二氧化硅纳米粒子薄膜的制备及光学性能

以二氧化硅胶体和聚二烯丙基二甲基氯化铵(PDDA)为原料,利用静电自组装技术制备了PDDA/SiO2复合薄膜. TEM图象显示,薄膜中的SiO2纳米粒子为密堆积,薄膜均匀、致密;电子衍射实验结果显示,所组装的薄膜为非晶态膜.载玻片表面组装SiO2纳米粒子薄膜后,透射率随薄膜双层数增加呈现周期变化.薄膜具有增透作用,载玻片双面组装薄膜后在一定波长范围内的透射率可提高5％以上. PDDA/SiO2复合薄膜的光学性质主要由SiO2纳米粒子决定,每一双层的平均物理厚度小于SiO2纳米粒子的粒径,薄膜中存在层间穿插现象,逐层组装的复合薄膜具有单层光学薄膜的特性.     

静电自组装铁电超薄膜及其性能研究

利用静电自组装方法在石英玻璃表面交替沉积聚二烯丙基二甲基氯化铵(PDDA)和聚偏氟乙烯(PVDF)超薄膜,制得PDDA/PVDF铁电复合超薄膜.通过石英晶体微天平实时监测超薄膜的沉积,研究了超薄膜的表面形貌、结构及电性能.结果表明,自组装每层PVDF超薄膜的厚度为7.5 nm;PDDA/PVDF铁电复合超薄膜的表面平整、均匀,其中C1s的光电子能谱与极化处理后充负电荷的PVDF铁电聚合物一致,但F1s由于溶解再组装过程而降低了0.3 eV;静电自组装材料纳米级的薄膜厚度和聚合物的络合作用导致了铁电复合超薄膜的非晶结构和高的表面电阻率.     

石墨烯/碳纳米管复合薄膜的制备进展

石墨烯/碳纳米管复合材料具有石墨烯和碳纳米管的共同特性,它弥补了石墨烯不连续和碳纳米管网存在间隙这两方面缺点。本文探讨了石墨烯/碳纳米管复合薄膜的制备新进展,阐述了利用自组装合成、非原位合成以及非化学合成等方法制备厚度薄、强度高和比电容高等特点的石墨烯/碳纳米管复合薄膜的方法,对石墨烯/碳纳米管复合薄膜在传感器、锂电池和超级电容器等方面的应用前景进行了展望。     

自组装超薄膜修饰Ta2O5介质膜及其特性研究

采用静电自组装方法在五氧化二钽(Ta2O5)介质氧化膜上制备了聚二烯丙基二甲基氯化铵(PDDA)/聚苯乙烯磺酸钠(PSS)和聚二烯丙基二甲基氯化铵/聚-3,4-乙烯二氧噻吩-聚苯乙烯磺酸钠(PEDOT-PSS)超薄膜.研究了两种自组装超薄膜在Ta2O5介质氧化薄膜上的组装特性.结果表明两种自组装膜能够稳定地组装于Ta2O5介质膜表面,并有效降低薄膜的表面粗糙度.进一步研究了两种自组装超薄膜修饰的Ta2O5电容结构的电性能.结果表明静电自组装膜对Ta2O5介质膜表面进行修饰后,有效地隔离了介质氧化膜中的缺陷,降低了电容的漏电流并提高耐电压能力;研究还发现不同厚度的超薄膜对Ta2O5电容结构的耐压特性有不同程度的影响,较厚的薄膜可以更好地提高电容的耐压能力并降低漏电流,但会增加电容的等效串联电阻(ESR).另外,在相同薄膜层数的情况下,聚合物电解质PEDOT-PSS良好的导电性能降低了复合超薄膜的电阻,使得PDDA/PEDOT-PSS修饰的电容结构ESR值较低.     

层层自组装法制备石墨烯/聚苯胺复合薄膜及在传感器中的应用

利用层层自组装技术,将聚丙烯酸修饰的石墨烯(PAA-Gr)与聚苯胺(PANI)进行层层自组装,制备了石墨烯/聚苯胺{PAA-Gr/PANI}n复合薄膜.聚丙烯酸修饰石墨烯不仅可以提高石墨烯的分散性,而且可以使石墨烯表面带负电荷,为其与带正电的PANI进行层层自组装提供了可能.利用紫外光谱跟踪了{PAA-Gr/PANI}n复合薄膜层层自组装过程.通过红外光谱、X射线衍射、扫描电子显微镜和循环伏安等方法表征了{PAA-Gr/PANI}n复合薄膜的结构.研究了{PAA-Gr/PANI}n复合薄膜的电化学性能,并探讨了复合薄膜在过氧化氢(H2O2)传感器中的应用.{PAA-Gr/PANI}n复合薄膜对H2O2表现出良好的电催化活性,其线性检测范围为0.005~0.3 mmol/L,线性相关系数为0.99858,检测下限为1×10-6mol/L.     

盘状多酸P_5W_(30)/阳离子聚电解质/氧化石墨烯杂化多层膜的电致变色性能

为了提高薄膜[PEI/P_5W_(30)]_(30)的电致变色性能,将具有大的二维尺寸和良好导电性的氧化石墨烯引入该薄膜中。通过层层自组装(LBL)技术构筑了基于盘状多酸K12.5Nal.5[Na P_5W_(30)O_(110)]·15H_2O(P_5W_(30))、氧化石墨烯(GO)的复合薄膜[PEI/P_5W_(30)/PEI/GO]_(30)(PEI:聚乙烯亚胺),并利用UV-Vis光谱对薄膜的组成及增长进行监测;通过原子力显微镜对薄膜的表面形貌进行考察,利用循环伏安法对薄膜电化学氧化还原性质进行研究;薄膜在外加氧化还原电位下呈现出无色/蓝色的可逆变化,电致变色响应时间在10 s以内;此外,薄膜在阶跃电位0.75 V/-0.75 V下循环150次,电致变色性能没有明显减弱,体现了薄膜良好的电致变色可逆性。氧化石墨烯的引入使薄膜[PEI/P_5W_(30)/PEI/GO]_(30)呈现出响应速度快、抗电疲劳强的电致变色性能,将在电致变色器件领域有广阔的应用前景。     

富勒醇与阳离子聚电解质复合薄膜的制备与表征

采用静电自组装技术制备了富勒醇与聚对亚苯亚乙烯基 (PPV)的前驱体、聚二烯丙基二甲基氯化铵(PDDA)的复合薄膜 ,利用紫外 可见光吸收光谱 (UV Vis)、原子力显微镜 (AFM )、透射电镜 (TEM)和X射线光电子能谱 (XPS)对薄膜进行了表征 .UV Vis吸收光谱显示 ,在特定波长下自组装薄膜的吸光度与薄膜的双层数成线性关系 ,组装过程具有一致性与重复性 .AFM图象显示富勒醇组装到基片表面后形成直径为几十到10 0多nm的团簇 .富勒醇溶液过滤后组装薄膜 ,薄膜具有较好的均匀性 ;富勒醇溶液不经过滤 ,直接组装薄膜 ,将在薄膜中引入C6 0 晶粒 .XPS分析结果提示C6 0 被羟基修饰并通过静电吸引机制与阳离子聚电解质组装成膜 .富勒醇与PPV的前驱体、PDDA具有很好的自组装性能 ,膜层间的结合力较强 ,所组装的薄膜具有较高的牢固度 .     

氧化石墨烯薄膜的光电化学性质

用改进的Hummers法制备了氧化石墨烯（GO）,在质子化的氧化铟-氧化硒导电玻璃基片上制备了静电自组装薄膜,通过紫外-可见光谱和扫描电镜对薄膜进行了表征并研究了薄膜的光电化学性质.结果表明,GO薄膜是一种稳定的光电阴极材料,在光强为100 mW/cm^2的白光照射下,偏压为-0.4 V时,0.1 mol·L^-1的N...     

基于石墨烯和量子点自组装膜的能量转移构筑的高灵敏度DNA界面荧光传感

以QDs作为荧光探针, HIV1病毒序列DNA为研究对象, 设计了Quartz/PDDA/PSS/PDDA/CdTe/ssDNA自组装膜, 利用氧化石墨烯(GO)猝灭自组装膜上CdTe QDs的荧光, 而靶DNA(tDNA)与自组装膜表面ssDNA的互补配对作用使GO与CdTe QDs的距离增加, 导致自组装膜上量子点的荧光恢复, 由此建立了一种基于GO与QDs自组装膜之间荧光共振能量转移的快速灵敏检测DNA的界面分析方法, 检出限为7.26×10-14 mol/L. 本方法制备的DNA探针操作简单, 自组装膜表面修饰的ssDNA提高了方法的选择性, GO的猝灭作用降低了检测背景, 极大地提高了荧光分析方法的灵敏度.     

还原氧化石墨烯/Au复合微电极阵列的制备及光电特性

利用双光束干涉-无掩模光刻技术制备了周期性氧化石墨烯微结构阵列,利用肼蒸气对氧化石墨烯脱氧还原,然后蒸镀超薄Au薄膜制备了还原氧化石墨烯/Au复合微电极阵列(R-GO/Au).对复合电极在可见光波段的透过率和表面电阻进行了表征,结果表明,R-GO/Au复合微电极阵列具有良好的光电特性.将R-GO/Au复合微电极阵列引入到有机太阳电池中作为半透明阳极,器件的光电转化效率可达3.43%.     

石墨烯的制备、表征及其在透明导电膜中的应用

Over the past decade, graphene has been the focus of intensive research because of its remarkable physical and chemical properties. Researchers have made many efforts to synthesize graphene and investigate its potential applications. In this article, we first briefly review the fabrication processes and properties of graphene. Then, we discuss the application of graphene/Ag hybrid films as transparent conductive films (TCFs). Next, we introduce our results on this topic. Graphene and Ag nanowires were synthesized by chemical vapor deposition (CVD) and the polyol process, respectively. We successfully fabricated a graphene/Ag hybrid film with a low sheet resistance (R_s) of 26 Ω·□^-1. Finally, we describe the main challenges facing graphene hybrid films and their potential applications in a wide range of optoelectronic devices.     

Approach to excellent superhydrophobicity and corrosion resistance of carbon-based films by graphene and cobalt synergism

A new series of carbon-based films doped with graphene oxide and cobalt (G-Co/a-C:H films) were successfully prepared on Si substrate via one-step electrochemical deposition of methanol as the carbon source and graphene oxide/cobalt as the dopant. G-Co/a-C:H films were fabricated at various graphene oxide concentration for comparative experiments. It can be found that the graphene oxide and cobalt were well embedded in amorphous carbon matrix to form superhydrophobic G-Co/a-C:H film at the doping GO concentration of 0.007 mg/mL, which was confirmed by transmission electron microscopy (TEM). It was noted that the superhydrophobicity of the resulting surface derives from its rough surface with hierarchical micro-nanostructures and the presence of the low-surface-energy GO components on it. The hierarchical micro-nanostructures are attributed to the corporate joint of GO and cobalt to form the multilevel nanoscale composite interface. Specially, the as-fabricated superhydrophobic G-Co/a-C:H film could exhibit excellent self-cleaning ability and corrosion resistance, revealed by the self-cleaning and corrosion tests.     

柔性透明石墨烯膜制备及导电性能研究

本文通过液相化学还原和热还原联合作用制备了柔性透明导电石墨烯膜.阳极氧化铝(AAO)模板在制备过程中既作为抽滤的滤网,又作为热还原处理时支撑石墨烯膜的衬底,制成的柔性透明石墨烯膜对波长为540—840nm的可见光透光率为80%,面电阻为850Ω/平方,这与化学气相沉积法制备的石墨烯膜(280—770Ω/平方)相近,而低于溶液法制备的石墨烯膜(通常是103—104Ω/平方).     

Preparation of porous polyimide/in‐situ reduced graphene oxide composite films for electromagnetic interference shielding

Herein we report an easy and efficient approach to prepare lightweight porous polyimide (PI)/reduced graphene oxide (RGO) composite films. First, porous poly (amic acid) (PAA)/graphene oxide (GO) composite films were prepared via non‐solvent induced phase separation (NIPS) process. Afterwards PAA was converted into PI through thermal imidization and simultaneously GO dispersed in PAA matrix was in situ thermally reduced to RGO. The GO undergoing the same thermal treatment process as thermal imidization was characterized with thermogravimetric analysis, Raman spectra, X‐ray photoelectron spectroscopy and X‐ray diffraction to demonstrate that GO was in situ reduced during thermal imidization process. The resultant porous PI/RGO composite film (500‐µm thickness), which was prepared from pristine PAA/GO composite with 8 wt% GO, exhibited effective electrical conductivity of 0.015 S m^?1 and excellent specific shielding efficiency value of 693 dB cm² g^?1. In addition, the thermal stability of the porous PI/RGO composite films was also dramatically enhanced. Compared with that of porous PI film, the 5% weight loss temperature of the composite film mentioned above was improved from 525°C to 538°C. Moreover, tensile test showed that the composite film mentioned above possessed a tensile strength of 6.97 MPa and Young's modulus of 545 MPa, respectively. Copyright © 2016 John Wiley & Sons, Ltd.     

Preparation and characterization of corn starch/soy protein biocomposite film reinforced with graphene and graphene oxide nanoplatelets

Corn starch (CS) and soy protein isolate (SPI), as inexpensive, abundant, and biodegradable materials, can chemically interact well with each other to produce biofilms. However, to overcome some of their physical and mechanical limitations, it is preferred to use their composite form, employing reinforcing materials. In this study, initially, graphene (G) and graphene oxide (GO) were synthesized by a green method. Then, to enhance the polymer blend final properties, the effects of adding G and GO in the range of 0.5 to 2 wt% on physical and mechanical properties of starch/protein blend were investigated. The results showed that the presence of 0.5‐wt% G and 2‐wt% GO significantly increased the modulus of starch/protein film from 252 to 578 and 449 MPa, respectively. In addition, the thermal stability of CS/SPI/GO (2 wt%) composite film was 50°C to 60°C more than that of the pure starch/protein film. On the other hand, G‐reinforced composite films tended to decline water diffusion compared with the pure polymer film. In addition, the composite film with 2‐wt% GO content had the lowest oxygen permeation rate (3.48 cm³ μm/m²d kpa) among the other composite films.     

Formation of homogeneous nanocomposite films at ambient temperature via miniemulsion polymerization using graphene oxide as surfactant

A convenient and industrially scalable method for synthesis of homogeneous nanocomposite films comprising poly(styrene‐stat‐butyl acrylate) and nanodimensional graphene oxide (GO) or reduced GO (rGO) is presented. Importantly, the nanocomposite latex undergoes film formation at ambient temperature, thus alleviating any need for high temperature or high pressure methods such as compression molding. The method entails synthesis of an aqueous nanocomposite latex via miniemulsion copolymerization relying on nanodimensional GO sheets as sole surfactant, followed by ambient temperature film formation resulting in homogeneous film. For comparison, a similar latex obtained by physical mixing of a polymer latex with an aqueous GO dispersion results in severe phase separation, illustrating that the miniemulsion approach using GO as surfactant is key to obtaining homogeneous nanocomposite films. Finally, it is demonstrated that the GO sheets can be readily reduced to rGO in situ by heat treatment of the film. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2289–2297     

Roll‐to‐Roll printed PEDOT/PSS/GO Plastic Film for Electrochemical Determination of Carbofuran

In this work, we developed a roll‐to‐roll printed poly(3,4‐ethylenedioxythiophene)/polystyrene sulphoanate without graphene oxide (GO) (PEDOT/PSS) and with graphene oxide (PEDOT/PSS/GO) plastic films for the electrochemical determination of carbofuran. Both the PEDOT/PSS and PEDOT/PSS/GO plastic films showed electroactivity towards the oxidation of carbofuran. Incorporation of graphene oxide (GO) improves the electrochemical activity of carbofuran and increased its sensitivity. The printed plastic films were characterized by cyclic voltammetry (CV), linear sweep voltammetry (LSV), surface profilometer, four point probe and atomic force microscopy (AFM). The effects of pH, deposition time, deposition potential and film thickness on the oxidation peak current of carbofuran were investigated. Under the optimized conditions, a dynamic linear range of 1 μM–90 μM with a detection limit of 1.0×10^?7 M (S/N=3) were obtained. The printed PEDOT/PSS/GO plastic electrode was applied for the determination of carbofuran in vegetable and fruit samples with recoveries between 94.4 and 101.8 %.     

新型十二烷基三甲氧基硅烷/氧化石墨烯复合膜对430不锈钢耐蚀性能的影响

使用一步电沉积法在430不锈钢上制备出十二烷基三甲氧基硅烷(DTES)/氧化石墨烯(GO)复合膜。 拉曼光谱(Raman)与扫描电子显微镜(SEM)测试表明,氧化石墨烯均匀地混合在硅烷膜中,并用电化学交流阻抗与极化曲线方法对这种复合膜所保护的430不锈钢进行耐蚀性能测试。 结果显示,在3.5%NaCl溶液中,430不锈钢会发生腐蚀反应,而存在硅烷复合膜的430不锈钢的耐蚀性能显著地提高。 研究表明,由于氧化石墨烯出色的阻隔性能一定程度上弥补了硅烷膜的缺陷,而且延长了腐蚀介质通过硅烷基质的路径,因此复合膜有着对基底物质更强的保护性能。     

Comparing Structural and Electrical Properties of Fluorinated Graphene,Graphene Oxide,and Graphene Films Functionalized with N-Methylpyrrolidone

The article presents comparison of structural and electrical properties of fluorinated graphene (FG), graphene oxide (GO), and graphene films functionalized with N-methylpyrrolidone (G-NMP). The obtained functionalized graphene films were continuous, having no ruptures, their thickness was 20–50 nm. Fluorinated films are formed from fluorinated areas and corrugated graphene islets. The size and shape of microstructures on G-NMP surfaces depend on the duration of NMP treatment. GO films demonstrate a rippled surface morphology. The resistance of all films of functionalized graphene exceeds that of pristine graphene films (several kilohms). GO and FG films exhibit dielectric properties. Current-voltage characteristics of FG demonstrate two features: stepwise current increase and negative differential resistance (NDR). Functionalized graphene can be used in flexible electronics, particularly in planar printing technologies.