对甲烷氧化偶联W－Mn／SiO＿2催化剂Na＿2WO＿4的流失及其影响的考察

用ＸＲＤ、ＦＴ－ＩＲ、ＥＳＲ、Ｈ２－ＴＰＲ和ＴＰＯ等方法，对Ｎａ２ＷＯ４－Ｍｎ２Ｏ３／ＳｉＯ２催化剂和其经水煮处理的一系列样品进行了表征．实验发现该催化剂中的结晶态Ｎａ２ＷＯ４易于流失，单层分布的Ｎａ２ＷＯ４在苛刻的处理条件下也有可能流失．依此，探讨了上述流失现象与Ｎａ２ＷＯ４－Ｍｎ２Ｏ３／ＳｉＯ２催化剂的催化活性及该催化剂在长时间反应中发生的ＳｉＯ２相变之间的关系，证明了结晶态Ｎａ２ＷＯ４的流失对该催化剂甲烷氧化偶联反应的催化活性只有轻微的影响，单层分布Ｎａ２ＷＯ４的流失可造成催化剂中Ｍｎ从Ｍｎ３＋转变为Ｍｎ２＋，并使催化剂的催化活性明显降低．但在水煮条件下，无论是结晶态的还是单层分布，Ｎａ２ＷＯ４的流失都没有对ＳｉＯ２的α－方石英结构产生影响     

碱金属和氯离子对Mn_2O_3－Na_2WO_4／SiO_2催化剂甲烷氧化偶联反

本文考察了碱金属和氯离子对Ｍｎ２Ｏ３－Ｎａ２ＷＯ４／ＳｉＯ２催化剂甲烷氧化偶联反应性能的影响，结果表明，只有在氯离子和碱金属的共同作用下才能有效地提高Ｃ２烃的收率及其选择性．催化剂经ＮａＣｌ改性后，Ｃ２烃收率为２２％，并可获较高的烯烷比．在考察范围内增加接触时间（Ｗ／Ｆ），催化剂选择性保持不变，但乙烯的选择性呈上升趋势．钠盐Ｎａ２ＷＯ４、Ｎａ４Ｐ２Ｏ７、Ｎａ２ＳＯ４、Ｎａ２ＣＯ３及Ｎａ２Ｂ４Ｏ７对稳定催化剂的贡献按上述顺序逐渐减小．对ＮａＣｌ－Ｍｎ２Ｏ３－Ｎａ２ＷＯ４／ＳｉＯ２催化剂进行了稳定性考察，使用ＸＰＳ、ＸＲＤ和红外光谱对经历不同反应时间的催化剂进行了表征．     

Na-W-Mn/SiO2催化剂活化甲烷的研究Ⅱ.活性氧物种

制备了不同Ｎａ、Ｗ、Ｍｎ组分的Ｎａ－Ｗ－Ｍｎ／ＳｉＯ２催化剂,并进行了Ｏ２程序升温脱附（Ｏ２－ＴＰＤ）和不同温度下Ｎａ－Ｗ－Ｍｎ／ＳｉＯ２催化剂的ＣＨ４脉冲反应（ＣＨ４－ＰＲ）。研究结果表明,Ｎａ－Ｗ－Ｍｎ／ＳｉＯ２催化剂活化甲烷的活笥氧物种是Ｗ和Ｍｎ提供的、高温下易于流动的表面晶格氧（Ｏ＾２－）。Ｎａ和Ｏ＾２－的活泼性具有重要的促进作用,它可以极化Ｗ、Ｍn的金属一氧键,促进Ｏ＾２－的流动性。Ｎａ     

对称电场催化增强甲烷转化合成C_2研究(英文)

利用电场作用通过交流和直流等离子体在低温、常压和低功率下催化反应将甲烷直接转化为碳二烃（乙烷、乙烯、乙炔）。考察了在对称电场作用下催化剂的催化性能。实验结果表明,在交流电场作用下,碳二烃选择性差别不大;甲烷转化率的大小顺序为： ＭｎＯ_２／Ａｌ２Ｏ３＞Ｎｉ／Ａｌ２Ｏ３＞ＭｏＯ_３／Ａｌ２Ｏ３＞Ａｌ２Ｏ３＞Ｎｉ／Ａｌ２Ｏ３＞ＭｏＯ_３／Ａｌ２Ｏ３＞Ｎｉ／ＮａＹ＞Ｐｄ／ＺＳＭ－５＞Ｎｉ／Ｈ４Ｍｇ２Ｓｉ３Ｏ４＞Ｎｉ／ＺＳＭ－５＞Ｃｏ／ＺＳＭ－５＞无催化剂：在直流电场作用下,碳二烃选择性差别也不大（除Ｎｉ／ＮａＹ外）,甲烷转化率的大小顺序为： Ｎｉ／Ａ１２Ｏ３＞Ｎｉ／Ｈ４Ｍｇ２Ｓｉ３Ｏ４＞Ｎｉ／ＺＳＭ－５＞Ｃｏ／ＺＳＭ－５＞ＭｎＯ２／Ａ１２Ｏ３＞ＭｏＯ３／Ａ１２Ｏ３＞Ｎｉ／ＮａＹ＞无催化剂＞Ｐｄ／ＺＳＭ－５。     

甲烷与二氧化碳在Na2WO4—Mn／SiO2催化剂上反应制C2烃及其反应机理的 …

考察了Ｎａ２ＷＯ４－Ｍｎ／ＳｉＯ２催化剂上甲烷与二氧化碳反应制Ｃ２烃及其反应机理，８２０℃时，Ｃ２烃选择性可达９４．５％，随着着温度继续升高，虽然甲烷的转化增加，但Ｃ２烃选择性逐渐降低。Ｏ２－ＴＰＤ，ＣＨ４及脉冲实验表明，８００℃脱附的表面昌格氧为活性氧物种，在催化甲烷活化的同时，ＣＯ２可在该催化剂上活化分解为活性氧物种。     

甲烷与二氧化碳在Na_2WO_4-Mn/SiO_2催化剂上反应制C_2烃及其反应机理的研究

考察了Ｎａ２ＷＯ４－Ｍｎ／ＳｉＯ２催化剂上甲烷与二氧化碳反应制Ｃ２烃及其反应机理，８２０℃时，Ｃ２烃选择性可达９４．５％．随着温度的继续升高，虽然甲烷的转化增加，但Ｃ２烃选择性逐渐降低．Ｏ２－ＴＰＤ、ＣＨ４及脉冲实验表明，８００℃脱附的表面晶格氧为活性氧物种，在催化甲烷活化的同时，ＣＯ２可在该催化剂上活化分解为活性氧物种（ＣＯ２→ＣＯ＋Ｏ＊）．     

对甲烷氧化偶联W—Mn／SiO2催化剂Na2WO4的流失及其影响的考察

用ＸＲＤ，ＦＴ－ＩＲ，ＥＳＲ，Ｈ２－ＴＰＲ和ＴＯＰ等方法，对Ｎａ２ＷＯ４Ｍｎ２Ｏ３／ＳｉＯ２催化剂和其经水煮处理的一系列样品进行一表征。实验发现该催化剂中的结晶态ＮａＷＯ４易于流失，单层分布的Ｎａ２ＷＯ４在苛刻的处理条件下也有可能流失。     

Mn2O3-Na2WO/SiO2催化剂中钨锰间的电子传递作用

Ｍｎ２Ｏ３－Ｎａ２ＷＯ４／ＳｉＯ２催化剂中，Ｍｇ２Ｏ３的引入起到了活化气相氧的作用，由于该催化剂中Ｗ，Ｍｎ间电子的迅速传递，在甲烷氧化偶联反应过程中，甲烷的选择氧化发生在Ｗ位，而气相氧转化为晶格氧发生在Ｍｎ位，从而建立了十分有效的氧化－还原循环，这正是该催化剂较Ｎａ２ＷＯ４／ＳｉＯ２具有更高甲烷选择氧化的活性的原因。     

2%Mn2O3-5%Na2WO4/SiO2催化剂上的甲烷氧化偶联反应动力学

在Ｍｎ２Ｏ３－Ｎａ２ＷＯ４／ＳｉＯ２催化剂上的甲烷氧化偶联反应可用Ｒｉｄｅａｌ－ｒｅｄｏｘ机理描述，它包括均相及多相两个步骤。甲基自由基的生成是一个多相过程，Ｃ２烃的生成是一个均相过程。催化剂的活性同氧化速率和ＣＨ４与表面氧种的反应速率有关，Ｃ２烃的选择性与甲基自由基氧化速率常数和甲基自由基偶联速率常数的比值有关，这些常数均可从实验中求得。     

系列线型［M_2M′S_4O_4］~（2－）簇的合成及光谱与结构的关系（M＝Mo，W；M′＝Co，Mi，Fe）

报道了６种线型簇合物［Ｅｔ_４Ｎ］_２［Ｍ_２Ｍ′Ｓ_４Ｏ_４］（Ｍ＝Ｍｏ，Ｗ；Ｍ′＝Ｃｏ，Ｎｉ，Ｆｅ）的合成，通过对ＵＶ－Ｖ_（ｉｓ）、ＩＲ及ＸＰＳ光谱的对比分析，讨论了簇阴离子［Ｍ_２Ｍ′Ｓ_４Ｏ_４］~２－中心金属Ｍ′的ｄ电子结构、氧化态以及［Ｍ′Ｓ_４］的微环境，由此推测了簇阴离子构型，并讨论了化合物的稳定性．     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

恶臭嗅辨实验室建设探讨

针对恶臭测试的环境影响问题,提出了解决的实例方案,并对方案的要点及优缺点进行讨论,此方案在实际操作中具有较好的效果。     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

解决能源问题的新途径--光解水制氢的研究

面对日益枯竭的能源危机,氢能是一种洁净、最有前景的替代能源。目前在各种制氢的方法中光催化分解水制氢的研究最多,光解水过程中催化剂最关键,本文对利用太阳能光解水的途径、提高光催化反应效率以及光催化剂的开发研究进行了综述。     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

黄酮化合物的合成研究进展

黄酮化合物是一类具有多种生物活性的天然产物,其经典的合成方法主要为查耳酮路线和β-丙二酮路线.近年来出现了许多新技术、新方法.本文介绍了2'-羟基查尔酮的氧化关环法、黄烷酮氧化法、改进的Baker-Venkataraman法及其他合成黄酮化合物的方法.     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.