水性聚氨酯乳化过程中相转变的研究

本文合成了单官能团小分子物质封端的脂肪族水性聚氨酯预聚物 ,通过考察预聚物加水乳化过程中粘度及电导率的变化 ,研究了其相转变行为 .实验结果表明 ,随着软段分子量升高 ,体系的相转变点后延 ;聚酯体系的相转变比聚醚体系的相转变发生得早 ;[NCO]/ [OH]值越接近 1,体系的粘度就越高 ,相转变发生所需的水含量也越高 ;羧基含量及中和度也会对分散体系的相转变产生影响 .通过选择合适的条件 ,可以实现对乳化过程的优化     

含三苯基乙基苯氧基聚氧乙烯醚甲基丙烯酸酯功能单体的缔合型乳液增稠剂的制备及增稠机理

采用半连续法乳液聚合以甲基丙烯酸、丙烯酸乙酯、邻苯二甲酸二烯丙酯和不同量的功能单体三苯基乙基苯氧基聚氧乙烯醚甲基丙烯酸酯(SEM-25)为原料合成了疏水改性碱溶性增稠剂乳液. 测定了增稠剂乳液的粘度、透光率、pH、粒径及其分布, 结果表明随着pH值的增加, 乳液的粘度和透光率首先迅速升高, 然后缓慢下降. 随着SEM-25用量的增加, 乳胶粒的粒径先增大后减小. 与不含SEM-25的乳液增稠剂相比较, SEM-25低含量增稠剂的增稠效果和抗剪切性没有提高, 只有当SEM-25用量提高至单体质量的12%, 且乳液固含量大于0.65%时, 所制备缔合型增稠剂乳液的粘度和流变性比不含SEM-25的增稠剂才有明显提高. 在此基础上研究了增稠剂对苯丙乳液的增稠性. 含有增稠剂的苯丙乳液的粘度和透光率随pH值的变化与纯增稠剂乳液的变化类似. 只有当加入0.34 wt%苯丙乳液固体质量的增稠剂, 并且增稠剂中SEM-25含量达到5 wt%时苯丙乳液的粘度与使用不含SEM-25的增稠剂增稠的粘度相比才有明显增高. 在此基础上对增稠剂的增稠机理进行了探讨.     

聚硅氧烷聚脲嵌段共聚物的TEM及SAXS研究

采用透射电子显微镜与小角X光散射分别研究了不同软、硬段分子量及软段极性对聚硅氧烷聚脲多嵌段共聚体系微相结构的影响。结果表明,增加软段分子量及硬段含量有利于聚硅氧烷与聚脲的相分离。将极性氰丙基引入聚硅氧烷后两相混合度明显改善,同时聚脲硬段粒径减小并趋于均一。在聚氰丙基甲基硅氧烷基体中增加聚脲含量及其分子量,则两相界面厚度也随之增大。     

N,O-羧甲基壳聚糖的合成和性质研究

采用多段升温法将壳聚糖改性,合成了取代度为1.84、平均分子量为3.08×105、等电点为7.28的N,O-羧甲基壳聚糖(CMC),分别用紫外光谱、红外光谱、荧光光谱对其结构进行了表征,并对其水溶液的Zeta电位、电导率、表面张力以及水分散体系中羧甲基壳聚糖微粒的粒径分布进行了研究.结果表明, N,O-羧甲基壳聚糖具有表面活性;介质的pH值和浓度对羧甲基壳聚糖溶液的稳定性有很大的影响.     

含二十二烷基聚氧乙烯醚甲基丙烯酸酯功能单体的缔合型乳液增稠剂的制备及表征

以甲基丙烯酸、丙烯酸乙酯、邻苯二甲酸二烯丙酯和不同量的功能单体二十二烷基聚氧乙烯醚甲基丙烯酸酯(BEM)为原料,采用半连续乳液聚合方法合成了疏水改性碱溶性缔合型增稠剂乳液.测定了增稠剂乳液的粘度、透光率、乳胶粒粒径及其分布等性能,考察了不同固含量下乳液粘度和透光率随pH的变化情况.结果表明随着BEM用量的增加,乳胶粒粒径逐渐增大.随着pH值的增加,乳液的粘度首先迅速升高,然后缓慢下降.与不含BEM的增稠剂乳液相比,当乳液固含量大于0.5%,BEM含量占单体量低于5.0wt%时,该缔合型增稠剂的增稠效果和抗剪切性有显著提高,BEM含量较高(8.0wt%或更高)时反而使增稠效果和抗剪切性变差.在此基础上研究了增稠剂对苯丙乳液的增稠效应,结果显示BEM含量占单体量的2.5wt%时,对苯丙乳液的增稠作用最好.与使用功能单体三苯乙基苯酚聚氧乙烯醚甲基丙烯酸酯改性的增稠剂相比,含BEM的增稠剂在BEM用量较少的情况下就能起到明显的增稠效果.     

羧甲基纤维素钠/蒙脱土悬浮体系的流变性能及其影响因素

考察了蒙脱土(MT)质量分数(w)、羧甲基纤维素钠(CMC)/MT质量比(R)、电解质(NaCl、MgCl2和AlCl3)、pH值和温度对MT或CMC/MT悬浮体系流变性能和触变性的影响。 结果表明,随w增加,纯MT悬浮体系的流体类型由近牛顿流体向塑型流体变化,触变类型则由无触变、正触变向复合触变性转变;而CMC/MT悬浮体系仍保持MT体系的正触变塑型流体特征,但屈服值τ0和稠度指数K增加,滞后环面积S和电动电势|ζ|先增加后减小,表现出同步变化。 电解质和实验温度均不改变CMC/MT悬浮体系的正触变性塑型流体特征,但电解质使τ0和K增加,而温度增加使τ0和K减小。 随介质pH值的增加,CMC/MT体系由负触变性变为正触变性,|ζ|增大,S先增加后减小,且在pH=8.46时达到最大。     

阳离子型自乳化端羟基硅油/聚氨酯微乳液的形态及流变性能

在催化剂和少量助溶剂的作用下,以端羟基硅油(HPMS)/聚(四亚甲基醚)二醇(PTMG)为软段,异佛尔酮二异氰酸酯(IPDI)为硬段单体,以三羟甲基丙烷TMP为交联剂、N-甲基二乙醇胺(MDEA)为扩链剂合成了一系列自乳化双软段HPMS/PU微乳液.分析了HPMS用量对HPMS/PU微乳液粒径及微观形态的影响;研究了HPMS/PU中HPMS含量、MDEA用量、TMP用量、预聚体分子量对其流变性能的影响.研究结果表明,HPMS的加入使乳液粒径增加,HPMS/PU乳液为非牛顿流体,且具有一定的假塑性和触变性,表观粘度随切变速率的变化规律呈现一定的切力变稀特征,流动指数范围为0.885~0.531之间;其零剪切粘度值为13.59~25.08mPa.s,随HPMS用量、MDEA用量、预聚体相对分子质量、TMP用量而异.     

甲基丙烯酸对聚合物乳胶粉再分散性影响机理

采用半连续种子乳液聚合法,以甲基丙烯酸(MAA)为壳层亲水功能单体,合成了丙烯酸酯原乳液,并通过喷雾干燥法制得具有可再分散性的聚合物乳胶粉.讨论了原乳液粒子粒径随pH值和MAA量的变化关系;重点研究了MAA量对乳胶粉水分散液稳定性、再分散乳液zeta电位、乳胶粒粒径分布及乳胶粉内部微观形貌的影响,并分析其作用机理.研究结果表明:原乳液粒子粒径随pH值的增大逐渐增大,且MAA含量越高,粒径增幅越大;随MAA量增加,再分散液稳定性增强,zeta电位绝对值增大,平均粒径逐渐变小,乳胶粉再分散性显著改善.透射电子显微镜(TEM)结果显示:当MAA含量较高时,乳胶粉内部出现较大孔径的中空微孔结构.中空微孔结构提供水分向乳胶粉内部扩散通道,因而优化其水分散性,再分散乳液的"绒毛结构"与较高的zeta电位赋予其优异的分散稳定性.     

水性聚氨酯甲阶酚醛水分散液微观形态及杂化膜的性能

以自乳化型聚氨酯和甲阶酚醛制备了聚氨酯 酚醛复合水分散液 .pH值与酚醛溶解度的关系表明甲阶酚醛的溶解是酚羟基电离的结果 .聚氨酯 甲阶酚醛水分散液粒子的形态有核壳结构、不完善的核壳结构及纯聚氨酯颗粒三种 ,后者粒径最小 .随着酚醛用量的增大 ,粒子平均粒径增大 .酚醛含量增加使体系热稳定性、机械稳定性、冻融稳定性及临界聚沉值下降 ,pH值稳定范围变窄 .分散液稳定性和电性能考察证明 ,本复合分散液的稳定性主要由分散液的电性能所决定 ,属真溶胶 ,但在一定程度上也具有大分子溶液的特性 .复合液涂膜的性能较纯聚氨酯有所改善 ,尤其在添加了硅溶胶之后     

脂肪族水性聚氨酯的动态力学行为研究

合成了一系列脂肪族水性聚氨酯 .考察了软段的组成、软段分子量及DMPA用量对产物动态力学性能的影响作用 .实验结果表明 ,软段的化学结构对水性聚氨酯的相态结构影响很大 .聚醚型水性聚氨酯具有较低的软段玻璃化转变温度 (Tgs) .聚醚型产物的微相分离程度高于聚酯型产物 .当采用聚酯和聚醚二元醇为混合软段时 ,Tgs随软段中聚醚含量的提高而逐渐降低 .提高DMPA用量 ,软段玻璃化转变温度Tgs移向低温区 ,硬段玻璃化转变温度Tgh移向高温区 ,说明体系的微相分离程度加大 .当软段分子量较低时 ,产物为半相容结构 ,只有一个主转变峰 ,软段的玻璃化转变以肩峰的形式出现 ;当软段分子量较高时 ,产物的微相分离程度较高 ,可以分别观察到软段及硬段的玻璃化转变 .总之 ,通过改变软段的种类、组成和分子量以及DMPA用量 ,可以大幅度地改变水性聚氨酯的形态结构 .     

Preparation and characterization of waterborne polyurethanes modified with bis(3-(1-methoxy-2-hydroxypropoxy) propyl) terminated polysiloxanes

Polyurethanes(PU) were prepared using toluene diisocyanate,polypropylene glycol,ethylene glycol, dimethylolpropionic acid and triethylamine,and a siloxane modified PU(PSU) was obtained through reaction of the PU prepolymers with bis(3-(1-methoxy-2-hydroxypropoxy)propyl) terminated polysiloxanes(PMTS) of different molecular weight,specifically designed for this purpose.Results showed that,with increases in molecular weight of PMTS and its content,viscosity of the final PSU latexes decreased;phase separation of the incorporated PMTS in PSU films increased;the average particle sizes of the latexes varied between 110 nm and 330 nm,and the surface tension in the final latexes was relatively constant regardless of PMTS amount and its molecular weight.It was likely that copolymerized polysiloxanes had trend to enrich on top of the film when PMTS molecular weight was around 2000 and its content above 5 wt%.In general, PMTS modified polyurethane films showed higher performance than those from unmodified waterborne polyurethane latexes.     

Potentiometric and viscometric study of the alkalization of latex dispersions of ethyl acrylate — methacrylic acid copolymers in the presence of salt

The behavior of latices of ethyl acrylate — methacrylic acid copolymers during alkalization was investigated using potentiometric titration and viscometry. In the presence of NaCl in dispersion medium pH and viscosity were lower compared to salt-free dispersions. Due to strong electrostatic interactions at low salt concentration the apparent dissociation constant of the carboxylic groups is small and the polymer segments bearing these groups are in extended conformations. The screening effect at higher salt concentration increases the apparent dissociation constant and decreases the extension of the polymer segments. The pH and viscosity of latex dispersions alkalized in the presence of salt are thus smaller.     

Hydrolytic stability of nano-particle polyurethane dispersions: Implications to their long-term use

Nano-particle segmented polyurethane anionomer dispersions with ions either on the soft segment or on the hard segment were synthesised using 2,2-bis(hydroxymethyl) propionic acid and 5-sodiosulfo-1,3-benzenedicarboxylic acid as ionic centre. The resulting polyurethane dispersions were characterized for their particle size, reduced viscosity and hydrolytic stability in the presence of the aqueous phase during storage. At similar ionic contents, the polyurethanes that contain ionic groups on their soft segment had smaller particle sizes than those that contain ionic groups on the hard segment due to the effectiveness of the sulphonate ionic groups incorporated in the former. The reduced viscosity of the anionomers in dimethylformamide (DMF) showed typical polyelectrolyte effect that can be eliminated by the addition of LiBr. The hydrolysis study conducted over 2-years indicated that polyurethanes in which the ions were located on the hard segment had better hydrolytic stability in aqueous environment than those with ions located on the soft segment. We attributed this due to the fact that unsolvated hydrophobic polyester segments were packed in the interior of the particles while the strongly hydrated urethane segments with mutually repelling carboxylate ions were situated on the outside surface of the particles. The polyester groups prone to hydrolytic attack were thus protected against hydrolysis as effectively as in the dry solid form.     

交联密度对脂肪族聚氨酯弹性体结构与性能的影响

采用异佛尔酮二异氰酸酯(IPDI)与聚醚二元醇、三羟甲基丙烷(TMP)和1,4-丁二醇反应制备了具有不同交联密度的脂肪族聚氨酯弹性体.研究结果表明,当聚氨酯弹性体的硬段含量为40 wt%时,随着TMP含量的增加,聚氨酯弹性体的交联密度线性增加.随着聚氨酯弹性体交联密度的提高,聚氨酯中硬段相的玻璃化转变温度由32℃降为2...     

侧链为光敏感基团的可生物降解聚氨酯的合成及表征

设计合成2-甲基-2-肉桂酰氧甲基-1,3-丙二醇(MCO)作为扩链剂,并以聚乳酸二醇(PLA diol)为软段,异佛尔酮二异氰酸酯(IPDI)和MCO为硬段制备了一系列侧链含有肉桂基团的可生物降解聚氨酯.结果表明MCO具有较高的反应活性,可满足制备高分子量聚氨酯的要求.聚氨酯结构中的肉桂双键可在紫外光和光引发剂的共同作用下,发生快速的交联反应,短时间内形成交联结构.软段结构相同时,凝胶含量随MCO含量的增加而增加.硬段结构相同时,凝胶含量随软段分子量的增加而减少.适度的交联可提高拉伸强度和形变回复率.     

Segmented polyurethanes derived from novel siloxane–carbonate soft segments for biomedical applications

A novel macrodiol based on mixed silicone and carbonate chemistries was synthesized and used as a soft segment precursor in the synthesis of two series of segmented polyurethane (PU) copolymers varying in hard segment content and soft segment molecular weight. The hard segments in these copolymers were derived from 4,4‐methylene diphenyl diisocyanate and 1,4‐butane diol. The phase transitions, microphase separation behavior, and mechanical properties of the copolymers were investigated using a variety of experimental methods. When compared with segmented PU copolymers having predominately poly(dimethyl siloxane) soft segments, these siloxane–carbonate soft segment copolymers exhibit enhanced intersegment mixing, and consequently relatively low mechanical modulus. With relatively low modulus and siloxane units in the soft phase, the siloxane–carbonate PUs have potential for use in cardiac and orthopedic biomedical applications. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2011     

UV curable waterborne polyurethane acrylate dispersions based on hyperbranched aliphatic polyester: effect of molecular structure on physical and thermal properties

A novel waterborne hyperbranched polyurethane acrylate for aqueous dispersions (WHPUDs) based on hydroxy‐functionalized hyperbranched aliphatic polyester Boltorn? H20 was investigated. The effects of structural composition and crosslinking density have been studied in terms of swellability by water, thermal degradation, viscosity changes as well as transmission electron microscopy (TEM) morphology. The swell ratio showed an increasing trend with the higher concentration of ionic group, which is due to the increased total surface area of particles. The results of thermogravimetric analysis (TGA) for cured WHPUD films indicated good thermal stability with no appreciable weight loss until 200°C. The activation energies were evaluated and were found in the range 154–186 kJ mol^?1. It was observed that an increase in hard segment content provoked the increases in thermal degradation temperature and activation energy of waterborne dispersions. The transmission electron photographs revealed that the average particle sizes of aqueous dispersions were in the range 30–125 nm. Owing to the enlargement of the stabilization site, the particle size decreased as the content of carboxyl group and degree of neutralization increased. The viscosity of WHPUDs increased rapidly with increasing the degree of neutralization. Moreover, water showed a favorable viscosity reduction effect. Copyright © 2004 John Wiley & Sons, Ltd.     

Study on siloxane‐modified polyurethane dispersions from various polydimethylsiloxanes

In this work, various polydimethylsiloxanes (PDMS) are incorporated with isophorone diisocyanate (IPDI), 2,2‐bis(hydroxymethyl)propionic acid (DMPA), and poly(tetramethylene oxide) (PTMO) by the prepolymer process to synthesize a series of siloxane‐modified polyurethane dispersions (PUDs) with 35 wt % solid content, viscosities of 20–100 cps, and particle sizes of 40–130 nm. Hydrophobic PDMS was introduced into the PU chain either based on random distribution or through the block segment arrangement. We also establish the composition‐property relationship of PDMS‐PUD, which includes PDMS's type and molecular weight and PDMS‐PUD film's contact angle and mechanical property. The tensile strength of PDMS‐PUD film is decreased with increasing amount of PDMS. Scanning electron microscopy for chemical element analysis indicated that PDMS migrated to the surface much more easily in the block arrangement than in the random distribution. Also, some PDMS‐PUD films show a peau‐like surface, so their PUDs are considered promising to be used in processes for textiles. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3482–3490, 2005     

The effect of attached tetracycline and hydrophilic groups on the enhancement of antibacterial effectiveness and low temperature flexibility of polyurethane

Tetracycline was chemically attached to polyurethane (PU) to enhance its antimicrobial activity, and a carboxyl group or polyol was also attached to PU to enhance the hydrophilicity. The attached groups affected cross‐linking, viscosity of PU solution, glass transition of soft segment, breaking tensile stress, reliable shape recovery capability, flexibility at very low temperature, surface hydrophilicity, and antibacterial effectiveness. The glass transition temperature could go up from ?67.5°C for unmodified PU to ?48.8°C due to the attached tetracycline. The attachment of tetracycline boosted breaking tensile stress and shape recovery by 345% and 186%, respectively, relative to unmodified PU. The attached carboxyl group and polyol improved the hydrophilicity as confirmed by water swelling and water contact angle data. Finally, PU samples with the attached tetracycline demonstrated excellent flexibility at freezing temperature compared with ordinary PU and absolutely inhibited the bacterial growth of S. aureus and K. pneumoniae on PU.