环氧树脂基多孔聚合物整体柱-流动注射联用萃取水中钴离子

采用环氧树脂基多孔聚合物整体柱为管内萃取介质,与流动注射联用固相微萃取水中钴离子.考察了萃取流速、萃取时间和溶液pH值对萃取效果的影响,采用正交试验优化洗脱溶剂、洗脱时间、洗脱流速为:pH=7的钴离子水溶液,以流速0.3 mL/min萃取30 min,再用5％HNO3溶液以0.15 mL/min流速洗脱20 min,采用等离子体原子发射光谱法(ICP-AES)对钴离子进行检测.该方法在0.1～3.0 μg/mL质量浓度范围内呈良好的线性关系,相关系数为0.9993,检出限(S/N=3)为0.03 μg/mL,变异系数小于5％(n＝5).与直接进样相比,富集倍数为3倍,加标回收率高于85％.     

高速逆流色谱双水相体系分离蛋白质

 利用多分离柱高速逆流色谱仪,研究了聚乙二醇1000(PEG1000)-磷酸盐双水相体系的固定相保留率及该体系对蛋白质混合物和鸡蛋清样品的分离。以14.0%PEG1000-16.0%磷酸盐体系的上相为固定相,在流速0.6 mL/min和转速900 r/min的条件下,固定相的保留率达到33.3%。在pH 9.2的PEG1000-磷酸盐双水相体系中，细胞色素C、溶菌酶和血红蛋白的分配系数差异最大,采用该pH值的14.0%PEG1000-16.0%磷酸钾盐双水相体系,在流速1.0 mL/min和转速850 r/min的条件下,成功地分离了这3种蛋白质的混合物。鸡蛋清中的主要蛋白质成分卵转铁蛋白、卵白蛋白和溶菌酶在pH 9.2的15.0%PEG1000-17.0%磷酸钾盐体系中也具有最大的分配系数差异。采用该体系,在流速1.0 mL/min和转速850 r/min的条件下,成功地分离了鸡蛋清样品,得到的卵白蛋白、溶菌酶和卵转铁蛋白的电泳纯度分别为100％,100％和60％,收率均大于90％。     

离子色谱法测定化肥中高氯酸盐

本文研究了化肥中高氯酸盐含量的离子色谱分析方法.选择超声波萃取为样品提取方法并优化了萃取时间.筛选了离子色谱柱,确定使用IonPac AG21+AS21为分离柱;优化了淋洗液浓度和流速,确定以10 mmol/L NaOH为淋洗液,流速为0.3mL/min;进样体积为200μL.方法线性范围为0.1～10 mg/L,相关...     

流动注射-固相萃取-分光光度法检测半导体工业用水中痕量硅

硅酸盐在酸性介质中与钼酸铵反应生成硅钼黄,硅钼黄还原为硅钼蓝后,可被HLB小柱定量萃取.在此基础上,建立了流动注射-固相萃取-分光光度(FI-SPE-Vis)测定水中痕量硅酸盐的新方法.反应生成的硅钼蓝经HLB小柱萃取后,用水清洗去除杂质,NaOH溶液洗脱,分光光度法检测.实验对各参数进行了优化,优化后的参数为:洗脱剂浓度0.01 mol/L;试样上柱流速28.0 mL/min;洗脱流速3.5 mL/min;反应温度45 ℃;硅钼黄与硅钼蓝反应时间均为5 min;钼酸铵混合溶液、草酸溶液、抗坏血酸溶液的用量分别为3.5,3.5和1.75 mL.本方法具有良好的重现性和灵敏度,测定含硅9.33 μg/L的硅酸盐水样7次,RSD值为1.8%;选取不同的试样富集时间,可将定量分析的线性范围扩展为0.47～117 μg/L;检出限0.18 μg/L;回收率为96.8%～105%.可满足特殊工业用水中痕量硅检测的需要.     

固相萃取-气质联用测定水环境中痕量多环麝香

建立了固相萃取-气质联用法测定水中佳乐麝香(HHCB)和吐纳麝香(AHTN)这两种主要的多环麝香的方法.利用Oasis HLB固相萃取小柱预处理水样,通过对固相萃取条件的优化,得出了最佳实验条件:洗脱溶剂为正己烷,洗脱体积为10mL,水样中添加体积分数0.5%甲醇作为有机改性剂,控制上样流速为5～10mL/min,洗脱速率为0.5～2mL/min.该方法线性相关性好,相对标准偏差在1.67%～5.48%之间,对两种多环麝香的方法检测限均为0.025μg/L.利用该方法对污水处理厂进出水中多环麝香进行测定,佳乐麝香和吐纳麝香的去除率分别为61.3%和51.6%.     

顶空固相微萃取-气相色谱质谱法定性定量分析广藿香中的挥发性成分

采用顶空固相微萃取-气相色谱质谱法(HS-SPME/GC-MS)定性定量分析广藿香药材中的挥发性成分.以百秋里醇的峰面积为指标,确定HS-SPME最佳的实验条件为:160目药材粉末用无水 Na2SO4稀释10倍,称取30 mg于15 mL萃取瓶中,以250 r/min速度搅拌预热(80 ℃) 40 min,插入65 μm聚二甲基硅烷-二乙烯(PDMS-DVB)涂层的纤维头,在相同搅拌速度下80 ℃萃取40 min,纤维头进入GC进样口在250 ℃下解吸100 s.GC色谱条件:色谱柱为DB-5MS柱;载气流速为1 mL/min;柱温的起始温度为90 ℃,以0.8 ℃/min升至110 ℃,保持5 min;1.0 ℃/min升至134 ℃,保持5 min;最后以5.0 ℃/min升至143 ℃,保持10 min.结果:百秋里醇的平均回收率为91.8%,RSD为3.0%.运用本方法对10份不同产地广藿香中百秋里醇的含量进行测定,并以其为参比对照,测定了广藿香中其它主要挥发性成分的含量.     

微波辅助萃取-气相色谱测定纺织品中多溴联苯(醚)类阻燃剂

建立了微波辅助萃取-气相色谱-微电子捕获检测纺织品中8种多溴联苯及多溴联苯醚类阻燃剂的方法.通过萃取剂选择实验和正交实验,确定了以25 mL正己烷: 二氯甲烷混合溶剂(2:3, V/V)为萃取剂,萃取温度60℃, 仪器功率400 W,萃取10 min的微波萃取条件,并用流速梯度和柱温程序结合的方法优化了气相色谱分析条件.方法的检出限为0.12～0.99 μg/kg;标准加入回收率为75.5%～112.9%;精密度1.3%～11.8%(n=6),适用于纺织品中痕量多溴联苯(醚)类阻燃剂的监测分析.     

白术挥发性成分的超临界流体萃取及其分析

采用超临界流体萃取白术挥发油成分,对萃取条件进行优化,并用气相色谱、气相色谱－质谱分析鉴定出超临界流体萃了的挥发油中22个化合物。最佳的超临界流体萃取条件为压力22.0MPa,温度60℃,0.5mL乙醇作改性,先静态萃取10min(CO2用量2.0mL),再动态萃取40min(CO2流速为0.3mL/min)。将超临界流体萃取与水蒸气蒸馏进行对比,水蒸气蒸馏5h的油收率仅为超临界流体萃取1h油收率的10.32%,证明超临界流体萃取替代传统萃取的必要性。     

环境水样中百菌清残留的单滴微萃取-反相液相色谱测定

应用单滴微萃取(SDME)-反相液相色谱(RPLC)检测了环境水样中的百菌清残留.优化了单滴微萃取条件:环己烷萃取剂6 μL、单滴体积2 μL、搅拌速率350 r/min、萃取时间40 min、水溶液温度35 ℃、无盐度.水样经单滴微萃取后,使用Hypersil C18柱反相液相色谱分离测定百菌清.反相液相色谱条件:100%甲醇流动相、流速1.0 mL/min、柱温25 ℃、224 nm检测.方法的线性范围、检出限、相对标准偏差和富集倍数分别为1.0 ～50 μg/L、0.02 μg/L、6.1%和427倍.采用该法对环境水样中的百菌清残留进行了测定,环境水样的加标回收率为98% ～106%.     

HPLC-ELSD法测定烟草中的脯氨酸Amadori化合物

为了建立测定烟草中脯氨酸与葡萄糖形成的脯氨酸Amadori(Pro-Amadori)化合物的新方法,对HPLC-ELSD法测定烟草中Pro-Amadori化合物的前处理和测定条件进行了研究.通过甲醇-水溶液在超声波辅助条件下对玉溪C3F烟叶中Pro-Amadori化合物的萃取研究,确定了烟叶前处理的条件:萃取剂甲醇浓度为70%,烟叶与萃取剂料液比为1:30,常温超声萃取时间为15min.HPLC测定条件为:Waters C18反相柱,流动相为甲醇/水=15/85,流速为1mL/min.方法的加标回收率为99.2%,相对标准偏差为1.4%,线性范围为2.0～10μg.     

Determination of trace indium in urine after preconcentration with a chelating-resin-packed minicolumn

A simple and rapid chelating-resin-packed column has been developed for preconcentration of trace indium in biological samples. A large-sized urine sample was pumped through a minicolumn at a flow rate of 1.0 mL/min by using a peristaltic pump, and the eluents were analyzed using graphite furnace atomic absorption spectrometry (GFAAS). Four commercially available chelating resins including Chelex-100, Amberlite IRC-50, Duolite GT-73, and Celite 545-AW were studied for evaluating the indium sorption performance. Several parameters, such as pH, resin amount, eluent volume, eluent flow rate, and the volume of sample, were investigated and optimized. A 100-200 mL of the sample was loaded into a column containing 1.2 g of wet Chelex-100 and subjected to the ion-exchange procedure. The retained analytes were eluted with 5.0 mL of 0.1 M HNO(3) and quantified by GFAAS. The correlation coefficient in the range 10-250 ng/mL was of 0.9994. The limit of detection of the proposed method was 2.75 ng/mL. The method developed was successfully applied to analysis of spiked urine samples with good recoveries of 93-103% (n = 6) and reproducibility (relative standard deviation < 4.9%). The accuracy of procedure was confirmed by indium determination in spiked certified reference materials.     

Sensitive and simple flow injection analysis of formaldehyde using an activated barrel plating nickel electrode

A flow injection analysis coupled with electrochemical detection at an activated barrel plating nickel electrode (Ni-BPE) was developed as a sensitive, simple, and low-cost formaldehyde sensor. The mechanism of Ni-BPE toward the electrocatalytic oxidation of formaldehyde in alkaline medium at ambient temperature was proposed to be based on the electrocatalytic oxidation of formaldehyde by Ni(III)O(OH) species. Under the optimized conditions (flow rate = 1.2 mL/min; detection potential = +0.5 V versus Ag/AgCl), a good linearity in the window of 0.037 to 10 microg/mL formaldehyde was observed, and the LOD of 0.23 microg/L was calculated. The RSDs of intraday (n = 10) and interday (n = 6) replicate measurements of 0.185-5 microg/mL formaldehyde ranged from 1.45 to 3.60%, indicating good reproducibility of the proposed method. The proposed method was successfully applied to the determination of formaldehyde in commercial nail polish samples and a drinking water sample.     

Purification of low-abundance lysozyme in egg white via free-flow electrophoresis with gel-filtration chromatography

As an effective separation tool, free-flow electrophoresis has not been used for purification of low-abundance protein in complex sample matrix. Herein, lysozyme in complex egg white matrix was chosen as the model protein for demonstrating the purification of low-content peptide via an FFE coupled with gel fitration chromatography (GFC). The crude lysozyme in egg while was first separated via free-flow zone electrophoresis (FFZE). After that, the fractions with lysozyme activity were condensed via lyophilization. Thereafter, the condensed fractions were further purified via a GFC of Sephadex G50. In all of the experiments, a special poly(acrylamide- co-acrylic acid) (P(AM-co-AA)) gel electrophoresis and a mass spectrometry were used for identification of lysozyme. The conditions of FFZE were optimized as follows: 130 μL/min sample flow rate, 4.9 mL/min background buffer of 20 mM pH 5.5 Tris-Acetic acid, 350 V, and 14 °C as well as 2 mg/mL protein content of crude sample. It was found that the purified lysozyme had the purity of 80% and high activity as compared with its crude sample with only 1.4% content and undetectable activity. The recoveries in the first and second separative steps were 65% and 82%, respectively, and the total recovery was about 53.3%. The reasons of low recovery might be induced by diffusion of lysozyme out off P(AM-co-AA) gel and co-removing of high-abundance egg ovalbumin. All these results indicated FFE could be used as alternative tool for purification of target solute with low abundance.     

超痕量六价铬分析仪检测制革场地中六价铬

为解决制革等污染场地中Cr(III)-有机络合物会干扰六价铬测定的问题,通过优化仪器色谱条件、在现有行标基础上改进前处理方式,使用超痕量六价铬分析仪检测六价铬,并通过在土壤中投加低、中、高浓度的三价铬、六价铬以及Cr(III)-有机络合物考察三价铬、色度和Cr(III)-有机络合物对六价铬测定的影响。结果表明仪器的最佳色谱条件为：流动相浓度为0.1 mol/L、流动相pH为9、浓硫酸用量为5 mL、流动相流速为1.2 mL/min,衍生试剂流速为0.7 mL/min。样品预处理方式由抽滤提取改进为离心提取,上机前样品pH无需调节,可提高检测效率;该方法与现行行标相比操作简便、耗时短且不受三价铬、样品色度及Cr(III)-有机络合物的干扰。方法精密度和正确度均显著提高,相对标准偏差为1.7%~5.2%,回收率均在94.6%~103%之间。通过与液相色谱-电感耦合等离子体质谱仪对实际样品测定结果的统计学检验发现,结果无显著性差异。该方法适用于制革、电镀等富含Cr(III)-有机络合物场地中六价铬的测定。     

高效液相色谱法检测压敏胶及其制品中的防老剂D

建立了高效液相色谱法测定压敏胶及其制品中防老剂D的分析方法.对样品前处理和色谱分析条件进行了优化,以乙酸乙酯为溶剂,甲醇为沉淀剂,乙腈-水(90:10)为流动相,流速为0.5 mL/min,等度洗脱.采用C18色谱柱,二极管阵列检测器(DAD),高效液相色谱法测定,检测波长为310 nm,外标法定量.并建立了防老剂D的...     

高效液相色谱法测定旋复花中槲皮素的含量

建立了高效液相色谱法测定旋复花中槲皮素含量的方法。该方法采用ZORBAX eclipse XDB C8色谱柱(150mm×4.6mm,5μm),流动相为甲醇-磷酸(0.2%),体积比为65∶35,检测波长为370nm。实验结果表明,槲皮素在5.0～100.0μg/mL范围内与峰面积线性关系良好(r=0.9999),测定结果的相对标准偏差为1.2%(n=6),平均加标回收率为97.1%。该法可用于测定旋复花中槲皮素的含量。     

高效液相色谱法测定烟火药剂中的没食子酸

建立了烟火药剂中没食子酸的高效液相色谱检测方法。采用ZorbaxEclipse XDB-C18色谱柱(4.6×150 mm)分离,以甲醇-0.1%冰乙酸水溶液为流动相,梯度洗脱,流速1.0 mL/min;测定温度为25℃;采用紫外检测器检测,检测波长为274 nm。没食子酸的质量浓度在0.5~20μg/mL时与色谱峰面积之间线性关系良好(相关系数r=0.9999);对烟火药剂样品进行3个不同浓度水平的添加回收,回收率为90.8%~100.2%,相对标准偏差(RSD)为1.2%~6.4%。     

Simultaneous determination of aromatic and terpenic constituents of cloves by means of HPLC with diode array detection

An HPLC method has been developed for the simultaneous determination of aromatic and terpenic constituents of cloves on a C8 RP column, with the mobile phase consisting of a pH 3.5 phosphate buffer-triethylamine (30%) and acetonitrile (70%); a flow rate of 1.2 mL/min and a diode-array detector were used. Complete separation of all analytes (eugenol (EUG), eugenol acetate (AEUG), beta-caryophyllene, a-humulene and caryophyllene oxide) was achieved within 7 min. Good linearity was found in the range 0.125-40.0 microg/mL for EUG and AEUG and in the range 0.250-20.0 microg/mL for the terpenic compounds. After validation, the method was successfully applied to the analysis of clove oil and clove extract samples. The results obtained indicate good accuracy (recovery percentage mean value corresponding to 99.9%) and satisfactory precision.     

流动注射-抑制化学发光法测定岩白菜素

本文基于岩白菜素对鲁米诺-牛血清白蛋白体系化学发光信号显著的抑制作用,建立了快速灵敏测定岩白菜素的流动注射-化学发光分析新方法。实验发现,化学发光强度的降低值与岩白菜素质量浓度对数值呈良好的线性关系,方法的线性范围为3.0~5.0×10~5 pg/mL,检出限(3σ)为1.0pg/mL。当溶液流速为2.0mL/min时,完成一次分析过程仅需30s,采样频率120/h。本法用于片剂、人血清和尿液中岩白菜素的含量测定,回收率为98.1%~102.7%,相对标准偏差小于2.0%(n=7)。同时对化学发光反应机理进行了探讨。