Selective determination of acenaphthylene by flow injection analysis with tris(2,2'-bipyridine)ruthenium(II) chemiluminescence detection

A simple, rapid flow injection chemiluminescence (FI-CL) method has been developed for selective determination of acenaphthylene (ACY), based on the CL produced in the reaction of tris(2,2′-bipyridine)ruthenium(III) (Ru(bipy)₃³⁺) and ACY in an acidic buffer solution. Under the optimum experimental conditions, the calibration curve was linear over the range 5.0 × 10⁻³ to 4.0 × 10⁻⁷ mol L⁻¹ for ACY. The detection limit (S/N = 3) was 2.0 × 10⁻⁷ mol L⁻¹ and the relative standard deviation of 10 replicate measurements was 2.3% for 5.0 × 10⁻⁵ mol L⁻¹ of ACY. Selectivity of CL reaction of ACY from other 15 polycyclic aromatic hydrocarbons (PAHs) was investigated by flow injection method. The method was applied to determine the ACY content in soil.     

Electrochemiluminescence from Ru(bpy)3 immobilized in poly(3,4-ethylenedioxythiophene)/poly(styrenesulfonate)-poly(vinyl alcohol) composite films

Electrochemical behavior and electrogenerated chemiluminescence (ECL) of tris(2,2′-bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺) immobilized in poly(3,4-ethylenedioxythiophene)/poly(styrenesulfonate)-poly(vinyl alcohol) (PEDOT/PSS-PVA) composite films via ion-exchange have been investigated with tripropylamine (TPA) as the co-reactant at a glassy carbon electrode. The immobilized Ru(bpy)₃²⁺ performed a surface-controlled electrode reaction. The Ru(bpy)₃²⁺ modified electrode showed a fast ECL response to TPA, and was used for the ECL detection of TPA with high sensitivity. The ECL intensity was linearly related to concentrations of TPA over the range from 0.50 μmol L⁻¹ to 0.80 mmol L⁻¹, and the detection limit was 0.10 μmol L⁻¹ (S/N = 3). The as-prepared electrode exhibited good precision and long-term stability for TPA determination.     

Enhancement of on chip chemiluminescence signal intensity of tris(1,10-phenanthroline)-ruthenium(II) peroxydisulphate system for analysis of chlorpheniramine maleate in pharmaceutical formulations

The effect of detection chip geometry on chemiluminescence (CL) signal intensity of tris(1,10-phenanthroline)-ruthenium(II) peroxydisulphate system for analysis of chlorpheniramine maleate (CPM) in pharmaceutical formulations was investigated. It was observed that the design of the detection chip is very crucial and can play an important role in enhancing the CL signal intensity in this system. The CL signal intensity was enhanced 250% when a teardrop micromixer chip was used, compared to the commonly used serpentine chip geometry. The study was conducted using a multi-chip device. In this device, chip 1 was used to prepare and pump the reagent mixture, whereas chip 3 was used for pumping the sample. The two chips were connected to the teardrop chip (2) via silica capillary where detection took place. Non-linear regression curve fitting of the calibration data revealed that the calibration curves are best described by third order polynomial equation with excellent correlation coefficients (R² = 0.9998) for the concentration range 7.69 × 10⁻⁸ to 5.12 × 10⁻⁵ mol L⁻¹. A linear response is also observed over the range 7.69 × 10⁻⁸ to 1.28 × 10⁻⁵ mol L⁻¹ (R² = 0.9996) and the detection limit was found to be 5.49 × 10⁻⁸ mol L⁻¹. The device was successfully used for the analysis of CPM in tablets and a multi-component cough syrup. Results were reproducible with relative standard deviation (RSD) of 0.6-1.1%.     

Tris(2,2'-bipyridyl)ruthenium(II)-Zirconia-Nafion composite modified electrode applied as solid-state electrochemiluminescence detector on electrophoretic microchip for detection of pharmaceuticals of tramadol, lidocaine and ofloxacin

Tris(2,2′-bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺)-Zirconia-Nafion composite modified glassy carbon disk electrode as a solid-state electrochemiluminescence (ECL) detector is successfully applied to an electrophoretic microchip system with a wall-jet configuration. Pharmaceuticals such as tramadol, lidocaine and ofloxacin were selected to characterize the performance of this microchip capillary electrophoresis (CE)-ECL detection system. Voltammetric and ECL behaviors of immobilized Ru(bpy)₃²⁺ were investigated in lidocaine system. Influences of the separation electric field to cyclic voltammograms (CVs) of the immobilized Ru(bpy)₃²⁺ were also investigated. Tramadol, lidocaine and ofloxacin can be baseline separated without any additives. The detection limits (S/N = 3) were 2.5 × 10⁻⁵ mol L⁻¹ for tramadol, 5.0 × 10⁻⁶ mol L⁻¹ for lidocaine, 1.0 × 10⁻⁵ mol L⁻¹ for ofloxacin under the sample injection of picoliters, and the linear ranges were from 5.0 × 10⁻⁵ to 2.5 × 10⁻³ mol L⁻¹ for tramadol, 1.0 × 10⁻⁵ to 1.0 × 10⁻³ mol L⁻¹ for lidocaine, and 1.0 × 10⁻⁵ to 2.5 × 10⁻³ mol L⁻¹ for ofloxacin, respectively.     

Determination of diphenhydramine by capillary electrophoresis with tris(2,2'-bipyridyl)ruthenium(II) electrochemiluminescence detection

Tris(2,2′-bipyridyl)ruthenium(II) electrochemiluminescence detection in a capillary electrophoresis separation system was used for the determination of diphenhydramine. In this study, platinum disk electrode (300 μm in diameter) was used as a working electrode and the influence of applied potential and buffer conditions were investigated. Under optimal conditions: 1.2 V applied potential, pH 8.50, 15 kV separation voltage and 10 mmol l⁻¹ running buffer, the calibration curve of diphenhydramine was linear over the range of 4×10⁻⁸ to 1×10⁻⁵ mol l⁻¹. This technique gave satisfactory precision, and relative standard deviations of migration times and chemiluminescence peak intensities were less than 1 and 6%, respectively. The technique was applied to animal studies for determination of diphenhydramine extracted from rabbit plasma and urine samples, and the extraction efficiency were between 92 and 98.5%.     

Flow injection chemiluminescence determination of paracetamol

A simple chemiluminometric method using flow injection has been developed for the determination of paracetamol (acetaminophen), based on the chemiluminescence produced by the reduction of tris(2,2′-bipyridyl)ruthenium(III). The latter is obtained by oxidation of tris(2,2′-bipyridyl)ruthenium(II) by potassium permanganate in dilute sulphuric acid in the presence of paracetamol. A standard or sample solution was injected into the ruthenium(II) stream (flow rate 1.5 ml min⁻¹) which was then merged with potassium permanganate in dilute sulphuric acid stream (flow rate 0.5 ml min⁻¹). The chemiluminescence intensity is enhanced by the presence of manganese(II) ions. Under the optimum conditions, a linear calibration graph was obtained over the range of 0.3-50.0 μg ml⁻¹ and the detection limit was 0.2 μg ml⁻¹ (s/n = 3). The relative standard deviation of the proposed method calculated from 20 replicate injections of 5.0 μg ml⁻¹ paracetamol was 1.1%. The sample throughput was 90 h⁻¹. The method was successfully applied to the determination of paracetamol in commercial pharmaceutical formulations.     

A novel solid-state electrochemiluminescence detector for capillary electrophoresis based on tris(2,2'-bipyridyl)ruthenium(II) immobilized in Nafion/PTC-NH2 composite film

A new electrochemiluminescence (ECL) detector for capillary electrophoresis (CE) based on tris(2,2′-bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺) immobilized in Nafion/PTC-NH₂ (an ammonolysis product of 3,4,9,10-perylenetetracarboxylic dianhydride (PTCDA)) composite film was presented for the first time. The Nafion/PTC-NH₂ composite film could effectively immobilize tris(2,2′-bipyridyl)ruthenium(II) via ion-exchange and electrostatic interaction. Cyclic voltammetric and ECL behavior of Nafion/PTC-NH₂/Ru composite film was investigated compared to Nafion/Ru composite. The Nafion/PTC-NH₂/Ru composite film exhibited good ECL stability and simple operability. Then the CE with solid-state ECL detector system was successfully used to detect sophora - a quinolizidine type - alkaloids as sophoridine (SR) and matrine (MT). The CE-ECL parameters that affected separation and detection were optimized. Under the optimized conditions, the linear range was from 2.5 × 10⁻⁸ to 2 × 10⁻⁶ mol/L for SR, 1.0 × 10⁻⁸ to 1.0 × 10⁻⁶ mol/L for MT. The detection limit (S/N = 3) was estimated to be 5 × 10⁻⁹ and 10⁻⁹ mol/L for SR and MT, respectively. It was shown that the CE coupling with solid-state ECL detector system exhibited satisfying sensitivity of analysis.     

Zirconium ion selective electrode based on bis(diphenylphosphino) ferrocene incorporated in a poly(vinyl chloride) matrix

A novel potentiometric zirconium - PVC matrix membrane sensor incorporating bis(diphenylphosphino) ferrocene as an electroactive material and tris(2-ethylhexyl)phosphate as solvent mediator is described. In mixed acetate buffer solution of pH 4.8, the sensor displays a rapid and linear response for zirconium ion over the concentration range 1.0 × 10⁻¹ to 1.0 × 10⁻⁷ mol L⁻¹ with a good slope of 59.7 ± 0.3 mV per decade and detection limit 1.8 × 10⁻⁸ mol L⁻¹. The best performance was obtained with membrane composition 33% PVC, 65% TEHP, 1% NaTPB and 1% ionophore. The proposed electrode revealed excellent selectivity for zirconium ion over a wide variety of alkali, alkaline earth, transition and heavy metal ions and could be used in a pH range of 4.15-7.8. The electrode was applied for at least 1 month without any considerable divergence in the potential responses. The practical utility of the electrode has been demonstrated by its use as an indicator electrode in the potentiometric titration of zirconium ions with sodium fluoride and in determination of zirconium ion in some alloy, tape and waste water samples.     

Electrochemiluminescent behaviors of alkaloids and tris(2,2'-bipyridine) ruthenium in organically modified silicate film

Electrogenerated chemiluminescences (ECLs) of alkaloids, such as berberine, trigonelline, allantoin and betaine, were studied in an aqueous alkaline buffer solution (pH 9.5), based on tris(2,2′-bipyridine)ruthenium(II) [Ru(bpy)₃²⁺] immobilized in organically modified silicates (ORMOSILs) film on a glassy carbon electrode (GCE). The immobilized Ru(bpy)₃²⁺ showed good electrochemical and photochemical activities. In a flow system, the eluted alkaloids were oxidized on the modified GCE, and reacted with immobilized Ru(bpy)₃²⁺ at the potential of +1.50 V (versus Ag/AgCl). The luminescence with λ_max 610 nm was caused by a reaction of electrolytically formed Ru(bpy)₃³⁺ with an oxidized amine group to generate Ru(bpy)₃^2+*. The determination limit was 5 × 10⁻⁶ mol L⁻¹, 8 × 10⁻⁶ mol L⁻¹, 2.0 × 10⁻⁵ mol L⁻¹ and 5.0 × 10⁻⁵ mol L⁻¹ for berberine, trigonelline, allantoin and betaine at S/N 3, respectively. In addition, the factors affecting the determination of the four alkaloids were also studied.     

Simultaneous determination of amiodarone and its metabolite desethylamiodarone by high-performance liquid chromatography with chemiluminescent detection

A novel method was developed for the determination of amiodarone and desethylamiodarone by high-performance liquid chromatography (HPLC) coupled with chemiluminescent (CL) detection. The procedure is based on the post-column photolysis of the analytes into photoproducts which are active in the tris(2,2′-bipyridyl)ruthenium(III) [Ru(bpy)₃³⁺] CL system. Ru(bpy)₃³⁺ was on-line generated by photo-oxidation of the Ru(II) complex in the presence of peroxydisulfate. The separation was carried out on a Mediterranea C₁₈ column with isocratic elution using a mixture of methanol and 0.017 mol L⁻¹ ammonium sulfate buffer of pH 6.8. Under the optimum conditions, analytical curves, based on standard solutions, were linear over the range 0.1-50 μg mL⁻¹ for amiodarone and 0.5-25 μg mL⁻¹ for desethylamiodarone. The detection limits of amiodarone and desethylamiodarone were 0.02 and 0.11 μg mL⁻¹, respectively. Intra- and inter-day precision values of 0.9% relative standard deviation (R.S.D.) (n = 10) and 1.6% R.S.D. (n = 15), respectively, were obtained. The method was applied successfully to the determination of these compounds in serum and pharmaceutical formulations.     

Simultaneous determination of butylated hydroxyanisole (BHA) and butylated hydroxytoluene (BHT) in food samples using a carbon composite electrode modified with Cu3(PO4)2 immobilized in polyester resin

A simple electrochemical method was developed for the single and simultaneous determination of butylated hydroxyanisole (BHA) and butylated hydroxytoluene (BHT) in food samples using square-wave voltammetry (SWV). A carbon composite electrode modified (MCCE) with copper (II) phosphate immobilized in a polyester resin was proposed. The modified electrode allowed the detection of BHA and BHT at potentials lower than those observed at unmodified electrodes. A separation of about 430 mV between the peak oxidation potentials of BHA and BHT in binary mixtures was obtained. The calibration curves for the simultaneous determination of BHA and BHT demonstrated an excellent linear response in the range from 3.4 × 10⁻⁷ to 4.1 × 10⁻⁵ mol L⁻¹ for both compounds. The detection limits for the simultaneous determination of BHA and BHT were 7.2 × 10⁻⁸ and 9.3 × 10⁻⁸ mol L⁻¹, respectively. In addition, the stability and repeatability of the electrode were determined. The proposed method was successfully applied in the simultaneous determination of BHA and BHT in several food samples, and the results obtained were found to be similar to those obtained using the high performance liquid chromatography method with agreement at 95% confidence level.     

Determination of glyphosate mono-isopropylamine salt in process samples using flow injection analysis with tris(2,2'-bipyridyl)ruthenium(II) chemiluminescence detection

The mono-isopropylamine salt of glyphosate was selectively determined directly in industrial and commercial formulations using flow injection analysis with tris(2,2′-bipyridyl)ruthenium(II) chemiluminescence detection without the need for separation. Glyphosate and its mono-isopropylamine salt furnished detection limits of 7×10⁻⁹ and 3.5×10⁻¹⁰ M and relative standard deviations of 0.4% at 1×10⁻⁷ M and 0.8% at 5×10⁻⁸ M, respectively. The methodology is robust and reliable with samples subjected only to aqueous dilution prior to analysis.     

Capillary electrophoresis-electrochemiluminescent detection of N,N-dimethyl ethanolamine and its application in impurity profiling and stability investigation of meclophenoxate

Numerous drugs are carboxylic acid derivatives containing amino group, and hydrolysis reaction of these agents often generates toxic amines. Thus, the detection of amine impurity is of great importance in drug quality control of these amino group-containing ester and amide. A capillary electrophoresis method coupled with end-column electrochemiluminescent detection based on tris(2,2′-bipyridyl)ruthenium(II) system was proposed for the analysis of N,N-dimethyl ethanolamine (DMEA, the degradation product of meclophenoxate) in the presence of its precursor. Baseline separation of DMEA and meclophenoxate can be easily achieved under the selected conditions. DMEA can be assayed within 3 min over the concentration range of 5.0 × 10⁻⁸ to 3.0 × 10⁻⁶ mol L⁻¹ with a detection limit of 2.0 × 10⁻⁸ mol L⁻¹ at the signal-to-noise ratio of 3. The relative standard deviations of the signal intensity and the migration time were less than 5.3 and 2.5% for a standard sample containing 1.0 × 10⁻⁷ mol L⁻¹ DMEA (n = 5), respectively. The presented method has been successfully applied for the profiling of DMEA resulting from the hydrolysis of meclophenoxate in commercial formulations. A primary stability investigation of meclophenoxate in aqueous solution was also carried out at different temperatures, and the results showed that the degradation of meclophenoxate accelerated at the higher temperature.     

Electrochemical determination of iodide on a vanadium oxide-polypropylene carbonate coated glassy carbon electrode

A vanadium oxide-modified glassy carbon electrode was simply and conveniently fabricated by casting vanadium tri(isoproxide) oxide (VO(OC₃H₇)₃) and poly(propylene carbonate) (PPC) onto the glassy carbon electrode surface. The electrochemical properties of iodide at the VO(OC₃H₇)₃-PPC film-modified glassy carbon electrode were investigated by cyclic voltammetry, and an anodic peak was observed at approximately +0.71 V (vs. SCE). Based on this, a sensitive and convenient electrochemical method was proposed for the determination of iodide. Flow injection amperometry (FIA) exhibited a good linear relationship with the concentration of iodide in the range of 5 × 10⁻⁷ mol L⁻¹ and 1 × 10⁻³ mol L⁻¹, and the detection limit was 1 × 10⁻⁷ mol L⁻¹. Quantitative recovery of iodide in synthetic samples has been obtained and the interferences from different cations and anions have been studied. The method has been successfully applied to the determination of iodide in dry edible seaweed. The concentrations of iodide measured by this method are in good agreement with those obtained by spectrophotometric method.     

Determination of proline in wine using flow injection analysis with tris(2,2'-bipyridyl)ruthenium(II) chemiluminescence detection

Flow injection methodology is described for the determination of proline in red and white wines using tris(2,2′-bipyridyl)ruthenium(II) chemiluminescence detection. Selective conditions were achieved for proline at pH 10, while other amino acids and wine components did not interfere. The precision of the method was less than 1.00% (R.S.D.) for five replicates of a standard (4 × 10⁻⁶ M) and the detection limit was 1 × 10⁻⁸ M. The level of proline in white and sparkling wines using the developed methodology was equivalent to those achieved using HPLC-FMOC amino acid analysis. SPE removal of phenolic material was required for red wines to minimize Ru(bipy)₃³⁺ consumption and its associated effect on accuracy.     

FIA-near-infrared spectrofluorimetric trace determination of hydrogen peroxide using tricarchlorobocyanine dye (Cy.7.Cl) and horseradish peroxidase (HRP)

A new kind of near-infrared fluorescence agent, tricarbochlorocyanine dye (Cy.7.Cl), had been synthesized in house and used for near-infrared spectrofluorimetric determination of hydrogen peroxide (H₂O₂) by flow injection analysis (FIA) for the first time. The oxidation reaction of Cy.7.Cl with H₂O₂ occurred under the catalysis of horseradish peroxidase (HRP) and it was studied in detail. The possible reaction mechanism was discussed. Under optimal experimental conditions, fluorescence from Cy.7.Cl displayed excitation and emission maxima (ex/em) at 780 and 800 nm, respectively. The two linear working ranges were 1.86 × 10⁻⁷ to 4.11 × 10⁻⁷ mol L⁻¹ and 4.11 × 10⁻⁷ to 7.19 × 10⁻⁶ mol L⁻¹, respectively. The detection limit was 5.58 × 10⁻⁸ mol L⁻¹ of H₂O₂. The effect of interferences was studied. The proposed method was successfully applied to the determination of hydrogen peroxide in rainwater, serum and plant samples.     

A fast screening method for the presence of atrazine and other triazines in water using flow injection with chemiluminescent detection

Atrazine is a triazine herbicide which contains two secondary aliphatic amine groups. Previous studies have shown that aliphatic amines react with tris(2,2′-bipyridyl)ruthenium(III) to produce chemiluminescence. This paper describes the application of tris(2,2′-bipyridyl)ruthenium(III) to the detection of atrazine and related triazine herbicides in water by flow injection chemiluminescence analysis. The optimised experimental conditions were determined to be: sample and carrier flow rates of 4.6 mL min⁻¹, sample at pH 9 buffered with 50 mM borax, and reagent concentration of 1 mM tris(2,2′-bipyridyl)ruthenium(III) in 20 mM H₂SO₄ (pH 1). Under these conditions, the logarithm of the chemiluminescence intensity versus concentration was linear in the range of 2.15-2150 μg L⁻¹ for samples in MilliQ water, and the limit of detection of atrazine in water was determined to be 1.3 ± 0.1 μg L⁻¹. Validation of the method was performed using direct injection HPLC. The presence of natural organic matter (NOM) significantly increased the chemiluminescence, masking the signal generated by atrazine. Isolating the target analyte via solid phase extraction (SPE) prior to analysis removed this interference and concentrated the samples, resulting in a greatly improved sensitivity with a detection limit of 14 ± 2 ng L⁻¹.     

A microflow chemiluminescence system for determination of chloramphenicol in honey with preconcentration using a molecularly imprinted polymer

A novel chemiluminescence (CL) microfluidic system incorporating a molecularly imprinted polymer (MIP) preconcentration step was used for the determination of chloramphenicol in honey samples. The MIP was prepared by using chloramphenicol as the template, diethylaminoethyl methacrylate (DAM) as the function monomer, ethylene glycol dimethacrylate (EGDMA) as the cross-linking monomer, 2, 2′-dimethoxy-2-phenylacetophenone (DMPA) as the free radical initiator and toluene and dodecanol as the solvent. The MIP was pre-loaded into a 10 mm long, 2 mm wide and 150 μm deep channel in a planar glass microfluidic device. When the sample containing chloramphenicol was introduced into the microfluidic device it was first preconcentrated on the MIP then detected by an enhancement effect on the chemiluminescence reaction of tris(2, 2′-bipyridyl) ruthenium(II) with cerium(IV) sulphate in sulphuric acid. A micro-syringe pump was used to pump the reagents. The CL intensity was linear in relationship to the chloramphenicol concentrations from 1.55 × 10⁻⁴ to 3.09 × 10⁻³ μmol L⁻¹ (r² = 0.9915) and the detection limit (3σ) and the quantitation limit (10σ) were found to be 7.46 × 10⁻⁶ and 2.48 × 10⁻⁵ μmol L⁻¹, respectively. This method offered a high selectivity and sensitivity for quantitative analysis of chloramphenicol in the honey samples.     

Chemiluminescence determination of citrate and pyruvate and their mixtures by the stopped-flow mixing technique

A novel kinetic chemiluminescent method using the stopped-flow mixing technique has been investigated for the rapid and sensitive determination of citrate and pyruvate. The method is based on a tris(2,2′-bipyridiyl)ruthenium(III) (Ru(bpy)₃³⁺) chemiluminescence (CL) reaction. Ru(bpy)₃³⁺ was generated in the mixing chamber by oxidising tris(2,2′-bipyridyl)ruthenium(II) with cerium(IV). After selecting the best operating parameters, calibration graphs were obtained over the concentration ranges 0.38-38 μg ml⁻¹ and 8.7-1300 ng ml⁻¹ for citrate and pyruvate, respectively. The limits of detection were 0.1 μg ml⁻¹ for citrate and 0.3 ng ml⁻¹ for pyruvate. Based on the differential rate of the chemiluminescent reaction corresponding to citrate and pyruvate, a very simple kinetic procedure was developed for the simultaneous determination of both compounds. Mixtures of citrate and pyruvate in ratios between 15:1 and 1.5:1 were satisfactorily resolved. The proposed method was successfully applied to the determination of citrate in pharmaceutical formulations, pyruvate in animal blood serum and both compounds in human urine.     

Carbon and diamond paste microelectrodes based on Mn(III) porphyrins for the determination of dopamine

Three Mn(III) porphyrins were used for the design of carbon paste and diamond paste based microelectrodes, which were employed for the determination of dopamine in pharmaceutical and biological samples using differential pulse voltammetry (DPV). The limits of detection lie between 1.6 × 10⁻¹³ and 2.0 × 10⁻⁶ mol L⁻¹ while the sensitivities were between 230 pA μmol L⁻¹ and 3.24 μA mol L⁻¹. Dopamine was recovered reliable from pharmaceutical and biological samples in percentages higher than 91.00% and 92.00%, respectively. The surface of the microelectrodes can easily be renewed by simple polishing, obtaining a fresh surface ready for use in a new assay.