超临界CO2协助三单体接枝改性聚丙烯

利用超临界二氧化碳(SC CO2)作为单体的溶剂和聚丙烯的溶胀剂, 通过自由基接枝聚合合成了聚丙烯与丙烯酸、甲基丙烯酸甲酯以及马来酸酐的接枝产物PP-g-(AA-MMA-MAH). 在单体的选择上采取软、硬单体复配的方式来调节链的柔韧性. 考察了溶胀条件、接枝条件以及单体配比对接枝反应的影响, 研究结果表明, PP和单体以及引发剂在7.74 MPa、47 ℃下溶胀5 h后, 75 ℃下反应3 h时接枝率为4.31%, 接枝效率可达71.83%. 产品表征说明单体均匀地接枝到聚丙烯颗粒上; 改性后聚丙烯水润湿角降低, 亲水性能得到明显改善; 接枝单体的引入提高了PP的热稳定性.     

聚丙烯熔融接枝马来酸酐反应机理的研究

改变聚丙烯（PP）熔融接枝马来酸酐（MAH）反应中的单体和引发剂的浓度以及添加适当助剂,考察了接枝产物的接枝率和恒定剪切应力（600kPa)及温度（210℃）下的剪切粘度,验证了作先前所提出的PP熔融接枝MAH的反应机理。即：在PP熔融接枝MAH的过程中,过氧化物自由基在熔融接枝过程中直接引发MAH单体及MAH单体在聚丙烯的大分子链段发生β断裂前直接被其引发而产生的接枝反应是影响产物的接枝率和分子量的关键。在不改变单体和引发剂浓度的情况下,降低过氧化物自由基在熔融接枝过程中直接引发MAH单体反应的程度而提高聚丙烯的大分子自由基直接引发MAH单体的反应趋势,是提高接枝产物接枝率和分子量的有效途径。     

甲基丙烯酸缩水甘油酯/苯乙烯固相接枝聚丙烯

以苯乙烯(St)为共单体，过氧化苯甲酰(BPO)为引发剂，采用固相接枝反应将甲基丙烯酸缩水甘油酯(GMA)接枝到聚丙烯(PP)大分子链上。研究了反应时间、单体用量、引发剂用量等因素对接枝率的影响。采用凝胶渗透色谱(GPE)测定了PP和接枝物PP-g-(GMA-St)的分子量和分子量分布。结果 表明固相接枝PP反应条件为[GMA／[St]=2，反应3．5h，加入GMA 10份，BPO 5份。St的加入有助于GMA与PP的接枝，同时在一定程度上抑制了PP的降解。     

聚丙烯接枝改性及其挤出发泡研究

以有机过氧化物为引发剂,以双螺杆挤出机为反应器,将线型不饱和聚酯(ULP)接枝到聚丙烯(PP)分子链上。通过FTIR、DSC及凝胶含量测试,对MPP的结构和性能进行了研究,表明PP发生了接枝反应;泷变性能和熔体流动速率(MFR)测定表明,接枝反应有效地改善了PP流变性能,用双螺杆挤出机对未接枝和接枝的PP进行了发泡研究,SEM分析表明接枝PP具有更好的发泡效果。     

纤维素纳米纤维接枝聚(N-异丙基丙烯酰胺)水凝胶的制备与表征

将具有温度响应的聚N-异丙基丙烯酰胺(PNIPAm)接枝到电纺纤维素纳米纤维膜上,制备温度响应型纤维素接枝聚N-异丙基丙烯酰胺(PNIPAm-g-Cell)纳米纤维水凝胶。 研究接枝单体(N)与纤维素(c)的质量比、反应温度、反应时间和引发剂浓度对产物接枝率、溶胀性和形貌的影响。 结果表明,最佳聚合反应条件为m(N):m(c)=15:1、反应温度40 ℃、反应时间3 h、引发剂浓度为10 mmol/L,得到PNIPAm-g-Cell接枝率和溶胀率分别为35%和31%。 与PNIPAm相比,PNIPAm-g-Cell水凝胶的低临界相转变温度(LCST)显著升高,说明亲水性纤维素的引入改变了体系的亲疏水平衡。 去溶胀动力学测试表明,0.5 min内接枝率为25%和35%的水凝胶保水率分别降低至93%和61%。 说明接枝率越高PNIPAm-g-Cell水凝胶对温度的响应速度越快,对温度越敏感。     

一缩二乙醇二甲基丙烯酸酯对真丝接枝的反应性

研究了一缩二乙二醇二甲基丙烯酸酯在空气存在下，用过硫酸钾(KPS)在水液 中对真丝的接枝。对接枝的条件，如单体、引发剂、甲酸(FA)和乳化剂OP的浓度以 及温度和时间对接枝率的影响进行了测试。发现了较佳的接枝条件是：温度 = 80 ℃，时间 = 30 min，[KPS] = 1.85% (owm)，[OP] = 1% (owf)，[FA] = 0.2%。 接枝率的大小可以用单体浓度来调节，接枝活化能是86.94 kJ/mol。     

一缩二乙醇二甲基丙烯酸酯对真丝接枝的反应性

研究了一缩二乙二醇二甲基丙烯酸酯在空气存在下，用过硫酸钾(KPS)在水液 中对真丝的接枝。对接枝的条件，如单体、引发剂、甲酸(FA)和乳化剂OP的浓度以 及温度和时间对接枝率的影响进行了测试。发现了较佳的接枝条件是：温度 = 80 ℃，时间 = 30 min，[KPS] = 1.85% (owm)，[OP] = 1% (owf)，[FA] = 0.2%。 接枝率的大小可以用单体浓度来调节，接枝活化能是86.94 kJ/mol。     

淀粉接枝丙烯酸/醋酸乙烯酯高吸水性树脂的制备

以过硫酸铵为引发剂,N,N-亚甲基双丙烯酰胺为交联剂,淀粉与丙烯酸/醋酸乙烯酯混合单体通过接枝共聚,制备了吸水及耐盐性能均较好的淀粉接枝丙烯酸/醋酸乙烯酯高吸水性树脂(CGAV)。最佳工艺条件为:淀粉10.0 g,m(混合单体)∶m(淀粉)=4∶1,w(引发剂)=0.3%,w(交联剂)=0.05%,于45℃反应2h~3 h。在最佳工艺条件下制得的CGAV吸去离子水率760 g.g-1,吸0.9%NaC l水溶液率68 g.g-1。     

在超临界CO_2中进行的PP固相接枝改性研究进展

由于性价比高,聚丙烯(PP)成为增长最快的通用塑料,在汽车工业、家用电器和管材方面得到了广泛地应用。然而由于聚丙烯自身的非极性限制了其在某些领域的应用,向聚丙烯主链上接枝极性单体是改善其极性的有效方法。常用的接枝改性方法有:溶液接枝、熔融接枝、等离子体处理、表面可控活性聚合以及超临界CO2状态下接枝等。其中超临界CO2由于溶解单体能力强,对聚合物基体也有很好的溶胀能力,且阻燃性好、无毒以及价格相对低廉,克服了传统接枝方法存在的操作工艺复杂,溶剂不易回收等缺点,得到了广泛研究。本文从超临界CO2协助固相接枝改性机理、接枝单体的选择、影响过程的因素以及超临界CO2协助固相接枝的应用等方面出发,系统阐述了超临界CO2协助PP固相接枝改性近些年来的研究概况。     

含羧基和吡啶基两性离子交换纤维的制备研究

采用γ射线预辐照PP纤维引发 4VP和AA(或AANa)或 4VP和MAA(或MAANa)接枝共聚 ,制得不同接枝率和不同链段结构的弱酸弱碱两性离子交换纤维。采用 4VP/AANa共接枝时 ,在不同单体投料比范围内获得高于 4 2 0 %的总接枝率。研究了纤维的预辐照剂量、单体浓度、摩尔盐含量、交联剂含量以及接枝温度和时间等条件对接枝共聚反应的影响。适宜的接枝共聚反应条件为 :预辐照剂量为 8× 10 4Gy ,单体浓度 10 % ,摩尔盐加入量约 0 .0 5 % ,交联剂用量 2 % ,接枝温度 65℃ ,时间 4h。发现两性纤维呈现双螺旋结构形态。对比自制的弱酸、弱碱离子交换纤维 ,所制备的两性纤维对酸性、中性、碱性氨基酸的吸附量比较大 ,对不同氨基酸具有不同的吸附分离能力     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.     

Copper-catalyzed multicomponent reactions of 2-iodoanilines,benzylamines, and elemental sulfur toward 2-arylbenzothiazoles

A relatively cheap copper salt-catalyzed, three-component approach providing 2-arylbenzothiazoles in good to excellent yields from readily available 2-iodoanilines, benzylamines, and sulfur powder is reported. This methodology allows preparation of various classes of 2-arylbenzothiazoles and provides a general, reliable approach.