Fast determination of nicotine and 3-ethenylpyridine in indoor environments

Summary Different sampling and analysis techniques for the determination of gas-phase nicotine and 3-ethenylpyridine in environmental tobacco smoke are reported. Graphitized carbon traps, annular diffusion denuders, and nebulizer collectors have been used as sampling devices in combination with either thermal desorption or with water extraction. Capillary gas chromatography and ion-pair reversed-phase chromatography were applied to desorbed and liquid samples obtained in an intercomparison indoor study. The methods developed here show some advantages over existing methods in terms of analysis time, sensitivity and loading capacity.     

An improved headspace solid-phase microextraction method for the analysis of free-base nicotine in particulate phase of mainstream cigarette smoke

The content of free-base nicotine in cigarette smoke is a controversial subject, partly due to methodological issues. In this investigation, an improved method to measure free-base nicotine in cigarette smoke using headspace solid-phase microextraction (HS-SPME) combined with GC/MS analysis, was developed and validated for this purpose. Cigarette smoke particulate phase (PP) was collected onto a 44 mm glass fiber filter pad. The pad was cut in halves with one half used to determine the concentrations of total nicotine and water. The remaining half was analyzed by HS-SPME for free-base nicotine. The following factors were found to have a significant impact on the responses of free-base nicotine: SPME fiber type, pre-equilibrium time before HS-SPME, extraction time and temperature, PP water content, and the solvent used for the preparation of standards. It was also found that the impact of PP water content on the determination of free-base nicotine from smoke sample could be corrected by a water correction factor calculated based on an experimentally determined reciprocal model. The precision of the method was evaluated with smoke samples of reference cigarettes: Canadian flue-cured monitor and Kentucky reference 2R4F. The RSD values obtained were in the 12.8-16.8% range.     

On-line solid phase extraction - thermal desorption for introduction of large volumes of aqueous samples into a gas chromatograph

A new approach to the introduction of large aqueous samples into a gas chromatograph, solid phase extraction - thermal desorption, is presented. Carrier gas pushes the sample through a packed liner mounted in a programmed temperature vaporizer; analytes retained by the packing material are thermally desorbed after drying of the adsorbent. The sorption properties and thermal stability of some packing materials have been studied off-line. Tenax GC®, and octyl-modified silica silylated with diphenyltetramethyldisilazane to improve its thermal stability, appeared to be suitable materials. The drying period and the desorption temperature are critical for satisfactory performance of the method. When Tenax GC® is used as packing material, thermal desorption at 250°C for 15 min gives quantitative recovery for methyl esters up to hexacosanoic acid methyl ester. With the silylated octyl-modified silica, the application range is limited to the methyl esters of decanoic to octadecanoic acids.     

Graphitized carbon black in quartz tubes for the sampling of indoor air nicotine and analysis by microwave thermal desorption-capillary gas chromatography

Nicotine in a smoky indoor air environment can be determined using graphitized carbon black as a solid sorbent in quartz tubes. The temperature stability, high purity, and heat absorption characteristics of the sorbent, as well as the permeability of the quartz tubes to microwaves, enable the thermal desorption by means of microwaves after active sampling. Permeation and dynamic dilution procedures for the generation of nicotine in the vapor phase at low and high concentrations are used to evaluate the performances of the sampler. Tube preparation is described and the microwave desorption temperature is measured. Breakthrough volume is determined to allow sampling at 0.1-1 L/min for definite periods of time. The procedure is tested for the determination of gas and paticulate phase nicotine in sidestream smoke produced in an experimental chamber.     

Solid-phase microcolumn extraction and gas chromatography-mass spectrometry identification of volatile organic compounds emitted by paper

A rapid non-destructive sampling technique for the analysis of volatile organic compounds (VOCs) emitted by paper sheets is described. A capillary, which is connected to a microcolumn packed with Tenax TA, is inserted between two sheets at the centre of a paper stack encapsulated inside a PET/Al/PE composite foil. The other end of the microcolumn is connected to a gas-tight syringe and an appropriate volume of gaseous phase is aspirated. The microcolumn is then thermally desorbed in a modified GC inlet (modification is presented) and analysed by gas chromatography-mass spectrometry (GC-MS). In the chromatogram from the analysis of artificially aged paper sample 21 compounds were identified. Advantages of the method including the short sampling time (1 min), simplicity and economic aspect are discussed.     

Fast analysis of nicotine related alkaloids in tobacco and cigarette smoke by megabore capillary gas chromatography

A novel fast megabore capillary gas chromatographic (MCGC) method for analysis of 7 nicotine related alkaloids in tobacco and cigarette smoke, including nicotine, nornicotine, myosmine, nicotyrine, anabasine, anatabine and 2,3-dipyridyl, was developed. The use of megabore capillary column GC methodology, equipped with flame ionization detector (FID), provided rapid, unambiguous nicotine related alkaloids analysis. One gram flue-cured tobacco (or Cambridge filter pad), 20 ml ether, and 5 ml 10% sodium hydroxide solution, added with n-heptadecane as the internal standard, were placed in a flask, and the flask was capped and placed in an ultrasonic bath for 15 min. A 1 microl volume was analyzed by capillary GC operating in split-injection mode on a mega bore Simplicity-5 column. This simple procedure was compared with the previously reported packed column GC method and the Griffith still-colorimetric method. The application of the method for analysis of various flue-cured tobaccos and cigarette smoke was discussed.     

Simultaneous determination of nicotine and 3-vinylpyridine in single cigarette tobacco smoke and in indoor air using direct extraction to solid phase

The aim of the present study was to develop a new analytical method of chromatographic determination of two important markers of ETS exposure: nicotine and 3-vinylpyridine (3-ethenylpyridine, 3-EP) in mainstream (MS) and sidestream (SS) smoke of one single cigarette and in indoor air using direct solid phase extraction combined with gas chromatography. The method can be utilised for both nicotine and 3-EP determination in SS and MS of one single cigarette as well as it allows for a precise determination of compound distribution in indoor air. The application of the same analytical method for both kinds of samples allows anticipating indoor air distribution of both analysed compounds in a very precise way. The precision of the method (calculated as a relative standard deviation) was 9.78% for nicotine and 2.67% for 3-EP; whereas the accuracy (evaluated by a recovery study conducted at three different levels) was 70.1 and 87.3%, respectively. The limit of detection was 0.06 µg per cigarette for both nicotine and 3-EP. The method was evaluated by determining the compounds of interest in two commercially available brands of cigarettes as well as in the reference cigarettes 3R4F and also in indoor air polluted with tobacco smoke. Determined levels of compounds of interest in MS varied from 586 to 772 (nicotine) µg per cigarette and from 3.5 to 10.7 (3-EP) µg per cigarette. In SS smoke the level varied from 14,370 to 22,590 (nicotine) µg per cigarette and from 185 to 550 (3-EP) µg per cigarette, whereas levels in indoor air polluted with tobacco smoke varied from 50.1 to 157.3 (nicotine) µg m^?3and from 7.7 to 20.8 (3-EP) µg m^?3.     

Analysis of polycyclic aromatic hydrocarbons in the particulate phase of cigarette smoke using a gas chromatographic-high-resolution mass spectrometric technique

A new procedure is developed for the extraction of polycyclic aromatic hydrocarbons (PAHs) from the particulate phase of cigarette smoke. The procedure applies solid-phase extraction using a Bond Elut CH cartridge as a sample preparation step. The efficiency of the cleanup procedure is verified using a gas chromatographic (GC)-high-resolution mass spectrometric (MS) technique, proving that no interference occurs in the PAHs' determination. The efficient cleanup allows GC detection using either high- or low-resolution MS detection. Enhanced sensitivity is obtained using GC-MS and selected ion monitoring. This new technique has several advantages over other reported techniques. The method is simple and robust and has good repeatability and accuracy. The estimated detection limit is 0.1 ng/cigarette for benzo[a]pyrene. In addition to that, the recovery from the smoke pad in which the smoke is collected is approximately 97% for all PAHs. Results for the PAH analyses for 1R5F, 1R4F, and 1R3 Kentucky reference cigarettes are reported in this study. These results provide useful evidence for clarifying the controversy about previously reported data.     

Simultaneous on-line size and chemical analysis of gas phase and particulate phase of cigarette mainstream smoke

This paper describes the combined set-up of on-line chemical analysis of gas phase by single-photon ionisation/resonance enhanced multiphoton ionisation–time-of-flight mass spectrometry (SPI/REMPI-TOFMS) and on-line particle size analysis by differential electrical mobility particle spectrometry (DMS 500) for the investigation of fresh cigarette mainstream smoke. SPI is well suited for the investigation of a great variety of organic species, whereas REMPI is highly sensitive for aromatic compounds. Gas phase measurements of filtered and unfiltered smoke are possible with the SPI/REMPI-TOFMS in order to determine the influence of the presence of particles on the chemical composition of the gas phase. Initial results are shown for the characterisation and comparison of three pure Virginia tobacco research cigarettes having filter ventilations of 0%, i.e. no filter ventilation, 35% and 70% ventilation. The three cigarette types are smoked under two different smoking regimes, a standard regime using puff parameters equivalent to the conventional International Standard Organisation regime and a more intense smoking regime. For the gas phase, qualitative puff-by-puff resolved yields of three selected compounds (acetaldehyde, phenol and styrene) are shown and compared. For particulate matter, particle number, count median diameter and total surface area are illustrated on a puff-by-puff basis. Yields of the chemicals analysed, puff number and surface area are in good agreement with the intensity of the smoking regime and the dilution of smoke by filter ventilation. However, gaseous compounds are influenced differently, depending whether an absolute particle filter is present or not, i.e. they can be totally removed (phenol), partially removed (styrene) or not affected (acetaldehyde). For particle analysis, the count median diameter decreases from puff to puff and is strongly dependent on the smoking regime and ventilation rate. Thereby, 0% ventilated cigarettes smoked under the intense regime result in the smallest count median diameters of ca. 180 nm, whereas 70% ventilated cigarettes smoked with a standard regime lead to the largest values of up to 280 nm. As particle diameter increases, particle number decreases as a consequence of increasing time for particle coagulation.     

Thermal desorption—gas chromatography for the determination of benzene, aniline, nitrobenzene and chlorobenzene in workplace air

Sampling on Tenax TA of different mesh sizes followed by thermal desorption and gas chromatography was evaluated as a simple method for the determination of benzene, aniline, nitrobenzene and chlorobenzene in the workplace air. An alternative sampling technique in place of pump sampling was developed. Quantitative recoveries were obtained in the mass range 0.04–10 μg. It was found that air humidity had no effect on recovery. The charged tubes can be stored at room temperature for 5 days with no change in recovery. The particle size of Tenax TA has no significant effect on adsorption and desorption.     

The development of sampling and gas chromatography-mass spectrometry analytical procedures to identify and determine the minor organic components of landfill gas

Modified drive-in piezometers provided quick and inexpensive probes to give access to the undiluted landfill gas below ground level. Samples collected on Tenax GC and Porapak Q adsorption tubes were thermally desorbed and injected into a gas Chromatograph through a cold trap. Aqueous condensate samples were injected directly by syringe. Chromosorb 101, Tenax GC and Triton X100/KOH packed columns, and an SE30 capillary column were used, together with full-scan and selective-ion mass spectrometry. Limits of detection, all less than 1 mg m (3), and calibration correlation coefficients were determined for the least tractable components, i.e., free acids, amines and alcohols. A detection limit of 0.1 mg m (3), based on anisole as internal standard, was estimated for all other compounds. The standard deviation for the whole procedure, with full-scan mass spectrometry, was +/-55% of the mean. A large part of this was due to an instrumental error, standard deviation = 33% of the mean, that was inherent in the manual operation of the mass-spectrum chart-recorder. These procedural errors were insignificant in comparison with the variations caused by the type of site and the age of the fill.     

Application of thermal desorption to the development of a gas chromatographic/mass spectrometric method for the determination of toluene,chlorinated aromatic hydrocarbons,and 2,3,7,8-tetrachlorodibenzo-p-dioxin in combustion emissions

A fast and accurate analytical method, which uses commercially available adsorbents (Tenax TA, Carbotrap B and C, and Carbosieve S-III), was developed for the sampling and determination of aromatic hydrocarbons, chloroaromatic compounds, and 2,3,7,8-tetrachlorodibenzo-p-dioxin. The breakthrough volume data show that Carbotrap C has a good capacity for compounds of high molecular weight, whereas Carbosieve S-III and Tenax TA are efficient for volatile compounds. The organic components are thermally desorbed and transferred to a gas chromatograph/mass spectrometer. Importantly, thermal desorption avoids conventional solvent extraction procedures and also allows reuse of adsorbent tubes. Preliminary results for recovery of analytes from tubes packed with single adsorbent prove that a single-adsorbent bed is not capable of sampling a wide range of compounds. The best method to obtain the desired collection and desorption properties is to use adsorbent tubes containing several different materials. The results of optimization studies are summarized.     

Analysis of C10-C20 hydrocarbons in natural gas by solid phase extraction and CGC

A method is described for the determination of C10-C20 hydrocarbons in natural gas. Enrichment by solid phase extraction on ODS followed by liquid desorption was found to give better results than adsorption on Tenax or charcoal followed by liquid or thermal desorption.     

Trace Analysis of Hydrocarbons in Air Using Standard Gas Chromatographic and Personal Sampling Equipment

Abstract

Unmodified standard gas chromatographs are reported to be useful for the determination of a large number of ambient hydrocarbons. Packing of standard injector glass liners with an adsorbent permits thermal desorption in the injector on to the chromatographic column. Coupling to a personal sampling pump permits exposure-related sampling. The potential of the technique is illustrated by applications with the Tenax GC adsorbent. Precautions required to avoid artifacts when working in the subnanogram range are described.     

气提浓缩仪分析水中痕量挥发性有机物研究

本文描述了气提浓缩仪的设计及操作程序用于对水中痕量挥发性有机物的测定。分析物被气提吸附于TenaxGC柱上,然后直接脱附到毛细管气相色谱柱上进行分析,并用FID或MS鉴定。本文除对色谱条件进行优化外,对气提时间和脱附温度等分析操作条件也进行了研究。检测下限为0.01-0.30PPb,峰面积检测精度优于6.9％,对16种化合物的回收率优于74％。     

Gas chromatographic determination of ethyl 2-cyanoacrylate in the workplace environment

Low levels of airborne ethyl 2-cyanoacrylate (ECA) were monitored by drawing air through sampling tubes containing Tenax GC. After desorption with acetone, ECA was quantified by gas chromatography using a thermionic specific detector in the nitrogen mode. Polymerised ECA was shown to yield ECA monomer under the conditions of gas chromatographic analysis.     

Laser desorption fast gas chromatography–Mass spectrometry in supersonic molecular beams

A novel method for fast analysis is presented. It is based on laser desorption injection followed by fast gas chromatography-mass spectrometry (GC-MS) in supersonic molecular beams. The sample was placed in an open air or purged laser desorption compartment, held at atmospheric pressure and near room temperature conditions. Desorption was performed with a XeCl Excimer pulsed laser with pulse energy of typically 3 mJ on the surface. About 20 pulses at 50 Hz were applied for sample injection, resulting in about 0.4 s injection time and one or a few micrograms sample vapor or small particles. The laser desorbed sample was further thermally vaporized at a heated frit glass filter located at the fast GC inlet. Ultrafast GC separation and quantification was achieved with a 50-cm-long megabore column operated with a high carrier gas flow rate of up to 240 mL/min. The high carrier gas flow rate provided effective and efficient entrainment of the laser desorbed species in the sweeping gas. Following the fast GC separation, the sample was analyzed by mass spectrometry in supersonic molecular beams. Both electron ionization and hyperthermal surface ionization were employed for enhanced selectivity and sensitivity. Typical laser desorption analysis time was under 10 s. The laser desorption fast GC-MS was studied and demonstrated with the following sample/matrices combinations, all without sample preparation or extraction: (a) traces of dioctylphthalate plasticizer oil on stainless steel surface and the efficiency of its cleaning; (b) the detection of methylparathion and aldicarb pesticides on orange leaves; (c) water surface analysis for the presence of methylparathion pesticide; (d) caffeine analysis in regular and decaffeinated coffee powder; (e) paracetamol and codeine drug analysis in pain relieving drug tablets; (f) caffeine trace analysis in raw urine; (g) blood analysis for the presence of 1 ppm lidocaine drug. The features and advantages of the laser desorption fast GC-MS are demonstrated and discussed.     

Thermal-desorption gas chromatographic procedure for screening coal fly ash for volatile organic compounds

Thermal desorption of coal fly ash in a flowing stream of helium liberates volatile compounds which are collected on Tenax resin. A chemical “fingerprint” of these components collected from the fly ash is obtained by using thermal desorption of the material collected on the Tenax resin and capillary-column gas chromatography. Compounds ranging in volatility from that of benzene (b.p. 80°C) through C₁-phenanthrene (b.p. ca. 360°C) are detected, but recoveries of components only through naphthalene (b.p. 218°C) are suitable for quantitative work. The method provides chemical information on volatile organic compounds complementary to that achieved by procedures based on solvent extraction.     

Mobile resonance enhanced multiphoton ionisation-time-of-flight mass spectrometer with a novel hybrid laser desorption/molecular beam ion source for rapid detection of aromatic trace compounds from gas phase and solid samples

A mobile, field applicable resonance enhanced multiphoton ionisation-time-of-flight mass spectrometer (REMPI-TOFMS) for direct-inlet gas-phase analysis as well as for characterisation of solid samples, has been developed. For solid-sample analysis, laser desorption (LD) with IR-laser pulses is used for volatilisation of the neutral analytes from a target in the ion source prior to REMPI-TOFMS analysis. For direct inlet gas-phase analysis, a needle gas inlet is used and the formed molecular beam is REMPI-ionised directly in the ion source. A special ion source was developed, which can be rapidly interchanged between the REMPI-TOFMS and the LD-REMPI-TOFMS modes. The system is equipped with a tuneable optical parametrical oscillator (OPO)-laser system. The analytical properties are characterised for both modes of operations. In both cases, analytical performance is similar to that achieved with instruments specifically designed for either gas-phase or solid-phase characterisation. Results from field measurements of a wood combustion flue gas of a 174 kW bio mass furnace are given. Gas-phase analysis was applied for time-resolved on-line REMPI-TOFMS of the semi-volatile aromatic flue gas constituents. The low-volatile aromatic compounds, which were precipitated with the particulate matter in the filtering unit of the sampling train, were characterised by direct LD-REMPI-TOFMS of the glass fibre filter material. By combining the gas-phase and particulate results a rather comprehensive characterisation of the aromatic species present in the flue gas (i.e. aerosol--gas phase plus particulate matter) was achieved.