷—二氧化碳重整反应活性的影响

考察了以硝酸镍、氯化镍、硫酸镍、醋酸镍及硝酸六氨合镍5种Ni盐制备的Ni/MgO/Al2O3催化剂在CO2与CH4重整制合成气反应中的催化活性,发现Ni前体对活性有明显的影响,以硝酸镍、醋酸镍、硝酸六氨合镍为前体制备的Ni催化剂,反应性较高;以硫酸镍为前体制备的Ni催化剂,可能由于硫中毒等原因而显示出很低的活性;以氯化镍为前体制备的 Ni催化剂,其活性与制备方法有关,未经烧而直接还原的催化剂显示出较好的活性,X－射线粉末衍射（XRD）、BET比表面积及反应后的积量测定结果表明,以硝酸镍、醋酸镍、硝酸六氨合镍为前体制备的Ni催化剂,表面分散性好,比表面积大,积炭量少。     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.     

Copper-catalyzed multicomponent reactions of 2-iodoanilines,benzylamines, and elemental sulfur toward 2-arylbenzothiazoles

A relatively cheap copper salt-catalyzed, three-component approach providing 2-arylbenzothiazoles in good to excellent yields from readily available 2-iodoanilines, benzylamines, and sulfur powder is reported. This methodology allows preparation of various classes of 2-arylbenzothiazoles and provides a general, reliable approach.