锆改性钴基费-托合成催化剂催化性能的研究

 考察了助剂锆和金属钴负载量对锆改性Co／Al2O3催化剂催化性能的影响．结果表明，锆助剂能够高度分散在氧化铝载体上，而活性组分钴以一定尺寸存在；锆的添加能够明显地提高Co／Al2O3催化剂的催化活性和C5＋烃选择性，但助剂锆含量对催化剂催化性能的影响不大；在锆存在下，催化剂的催化活性随金属钴含量先升高后降低．进一步的研究表明，催化剂上烃形成速率的提高可能是由于锆助剂能够增加催化剂的活性位数目，增强桥式CO吸附的强度，在Co－ZrO2间形成界面．     

费-托合成Co/ZrO2-Al2O3催化剂反应性能的研究

以ZrOCl2·6H2O和AlCl3为原料，采用共沉淀方法制得一系列不同ZrO2质量分数的ZrO2-Al2O3混合氧化物载体；并以该混合氧化物为载体，采用初湿浸渍法制得钴质量分数为12％的Co/ZrO2-Al2O3催化剂。XRD、NH3-TPD、TPR和原位IR等表征结果表明，随着混合载体中ZrO2质量分数的增加，载体比表面积先增加后减少，混合载体的平均孔径则小于单一氧化物ZrO2和Al2O3的平均孔径。ZrO2和Al2O3载体混合后会导致氧化物的比表面积和酸性增大并且有新的物相生成。当混合氧化物用作载体时，能够抑制载体表面金属钴的分散，改变催化剂的还原行为，降低催化剂对CO物种的吸附能力。CO加氢反应表明，与单一金属氧化物相比，钴负载ZrO2-Al2O3混合氧化物催化剂的加氢活性和重质烃选择性有所降低。     

Co/γ-Al_2O_3催化剂上肉桂醛的选择加氢──反应性能的考察

研究了γ－Al2O3负载的Co／γ－Al2O3催化剂上肉桂醛的选择加氢反应．反应结果表明,以CoCl2作为前驱物的Co／γ－Al2O3催化剂的选择性要高于以Co（NO3）2作为前驱物的Co／γ－Al2O3催化剂,而活性则正好相反．当钴的负载量小于9％时,随着钴负载量的增加,催化剂的活性和选择性随之增加,当钴的负载量大于9％时,随着钴负载量的增加,Co／γ－Al2O3催化剂的活性略有增加,而生成肉桂醇的选择性变化也很小,认为9％的钴负载量是催化剂反应活性和选择性的一个阈值．在所选定的范围内,反应温度和压力对肉桂醛加氢的选择性几乎没有影响．     

金属有机骨架材料MIL-53(Al)负载钴催化剂的CO催化氧化反应性能

采用溶剂法合成了热稳定性高的金属有机骨架材料MIL-53(Al)(MIL:Materials of Institut Lavoisier),用此材料为载体负载钴催化剂用于CO的催化氧化反应,并与Al2O3负载的钴催化剂进行了对比.采用热重-差热扫描量热(TG-DSC)、傅里叶变换红外(FTIR)光谱、X射线衍射(XRD)、N2物理吸附-脱附、透射电子显微镜(TEM)、氢气程序升温还原(H2-TPR)等方法对催化剂的结构性质进行了表征.TG和N2物理吸附-脱附结果表明,载体MIL-53(Al)有好的稳定性和高的比表面积;XRD以及TEM结果表明Co/MIL-53(Al)上负载的Co3O4颗粒粒径(平均约为5.03 nm)明显小于Al2O3上Co3O4颗粒粒径(平均约为7.83 nm).MIL-53(Al)的三维多孔结构中分布均匀的位点能很好地分散固定Co3O4颗粒,高度分散的Co3O4颗粒有利于CO的催化氧化反应.H2-TPR实验发现Co/MIL(Al)催化剂的还原温度低于Co/Al2O3催化剂的还原温度,低的还原温度表现为高的催化氧化活性.CO催化氧化结果表明,MIL-53(Al)负载钴催化剂的催化活性明显高于Al2O3负载钴催化剂,MIL-53(Al)负载钴催化剂在160°C时使CO氧化的转化率达到98%,到180°C时CO则完全转化,催化剂的结构在催化反应过程中保持稳定.     

纳米ZrO2/Al2O3复合载体及Ni/ZrO2/Al2O3催化剂的性能研究

 采用溶胶-凝胶法在经过扩孔处理的Al2O3基载体上制备了纳米ZrO2/Al2O3复合载体,并通过浸渍法制备了NiO/ZrO2/Al2O3催化剂. 用XRD,TPR,TPD和N2吸附等技术分别考察了载体和催化剂的结构及表面性能,研究了复合载体对Ni/ZrO2/Al2O3催化CO2重整CH4反应性能的影响. 结果表明,纳米ZrO2/Al2O3复合载体具有较大的比表面积、适宜的孔径分布及稳定的t-ZrO2结构,Ni/ZrO2/Al2O3催化剂具有较好的CO2重整CH4反应活性和稳定性.     

ZrO2对CuO／γ—Al2O3催化剂CO氧化性能的影响

用流动反应法、TPR、TPO和TG等技术研究了ZrO2的改性和CuO负载量对Cuo／y－Al2O3催化剂的氧化性能及还原行为的影响．实验结果表明，在低负载量（wCuO=15%以下）时，ZrO2对γ-Al2O3的改性可明显提高CuO／γ-Al2O3催化剂的CO氧化活性．ZrO2的存在可增加活性铜物种在载体表面的富集和有效地促进CU2+物种的氧化还原循环，增加CuO催化剂表面上铜物种的可还原量，从而促进CuO催化剂的氧化活性．     

Fe2O3/YSZ-γ-Al2O3催化剂在甲烷催化燃烧中的催化性能研究

以Fe2O3为活性组分，γ-Al2O3，ZrO2-γ—Al2O3及YSZ—γ—Al2O3(YSZ是用Y2O3稳定ZrO2的催化剂载体)为载体，制备了3种甲烷燃烧催化剂．其中以YSZ—γ—Al2O3为载体的催化剂催化性能最好．XPS检测发现．ZrO2和Y2O3的存在可以增加和稳定Fe2O3的表面浓度，同时也可减弱Fe2O3与γ—Al2O3之间的相互作用．Fe2O3质量分数为10％的Fe2O3／YSZ—γ—Al2O3催化剂具有最佳的催化活性．XRD测试结果表明．该催化剂的活性与Fe2O3在载体上的分散状况有关．     

不同载体Ni基催化剂生物质热解气甲烷化反应性能

采用浸渍法制备了Ni金属负载在不同载体(SiO2、ZrO2、CeO2、Al2O3和Al2O3-CeO2)表面形成的催化剂,研究了水蒸气和载体对生物质热解气甲烷化反应性能的影响。结果表明,随着水蒸气量的增加CO转化率逐渐增大,而甲烷选择性呈现先增加后降低的变化趋势,当nw ater/ngas比值为0.26时达到最大。载体Al2O3相比SiO2、ZrO2和CeO2具有更大的比表面积和Ni金属分散度,促进了生物质热解气甲烷化反应活性和选择性。相比于Ni-Al2O3催化剂,Al2O3-CeO2复合载体具有更多的镍金属负载量活性金属分散度,以及最好的低温甲烷化反应性能。在300℃的低温条件下,Ni-Al2O3-CeO2催化剂的CO转化率达到97%,CH4增长率达到110%。     

用不同前驱体制备的Co/SiO2催化剂的结构及其CO2/CH4重整反应性能

 分别采用硝酸钴、醋酸钴、硫酸钴和氯化钴为前驱体制备了Co／SiO2催化剂,用XRD,TPR,SEM和H2－TPD等实验技术考察了钴盐前驱体对催化剂结构和二氧化碳重整甲烷反应性能的影响,重点考察了硝酸钴和醋酸钴的作用．结果表明,由醋酸钴制备的Co／SiO2催化剂有最佳的催化活性和稳定性,它在钴物种的存在状态、金属－载体相互作用、钴金属晶粒度及抗烧结、抗积炭能力等方面,均与由硝酸钴制备的Co／SiO2催化剂存在显著的差别．Co／SiO2催化剂的反应活性和稳定性分别与其金属分散度和抗烧结、抗积炭能力密切相关．     

贵金属对钴基催化剂上肉桂醛选择加氢反应的影响

 研究了贵金属改性的Co／γ－Al2O3催化剂上的肉桂醛选择加氢反应．结果表明，通过Pt，Pd和Ru贵金属改性，提高了催化剂的活性，但只有Pt改性的催化剂具有较高的选择性．w（Pt）＜0．5％时，催化剂的活性随着Pt含量的增加呈直线升高，当w（Pt）＝0．5％时，催化剂活性可提高近5倍，但催化剂的选择性变化很小．XRD结果表明，催化剂经还原后，γ－Al2O3上的钴主要为α－Co0．TPR结果表明，Pt的加入提高了Co3O4的还原性能，且Pt含量越高，Co3O4的还原温度越低．XPS结果表明，Pt改性的催化剂样品，其Co3O4大部分被还原为Co0．由于Pt与Co具有协同效应，故Pt改性的Co／γ－Al2O3催化剂既具有较高的活性，又具有很高的选择性．     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

化学计量中不确定度评定研究进展

测量不确定度是表征合理地赋予被测量之值的分散性的参数。本文针对化学计量不确定度评定基础模型仅适用于线性模型、概率分布为正态分布或缩放位移t分布等局限,介绍了近年来不确定度评定的研究热点:蒙特卡罗方法(Monte Carlo Method,MCM),不确定度评定的来源、评定概念、评估方法及其发展过程,扩大了测量不确定度评定与表示的适用范围。     

微量钙的测定方法研究进展

介绍了1995-2006年期间测定微量和痕量钙的方法,如电感耦合等离子体-原子发射光谱法、原子吸收光谱法以及离子色谱法等的工作原理和特点,并说明了其测定微量钙的应用领域。并对微量钙的测定技术进行了展望(引用文献55篇)。