Effect of Enzyme and Cofactor Immobilization on the Response of Ethanol Oxidation in Zirconium Phosphate Modified Biosensors

Two different self‐contained ethanol amperometric biosensors incorporating layered [Ru(phend)₂bpy]²⁺‐intercalated zirconium phosphate (ZrP) as the mediator as well as yeast‐alcohol dehydrogenase (y‐ADH) and its cofactor nicotinamide adenine dinucleotide (NAD⁺) were constructed to improve upon a design previously reported where only this mediator was immobilized in the surface of a modified electrode. In the first biosensor, a [Ru(phend)₂bpy]²⁺‐intercalated ZrP modified carbon paste electrode (CPE) was improved by immobilizing in its surface both y‐ADH and NAD⁺ using quaternized Nafion membrane. In the second biosensor, a glassy carbon electrode was modified with [Ru(phend)₂bpy]²⁺‐intercalated ZrP, y‐ADH, and NAD⁺ using Nafion as the holding matrix. Calibration plots for ethanol sensing were constructed in the presence and absence of ZrP. In the absence of ZrP in the surface of the modified glassy carbon electrode, leaching of ADH was observed as detected by UV‐vis spectrophotometry. Ethanol sensing was also tested in the presence and absence of ascorbate to measure the selectivity of the sensor for ethanol. These two ethanol biosensors were compared to a previously reported one where the y‐ADH and the NAD⁺ were in solution, not immobilized.     

Synthesis,characterization and DNA binding and photocleavage studies of [Ru(bpy)2BDPPZ]2+, [Ru(dmb)2BDPPZ]2+ and [Ru(phen)2BDPPZ]2+ complexes and their antimicrobial activity

Polypyridyl ligand 9a,13a‐dihydro‐4,5,9,14‐tetraaza‐benzo[b]triphenylene‐11‐yl)‐phenyl‐methanone (BDPPZ) and its complexes [Ru(bpy)₂BDPPZ]²⁺, [Ru(dmb)₂BDPPZ]²⁺ and [Ru(phen)₂BDPPZ]²⁺ (where bpy = 2,2′‐bipyridine, dmb = 4,4′‐dimethyl‐2,2′‐bipyridine, phen = 1,10‐phenanthroline) have been synthesized and characterized by elemental analysis, IR, UV–vis, ¹H‐NMR, ¹³C‐NMR and mass spectra. The DNA‐binding properties of the complexes were investigated by absorption, emission, melting temperature and viscosity measurements. Experimental results indicate that the three complexes can intercalate into DNA base pairs. Photo activated cleavage of pBR‐322 DNA by the three complexes was also studied. Further, all three Ru(II) complexes synthesized were screened for their antimicrobial activity. Copyright © 2009 John Wiley & Sons, Ltd.     

Direct intercalation of bis-2,2',2″,6-terpyridylcobalt(III) into zirconium phosphate layers for biosensing applications

The direct intercalation reaction of [Co(tpy)(2)](2+) with the highly hydrated θ phase of layered zirconium phosphate (θ-ZrP) resulted in the formation of the oxidized [Co(tpy)(2)](3+) ion within the ZrP material. The X-ray powder diffraction patterns showed that the interlayer distance increases from 10.3 ? in θ-ZrP to 14.9 ? in the dry [Co(tpy)(2)](3+)-intercalated ZrP {[Co(tpy)(2)](3+):ZrP} phase. The complex remains electroactive within the layers of ZrP. The formal potential of a carbon paste electrode (CPE) modified with [Co(tpy)(2)](3+):ZrP (E°' = 40.8 mV versus Ag/AgCl, 3.5 M NaCl) is non-pH-dependent. However, the sensitivity of the [Co(tpy)(2)](3+):ZrP-modified CPE for the detection of reduced nicotinamide adenine dinucleotide (NADH) electrooxidation was lower than that of a previously reported CPE modified with [Ru(phend)(2)bpy](2+)-intercalated ZrP. (1) To improve the characteristics of NADH electrooxidation of the [Co(tpy)(2)](3+):ZrP-modified CPE, we included the enzyme diaphorase in solution, which increased the electrocatalytic current for NADH oxidation. A bienzymatic lactate biosensor was constructed and used for lactate sensing.     

Enhanced Electrochemiluminescence from a Stoichiometric Ruthenium(II)–Iridium(III) Complex Soft Salt

Electrochemiluminescence (ECL) and electrochemistry are reported for a heterometallic soft salt, [Ru(dtbubpy)₃][Ir(ppy)₂(CN)₂]₂ ( [Ir][Ru][Ir] ), consisting of a 2:1 ratio of complementary charged Ru and Ir complexes possessing two different emission colors. The [Ru]²⁺ and [Ir]^? moieties in the [Ir][Ru][Ir] greatly reduce the energy required to produce ECL. Though ECL intensity in the annihilation path was enhanced 18× relative to that of [Ru(bpy)₃]²⁺, ECL in the co‐reactant path with tri‐n‐propylamine was enhanced a further 4×. Spooling spectroscopy gives insight into ECL mechanisms: the unique light emission at 634 nm is due to the [Ru]²⁺* excited state and no [Ir]^?* was generated in either route. Overall, the soft salt system is anticipated to be attractive and suitable for the development of efficient and low‐energy‐cost ECL detection systems.     

Hetero‐ and homo‐leptic Ru(II) catalyzed synthesis of cyclic carbonates from CO2; Synthesis,spectroscopic characterization and electrochemical properties

Based on the a ligand BDPPZ [(9a,13a‐dihydro‐4,5,9,14‐tetraaza‐benzo[b]triphenylene‐11‐yl)‐phenyl‐methanone] (1) and its polypyridyl hetero‐ and homoleptic Ru(II) metal complexes, [Ru(bpy)₂L](PF₆)₂ (2), [Ru(phen)₂L](PF₆)₂ (3), [Ru(dafo)₂L](PF₆)₂ (4), [Ru(dcbpy)₂L](PF₆)₂ (5) and [RuL₃](PF₆)₂ (6) (where, L = ligand, bpy = 2,2′‐bipyridine, phen = 1,10‐phenantroline, dafo = 4,5‐diazafluoren‐9‐one and dcbpy = 3,3′‐dicarboxy‐2,2′‐bipyridine), have been synthesized and characterized by elemental analysis, UV–vis, FT‐IR, ¹H and ¹³C‐NMR spectra (for ligand), molar conductivity measurements and X‐ray powder techniques. The electrochemical parameters of the substituted ligand and its polypyridyl hetero‐ and homoleptic Ru(II) metal complexes are reported by cyclic voltammetry. UV–vis spectroscopy is used to compare the differences between the conjugated π systems in this ligand and its Ru(II) metal complexes. The polypyridyl hetero‐ and homoleptic Ru(II) metal complexes also tested as catalysts for the formation of cyclic organic carbonates from carbon dioxide and liquid epoxides which served as both reactant and solvent. The results showed that the [Ru(L)₃](PF₆)₂ (6) complex is more efficient than the other Ru(II) complexes for the formation of cyclic organic carbonates from carbon dioxide. Copyright © 2010 John Wiley & Sons, Ltd.     

Assessing a Spectroelectrochemical Sensor’s Performance for Detecting [Ru(bpy)3]2+ in Natural and Treated Water

A spectroelectrochemical sensor that combines three modes of selectivity in a single device was evaluated in natural and treated water samples using tris‐(2,2′‐bipyridyl) ruthenium(II) dichloride hexahydrate, [Ru(bpy)₃]²⁺, as a model analyte. The sensor was an optically transparent indium tin oxide (ITO) electrode coated with a thin film of partially sulfonated polystyrene‐block‐poly(ethylene‐ran‐butylene)‐block‐polystyrene (SSEBS). As the potential of the ITO electrode was cycled from +0.7 to +1.3 V, the analyte changed from the colored [Ru(bpy)₃]²⁺ complex to colorless [Ru(bpy)₃]³⁺ complex and the change in absorbance at 450 nm was used as the optical signal for quantification. Calibration curves were obtained for [Ru(bpy)₃]²⁺ in natural well water, river water and treated tap water with detection limits of 108, 139 and 264 nM, respectively. A standard addition method was developed to determine an ‘unknown’ spike addition concentration of [Ru(bpy)₃]²⁺ in well water. The spectroelectrochemical sensor determined the concentration of [Ru(bpy)₃]²⁺ spiked into a sample of Hanford well water to be 0.39±0.03 µM versus the actual concentration of 0.40 µM.     

Synthesis,Characterization, and DNA‐Binding Properties of the Chiral Ruthenium(II) Complexes Δ‐ and Λ‐[Ru(bpy)2(dmppd)]2+ (dmppd = 10,12‐Dimethylpteridino[6,7‐f] [1,10]phenanthroline‐11,13(10H,12H)‐dione; bpy = 2,2′‐Bipyridine)

Two novel chiral ruthenium(II) complexes, Δ‐[Ru(bpy)₂(dmppd)]²⁺ and Λ‐[Ru(bpy)₂(dmppd)]²⁺ (dmppd = 10,12‐dimethylpteridino[6,7‐f] [1,10]phenanthroline‐11,13(10H,12H)‐dione, bpy = 2,2′‐bipyridine), were synthesized and characterized by elemental analysis, ¹H‐NMR and ES‐MS. The DNA‐binding behaviors of both complexes were studied by UV/VIS absorption titration, competitive binding experiments, viscosity measurements, thermal DNA denaturation, and circular‐dichroism spectra. The results indicate that both chiral complexes bind to calf‐thymus DNA in an intercalative mode, and the Δ enantiomer shows larger DNA affinity than the Λ enantiomer does. Theoretical‐calculation studies for the DNA‐binding behaviors of these complexes were carried out by the density‐functional‐theory method. The mechanism involved in the regulating and controlling of the DNA‐binding abilities of the complexes was further explored by the comparative studies of [Ru(bpy)₂(dmppd)]²⁺ and of its parent complex [Ru(bpy)₂(ppd)]²⁺ (ppd = pteridino[6,7‐f] [1,10]phenanthroline‐11,13 (10H,12H)‐dione).     

Ruthenium Complex “Light Switches” that are Selective for Different G‐Quadruplex Structures

Recognition and regulation of G‐quadruplex nucleic acid structures is an important goal for the development of chemical tools and medicinal agents. The addition of a bromo‐substituent to the dipyridylphenazine (dppz) ligands in the photophysical “light switch”, [Ru(bpy)₂dppz]²⁺, and the photochemical “light switch”, [Ru(bpy)₂dmdppz]²⁺, creates compounds with increased selectivity for an intermolecular parallel G‐quadruplex and the mixed‐hybrid G‐quadruplex, respectively. When [Ru(bpy)₂dppz‐Br]²⁺ and [Ru(bpy)₂dmdppz‐Br]²⁺ are incubated with the G‐quadruplexes, they have a stabilizing effect on the DNA structures. Activation of [Ru(bpy)₂dmdppz‐Br]²⁺ with light results in covalent adduct formation with the DNA. These complexes demonstrate that subtle chemical modifications of Ru^II complexes can alter G‐quadruplex selectivity, and could be useful for the rational design of in vivo G‐quadruplex probes.     

Three Bis‐BODIPY Analogous Diruthenium Redox Series: Characterization and Electronic Structure Analysis

The dianion derived from (2Z,6Z)‐3,7‐diphenyl‐N2,N6‐di(pyridin‐2‐yl)pyrrolo[2,3‐f]indole‐2,6(1H,5H)‐diimine (H₂BL), a modified BODIPY ligand precursor, is shown to be capable of bridging two metal complex fragments RuL₂, L=2,4‐pentanedionato (acac^?), 2,2’‐bipyridine (bpy) or 2‐phenylazopyridine (pap) in [Ru(acac)₂Ru(μ‐BL)Ru(acac)₂] ( 1 / 2 ), [Ru(bpy)₂Ru(μ‐BL)Ru(bpy)₂](ClO₄)₂ ([ 3 ](ClO₄)₂) and [Ru(pap)₂Ru(μ‐BL)Ru(pap)₂](ClO₄)₂ ([ 4 ](ClO₄)₂). The compounds, including a diastereoisomeric pair 1 (meso) and 2 (rac) were spectroscopically and structurally characterized. Reversible electron transfers as revealed by cyclic and differential pulse voltammetry allowed for an EPR and UV‐vis‐NIR spectroelectrochemical investigation of several neighboring charge states. Together with susceptibility measurements and TD‐DFT calculations the assignment of oxidation states reveals that 1 , 2 are diruthenium(III) species which can be oxidized or reduced by one electron whereas 3 ²⁺ and 4 ²⁺ contain ruthenium(II) and get reduced or oxidized mainly at the dianionic bridge ( 3 ²⁺) or are reduced at the ancillary ligands pap ( 4 ²⁺).     

Construction and Characterization of Ru(II)Tris(bipyridine)‐Based Silica Thin Film Electrochemiluminescent Sensors

Ru(II) tris‐bipyridine based ECL sensors were produced by embedding the complex inside silica glass thin films deposited via a sol‐gel dipping procedure on K‐glass conducing substrates. Films were prepared starting from a pre‐hydrolyzed ethanolic solution of Si(OC₂H₅)₄ and Ru(bpy)₃Cl₂. Transparent, crack‐free and homogeneous reddish silica layers, having a thickness of 200±20 nm, were obtained. The films, either deposited at room temperature or thermally annealed at 100, 200 and 300 °C for 30 h, were structurally and chemically characterized. Ru(bpy)₃Cl₂ thermal stability was previously checked by thermogravimetric analysis (TGA). The films were investigated by X‐Ray photoelectron spectroscopy (XPS), secondary ion mass spectrometry (SIMS) and UV‐vis spectroscopy. XPS in‐depth profiles revealed a homogeneous distribution of the ruthenium complex inside the silica thin layers. SIMS data suggested that the embedded Ru(bpy)₃Cl₂ did not react with oxygen inside the oxygen‐rich silica matrix to give Ru‐O bonds. Electrochemical and ECL characterization of the thin film electrodes were made by means of cyclic voltammetry (CV) and controlled potential step experiments. The ECL sensor showed a diffusive redox behavior of the Ru(bpy)₃²⁺/Ru(bpy)₃³⁺ system. Light emission produced from the reaction between oxalic acid and the electrogenerated Ru(bpy)₃³⁺ was larger and stable when thermally treated electrodes were used after a suitable hydration period. The 300 °C treated sample was the best performing sensor both in terms of low complex leakage and sensitivity. Calibration plots relative to oxalic acid were obtained both in stationary and in flowing solutions in the concentration range 2×10^?6?3×10^?4 M. A linear behavior appeared in the former case, while in the latter a slight curvature was evident as a consequence of a finite diffusion time of the analyte inside the thin film. The signal repeatability, obtained by multiple 100 μL of 10^?5 M oxalic acid injections in flowing solutions, was better than 4%. The obtained detection limit (computed as three times the standard deviation of the base‐line noise) was 10^?6 M as oxalic acid.     

DNA intercalating studies of [Ru(bpy)<Subscript>2</Subscript>HPIP]<Superscript>2+</Superscript> with intramolecular hydrogen bond ligand based on introduction of copper ion

The effects of copper ion on the interaction of [Ru(bpy)₂HPIP]²⁺(bpy = 2,2′-bipyridine, HPIP = 2-(2-hydroxyphenyl) imidazo [4,5-f] [1, 10] phenanthroline) with DNA have been investigated by electronic absorption spectroscopy and fluorescence spectroscopy. HPIP ligand of the complex with an intramolecular hydrogen bond can bind Cu²⁺ in the absence of DNA, as revealed by the absorbance and fluorescence decrease for [Ru(bpy)₂HPIP]²⁺. The resultant heterometallic complex binds to DNA via intercalation of HPIP into the DNA base pairs and its DNA-binding ability is stronger than [Ru(bpy)₂HPIP]²⁺ itself. The DNA bound [Ru(bpy)₂HPIP]²⁺ cannot bind Cu²⁺ at low Cu²⁺ concentration and the intramolecular hydrogen bond in HPIP is located inside the DNA helix. While the Cu²⁺ concentration is relative high, Cu²⁺ can quench the fluorescence of DNA bound [Ru(bpy)₂HPIP]²⁺. The quenching reason is proposed.     

Luminescence properties of [Ru(bpy)2MDHIP]2+ modulated by the introduction of DNA,copper(II) ion and EDTA

The luminescence properties of [Ru(bpy)₂MDHIP]²⁺ (bpy = 2,2′-bipyridine, MDHIP = 2,4-dihydrophenyl-imidazo[4,5-f][1,10]phenanthroline) in the absence and presence of DNA modulated by the introduction of Cu²⁺ ion and EDTA have been investigated. It is found that the ruthenium(II) complex can insert and stack between the base pairs of calf thymus DNA with MDHIP ligand, and the intramolecular hydrogen bond is located inside of the DNA. The presence of DNA can enhance the luminescence intensities of [Ru(bpy)₂MDHIP]²⁺ both in buffer solution and on an ITO surface. Moreover, the luminescence intensities of [Ru(bpy)₂MDHIP]²⁺ and DNA-bound [Ru(bpy)₂MDHIP]²⁺ are quenched by Cu²⁺, and next recovered by the addition of EDTA. The repetitive luminescence-modulations have been achieved through the introduction of equimolar Cu²⁺ and EDTA, respectively. In addition, it becomes evident that the number of luminescence-modulation cycles for [Ru(bpy)₂MDHIP]²⁺ in the absence and presence of DNA is influenced by the cumulative concentrations of CuEDTA, generated successively by the strong coordination of Cu²⁺ to EDTA.     

Catalysis of Mononuclear Aquaruthenium Complexes in Oxygen Evolution from Water: A New Radical Coupling Path using Hydroxocerium(IV) Species

The mechanism of O₂ evolution from water catalyzed by a series of mononuclear aquaruthenium complexes, [Ru(terpy)(bpy)(OH₂)]²⁺, [Ru(tmtacn)(R₂bpy)(OH₂)]²⁺ (R=H, Me, and OMe; R₂bpy=4,4′‐disubstituted‐2,2′‐bipyridines), and [Ru(tpzm)(R₂bpy)(OH₂)]²⁺ (R=H, Me, and OMe), is investigated, where terpy=2,2′:6′,2′′‐terpyridine, bpy=2,2′‐bipyridine, tmtacn=1,4,7‐trimethyl‐1,4,7‐triazacyclononane, and tpzm=tris(1‐pyrazolyl)methane. The kinetics of O₂ evolution is investigated as a function of either the catalyst concentration or the oxidant concentration by employing Ce(NH₄)₂(NO₃)₆ as an oxidant; these catalysts can be classified into two groups that have different rate laws for O₂ evolution. In one class, the rate of O₂ evolution is linear to both the catalyst and Ce⁴⁺ concentrations, as briefly reported for [Ru(terpy)(bpy)(OH₂)]²⁺ (S. Masaoka, K. Sakai, Chem. Lett. 2009 , 38, 182). For the other class, [Ru(tmtacn)(R₂bpy)(OH₂)]²⁺, the rate of O₂ evolution is quadratic to the catalyst concentration and independent of the Ce⁴⁺ concentration. Moreover, the singlet biradical character of the hydroxocerium(IV) ion was realized by experimental and DFT investigations. These results indicate that the radical coupling between the oxygen atoms of a Ru^V?O species and a hydroxocerium(IV) ion is the key step for the catalysis of [Ru(terpy)(bpy)(OH₂)]²⁺ and [Ru(tpzm)(R₂bpy)(OH₂)]²⁺, while the well‐known oxo‐oxo radical coupling among two Ru^V?O species proceeds in the catalysis of [Ru(tmtacn)(R₂bpy)(OH₂)]²⁺. This is the first report demonstrating that the radical character provided by the hydroxocerium(IV) ion plays a crucial role in the catalysis of such ruthenium complexes in the evolution of O₂ from water.     

[Ru(bpy)2(dcbpy)NHS] Labeling/Aptamer‐Based Biosensor for the Detection of Lysozyme by Increasing Sensitivity with Gold Nanoparticle Amplification

A novel [Ru(bpy)₂(dcbpy)NHS] labeling/aptamer‐based biosensor combined with gold nanoparticle amplification for the determination of lysozyme with an electrochemiluminescence (ECL) method is presented. In this work, an aptamer, an ECL probe, gold nanoparticle amplification, and competition assay are the main protocols employed in ECL detection. With all the protocols used, an original biosensor coupled with an aptamer and [Ru(bpy)₂(dcbpy)NHS] has been prepared. Its high selectivity and sensitivity are the main advantages over other traditional [Ru(bpy)₃]²⁺ biosensors. The electrochemical impedance spectroscopy (EIS) and atomic force microscopy (AFM) characterization illustrate that this biosensor is fabricated successfully. Finally, the biosensor was applied to a displacement assay in different concentrations of lysozyme solution, and an ultrasensitive ECL signal was obtained. The ECL intensity decreased proportionally to the lysozyme concentration over the range 1.0×10^?13–1.0×10^?8 mol L^?1 with a detection limit of 1.0×10^?13 mol L^?1. This strategy for the aptasensor opens a rapid, selective, and sensitive route for the detection of lysozyme and potentially other proteins.     

Binuclear 1,2,4,5-tetraimino-3,6-diketocyclohexane bis[bis(bipyridine)ruthenium(II)] redox series

The reaction of the [Ru(bpy)2(MeOH)2]2+ cation (bpy = 2,2'-bipyridine) with 1,2,4,5-tetraaminobenzene in the presence of trace water and oxygen yields the cation [(bpy)2Ru(1,2,4,5-tetraimino-3,5-diketocyclohexane)Ru(bpy)2]4+. This binuclear species undergoes ligand-based reductions, giving the 3+ and 2+ charged species. The X-ray structure, electrochemistry, ZINDO calculations, and NMR, ESR, UV/vis, and IR spectra were analyzed where possible, giving an electronic model of the binuclear species and some of its redox products. The X-ray structure reveals the [(bpy)2Ru] fragments symmetrically disposed across the 1,2,4,5-tetraimino-3,5-diketocyclohexane bridge in a molecule with Cs symmetry.     

Ru(bpy) 3 2+ sensitized photopolymerization ofN,N′-methylene-bisacrylamide

Photochemical polymerization ofN,N′-methylenebisacrylamide (MBA) initiated by the dye-reducing agent rhodamine-B-allylthiourea (ATU) system is enhanced by the addition of small amounts oftris(2,2′-bipyridine)-ruthenium(II), Ru(bpy) ₃ ²⁺ , a result attributed to the efficient formation of chain-initiating allylthiourea radicals in the presence of Ru(bpy) ₃ ²⁺ ions. The rate of polymerization was found to be proportional to [Ru(bpy) ₃ ²⁺ ]^0.5, [rhodamine-B]^0.5, [ATU]^0.5 and [MBA]^1.0. A probable mechanism consistent with the observed results is proposed and discussed. TMC 2391     

Ruthenium(II) complexes of 2-phenylimidazo[4,5-f] [1,10]phenanthroline. Synthesis,characterization and third order nonlinear optical properties

Three Ru^II complexes [Ru(bpy)₂(PIP)]²⁺, [Ru(PIP)₂(bpy)]²⁺ and [Ru(PIP)₃]²⁺ (PIP = 2-phenylimidazo[4,5-f][1,10]phenanthroline, bpy = 2,2-bipyridine) were prepared and characterized by electrospray mass spectrometry, ¹H-n.m.r, u.v.–vis. and electrochemistry. The nonlinear optical properties (NLO) of the Ru^II complexes were investigated by Z-scan techniques with 12 ns laser pulses at 540 nm, and all of them exhibit both NLO absorption and self-defocusing effects. The corresponding effective NLO susceptibility |³| of the complexes is in the (4.15 – 4.86) × 10^–12 e.s.u. range.     

Application of a Structure/Oxidation‐State Correlation to Complexes of Bridging Azo Ligands

Based on data from more than 40 crystal structures of metal complexes with azo‐based bridging ligands (2,2′‐azobispyridine, 2,2′‐azobis(5‐chloropyrimidine), azodicarbonyl derivatives), a correlation between the N? N bond lengths (d_NN) and the oxidation state of the ligand (neutral, neutral/back‐donating, radical‐anionic, dianionic) was derived. This correlation was applied to the analysis of four ruthenium compounds of 2,2′‐azobispyridine (abpy), that is, the new asymmetrical rac‐[(acac)₂Ru1(μ‐abpy)Ru2(bpy)₂](ClO₄)₂ ([ 1 ](ClO₄)₂), [Ru(acac)₂(abpy)] ( 2 ), [Ru(bpy)₂(abpy)](ClO₄)₂ ([ 3 ](ClO₄)₂), and meso‐[(bpy)₂Ru(μ‐abpy)Ru(bpy)₂](ClO₄)₃ ([ 4 ](ClO₄)₃; acac^?=2,4‐pentanedionato, bpy=2,2′‐bipyridine). In agreement with DFT calculations, both mononuclear species 2 and 3 ²⁺ can be described as ruthenium(II) complexes of unreduced abpy⁰, with 1.295(5)<d_NN<1.320(3) Å, thereby exhibiting effects from π back‐donation. However, the abpy ligand in both the asymmetrical diamagnetic compound 1 ²⁺ (d_NN=1.374(6) Å) and the symmetrical compound 4 ³⁺ (d_NN=1.360(7), 1.368(8) Å) must be formulated as abpy^.?. Remarkably, the addition of [Ru^II(bpy)₂]²⁺ to mononuclear [Ru^II(acac)₂(abpy⁰)] induces intracomplex electron‐transfer under participation of the noninnocent abpy bridge to yield rac‐[(acac)₂Ru1^III(μ‐abpy^.?)Ru2^II(bpy)₂]²⁺ ( 1 ²⁺) with strong antiferromagnetic coupling between abpy^.? and Ru^III (DFT (B3LYP/LANL2DZ/6‐31G*)‐calculated triplet–singlet energy separation E_S=1?E_S=0=11739 cm^?1). Stepwise one‐electron transfer was studied for compound 1 ⁿ, n=1?, 0, 1+, 2+, 3+, by UV/Vis/NIR spectroelectrochemistry, EPR spectroscopy, and by DFT calculations. Whereas the first oxidation of compound 1 ²⁺ was found to mainly involve the central ligand to produce an (abpy⁰)‐bridged Class I mixed‐valent Ru1^IIIRu2^II species, the first reduction of compound 1 ²⁺ affected both the bridge and Ru1 atom to form a radical complex ( 1 ⁺), with considerable metal participation in the spin‐distribution. Further reduction moves the spin towards the {Ru2(bpy)₂} entity.     

Facile design of poly(3,4-ethylenedioxythiophene)-tris(2,2′-bipyridine)ruthenium (II) composite film suitable for a three-dimensional light-harvesting system

It has been confirmed that octasulfonatocalix[8]arene (Calx-S8) and tris(2,2′-bipyridine)ruthenium (II) (Ru(bpy)₃²⁺) can form a stable host-guest complex in aqueous solution. The binding constant for 1:1 [Calx-S8⁸⁻·Ru(bpy)₃²⁺]⁶⁻ complex formation was estimated to be (2.4±0.8)×10⁴ dm³ mol⁻¹ by fluorescence titration, which indicates that the [Calx-S8⁸⁻·Ru(bpy)₃²⁺]⁶⁻ complex is the main species in 1:1 molar ratio aqueous solution of Calx-S8 and Ru(bpy)₃²⁺. In situ UV-Vis spectroscopic measurements indicated that Ru(bpy)₃²⁺ complexes can be readily deposited onto ITO electrode through electrochemical polymerization of 3,4-ethylenedioxythiophene (EDOT) using [Calx-S8⁸⁻·Ru(bpy)₃²⁺]⁶⁻ host-guest complex as a dopant anion owing to the electrostatic interaction between the cationic conductive polymer and the anionic host-guest complex. The loading degree of the composite film with Ru(bpy)₃²⁺ can be determined by Lambert-Beer law modified for the two-dimensional concentration. The obtained composite film showed good photoelectric conversion properties in response to visible light irradiation. This is a novel photocurrent generation system in which the photoexcited state energy is efficiently collected by the conductive polymeric layer.     

Synthesis, characterization and photophysics of alkyne bridged bimetallic rhenium(I) and ruthenium(II) complexes

Six new homobimetallic and heterobimetallic complexes of rhenium(I) and ruthenium(II) bridged by ethynylene spacer [(CO)₃(bpy)Re(BL)Re(bpy)(CO)₃]²⁺ [Cl(bpy)₂Ru(BL)Ru(bpy)₂Cl]²⁺ and [(CO)₃(bpy)Re(BL)Ru(bpy)₂Cl]²⁺ (bpy = 2,2′-bipyridine, BL = 1,2-bis(4-pyridyl)acetylene (bpa) and 1,4-bis(4-pyridyl)butadiyne (bpb) are synthesized and characterized. The electrochemical and photophysical properties of all the complexes show a weak interaction between two metal centers in heterobimetallic complexes. The excited state lifetime of the complexes is increased upon introduction of ethynylene spacer and the transient spectra show that this is due to delocalization of electron in the bridging ligand. Also, intramolecular energy transfer from *Re(I) to Ru(II) in Re–Ru heterobimetallic complexes occurs with a rate constant 4 × 10⁷ s⁻¹.