Development of an electrothermal vaporization ICP–MS method and assessment of its applicability to studies of the homogeneity of reference materials

A method has been developed for measurement of the homogeneity of analyte distribution in powdered materials by use of electrothermal vaporization with inductively coupled plasma mass spectrometric (ETV–ICP–MS) detection. The method enabled the simultaneous determination of As, Cd, Cu, Fe, Mn, Pb, and Zn in milligram amounts of samples of biological origin. The optimized conditions comprised a high plasma power of 1500 W, reduced aerosol transport flow, and heating ramps below 300?°C s^–1. A temperature ramp to 550?°C ensured effective pyrolysis of approximately 70% of the organic compounds without losses of analyte. An additional hold stage at 700?°C led to separation of most of the analyte signals from the evaporation of carbonaceous matrix compounds. The effect of time resolution of signal acquisition on the precision of the ETV measurements was investigated. An increase in the number of masses monitored up to 20 is possible with not more than 1% additional relative standard deviation of results caused by limited temporal resolution of the transient signals. Recording of signals from the nebulization of aqueous standards in each sample run enabled correction for drift of the sensitivity of the ETV–ICP–MS instrument. The applicability of the developed method to homogeneity studies was assessed by use of four certified reference materials. According to the best repeatability observed in these sample runs, the maximum contribution of the method to the standard deviation is approximately 5% to 6% for all the elements investigated.     

Analyte transport efficiency with electrothermal vaporization inductively coupled plasma mass spectrometry

Reported are results for the quantitative determination of absolute transport efficiency in electrothermal vaporization inductively coupled plasma mass spectrometry (ETV-ICP-MS) for the Perkin-Elmer HGA-600MS electrothermal vaporizer. The absolute transport efficiencies for Mo, In, Tl and Bi were determined using experimental conditions typical of those applied to real analysis by ETV-ICP-MS. Experiments using an on-line filter trapping apparatus indicated that particles produced by the ETV device were smaller than 0.1 μm in diameter. The nature and condition of the ETV graphite surface, the length of the transfer tube, and the effect that diluted seawater and palladium modifiers have on analyte transport efficiency were investigated. Transport efficiency was comparable for all elements studied and was enhanced with previously used, rather than new, graphite tubes and when seawater and palladium carriers were present. When analyte was vaporized without carrier from a new graphite tube, the transport efficiency to the plasma was approximately 10%. Approximately 70% of the total amount of analyte vaporized was deposited within the ETV switching valve, 19% onto the transfer tubing and 1% onto the components comprising the torch assembly. These conditions represent the `worst case scenario', with analyte transport to the plasma increasing to approximately 20% or more with the addition of carrier.     

Calibration system and analytical considerations for quantitative sesquiterpene measurements in air

Sesquiterpenes (C15H24, SQT) are semi-volatile organic compounds emitted from vegetation and are of interest for air quality considerations because of their suspected contribution to the formation of secondary aerosol. This article investigates the application of a capillary diffusion method for the generation of standard atmospheres of 16 SQT and four other related semi-volatile compounds. This instrument subsequently has been used in the testing of analytical materials, protocols and calibration of air sampling methods. SQT DB-1 retention indices, vapor pressures at 25 and 75 degrees C, and diffusion coefficients were determined. A quantitative, on-line GC method yielded improved results (median relative standard deviation of 5.0-6.1%) for the diffusion rate determination in comparison to a gravimetric approach (median relative standard deviation 18%). The GC method also allowed identifying errors in the gravimetric method stemming from residual solvent evaporation, impurities, and chemical analyte losses. Stainless steel, glass, nickel and PTFE tubing that were tested for transfer lines and a sampling loop had to be kept at temperatures in excess of approximately 110 degrees C in order to prevent significant analytical errors from the stickiness of SQT to these materials. In addition to SQT analysis, results from this research provide general guidelines for gas-phase analysis of related compounds in the C14-C16 volatility range.     

Validation of LC/MS electrospray ionisation method for the estimation of ursodiol in human plasma and its application in bioequivalence study

A novel High Performance Liquid Chromatography-electrospray mass spectrometric method has been developed for the estimation of Ursodiol (Ursodeoxycholic acid)--a bile acid, in human plasma using Ornidazole as internal standard. The methodology involved solid phase extraction of the analyte from human plasma matrix. The chromatographic separation was achieved within seven minutes by an isocratic mobile phase containing 1.0 mM ammonium acetate and Acetonitrile (65:35, v/v), flowing through XTerra MS C18, 100 x 2.1, 3.5 microm analytical column, at a flow rate of 0.2 ml/min. Ion signals were measured in negative mode for Ursodiol and internal standard at m/z 391.3 and 278.1, respectively. A detailed validation of the method was performed as per USFDA guidelines and the standard curves were found to be linear in the range 50.0 ng/ml to 3000.0 ng/ml with the mean correlation coefficient more than 0.99. The absolute recovery was more than 54.90% for Ursodiol and 76.51% for internal standard. Ursodiol was stable for sixty-nine days at -70 degrees C and for eight hours at ambient temperature. After extraction from plasma, the reconstituted samples of Ursodiol were stable in autosampler at 10 degrees C for forty-eight hours. Upon subjecting to three freeze thaw cycles, there was no change in the recovery of the analyte. The integrity of the plasma samples remained unaffected even upon four-fold dilution with drug free human plasma. The method was simple, specific, sensitive, precise, accurate and suitable for bioequivalence and pharmacokinetic studies. It was successfully applied to the pilot bioequivalence study of Ursodiol in male human subjects.     

Determination of Ga, Ge, As, Se and Sb in fly ash samples by ultrasonic slurry sampling electrothermal vaporization inductively coupled plasma mass spectrometry

Ultrasonic slurry sampling electrothermal vaporization inductively coupled plasma mass spectrometry (USS-ETV-ICP-MS) has been applied to determine Ga, Ge, As, Se and Sb in fly ash samples. The influences of instrument operating conditions and slurry preparation on the ion signals were reported. Pd and ascorbic acid were used as the mixed modifiers to enhance the ion signals. This method has been applied to determine Ga, Ge, As, Se and Sb in NIST SRM 1633a and 1633b coal fly ash reference materials and a fly ash sample collected locally. Since the sensitivities of the elements studied in slurry solution and aqueous solution were different slightly, analyte addition technique was used for the determination of Ga, Ge, As, Se and Sb in these samples. The As and Se analysis results of the reference materials agreed with the certified values. The results for which no certified value was available were also found to be in good agreement between the ETV-ICP-MS results and the reference values. The reference value was obtained by digesting the samples and analyzing the digested sample solutions by pneumatic nebulization Dynamic Reaction Cell™ (DRC) ICP-MS. The method detection limits estimated from analyte addition curves were about 0.23, 0.13, 0.17, 0.25 and 0.11 μg g⁻¹ for Ga, Ge, As, Se and Sb, respectively, in original fly ash samples.     

Ultra-trace determination of Se in sediments by electrothermal vaporizer-inductively coupled plasma-mass spectroscopy: use of the ETV as a thermochemical reactor

The performance of electrothermal vaporization inductively coupled plasma mass spectrometry (ETV-ICP-MS) was evaluated for the ultra-trace determination of total selenium in sediment reference materials. Citric acid, when combined with an appropriate thermal program, promoted the early release of Se in a molecular form from the graphite surface, effecting a separation of the analyte from the concomitant matrix, thereby demonstrating the use of the ETV as a thermochemical reactor. No special sample pretreatment is needed and an absolute detection limit of 10 pg was achieved. Concentrations of Se in different sediment CRMs were determined and results obtained by both isotope dilution (ID) and standard addition (SA) methodologies were compared and evaluated. Mass bias effects prevented accurate application of ID techniques.     

Determination of L-753,037 in human plasma by liquid chromatography/turbo ionspray tandem mass spectrometry.

A liquid chromatographic/turbo ionspray tandem mass spectrometric (LC/MS/MS) method was developed and validated for the determination of L-753,037, a potent endothelin receptor antagonist currently under development for the treatment of cardiovascular diseases, in human plasma. L-753,037 is extracted from 0.5 ml of human plasma using liquid-liquid extraction and analyzed by LC/MS/MS with a turbo ionspray interface. Method validation results showed that this method is very sensitive, reliable, selective and reproducible. L-753,048, an ethoxy analogue of L-753,037, was used as the internal standard. The method has a lower limit of quantitation (LOQ) of 50 pg ml(-1) with a linear calibration range of 0.05-50 ng ml(-1). The intra-day precision and accuracy (n = 5) were measured to be below 10% relative standard deviation (RSD) and between 97.4 and 102.8% of the nominal values, respectively, for all calibration standard concentrations within the calibration curve range. The inter-day precision and accuracy (n = 3 days, 5 replicates per day) were measured to be below 6.5% RSD and between 99.3 and 102.0% of the nominal values, respectively, for all quality control concentrations. The extraction recovery was determined to be approximately 99% on average. The analyte was found to be stable in plasma through three freeze-thaw cycles, for at least 4 h at ambient temperature and for up to 40 days under -20 degrees C freezer storage conditions. The analyte was also shown to be stable for at least 24 h in the reconstitution solution at room temperature and for up to 3 days as a dried extract at 4 degrees C. Additional variations in plasma concentration of the analyte due to the use of different sources of plasma were also evaluated.     

Determination of phosphorus and arsenic in trichlorosilane by electrothermal vaporization-inductively coupled plasma mass spectrometry with prior concentration by cuprous chloride

A method for the determination of trace impurities of phosphorus and arsenic in trichlorosilane with prior separation followed by electrothermal vaporization inductively coupled plasma mass spectrometry (ETV-ICP-MS) has been developed. The preconcentration of the analytes from the sample matrix was made by adding cuprous chloride to a 10 mL trichlorosilane sample for the formation of non-volatile compounds with the elements of interest. Upon evaporation of trichlorosilane, the analytes retained in the residue were then determined in the presence of copper as modifier by ETV-ICP-MS. The dual role of cuprous chloride both in the preconcentration and instrumental determination was investigated and discussed. By meticulous control of experimental conditions, limits of detection for these two elements as low as sub-ng/g can be achieved. The method was applied to the determination of phosphorus and arsenic in a commercially available trichlorosilane sample.     

Electrothermal vaporisation ICP-mass spectrometry (ETV-ICP-MS) for the determination and speciation of trace elements in solid samples - A review of real-life applications from the author's lab

The use of electrothermal vaporisation (ETV) from a graphite furnace as a means of sample introduction in inductively coupled plasma mass spectrometry (ICP-MS) permits the direct analysis of solid samples. A multi-step furnace temperature programme is used to separate the vaporisation of the target element(s) and of the matrix components from one another. Sometimes, a chemical modifier is used to enable a higher thermal pre-treatment temperature, by avoiding premature analyte losses (stabilisation) or promoting the selective volatilisation of matrix components. In almost all instances, accurate results can be obtained via external calibration or single standard addition using an aqueous standard solution. Absolute limits of detection are typically ~1 pg, which corresponds to 1 ng/g for a typical sample mass of 1 mg. Real-life applications carried out in the author's lab are used to illustrate the utility of this approach. These applications aim at trace element determination in industrial and environmental materials. The industrial materials analysed include different types of plastics - Carilon, polyethylene, poly(ethyleneterephtalate) and polyamide - and photo- and thermographic materials. As samples from environmental origin, plant material, animal tissue and sediments were investigated. Some applications aimed at a multi-element determination, while in other, the content of a single, but often challenging, element (e.g., Si or S) had to be measured. ETV-ICP-MS was also used in elemental speciation studies. Separation of Se-containing proteins was accomplished using polyacrylamide gel electrophoresis (PAGE). Subsequent quantification of the Se content in the protein spots was carried out using ETV-ICP-MS. As the volatilisation of methylmercury and inorganic mercury could be separated from one another with respect to time, no chromatographic or electrophoretic separation procedure was required, but ETV-ICP-MS as such sufficed for Hg speciation in fish tissue.     

Determination of phosphorus and arsenic in trichlorosilane by electrothermal vaporization-inductively coupled plasma mass spectrometry with prior concentration by cuprous chloride

A method for the determination of trace impurities of phosphorus and arsenic in trichlorosilane with prior separation followed by electrothermal vaporization inductively coupled plasma mass spectrometry (ETV-ICP-MS) has been developed. The preconcentration of the analytes from the sample matrix was made by adding cuprous chloride to a 10 mL trichlorosilane sample for the formation of non-volatile compounds with the elements of interest. Upon evaporation of trichlorosilane, the analytes retained in the residue were then determined in the presence of copper as modifier by ETV-ICP-MS. The dual role of cuprous chloride both in the preconcentration and instrumental determination was investigated and discussed. By meticulous control of experimental conditions, limits of detection for these two elements as low as sub-ng/g can be achieved. The method was applied to the determination of phosphorus and arsenic in a commercially available trichlorosilane sample.     

Electrothermal vaporization inductively coupled plasma mass spectrometry for the determination of trace amount of lanthanides and yttrium in soil with polytetrafluroethylene emulsion as a chemical modifier

A method of electrothermal vaporization inductively coupled plasma mass spectrometry (ETV-ICP-MS) for the determination of trace lanthanides and yttrium in soil samples with a polytetrafluorethylene (PTFE) emulsion as chemical modifier to promote the vaporization of the analytes from the graphite furnace was developed in this paper. The analytical characteristics, spectral interference and matrix effect of the analytical method were evaluated and critically compared with those of pneumatic nebulization inductively coupled plasma mass spectrometry (PN-ICP-MS). Under the optimized operation conditions, the relative detection limits of lanthanides (La-Lu) and yttrium for ETV-ICP-MS and PN-ICP-MS were 0.4-20 ng l⁻¹ and 1.0-21 ng l⁻¹, respectively, the absolute detection limits for ETV-ICP-MS were 4-200 fg, which were improved by 1-2 orders of magnitude compared with PN-ICP-MS. While the analytical precision of ETV-ICP-MS is worse than that of PN-ICP-MS, with the R.S.D.s (%) of 4.1-10% for the former and 2.9-7.8% for the latter. Regarding to the matrix effect, both conventional method and stepwise dilution method were employed to observe the effect of matrix and the very similar results were obtained. It was found that the highest tolerance concentration of the matrix is 1000 mg l⁻¹ and 800 mg l⁻¹ for ETV-ICP-MS and PN-ICP-MS, respectively. To assess the accuracy, the proposed method was applied to the determination of trace lanthanides and yttrium in three different soil standard reference materials and one soil sample, and the determined values are in good agreement with the certified values or reference values.     

Determination of volatile elements in biological materials by isotopic dilution ETV-ICP-MS after dissolution with tetramethylammonium hydroxide or acid digestion

Isotopic dilution for the determination of Ag, Cd, Hg, Pb and Tl in biological materials by ETV-ICP-MS is proposed. The sample was simply dissolved with tetramethylammonium hydroxide (TMAH) or acid digested in a microwave furnace, with an on line matrix separation. When the dissolution was employed, Ir was used as a chemical modifier for Hg and Pb and Pd was used for Cd and Tl. No modifier was used for Ag. The pyrolysis temperatures were taken from pyrolysis temperature curves. The on line preconcentration was performed in a flow injection system with solenoid valves and was based on the analyte complexation with ammonium diethyldithiophosphate and sorption of the complexes on C(18) bonded to silica gel in a minicolumn. For the digested sample submitted to the analyte preconcentration procedure, a modifier, Ir, was only used for Hg. For the other analytes, since a low pyrolysis temperature, 300 degrees C, was employed, no modifier was added. The isotopic dilution calibration was applied to two certified materials, bovine liver and dog fish muscle, dissolved with TMAH or acid digested, and to another two certified materials, corn bran and rice flour, acid digested and submitted to analyte preconcentration. The obtained concentration values agree with the certified ones, showing that this calibration procedure leads to accurate results in the determination of low concentrations of volatile elements. Due to simplicity, the dissolution with TMAH is very attractive.     

Microhomogeneity assessments using ultrasonic slurry sampling coupled with electrothermal vaporization isotope dilution inductively coupled plasma mass spectrometry

Ultrasonic slurry sampling electrothermal vaporization inductively coupled plasma mass spectrometry (USS-ETV-ICP-MS) is a very powerful technique for the direct analysis of solid materials prepared as slurries. The use of isotope dilution USS-ETV-ICP-MS (USS-ETV-ID-ICP-MS) for micro-homogeneity characterization studies of powdered reference materials based on elemental analyses, was investigated. Slurry analysis conditions were optimized taking into consideration density, particle size, analyte extraction, slurry mixing, analyte transport and sampling depth. Slurries were prepared using 1–20 mg of material and adding 1.0 ml of 5% nitric acid diluent containing 0.005% Triton X-100®. Three reference materials were analyzed (RM 8431a Mixed Diet, SRM 1548a Typical Diet and SRM 2709 San Joaquin Soil). Cu and Ni were determined in each material and Fe was also determined in RM 8431a Mixed Diet. ETV conditions were optimized and the benefit of using Pd as a carrier to enhance transport, combined with oxygen ashing was demonstrated. The accuracy of the method was verified by comparing analytical results with certified values. The precision of the method was demonstrated by comparing R.S.D.'s for slurry samples and aqueous standards and elemental ‘homogeneity’ was quantified based on the slurry sampling variability. The representative sample mass analyzed was calculated taking into consideration extraction of analyte into the liquid phase of the slurry. Representative sample masses of approximately 4 mg of RM 8431a provided slurry sampling variabilities of 10% or less for Cu, Fe and Ni. Representative sample masses of approximately 10 mg of SRM 1548a provided slurry sampling variabilities of approximately 10% for Cu and Ni. Representative sample masses of approximately 0.3 mg of SRM 2709 resulted in total analytical variabilities of less than 7%, highlighting the fact that the San Joaquin Soil is clearly the most homogeneous of the materials characterized.     

Chromatographic analysis of sagebrush monoterpenes in blood plasma

An analytical method is required for the analysis of monoterpenes in animal plasma to support a pharmacokinetic study. Monoterpenes common to sagebrush are extracted from sheep plasma by employing solid-phase extraction (SPE), followed by analysis of the extracts by gas chromatography with flame ionization detection. The analytes are quantitated versus an external standard and by comparison with a surrogate standard added to the sample prior to extraction. In addition to comparing the two quantitative methods, the storage stability of the analytes in plasma and SPE columns is evaluated. Both methods employed for quantitation yield precision suitable for pharmacokinetic studies. However, determination of monoterpenes residues versus external standards produces improved accuracy as compared with use of the surrogate standard. Some analyte loss is observed from plasma samples stored for five weeks at -12 degrees C. However, storage of extracts on the SPE columns affords excellent stability.     

Rapid and sensitive determination of radiocesium (Cs-135, Cs-137) in the presence of excess barium by electrothermal vaporization-inductively coupled plasma-mass spectrometry (ETV-ICP-MS) with potassium thiocyanate as modifier

An electrothermal vaporization-inductively coupled plasma-mass spectrometric (ETV-ICP-MS) method based on selective volatilization of cesium with KSCN as modifier has been developed for determination of radiocesium, i.e. 135Cs and 137Cs, in the presence of isobaric barium. A 10,000 times excess of barium, which was volatilized at a temperature of 1,100 degrees C, resulted only in a 1% signal increase in the signal of mass 135 amu. The recommended concentration of KSCN is 0.3 mM, and pretreatment and volatilization temperatures are 400 degrees C and 1,100 degrees C, respectively. A ramp time of 1 s is recommeded for the volatilization step. The achieved limit of detection for 135Cs is 0.2 pg/mL (10 microBq/mL) and 4 fg (0.2 microBq) absolute for a sample volume of 20 microL. This means a limit of detection for 137Cs of 0.2 pg/mL (0.6 Bq/mL) and of 4 fg (0.01 Bq) absolute. Signal variations of 135Cs and 137Cs, respectively, in spiked samples with various matrices were investigated.     

Direct analysis of plasma samples for drug discovery compounds using mixed-function column liquid chromatography tandem mass spectrometry

A sensitive, efficient, high throughput, direct injection bioanalytical method based on a single column and high-performance liquid chromatography (HPLC) with tandem mass spectrometry (MS/MS) was developed for pharmacokinetic analysis of early drug discovery compounds in plasma samples. After mixing with a working solution containing an internal standard each plasma sample was directly injected into a polymer-coated mixed-function column for sample cleanup, enrichment and chromatographic separation. The stationary phase incorporates hydrophilic polyoxyethylene groups and hydrophobic groups to the polymer-coated silica. This allows proteins and macromolecules to pass through the column due to restricted access to the surface of the packing while retaining the drug molecules on the bonded hydrophobic phase. The analytes retained in the column with a largely aqueous liquid mobile phase were then chemically separated by switching to a strong organic mobile phase. The column effluent was diverted from waste to the mass spectrometer for analyte detection. Within 200 plasma sample injections the response ratio (analyte vs. internal standard, %CV = 4.6) and the retention times for analyte and internal standard were found consistent and no column deterioration was observed. The recoveries of test compound in various plasma samples were greater than 90%. The total analysis time was 相似文献   

Particle sample introduction system for inductively coupled plasma–atomic emission spectrometry

Development and characterization of a new, relatively inexpensive, computer-controlled, particle sample introduction (PSI) system for programmable delivery of small amounts of diluted powdered samples into an inductively coupled plasma (ICP) and measurement by atomic emission spectrometry (AES) is described. The PSI was developed for use with non-hygroscopic particles, in particular those with a particle weight in the ng range (i.e., with a diameter in low μm-range) and for solids that can be converted to a powder (i.e., a collection of particles). In this first report on PSI–ICP–AES, linearity of calibration curves and plasma loading concerns were addressed using three modes of operation. In the first mode, the PSI operated similar to a nebulizer and it delivered to the plasma for a period of 5–10 s a relatively constant amount of particles diluted with graphite. In the second mode, the PSI delivered to the plasma a small “puff” of a diluted sample, thus generating a transient, time-domain signal with duration of about a second. In the third mode, an even smaller “puff” was delivered to the plasma and, using high-speed data acquisition (in the kHz range), time-resolved emission signals from individual, μm-diameter and ng-weight particles were observed. Thus, the PSI can also be thought of as a nano-particle (i.e., ng rather than nm) sample introduction system. Similarly, the high-speed, wide-bandwidth single-channel time-resolved data acquisition mode enabled the determination of particle-size distribution. In addition, a dual-channel (or dual-element) mode enabled homogeneity studies on a per-individual-particle basis. In all modes, linear calibration curves were obtained (provided that plasma loading was avoided). Per-cent relative standard deviation ranged between 3.1% and 4.2% for Ni in certified reference materials but was as high as 50% for heterogeneous soil samples. Tungsten emission signals from refractory tungsten carbide powders were enhanced using mixed gases and by modifying the chemical environment of the ICP using SF₆. Furthermore, when coupled with high-speed data acquisition, PSI brought unique capabilities to ICP–AES for homogeneity studies from individual ng-weight particles and for the determination of particle size distributions. Overall, it was concluded that PSI is an attractive alternative to powder sample introduction systems described in the literature.     

Automated liquid chromatographic determination of ranitidine in microliter samples of rat plasma

An improved high-performance liquid chromatographic method with UV detection at 313 nm has been developed for quantitation of ranitidine in 100 microliter of rat plasma over the range 25 to 1000 ng/ml. To each sample were added the internal standard (metiamide) and 2 M NaOH. After dichloromethane extraction, the nitrogen-dried extracts were reconstituted in the mobile phase of 0.01 M phosphate buffer-triethylamine-methanol-water (530:5:390:75 v/v). Chromatography on mu Bondapak C18 with quantitation by peak height ratios showed an analyte recovery of 97%; a limit of detection of 10 ng/ml; a precision of 1-10% and an accuracy of 1-5%. About 90 samples can be processed in 24 h.     

Direct screening and confirmation of priority volatile organic pollutants in drinking water

A screening tool was proposed for the rapid detection of eight priority volatile organic pollutants according to European standards in drinking water. The method is based on the direct coupling of a headspace sampler with a mass spectrometer, using a chromatographic column heated to 175 degrees C as an interface. The water sample was subjected to the headspace extraction process and the volatile fraction was introduced directly into the mass spectrometer, without prior chromatographic separation, achieving low detection limits (0.6-1.2 ng/ml) for all compounds. The mass spectrum resulting from the simultaneous ionization and fragmentation of the mixture of molecules constitutes the volatile profile of each sample. An appropriate chemometric treatment of these signals permitted them to be classified, on the basis of their volatile composition, as contaminated or uncontaminated with respect to the legally established concentration levels for these compounds in drinking water, and providing no false negatives. A conventional confirmation method was carried out to analyze positive water samples by using the same instrumental setup as in the screening method, but using an appropriate temperature program in the chromatographic column to separate, identify and quantify each analyte.     

超高效液相色谱/静电场轨道阱高分辨质谱法同时测定塑料食品接触材料中光稳定剂和抗氧化剂的特定迁移量

建立了超高效液相色谱/静电场轨道阱高分辨质谱同时测定塑料食品接触材料中多种光稳定剂和抗氧化剂特定迁移量的方法。采用30 g/L乙酸、体积分数分别为10%、20%、50%的乙醇和油类模拟物(异辛烷)这5种食品模拟物对塑料食品接触材料进行处理,对处理液进行超高效液相色谱/静电场轨道阱高分辨质谱分析,外标法定量。该方法测定的40种目标化合物在相应的范围内均具有良好的线性关系,相关系数均大于0.998,定量限为0.01~1.00μg/L。考察了上述5种食品模拟物中光稳定剂和抗氧化剂的特定迁移量,平均加标回收率为81.46%~94.53%,相对标准偏差为3.25%~9.99%。应用该方法对市售塑料食品接触材料进行了测定,结果在部分样品中检出了不同含量的光稳定剂和抗氧化剂。该方法灵敏度高,定量限低,满足塑料食品接触材料中光稳定剂和抗氧化剂特定迁移量的检测要求。