Interference-free determination of thallium in aqua regia leaches from rocks, soils and sediments by D(2)-ETAAS method using mixed palladium-citric acid-lithium chemical modifier

The mixture of palladium (chloride) with citric acid and lithium is proposed as a new chemical modifier for the elimination of interference occurred during the determination of Tl in aqua regia extracts from rocks, soils and sediments by electrothermal atomic absorption spectrometry using instrumentation with deuterium-lamp background correction (D₂-ETAAS). Palladium was preferred to rhodium and platinum as to analyte stabilization, citric acid served as an effective reducing agent facilitating formation of Pd-Tl stable covalent bonds playing an important role in the analyte stabilization. Citric acid in addition helps to remove most of interfering chloride at low temperature. The further addition of Li increased significantly the robustness of chemical modifier against strongly interfering ZnCl₂ matrix by binding free chlorine into a more stable LiCl molecule. In the presence of the proposed chemical modifier the temperature for the final step of pyrolysis was adjustable up to 1000 °C, without any noticeable loss of volatile Tl species and the interference of the rest chloride matrix was significantly reduced. The application of the modifier to direct determination of Tl in aqua regia extracts from rocks, soils and sediments has ensured the characteristic mass and LOD value for the original sample 13 pg and 0.043 μg g⁻¹, respectively (10-μL aliquots of sample) and has enabled the use of matrix-free standard solutions for attaining accurate analysis. The accuracy was verified by the analysis of certified reference samples and by the comparison of results with those found by an inductively coupled plasma orthogonal acceleration time-of-flight mass spectrometer (ICP-oa-TOFMS) method.     

Overcoming interference from the alumina matrix on the determination of arsenic at 189 nanometers using electrothermal atomic absorption spectrometry

A method is described enabling to eliminate the spectral interference from alumina matrix onto As determination at the wavelength 189 nm by electrothermal atomic absorption spectrometry with deuterium background correction. Matrix modification was performed by the addition of ammonium fluoride to protect the formation of aluminium oxide implicated in causing spectral interference and to increase volatility of alumina matrix via the formation of AlF₃. Pre-treating of the pyrolytic graphite platform with a solution of rhodium and citric acid has enabled to stabilize the analyte up to temperature of 1300 °C at which most of AlF₃ could be removed from the graphite furnace. The application of 2 μg of Rh + 20 μg of citric acid + 200 μg of NH₄F has enabled an accurate and interference-free determination of As up to 40 μg of Al in the form of AlCl₃ as verified by analytical recoveries study and resulted in characteristic mass and LOD value in the original sample 15 pg and 50 ng g⁻¹, respectively (10-μL aliquots of sample).     

Determination of cadmium, copper and lead in soils, sediments and sea water samples by ETAAS using a Sc + Pd + NH(4)NO(3) chemical modifier

Cadmium, copper and lead in soils, sediments and spiked sea water samples have been determined by electrothermal atomic absorption spectrometry (ETAAS) with Zeeman effect background corrector using NH₄NO₃, Sc, Pd, Sc + NH₄NO₃, Pd + NH₄NO₃, Sc + Pd and Sc + Pd + NH₄NO₃ as chemical modifiers. A comprehensive comparison was made among the modifiers and without modifier in terms of pyrolysis and atomization temperatures, atomization and background absorption profiles, characteristic masses, detection limits and accuracy of the determinations. Sc + Pd + NH₄NO₃ modifier mixture was found to be preferable for the determination of analytes in soil and sediment certified and standard reference materials, and sea water samples because it increased the pyrolysis temperature up to 900 °C for Cd, 1350 °C for Cu and 1300 °C for Pb. Optimum masses of mixed modifier components found are 20 μg Sc + 4 μg Pd + 8 μg NH₄NO₃. Characteristic masses of Cd, Cu and Pb obtained are 0.6, 5.3 and 15.8 pg, respectively. The detection limits of Cd, Cu and Pb were found to be 0.08, 0.57 and 0.83 μg l⁻¹, respectively. Depending on the solid sample type, the percent recoveries were increased up to 103% for Cd, Cu and Pb by using the proposed modifier mixture. The accuracy of the determination of analytes in the sea water samples was also increased.     

Direct determination of vanadium in high saline produced waters from offshore petroleum exploration by electrothermal atomic absorption spectrometry

The present work reports the development of a methodology for the direct determination of vanadium in high saline waters derived from offshore petroleum exploration employing electrothermal atomic absorption spectrometry. Such waters, usually called produced waters, present complex composition containing various organic and inorganic substances. In order to attain best conditions (highest sensitivity besides lowest background) for the methodology, studies about the effects of several variables (evaluation of pyrolysis and atomization temperatures, type of chemical modifier, concentration of modifier and pyrolysis time) and the convenient calibration strategy were performed. Best conditions were reached with the addition of 10 μg of NH₄H₂PO₄ as chemical modifier employing pyrolysis (during 10 s) and atomization temperatures of 1500 and 2700 °C, respectively. Obtained results indicated that, in this kind of sample, vanadium can be determined by standard addition method or employing an external calibration approach with standard solutions prepared in 0.8 mol l⁻¹ NaCl medium. In order to evaluate possible matrix interferences, a recovery test was performed with five spiked samples of produced waters. The limit of detection, limit of quantification and relative standard deviation in 0.8 mol l⁻¹ NaCl medium were also calculated and the derived values were 1.9 μg l⁻¹, 6.3 μg l⁻¹ and 5.6% (at 10 μg l⁻¹ level), respectively.     

Study on the simultaneous determination of some essential and toxic trace elements in honey by multi-element graphite furnace atomic absorption spectrometry

A multi-element graphite furnace atomic absorption spectrometry (GFAAS) method was elaborated and applied for the simultaneous determination of As, Cd, Cr, Cu, and Pb in various kinds of honey samples (acacia, floral, linden, rape, and milkweed) using the transversally heated graphite atomiser (THGA) with end-capped tubes and integrated graphite platforms (IGPs). For comparative GFAAS analysis, direct (without digestion) and indirect (with digestion in a microwave oven) sample preparation procedures were tested. The effects of several chemical modifiers, such as NH₄H₂PO₄, NH₄H₂PO₄-Mg(NO₃)₂, and Pd(NO₃)₂-Mg(NO₃)₂, were studied to obtain optimal pyrolysis and atomization conditions for the set of analytes studied. The most efficient modifier was proved to be the mixture of 5 μg Pd (applied as nitrate) plus 3 μg Mg(NO₃)₂, allowing the optimal 600 °C pyrolysis and 2300 °C atomization temperatures. To prevent the sputtering and foaming of the matrix during the drying and pyrolysis steps of the furnace heating program, the sample and modifier solutions (20 + 5 μl, respectively) were dispensed together onto the IGP of the THGA pre-heated at 80 °C.The effect of increasing concentration of honey matrix was studied on the integrated absorbance (A_int) signals of analytes. The A_int signals of Cr and Pb were not altered up to 10% (m/v) matrix content in the sample solutions. The matrix effect was slightly suppressive on the A_int signals of As, Cd, and Cu above 2% (m/v) honey concentration. The recovery was found to be ranged between 85 and 115% for Cd, Cr, Cu, and Pb, whereas it was a lower, compromise value of 70-99% for As. The limit of detection (LOD) data were 1, 0.04, 0.09, 0.3, and 0.6 μg l⁻¹ for As, Cd, Cr, Cu, and Pb, respectively, which values correspond to 20, 0.8, 1.8, 5.3, and 12 ng g⁻¹, respectively, in the solid samples. The characteristic masses were found to be 21 pg As, 1.3 pg Cd, 4 pg Cr, 12 pg Cu, and 33 pg Pb. The As, Cd, Cr, Cu, and Pb contents of the studied 42 honey samples varied significantly, i.e. from below the LOD up to 13, 3.3, 109, 445, and 163 ng g⁻¹, respectively.     

Determination of selenium in human milk by electrothermal atomic absorption spectrometry and chemical modification

A method was developed for the determination of selenium in human milk using electrothermal atomic absorption spectrometry. The use of chemical modifiers as well as their implications during the pyrolysis step was examined. The chemical modifiers that were studied were Zr, Ir as well as the mixed modifier Zr-Ir. The Ir modifier stabilized selenium at 1000 °C, Zr at 800 °C, while the mixed modifier at 1200 °C. The effect of modifier mass was studied and was found that better results are achieved with addition of 2 μg Zr and 2 μg Ir. The characteristic masses of selenium in the presence of Zr, Ir and the mixed modifier were found to be 73.3, 18.0 and 14.7 pg, respectively, while the corresponding limits of detection were found 2.0, 0.50 and 0.41 μg l⁻¹. Consequently better results were obtained with the mixed modifier. The developed method was applied for the determination of selenium in human milk, which was digested with a HNO₃ + H₂O₂ mixture in a microwave oven. The limit of detection of the method was 1.37 μg l⁻¹, the characteristic mass, m₀, was 48.8 pg and the repeatability was less than 5% as R.S.D.(%). Matrix matched calibration was used. Recoveries were estimated to be 93-105%. The method was applied to breast milk of Greek women (n = 9) and the Se content was found to be in the range 16.7-42.6 μg l⁻¹ with mean value 27.4 ± 5.5 μg l⁻¹.     

A comparative study of chemical modifiers in the determination of total arsenic in marine food by tungsten coil electrothermal atomic absorption spectrometry

Three platinum group elements (Pd, Ir and Rh) both in solution and in pre-reduced form, and also combined with Mg(NO₃)₂ or ascorbic acid, were assessed as possible chemical modifiers on the atomization of As in digest solutions of seafood matrices (clam and fish tissue) by tungsten coil electrothermal atomic absorption spectrometry (TCA-AAS) and compared without a modifier. Of 28 modifier alternatives in study including single form and binary mixtures, and based on maximum pyrolysis temperature without significant As loss and best As absorbance sensitivity during atomization, three modifiers: Rh (0.5 μg), Ir (1.0 μg) and Rh (0.5 μg) + ascorbic acid (0.5 μg), at optimum amounts were pre-selected and compared. The definitive modifier (rhodium (0.5 μg)) was selected by variance analysis. The mean within-day repeatability was 3% in consecutive measurements (25-300 μg l⁻¹) (three cycles, each of n = 6) and showed good short-term stability of the absorbance measurements. The mean reproducibility was 4% (n = 18 in a 3-day period) and the detection limit (3σ_blank/slope) was 42 pg (n = 16). Quantitation was by standard additions to compensate for matrix effects not corrected by the modifier. Three sample digestion procedures were compared in fish and clam tissue samples: microwave acid digestion alone (A) or combined with the addition of 2% (m/v) K₂S₂O₈ solution followed either by UV photo-oxidation (B) or re-digestion in a thermal block (C). The accuracy was established by determination of As in certified reference material of dogfish muscle (DORM-2). Procedures B and C showed good recoveries (102% (n = 4) and 103% (n = 7), respectively), whereas procedure A was not quantitative (85%). The methodology is simple, fast, reliable, of low cost and was applied to the determination of total As in lyophilized samples of clam and fish collected in the Chilean coast.     

Development of methodologies to determine aluminum, cadmium, chromium and lead in drinking water by ET AAS using permanent modifiers

In this work, methodologies were developed to determine aluminum (Al), cadmium chromium and lead in drinking water by electrothermal atomic absorption spectrometry using permanent modifiers. No use of modifier, iridium, ruthenium, rhodium and zirconium (independently, 500 μg) were tested to each one analyte through the pyrolysis and atomization temperatures curves. As the matrix is very simple, did not had occurred problems with the background for all metals. The best results obtained for cadmium and chromium was with the use of rhodium permanent modifier. For lead and aluminum, the best choice was the use of zirconium. The selection for the modifier took into account the sensitivity, form of the absorption pulse and low atomization temperature (what contributes to elevate the useful life of the graphite tube). For aluminum using zirconium permanent, the best pyrolysis and atomization temperatures were respectively, of 1000 and 2500 °C with a characteristic mass (1% of absorbance, m_o) of 19 pg (recommended of 20 pg). For cadmium, with use of rhodium the best temperatures for the pyrolysis and atomization were respectively of 400 and 1100 °C, with a symmetrical peak and with a m_o of 1.0 pg (recommended of 1.0 pg). For chromium with rhodium permanent, the best temperatures for pyrolysis and atomization were respectively of 1000 and 2200 °C, with symmetrical peak and m_o of 5.3 pg (recommended of 5.5 pg). For lead with zirconium permanent, the best temperatures for pyrolysis and atomization were of 700 and 2400 °C, with symmetrical peak and with m_o of 30 pg (recommended of 20 pg). Water samples spiked with each one of the metals in four different levels inside of the acceptable values presented recoveries always close to 100%. The detection limits were of 0.1 μg l⁻¹ for cadmium; 0.2 μg l⁻¹ for chromium; 0.5 μg l⁻¹ for lead and 1.4 μg l⁻¹ for aluminum.     

Comparison of different permanent chemical modifiers for lead determination in Orujo spirits by electrothermal atomic absorption spectrometry

Different analytical methods for the determination of lead in Orujo spirits by electrothermal atomic absorption spectrometry (ETAAS) were developed using permanent modifiers (W, Ir, Ru, W-Ir and W-Ru) thermally deposited on platforms inserted in pyrolitic graphite tubes and Pd-Mg(NO₃)₂ conventional modifier mixture. In all cases, the Pb determination was performed without any sample pretreatment or preconcentration steps. The comparison between the chemical modifiers employed has been made in terms of pyrolysis and atomization temperatures, characteristic masses, detection limits, and atomization and background signal shapes. The limits of detection obtained were 0.375, 0.387, 0.109, 0.251 and 0.267 ng mL⁻¹ for W, Ir, Ru, W-Ir and W-Ru, respectively and 0.710 ng mL⁻¹ for Pd-Mg(NO₃)₂. The characteristic masses were 14.1, 11.2, 5.6, 8.3 and 9.3 pg for W, Ir, Ru, W-Ir and W-Ru, respectively and 22.2 pg for Pd-Mg(NO₃)₂. For all the developed procedures using the different modification systems, the relative standard deviations (<10%) and the analytical recoveries (95-103%) were acceptable. The more suitable methods for Pb determination in distillate spirits were those using permanent modifiers in contrast with classical Pd-Mg(NO₃)₂. The best analytical performance was achieved for W, Ir and W-Ir methods, which were applied to lead determination in Orujo spirit samples from Galicia (NW Spain). The Pb concentrations found in the analyzed samples were comprised in the range (<LOD to 1.5 μg mL⁻¹).     

Determination of traces of Ni in Li(2)CO(3)/Na(2)CO(3) melts by graphite furnace atomic absorption spectrometry

A graphite furnace atomic absorption method is described for the determination of traces of Ni in 52 mole percent (mol.%) Li₂CO₃ and 48 mol.% Na₂CO₃ melts after dissolution of the sample in dilute nitric acid. Maximum pyrolysis and optimum atomisation temperatures for the analyte were determined in the presence of the Li and Na matrix constituents. Pre-pyrolysed ascorbic acid (typical amount of 5 μg) has been used as chemical modifier for effectively suppressing the chemical and spectral interferences of the Li/Na matrix, thus that the analysis can be conducted using acid-matched standard solutions. The results of the Ni analysis in synthetic sample solutions by calibration graph against acid-matched standards well agree with those obtained by the method of standard additions. Recoveries ranged from 99 to 101% and the relative standard deviation is around 3% at the 20 μg L⁻¹ level. Moreover, the use of the chemical modifier leads to an improvement of the lifetime of the graphite tube. The Ni detection limit (3σ) in Li/Na carbonate melts for the proposed method is similar to that obtained in aqueous solution, i.e. 5 × 10⁻⁸ g analyte per gram of (Li_0.52Na_0.48) ₂CO₃ melt. This method is successfully applied to the determination of nickel in real carbonate melt samples.     

Solid sampling-graphite furnace atomic absorption spectrometry for the direct determination of boron in plant tissues

In this work, the potential of graphite furnace atomic absorption spectrometry for the direct determination of B in plant tissues has been investigated. Three certified reference materials (NIST SRM 1570a spinach leaves, NIST SRM 1573a tomato leaves and BCR CRM 679 white cabbage) were selected for this study, the goal always being to develop a fast procedure that could be robust enough to provide a satisfactory performance for all of them, without any modifications in the conditions applied.The use of a suitable chemical modifier was found to be essential for obtaining a reproducible and sufficiently sensitive signal for boron solutions. In this regard, the performance of the combination of citric acid plus W (added as a permanent modifier) was noteworthy, resulting in well-defined signal profiles, a remarkable analyte stabilization during the pyrolysis step (up to 2100 °C) and minimal memory effects. This mixture of modifiers provided a good performance for the direct analysis of solid samples as well, but only if a suitable temperature program, favoring the interaction between the analyte and the modifiers, was used. Thus, such a temperature program, with two pyrolysis steps and the addition of NH₄NO₃ in order to carry out the in situ sample microdigestion, was optimized. Under these conditions, the peak areas obtained for both solid samples and aqueous standards were comparable.Finally, the analysis of the samples was carried out. In all cases, a good agreement with the certified values was obtained, while R.S.D. values ranged between 6 and 10%. It can be concluded that the method proposed shows significant advantages for the determination of this complicated element in solid samples such as the use of aqueous standards for calibration, a high sample throughput (20 min per sample), a suitable limit of detection (0.3 μg g⁻¹) and reduced risk of analyte losses and contamination.     

Bio-oil production from Onopordum acanthium L. by slow pyrolysis

In this study, the usability of the plant thistle, Onopordum acanthium L., belonging to the family Asteraceae (Compositae), in liquid fuel production has been investigated. The experiments were performed in a fixed-bed Heinze pyrolysis reactor to investigate the effects of heating rate, pyrolysis temperature and sepiolite percentage on the pyrolysis product yields and chemical compositions. Experiments were carried out in a static atmosphere with a heating rate of 7 °C/min and 40 °C/min, pyrolysis temperature of 350, 400, 500, 550 and 700 °C and particle size of 0.6 < D_p < 0.85 mm. Catalyst experiments were conducted in a static atmosphere with a heating rate of 40 °C/min, pyrolysis temperature of 550 °C and particle size of 0.6 < D_p < 0.85 mm. Bio-oil yield increased from 18.5% to 27.3% with the presence of 10% of sepiolite catalyst at pyrolysis temperature of 550 °C, with a heating rate of 40 °C/min, and particle size of 0.6 < D_p < 0.85 mm. It means that the yield of bio-oil was increased at around 48.0% after the catalyst added. Chromatographic and spectroscopic studies on the bio-oil showed that the oil obtained from O. acanthium L. could be used as a renewable fuels and chemical feedstock.     

Ammonium fluoride as a novel chemical modifier for the elimination of magnesium chloride interference on the determination of lead by graphite furnace atomic absorption spectrometry

Ammonium fluoride was found to be very efficient modifier for the elimination of MgCl₂ interference on Pb determination. Ammonium fluoride probably converts strongly interfering volatile MgCl₂ to less volatile MgF₂ matrix that makes possible the release of Pb analyte at lower temperature, before the matrix starts to vaporize. It was observed likewise that NH₄F removes the interferences mentioned, i.e. caused by MgCl₂ presence, much more effectively as compared with some modifiers, before now recommended for this purpose. The application of this modifier to the determination of Pb in 2% (m/v) MgCl₂ has ensured the characteristic mass and LOD value in the original sample of 12 pg and 60 ng g⁻¹, respectively (10 μl aliquots of sample). Applying the modifier to standards and samples enables the use of matrix-free standard solutions for attaining accurate analysis as verified by recovery studies.     

Preparation and pyrolysis of poly(allyl iminoalane-co-ethyl iminoalane)s [HAlN(allyl)]m[HAlNEt]n

Poly(allyl iminoalane-co-ethyl iminoalane)s {[HAlN(allyl)]_m[HAlNEt]_n; Allyl/Et-alanes}, have been prepared by reactions of lithium hydridoaluminate (LiAlH₄) with a mixture of allylamine hydrochloride (CH₂CHCH₂NH₂ · HCl; allylNH₂ · HCl) and ethylamine hydrochloride (CH₃CH₂NH₂ · HCl; EtNH₂ · HCl) with various allyl/Et ratios. Spectroscopic analyses indicate that Allyl/Et-alane(1/3) (allyl/Et = 1/3) contains octamers possessing Al-H and C-H groups as well as CC, Al-N, and C-N bonds. The loss of aluminum during pyrolysis of Allyl/Et-alane(1/3) at 1600 °C under an Ar atmosphere is 15%, which is less than the value reported for the pyrolysis of poly(ethyliminoalane) (36%). The suppression can be ascribed to cross-linking reactions involving allyl groups (hydroalumination and polymerization of the allyl groups), judging from infrared (IR) and solid-state nuclear magnetic resonance (NMR) spectroscopy.     

The use of silver nanoparticles as an effective modifier for the determination of arsenic and antimony by electrothermal atomic absorption spectrometry

Silver nanoparticles (AgNPs) were proposed as a new chemical modifier for the elimination of interferences when determining arsenic and antimony in aqueous NaCl or Na₂SO₄ solutions and in sea-water by electrothermal atomic absorption spectrometry. For this purpose, the AgNPs were prepared simply by reducing silver nitrate with sodium citrate. The effects of pyrolysis and atomization temperatures and the amounts of interferents and modifiers on the sensitivities of these elements were investigated. In the presence of the proposed modifier, a pyrolysis temperature of at least 1100 °C for arsenic and 900 °C for antimony could be applied without the loss of analytes, and the interferences were greatly reduced to allow for interference-free determination. The detection limits (N = 10, 3σ) for arsenic and antimony were 0.022 ng and 0.046 ng, respectively. AgNPs are cheaper and more available compared to many other modifiers. No background was detected, and the blank values were negligible.     

Analysis of pyrolysis products formed from ethylene-tetrafluoroethylene heterosequences of poly(ethylene-co-tetrafluoroethylene)

Poly(ethylene-co-tetrafluoroethylene) (PETFE) was pyrolyzed and the pyrolysis products formed from the ethylene-tetrafluoroethylene heterosequences were analyzed using gas chromatography/mass spectrometry (GC/MS). Major pyrolysis products were 3,3-difluoropropene (DFP), 3,3,4,4-tetrafluoro-1-butene (TFB), 1,1,2,2,3,3-hexafluorocyclopentane (HFCP), 1,1,2,2,3,3-hexafluorocyclohexane (HFCH), 1,1,2,2,3,3,4,4-octafluorocyclohexane (OFCH), and 3-trifluoromethyl-3,4,4,5,5-pentafluorocyclohexene (FMPFCH). Their formation mechanisms were proposed. Peak intensity ratios of HFCP, HFCH, and FMPFCH compared to OFCH increased as the pyrolysis temperature increased, while those of DFP, TFB, HFCP, and HFCH compared to tetrafluoroethylene decreased. Order of the relative abundances of the major pyrolysis products formed from PETFE was OFCH > HFCP > HFCH > TFB > DFP. The order may be due to the difference in bond energies of CH₂-CH₂, CF₂-CH₂, and CF₂-CF₂. Formation of the pyrolysis product through the CH₂-CH₂ bond cleavage was more favorable than those through the CF₂-CH₂ and CF₂-CF₂ ones.     

Comparison of direct solid sampling and slurry sampling for the determination of cadmium in wheat flour by electrothermal atomic absorption spectrometry

Two analytical methods for the determination of cadmium in wheat flour by electrothermal atomic absorption spectrometry without prior sample digestion have been compared: direct solid sampling analysis (SS) and slurry sampling (SlS). Besides the conventional modifier mixture of palladium and magnesium nitrates (10 μg Pd + 3 μg Mg), 0.05% (v/v) Triton X-100 has been added to improve the penetration of the modifier solution into the solid sample, and 0.1% H₂O₂ in order to promote an in situ digestion for SS. For SlS, 30 μg Pd, 12 μg Mg and 0.05% (v/v) Triton X-100 have been used as the modifier mixture. Under these conditions, and using a pyrolysis temperature of 800 °C, essentially no background absorption was observed with an atomization temperature of 1600 °C. About 2 mg of sample have been typically used for SS, although as much as 3-5 mg could have been introduced. In the case of SlS multiple injections had to be used to achieve the sensitivity required for this determination. Calibration against aqueous standards was feasible for both methods. The characteristic mass obtained with SS was 0.6 pg, and that with SlS was 1.0 pg. The limits of detection were 0.4 and 0.7 ng g⁻¹, the limits of quantification were 1.3 and 2.3 ng g⁻¹ and the relative standard deviation (n = 5) was 6-16% and 9-23% for SS and SlS, respectively. The accuracy was confirmed by the analysis of certified reference materials. The two methods were applied for the determination of cadmium in six wheat flour samples acquired in supermarkets of different Brazilian cities. The cadmium content varied between 8.9 ± 0.5 and 13 ± 2 ng g⁻¹ (n = 5). Direct SS gave results similar to those obtained with SlS using multi-injections; the values of both techniques showed no statistically significant difference at the 95% confidence level. Direct SS was finally adopted as the method of choice, due to its greater simplicity, the faster speed of analysis and the better figures of merit.     

Determination of palladium in various samples by atomic absorption spectrometry after preconcentration with dimethylglyoxime on silica gel

A preconcentration method based on the adsorption of palladium-dimethylglyoxime (DMG) complex on silica gel for the determination of palladium at trace levels by atomic absorption spectrometry (AAS) has been developed. The retained palladium as Pd(DMG)₂ complex was eluted with 1 mol l⁻¹ HCl in acetone. The effect of some analytical parameters such as pH, amount of reagent and the sample volume on the recovery of palladium was examined in synthetic solutions containing street dust matrix. The influence of some matrix ions on the recovery of palladium was investigated by using the developed method when the elements were present both individually and together. The results showed that 2500 μg ml⁻¹ Na⁺, K⁺, Mg²⁺, Al³⁺ and Fe³⁺; 5000 μg ml⁻¹ Ca²⁺ ; 500 μg ml⁻¹ Pb²⁺; 125 μg ml⁻¹ Zn²⁺; 50 μg ml⁻¹ Cu²⁺ and 25 μg ml⁻¹ Ni²⁺ did not interfere with the palladium signal. At the optimum conditions determined experimentally, the recovery for palladium was found to be 95.3±1.2% at the 95% confidence level. The relative standard deviation and limit of detection (3s/b) of the method were found to be 1.7% and 1.2 μg l⁻¹, respectively. In order to determine the adsorption behaviour of silica gel, the adsorption isotherm of palladium was studied and the binding equilibrium constant and adsorption capacity were calculated to be 0.38 l mg⁻¹ and 4.06 mg g⁻¹, respectively. The determination of palladium in various samples was performed by using both flame AAS and graphite furnace AAS. The proposed method was successfully applied for the determination of palladium in the street dust, anode slime, rock and catalytic converter samples.     

Aqua bridged Cu2 dimer of a heptadentate N4O3 coordinating ligand: Synthesis,structure and magnetic properties

The N₄O₃ coordinating heptadentate imidazolidinyl phenolate ligand, H₃L (2-(2′-hydroxyphenyl)-1,3-bis[4-(2-hydroxyphenyl)-3-azabut-3-enyl]-1,3-imidazolidine) forms with Cu(II) a rare aqua bridged complex [{Cu₂(μ-L)(μ-H₂O)}₂](ClO₄)₂ · 4.5H₂O (1 · 4.5H₂O). Complex 1 · 4.5H₂O contains two crystallographically different but chemically equivalent dinuclear [Cu₂(μ-L)(μ-H₂O)]⁺ cationic units in the asymmetric unit. The copper atoms of each dinuclear unit are in a distorted square-pyramidal environment and are held together by phenolate, imidazolidinyl and aqua bridges with a Cu···Cu separation of av. 3.34 Å. The compound exhibits a very weak antiferromagnetic exchange interaction (J = −0.77 cm⁻¹, ? = −2 J?₁?₂) between the two copper(II) (S = 1/2) ions. The ¹H NMR spectrum of the complex shows a total of 17 hyperfine shifted peaks, as expected from the idealized C_s symmetry of the compound, spread over a very large window of chemical shift, spanning about 250 ppm. The complex, having an appropriate intermetallic separation for catechol binding, shows catecholase like activity in MeCN at 25 °C, with the aerobic oxidation of 3,5-di-tert-butylcatechol (3,5-DTBC) to 3,5-di-tert-butylquinone (3,5-DTBQ).     

Effectiveness of palladium as a chemical modifier for the determination of lead in biological materials and foodstuffs by graphite furnace atomic absorption spectrometry

Summary A combination of 6 g palladium and 15 g magnesium nitrate is proposed as chemical modifier for lead determinations in biological materials and foodstuffs. The applicability of this modifier was investigated by the analysis of several types of samples, as compared to the classical NH₄H₂PO₄ and Mg(NO₃)₂ modifier. Direct determinations of lead against aqueous standard solutions can be performed in 3-fold diluted urine, 2-fold diluted milk and 6-fold diluted blood, when the proposed modifier is added. A method for lead determinations in potatoes using the combined palladium and magnesium nitrate modifier, after a microwave acid digestion, is described. The optimum GFAAS pyrolysis temperature remains dependent on the matrix and should be determined for each type of sample. A wider linear range of the calibration curve is observed when the proposed Pd modifier is used.