Selective trace enrichment of acidic pharmaceuticals in real water and sediment samples based on solid-phase extraction using multi-templates molecularly imprinted polymers

A novel multi-templates molecularly imprinted polymer (MIP), using acidic pharmaceuticals mixture (ibuprofen (IBP), naproxen (NPX), ketoprofen (KEP), diclofenac (DFC), and clofibric acid (CA)) as the template, was prepared as solid-phase extraction (SPE) material for the quantitative enrichment of acidic pharmaceuticals in environmental samples and off-line coupled with liquid chromatography–mass spectrometry (LC/MS/MS). Washing solvent was optimized in terms of kind and volume for removing the matrix constituents nonspecifically adsorbed on the MIP. When 1 L of water sample spiked at 1 μg/L was loaded onto the cartridge, the binding capacity of the MIP cartridge were 48.7 μg/g for KEP, 60.7 μg/g for NPX, 52 μg/g for CA, 61.3 μg/g for DFC and 60.7 μg/g for IBP, respectively, which are higher than those of the commercial single template MIP in organic medium (e.g. toluene) reported in the literature. Recoveries of the five acidic pharmaceuticals extracted from 1 L of real water samples such as lake water and wastewater spiked at 1 μg/L were more than 95%. The recoveries of acidic pharmaceuticals extracted from 10-g sediment sample spiked at the 10 ng/g level were in the range of 77.4–90.6%. To demonstrate the potential of the MIP obtained, a comparison with commercial C18 SPE cartridge was performed. Molecularly imprinted solid-phase extraction (MISPE) cartridge showed higher recoveries than commercial C18 SPE cartridge for acidic pharmaceuticals. These results showed the suitability of the MISPE method for the selective extraction of a group of structurally related compounds such as acidic pharmaceuticals.     

Headspace solid phase microextraction in the determination of pesticides in water samples from the Okavango Delta with gas chromatography-electron capture detection and time-of-flight mass spectrometry

Headspace solid phase microextraction (HS-SPME) was optimized for the analysis of pesticides with gas chromatography electron capture detection (GC-ECD) and high-resolution mass spectrometry. Factors influencing the extraction efficiency such as fiber type, extraction mode and temperature, effect of ionic strength, stirring and extraction time were evaluated. The lowest pesticide concentrations that could be detected in spiked aliquots after HS-SPME–GC-ECD ranged from 0.0005 to 0.0032 μg L^{− 1}. Consequently hexachlorobenzene, trans-chlordane, 4,4′-DDD and 4,4′-DDE were detected in water samples after HS-SPME at concentrations ranging from 2.4 to 61.4 μg L^{− 1} that are much higher than the 0.1 μg L^{− 1} maximum limit of individual organochlorine pesticides in drinking water set by the European Community Directive. The same samples were cleaned with ISOLUTE C₁₈ SPE sorbent with an optimal acetone/n-hexane (1:1 v/v) mixture for the elution of analytes. No pesticides were detected after SPE clean-up and pre-concentration. Precision for both methods was satisfactory with relative standard deviations less than 20%. This work demonstrated the superiority of HS-SPME as a sample clean-up and pre-concentration technique for pesticides in water samples as well as the need to identify and control point sources of pesticides.     

Simultaneous determination of seven nitrogen‐containing phenyl ethers in cosmetics by gas chromatography with mass spectrometry and dispersive solid‐phase extraction

An analytical method was established for the simultaneous determination of seven nitrogen‐containing phenyl ethers (2‐anisidine, 3‐anisidine, 4‐anisidine, 2‐nitroanisole, 3‐nitroanisole, 4‐nitroanisole, and 3,3'‐dimethoxybenzidine) in cosmetics by gas chromatography with mass spectrometry in this work. The samples were extracted with ethyl acetate and purified with primary secondary amine during the dispersed solid‐phase extraction. The analytes were separated by a DB‐17MS column and detected in the electron ionization mode of mass spectrometry in the selected ions monitoring mode. The extraction solvent, purification adsorbents, and chromatographic column behavior were optimized. The results indicated that the seven analytes show good linear relationship (R ² > 0.9965) in the concentrations of 5.0–5000 μg/L. The quantitation limits of the method ranged from 19.0 to 84.8 μg/kg. The recovery rates of seven analytes were in the range of 72.6–114% with the relative standard deviations of 1.1–7.5%. Real sample analyses showed that this accurate and precise method could be appropriate for simultaneous determination of seven nitrogen‐containing phenyl ethers in cosmetics.     

Magnetic field assisted μ-solid phase extraction of anti-inflammatory and loop diuretic drugs by modified polybutylene terephthalate nanofibers

A magnetic nanocomposite consisting of nanoparticles–polybutylene terephthalate (MNPs–PBT) was electrospun and used as an extracting medium for an on-line μ-solid phase extraction (μ–SPE)–high performance liquid chromatography (HPLC) set–up with an ultraviolet (UV) detection system. Due to the magnetic property of the prepared nanofibers, the whole extraction procedure was implemented under an external magnetic field to enhance the extraction efficiencies. The developed method along with the synthesized nanocomposite were found to be appropriate for the determination of trace levels of selected drugs including furosemide, naproxen, diclofenac and clobetasol propionate in the urine sample. The prepared MNPs-PBT electrospun nanocomposite was characterized using the scanning electron microscopy (SEM), energy dispersive spectroscopy (EDX) and Fourier transform infrared (FT–IR) spectroscopy. The prepared magnetic fibers showed high porosity, which was another driving force for the extraction efficiency enhancement. Major parameters affecting the extraction efficiency of the selected drugs were optimized. The limits of detections (LOD) of the studied drugs were in the range of 0.4–1.6 μg L⁻¹ and the limits of quantification (LOQ) were 1–4 μg L⁻¹ under the optimized conditions. Relative standard deviation (RSD%) for three replicates at three concentration levels of 6, 100 and 400 μg L⁻¹ were 5.9–8.0% while acceptable linear range with two orders of magnitude was obtained (R² = 0.99). The method was validated by the determination of the selected drugs in urine samples and the results indicated that this method has sufficient potential for enrichment and determination of the desired drugs in the urine sample. The relative recovery values were found to be in the range of 78–91%. Implementing the developed on–line μ–SPE method under the external magnetic field induction, led to higher extraction efficiencies for the selected drugs with various diamagnetic properties.     

Sensitive method for the determination of lipophilic marine biotoxins in extracts of mussels and processed shellfish by high-performance liquid chromatography–tandem mass spectrometry based on enrichment by solid-phase extraction

A solid-phase extraction (SPE) method for the enrichment and clean-up of lipophilic marine biotoxins from extracts of different species of bivalve molluscs and processed shellfish products was developed. Okadaic acid (OA), pectenotoxin2 (PTX2), azaspiracid1 (AZA1) and yessotoxin (YTX) were determined by LC–MS/MS in hydrolyzed and non-hydrolyzed extracts. Applying a concentration factor of 10 the limit of quantification for the four toxins was determined to be 1 μg/kg. An organized in-house ring trial proved transferability of the method protocol and satisfactory results for all four toxins with a relative standard deviation (RSD) of 5–12%. The precision of the whole method including LC–MS detection was determined by processing seven independent extractions analyzed in independent sequences. RSD ranged between 12% and 24%. This SPE method was tested within a concentration range corresponding to the range of the current European Union regulatory limits (up to 160 μg/kg for the OA group), but it would also be applicable to a lower μg/kg range which is important in view of a possible decrease of regulatory limits as proposed by a working group of the European Food Safety Authority. The potential of SPE as a cleaning tool to cope with matrix effects in LC–MS/MS was studied and compared to liquid–liquid portioning.     

Stripping voltammetric analysis of organophosphate pesticides based on solid-phase extraction at zirconia nanoparticles modified electrode

A sensitive electrochemical stripping voltammetric method for analyzing organophosphate (OP) compounds was developed based on solid-phase extraction (SPE) at zirconia (ZrO₂) nanoparticles modified electrode. ZrO₂ nanoparticles were proved as a new sorbent for SPE of OP pesticides. Because of the strong affinity of ZrO₂ for the phosphoric group, nitroaromatic OPs can strongly bind to the ZrO₂ nanoparticle surface. The combination of SPE with square-wave voltammetry (SWV) provided a fast, sensitive, and selective electrochemical method for nitroaromatic OP compounds using methyl parathion (MP) as a model. The stripping response was highly linear over the MP range of 0.003–2.0 μg/mL, with a detection limit of 0.001 μg/mL. The fast extraction ability of ZrO₂ nanoparticles makes it promising sorbent for various solid-phase extractions.     

High performance liquid chromatography–tandem mass spectrometry for the analysis of 10 pesticides in water: A comparison between membrane-assisted solvent extraction and solid phase extraction

This work describes the application of two sample preparation methods: membrane-assisted solvent extraction (MASE) and solid phase extraction (SPE) in combination with high performance liquid chromatography–tandem mass spectrometry (HPLC–MS–MS) for the determination of 10 pesticides in surface and ground water. Optimal extraction conditions for MASE were 60 min extraction time at 30 °C with a solvent volume of 100 μL toluene. 5 μL of the toluene extract were directly injected in the HPLC–MS–MS system. Concerning SPE, two materials were tested and C18 was superior to Oasis HLB. Complete desorption was ensured by desorbing the SPE (C18) cartridge with 3 mL of an acetonitrile/methanol mixture (1:1). After evaporation, the extract was injected in the analytical system. Analyte breakthrough was not found for the investigated compounds. For both methods, high extraction yields were achieved, in detail 71% (metalaxyl) till 105% (linuron) for MASE and 52% (ethiofencarb) till 77% (prometryne) for SPE (C18). Detection limits were in the low ng/L range for both methods and precision, expressed as the relative standard deviation (RSD) of the peak areas was below 13%. Five real water samples were analyzed applying both extraction methods. The results were in good agreement and standard addition proved that no matrix effects (such as ion suppression) occurred. In this comparison SPE has the potential of larger sensitivity whereas faster analysis and slightly better recoveries were achieved with MASE. MASE shows potential to be a promising alternative to the conventional off-line SPE concerning low to medium polar compounds.     

Date pits waste as a solid phase extraction sorbent for the analysis of lead in wastewater and for use in manufacturing brick: An eco-friendly waste management approach

Lead (Pb(II)), an extremely hazardous heavy metal that has been shown to have detrimental effects on both the environment and humans, mostly gets into the ecosystem through industrial activities. In this work, a new solid-phase extraction (SPE) based on treated date pits bio-sorbent and iCAP Q inductively-coupled plasma mass spectrometry (iCAP Q ICP/MS) method has been optimized for the trace determination of Pb(II) in various industrial wastewater effluents. A cost-effective biomass material was prepared from date pits (DP), and chemically modified with H₂O₂ and successively used as SPE bio-sorbent for Pb(II) extraction. Extracting solutions for instance H₂SO₄, HNO₃ and HCl at various concentrations (1–5 mM) were optimized, and best extraction of Pb(II) was obtained by HCl (1 mM). The optimized SPE and iCAP Q ICP/MS method has offered excellent validation conditions in terms of coefficient of determination (CoD, R² > 0.999), detection limit (DL, 0.011 µg/L), quantification limit (QL, 0.034 µg/L), and run-to-run and day-to-day precision (RSD < 6 %). The optimized procedure was practically applied in the determination of Pb(II) in industrial wastewater comprising iron and steel, textile, printing and battery industries. Among the analyzed samples, the battery industry produced higher amounts of Pb(II) (18.55 µg/L) followed by iron and steel (14.65 µg/L), petroleum (12.38 µg/L) printing (5.78 µg/L) and textile (3.76 µg/L) industries. The recovery values were achieved between 95 % and 99 %. The obtained results have established the appropriateness of the offered technique as a new useful method for the routine examination of Pb(II) in industrial wastes. In addition, the current method could be expansively used in the proficient removal and identification of other heavy metals contaminants from similar matrices. Further, the metal ions saturated bio-sorbents were used in the preparations of bricks and it was found to be a successful approach for heavy metals and agricultural waste management.     

Effective extraction of triazines from environmental water samples using magnetism-enhanced monolith-based in-tube solid phase microextraction

This article reports on the effective extraction of triazines from environmental water samples using magnetism-enhanced monolith-based in-tube solid phase microextraction (ME-MB/IT-SPME). Firstly, monolithic poly (octyl methacrylate-co-ethyleneglycol dimethacrylate) capillary column doped with magnetic nanoparticles was synthesized inside a fused silica. After that, the monolithic capillary column was placed inside a magnetic coil that allowed the exertion of a variable magnetic field during adsorption and desorption steps. The effects of intensity of magnetic field, adsorption and desorption flow rate, volume of sample and desorption solvent, pH value and ionic strength in sample matrix on the performance of ME-MB/IT-SPME for triazines were investigated in details. Under the optimized conditions, the developed ME-MB/IT-SPME showed satisfactory quantitative extraction efficiencies of the target analytes between 64.8% and 99.7%. At the same time, the ME-MB/IT-SPME was combined with high-performance liquid chromatography with diode array detection to detect six triazines in water samples. The limits of detection (S/N = 3) and limits of quantification (S/N = 10) were in the ranges of 0.074–0.23 μg/L and 0.24–0.68 μg/L, respectively. The precision of the proposed method was evaluated in terms of intra- and inter-assay variability calculated as relative standard deviation, and it was found that the values were all below 10%. Finally, the developed method was successfully applied for environmental water samples such as farmland, lake and river water with spiked recoveries in the range of 70.7–119%.     

Analysis of microcystins using high‐performance liquid chromatography and magnetic solid‐phase extraction with silica‐coated magnetite with cetylpyridinium chloride

Microcystins (MCs), produced by freshwater cyanobacteria, can be serious water pollutants, so it is important to monitor their concentration in drinking water. We have developed a method for rapid and accurate determination of microcystin levels in environmental water, using magnetic solid‐phase extraction and high‐performance liquid chromatography with UV detection. The magnetic composite material, which was combined with cetylpyridinium chloride, was prepared by hydrothermal synthesis. The optimal extraction of microcystins in water sample was achieved by optimizing the amount of adsorbent, time of adsorption, ratio of eluting solvent, and volume of eluent. Under the optimal conditions, the limit of detection of MC‐LR was 0.001 μg/L, and the limit of quantification was 0.0028 μg/L. The limit of detection of MC‐RR was 0.001 μg/L, and the limit of quantification was 0.003 μg/L. These values are far lower than those established by the International Health Organization for the maximum concentration of microcystins in drinking water. The magnetic solid‐phase extraction adsorbent used in this method has the advantages of simple preparation, low price, and easy solid–liquid separation, and it can be used for the rapid and sensitive monitoring of trace microcystins in environmental water samples.     

Sensitive determination of typical phenols in environmental water samples by magnetic solid‐phase extraction with polyaniline@SiO2@Fe as the adsorbents before HPLC

A novel magnetic core–shell material polyaniline@SiO₂@Fe (PANI@SiO₂@Fe) has been successfully synthesized and investigated as an effective adsorbent for the magnetic solid‐phase extraction of typical endocrine disrupting compounds such as bisphenol A, tetrabromobisphenol A, and 4‐nonylphenol from water samples. The morphology of the as‐prepared PANI@SiO₂@Fe was characterized by transmission electron microscopy and X‐ray diffraction. The main parameters that influenced the enrichment performance such as the kind of eluent, amount of adsorbent, volume of eluent, adsorption time, elution time, ionic strength, pH, concentration of humic acid, and sample volume were investigated. Under the optimal conditions, a good linear relationship was found in the range of 0.05–100 μg/L for bisphenol A, 0.05–300 μg/L for tetrabromobisphenol A, and 0.05–250 μg/L for 4‐nonylphenol, respectively. The correlation coefficients are all above 0.995. The limits of detection were in the range of 0.009–0.04 μg/L, and precisions were under 3.73% (n  = 6). The real water analysis indicated that the spiked recoveries were in the range of 92.9–98.9% (n  = 3). All these results indicated that the developed method was an efficient tool for the analysis of bisphenol A, tetrabromobisphenol A, and 4‐nonylphenol.     

Innovative separation and preconcentration technique of coagulating homogenous dispersive micro solid phase extraction exploiting graphene oxide nanosheets

A uniquely novel, fast, and facile technique is introduced for the first time in which a scant amount of graphene oxide (GO), without modification, has been utilized in dispersive mode of solid phase extraction (SPE) for an efficient yet simple separation. The proposed method of coagulating homogenous dispersive micro solid phase extraction (CHD-µSPE) is based on coagulation of homogeneous GO solution with the aid of polyetheneimine (PEI). CHD-µSPE use full adsorption capacity of GO because in this method was used GO solution obtained from synthesis process without drying step and stacking nanosheets. In optimized condition, 30 µL GO solution (7 mg mL⁻¹), obtained in synthesis process, was injected into 1.5 mL the sample solution followed by immediate injection of 53 µL PEI solution (1 mg mL⁻¹). After inserting PEI, GO sheets aggregate and can be readily separated by centrifugation. PEI not only cause aggregation of GO, but also form three-dimensional network of GO with easy handling in following separation steps. Lead, cadmium, and chromium were selected as model analytes and the effecting parameters including the amount of GO, concentration of PEI, sample pH, extraction time, and type of desorption solvent were investigated and optimized. The results indicate that the proposed CHD-µSPE method can be successfully applied GO in dispersive mode of SPE without effecting on good capability adsorption of GO. The novel method was applied in determination of lead, cadmium, and chromium in water, human saliva, and urine samples by electrothermal atomic absorption spectrometry. The detection limits are as low as 0.035, 0.005, and 0.012 µg L⁻¹ for Pb, Cd, and Cr respectively. The intra-day precisions (RSDs) were lower than 3.8%. CHD-µSPE method showed a good linear ranges of 0.24–15.6, 0.015–0.95 and 0.039–2.33 µg L⁻¹ for Pb, Cd and Cr respectively. Method performance was investigated by determination of mentioned metal ions in river water, human urine and saliva sample with good recoveries in range of 94.2–103.0%. The accuracy of the method was underpinned by correct analysis of a standard reference material (SRM: 2668 level I, Urine).     

Direct synthesis of nitrogen-doped graphene on platinum wire as a new fiber coating method for the solid-phase microextraction of BXes in water samples: Comparison of headspace and cold-fiber headspace modes

In this work, a new solid-phase microextraction fiber was prepared based on nitrogen-doped graphene (N-doped G). Moreover, a new strategy was proposed to solve problems dealt in direct coating of N-doped G. For this purpose, first, Graphene oxide (GO) was coated on Pt wire by electrophoretic deposition method. Then, chemical reduction of coated GO to N-doped G was accomplished by hydrazine and NH₃. The prepared fiber showed good mechanical and thermal stabilities. The obtained fiber was used in two different modes (conventional headspace solid-phase microextraction and cold-fiber headspace solid-phase microextraction (CF-HS-SPME)). Both modes were optimized and applied for the extraction of benzene and xylenes from different aqueous samples. All effective parameters including extraction time, salt content, stirring rate, and desorption time were optimized. The optimized CF-HS-SPME combined with GC-FID showed good limit of detections (LODs) (0.3–2.3 μg/L), limit of quantifications (LOQs) (1.0–7.0 μg/L) and linear ranges (1.0–5000 μg/L). The developed method was applied for the analysis of benzene and xylenes in rainwater and some wastewater samples.     

On-line solid-phase extraction-HPLC-fluorescence detection for simultaneous determination of puerarin and daidzein in human serum

Response surface methodology (RSM) was applied to the optimization of on-line solid-phase extraction (SPE) parameters, and an automated system of on-line SPE coupled with high-performance liquid chromatography (HPLC) with fluorescence detection was developed for the determination of puerarin and daidzein in human serum. The human serum sample of 50 μL was injected into a conditioned C18 SPE cartridge, and the matrix was washed out with acetonitrile-KH₂PO₄-triethylamine buffer (0.01 M, pH 7.4) (3:97, v/v) for 3 min at a flow rate of 0.25 mL/min. Then the target analytes were eluted and transferred to the analytical column. A chromatographic gradient elution was programmed with the mobile phase consisting of acetonitrile and KH₂PO₄-triethylamine buffer, and the analytes were determined with a fluorescence detector at excitation wavelength of 350 nm and emission wavelength of 472 nm, respectively. The proposed method presented good linear relations (0.85-170 μg/mL for puerarin and 0.2-40 μg/mL for daidzein), satisfactory precision (RSD < 8%), and accredited recovery (92.5-107.8%).     

Comparison of off- and in-line solid-phase extraction for enhancing sensitivity in capillary electrophoresis using ochratoxin as a model compound

This paper proposes and compares two approaches based on off- and in-line solid-phase extraction (SPE), intended to enhance sensitivity in capillary electrophoresis with ultraviolet detection (CE-UV) using as a model the determination of ochratoxin A (OA) in river water samples. In the off-line SPE mode, the reversed-phase sorbent (octadecilsylane, C₁₈) selectively retains the target analyte (OA) and allows large volumes of the sample (70 mL) to be introduced and subsequently eluted in a small volume (0.1 mL) of an appropriate solution. In the in-line SPE mode, a custom-made microcartridge is inserted near the inlet of the capillary, which is filled with the same C₁₈ sorbent. This solid phase selectively retains OA present in a sample volume as low as approximately 640 μL for subsequent elution with ca. 135 nL of an appropriate eluent. The limit of detection (LOD) obtained with the in-line SPE method was 1 ng L^-1, which is 3 orders of magnitude lower than that obtained with CE-UV and roughly 1 order lower than that provided by the off-line SPE-CE-UV method.     

Dispersive solid‐phase extraction of buprenorphine from biological fluids using metal‐organic frameworks and its determination by ultra‐performance liquid chromatography

In this work, various types of metal‐organic frameworks were synthesized, and their affinities toward buprenorphine were evaluated using dispersive solid‐phase extraction. The extracted buprenorphine was determined by ultra high performance liquid chromatography‐ultraviolet detection system. The highest extraction recovery was observed by employing zeolitic imidazole framework‐67. Then, a facile and fast extraction method was designed for the extraction and purification of the target drug. Optimization of the extraction method was carried out by the design of experiment approach. A linearity range of 1–1000 μg/L with the limit of detection of 0.15 μg/L and relative standard deviations (50 μg/L, n = 5) of 3.4% was obtained for standard sample analysis. Under optimized experimental and instrumental conditions, the relative recoveries were in the range of 95 to 111%. Eventually, zeolitic imidazole framework‐67 was successfully employed for the extraction and determination of buprenorphine in the biological fluids with satisfactory results.     

Investigation of ractopamine molecularly imprinted stir bar sorptive extraction and its application for trace analysis of β2-agonists in complex samples

In this paper, a novel molecularly imprinted polymer (MIP) coated stir bar with ractopamine as template by glass capillary filling with magnetic core as substrate was prepared reproducibly. The ractopamine MIP coating was homogeneous and porous with the average thickness of 20.6 μm. The extraction apparatus for the stir bar was improved to avoid coating loss. The MIP-coated stir bar showed better extraction capacity and good selectivity than that of non-imprinted polymer (NIP) coated stir bar to ractopamine and its analogues. The extraction capacities of ractopamine, isoxsuprine, clenbuterol and fenoterol for MIP-coated stir bar were 3.3, 3.1, 2.8 and 2.4 times as much as that of the NIP coated stir bar, respectively. The MIP-coated stir bars could be used at least 40 times without apparent damage and kept in dried air for 8 months without reduce of extraction ability. A method for the determination of β₂-agonists in complex samples by MIP-coated stir bar sorptive extraction coupled with high-performance liquid chromatography (HPLC) was developed. The linear ranges were 0.5–40 μg/L for ractopamine and 1.0–40 μg/L for isoxsuprine and clenbuterol. The detection limits were within the range of 0.10–0.21 μg/L. The method was successfully applied to the analysis of β₂-agonists in spiked pork, liver and feed samples with the recoveries of 83.7–92.3%, 80.5–90.2% and 73.6–86.2%, respectively. The RSDs was within 2.9–8.1%. The method is very suitable for the determination of trace β₂-agonists in pork, liver and feed samples.     

Sucralose screening in European surface waters using a solid-phase extraction-liquid chromatography–triple quadrupole mass spectrometry method

An analytical method was developed for the analysis of sucralose, a persistent chlorinated calorie-free sugar substitute, in surface waters. The method is based on solid-phase extraction (SPE) of 400 mL water using Oasis HLB (Waters) adsorber material, followed by negative electrospray ionization (ESI) triple quadrupole LC–MS–MS detection. Quantification was performed by external calibration, as well as by isotope dilution with deuterated sucralose d6 internal standard. Extraction with Oasis HLB, a polymeric adsorbent suited for polar compounds, was much more efficient at neutral pH than at pH 3; a recovery of 62 ± 9% (n = 6; determined at 1 μg/L) could be achieved. Strong ion suppression caused by matrix substances was observed for sucralose in the SPE extracts. The analysis of 120 river surface water samples from 27 European countries showed that sucralose, which is in use in Europe since beginning 2005, can be found in the aquatic environment, at concentrations up to 1 μg/L. Sucralose was predominately found in samples from the UK, Belgium, the Netherlands, France, Switzerland, Spain, Italy, Norway, and Sweden, suggesting an increased use of the substance in Western Europe.     

Fiber-packed SPE tips based on electrospun fibers

A novel fiber-packed solid-phase extraction (SPE) tip was designed based on electrospun nanofibers. The tip was used to investigate the extraction of hydrocortisone (HC), cortisone acetate (CA), ethinylestradiol (EE), and estradiol (E2). The effects of diameters, porous figurations, and functional groups of the electrospun fibers on the selectivity and efficiency were studied. The experimental results indicated that the detection limit of cortisol in water sample could be as low as 0.75 ng/mL. When the tip is used for detection of cortisol in human hair the efficiency of biological sample pretreatment is better than the traditional SPE method. Our method could significantly simplify the traditional SPE process and lower the cost. Industrial application of the tip is anticipated. Figure Analyte molecules (e.g., cortisol) are attracted onto the electrospun nanofibers of the packed SPE tip. Careful selection of the fiber diameter, morphology, and functional groups affords high selectivity, sensitivity, and extraction recoveries Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Flotation/ultrasound‐assisted microextraction followed by HPLC for determination of fat‐soluble vitamins in multivitamin pharmaceutical preparations

Dissolved carbon dioxide flotation–emulsification microextraction technique coupled with high‐performance liquid chromatography was developed for separation and determination of fat‐soluble vitamins (A, D₃, E, and K₃) in multivitamin pharmaceutical preparations. Dissolved carbon dioxide flotation was used to break up the emulsion of extraction solvent in water and to collect the extraction solvent on the surface of aqueous sample in narrowed capillary part of extraction cell. Carbon dioxide bubbles were generated in situ through the addition of 300 μL of concentrated hydrochloric acid into the alkaline sample solution at pH = 11.5 (1% w/v sodium carbonate), which was sonicated to intensify the carbon dioxide bubble generation. Several factors affecting the extraction process were optimized. Under the optimal conditions, the limits of detection were 0.11, 0.47, 0.20 and 0.35 μg/L for A, E, D₃, and K₃ vitamins in water samples, respectively. The inter‐day and intra‐day precision of the proposed method were evaluated in terms of the relative standard deviation and were <10.5%.