介质阻挡放电等离子体与吸附在CuZSM-5上的NO或NO/O2的相互作用

采用吸附和程序升温脱附(TPD)技术研究了介质阻挡放电等离子体对CuZSM-5催化剂上吸附的氮氧化物作用. 实验表明, 介质阻挡放电等离子体使催化剂表面吸附的NO及Cu活性位上吸附的NOx物种脱附, 并引发表面化学反应生成新的氮氧化物. 对于NO/N2体系, 介质阻挡放电等离子体与吸附在CuZSM-5上NO作用, 主要生成N2O和O2. 在富氧体系NO/O2/N2, 则生成较大量的N2O、NO2和NO. 等离子体预处理活性下降的CuZSM-5, 可明显提高其催化分解NO活性. 对比有或无介质阻挡放电等离子体预处理NO或NO/O2饱和吸附的CuZSM-5上的NO-TPD结果表明, 等离子体提高催化剂活性的原因与其使催化剂Cu活性位上吸附的NOx物种脱附有关.     

介质阻挡放电等离子体与吸附在CuZSM-5上的NO或NO/O2的相互作用

采用吸附和程序升温脱附(TPD)技术研究了介质阻挡放电等离子体对CuZSM-5催化剂上吸附的氮氧化物作用.实验表明,介质阻挡放电等离子体使催化剂表面吸附的NO及Cu活性位上吸附的NOx物种脱附,并引发表面化学反应生成新的氮氧化物.对于NO/N2体系,介质阻挡放电等离子体与吸附在CuZSM-5上NO作用,主要生成N2O和O2.在富氧体系NO/O2/N2,则生成较大量的N2O、NO2和NO.等离子体预处理活性下降的CuZSM-5,可明显提高其催化分解NO活性.对比有或无介质阻挡放电等离子体预处理NO或NO/O2饱和吸附的CuZSM-5上的NO-TPD结果表明,等离子体提高催化剂活性的原因与其使催化剂Cu活性位上吸附的NOx物种脱附有关.     

NO_x分子在[Ag]-MAPO-5(M=Si,Ti)分子筛中的吸附

采用密度泛函理论(DFT)研究了银离子交换的硅磷酸铝([Ag]-SAPO-5)和钛磷酸铝([Ag]-TAPO-5)分子筛结构及其对NOx分子的吸附,获得吸附复合物的平衡几何结构参数和吸附能.结果表明,NOx分子以η1-N模式吸附在[Ag]-SAPO-5和[Ag]-TAPO-5分子筛中的结构更稳定,其吸附作用强度的次序为NO2NON2O.[Ag]-SAPO-5和[Ag]-TAPO-5对NO和NO2分子的活化程度要比N2O大.相比[Ag]-AlMOR,[Ag]-SAPO-5和[Ag]-TAPO-5对NOx分子的活化程度较大.还对[Ag]-SAPO-5和[Ag]-TAPO-5分子筛的抗硫、抗水及抗氧化性能进行了研究和分析.另外,通过自然键轨道(NBO)计算,分析了NOx分子与平衡离子Ag+之间的作用机理.     

用密度泛函理论研究NO在H-ZSM-5分子筛不同酸性位的吸附

利用密度泛函理论(DFT),基于7T簇模型,在B3LYP/6-31G(d,p)水平上研究了NO分子在H-ZSM-5分子筛孔道中α,β,γ酸性位的吸附.在计算过程中,首先对H-ZSM-5的α,β,γ酸性位进行优化计算,然后对NO分子η1-N和η1-O两种吸附模式的红外光谱和吸附能进行计算.计算结果表明,NO分子以η1-N模式吸附于H-ZSM-5分子筛酸性位上,不同酸性位对NO分子的吸附能力排序为:α酸性位>β酸性位>γ酸性位.此外,H-ZSM-5分子筛直型孔道更有利于NO分子的吸附和扩散,因而可更有效地促进NO分子催化分解反应的进行.     

低温等离子体协助B_2O_3/γ-Al_2O_3 选择催化还原NO(英文)

研究了低温等离子体协助催化条件下甲烷选择性催化还原NO反应(SCR).反应气体经等离子体活化后,生成NO2,HCHO,CH3NO和CH3NO2等活性更高的中间产物.程序升温表面反应表明,这些中间产物可在等离子体后置催化装置上进一步反应,从而使NOx还原为N2.在考察的一系列催化剂(包括γ-Al2O3,Ag/γ-Al2O3,B2O3/γ-Al2O3,Ga2O3/γ-Al2O3,In2O3/γ-Al2O3等)中,B2O3/γ-Al2O3表现出最好的催化活性.当反应温度为300oC时,NOx转化率达到最高.与γ-Al2O3催化剂相比,在10wt%B2O3/γ-Al2O3催化剂上,300oC时,NOx转化为N2的转化率从33.4%提高至51.0%.催化剂的酸性对于经等离子体活化后的反应气体在催化剂上的SCR反应起到重要作用.同时,催化剂上吸附态NOx对于NOx的转化也起到一定作用.     

预吸附氧对NO在Pt(110)表面吸附和分解的影响

 利用程序升温反应谱、X射线光电子能谱和高分辨电子能量损失谱研究了NO在清洁和预吸附氧的Pt(110)表面的吸附和分解. 在清洁的Pt(110)表面,室温下低覆盖度时NO以桥式吸附为主,高覆盖度时NO以线式吸附为主. 加热过程中部分NO(主要是桥式吸附物种)分解,生成N2和N2O. 室温下O2在Pt(110)表面发生解离吸附. Pt(110)表面预吸附氧会抑制桥式吸附NO的生成,并导致其脱附温度降低40 K. 降低脱附温度有利于桥式吸附NO的分子脱附,从而抑制分解反应. 这些结果从表面化学的角度合理地解释了铂催化剂在富氧条件下对NO分解能力的降低.     

低温等离子体协助B2O3/γ-Al2O3 选择催化还原NO（英文）

研究了低温等离子体协助催化条件下甲烷选择性催化还原NO反应(SCR).反应气体经等离子体活化后,生成NO2,HCHO,CH3NO和CH3NO2等活性更高的中间产物.程序升温表面反应表明,这些中间产物可在等离子体后置催化装置上进一步反应,从而使NOx还原为N2.在考察的一系列催化剂(包括γ-Al2O3,Ag/γ-Al2O3,B2O3/γ-Al2O3,Ga2O3/γ-Al2O3,In2O3/γ-Al2O3等)中,B2O3/γ-Al2O3表现出最好的催化活性.当反应温度为300oC时,NOx转化率达到最高.与γ-Al2O3催化剂相比,在10wt%B2O3/γ-Al2O3催化剂上,300oC时,NOx转化为N2的转化率从33.4%提高至51.0%.催化剂的酸性对于经等离子体活化后的反应气体在催化剂上的SCR反应起到重要作用.同时,催化剂上吸附态NOx对于NOx的转化也起到一定作用.     

助剂对Pd/γ-Al2 O3催化剂上NO选择催化还原的影响

研究了含氧条件下钯催化剂上进行丙烯选择催化还原NO的反应,考察浸渍法制备的Pd/γ-Al2O3催化剂中加入碱(土)金属或稀土氧化物助剂对NO转化率的影响,并对催化剂进行了XRD表征及在氧化气氛中饱和吸附NO后的TPD研究.结果表明,助剂CeO2、 Li2O能较大幅度提高催化剂的低温活性,使NO的最高转化率增加1～3.5倍.Pd/CeO2-Al2O3、 Pd/Li2O-Al2O3催化剂有较高的Pd分散度及较强的NO解离吸附能力.并讨论了NO、 N2O、 NO2-和NO3-等吸附态物种在催化剂表面的形成及脱附特性对催化剂选择催化还原NO性能的影响.     

NOx分子在[Ag]-AlMOR分子筛中的吸附

采用Dmol3程序中密度泛函理论(DFT)的广义梯度方法GGA/BLYP和DND基组研究了银离子交换的丝光沸石([Ag]-AlMOR)结构及其对NOx分子吸附性能的影响, 获得吸附复合物的平衡几何结构参数、吸附能以及红外振动频率等数据. 结果表明, NOx分子与丝光沸石间的主要作用力为NOx分子中的氮(或氧)原子上的孤对电子和Ag+间的静电作用力. 吸附能数据表明, NOx分子以η1-N模式吸附在[Ag]-AlMOR分子筛中的结构更稳定; 在η1-N模式中, NOx分子吸附作用强度的次序为NO>NO2>N2O. 红外振动频率结果表明, 吸附态NOx分子中N—O和N—N键伸缩振动频率的位移趋势与N—O和N—N 键变化规律基本相一致. 另外, 对[Ag]-AlMOR分子筛的抗硫、抗水及抗氧化性能也进行了研究和分析.     

NO 和 NO2 在 V2O5/AC 催化剂表面的反应行为

 采用程序升温脱附、在线质谱和原位漫反射红外光谱等手段, 比较了 NO 和 NO2 在 V2O5 及 V2O5/AC 催化剂表面的选择催化还原 (SCR) 反应行为. 结果表明, 氨以质子态 NH4+和共价态 NH3 分子两种形态吸附于纯 V2O5 表面, V=O 为氨的主要吸附活性位. 无氧状态下, NO 和 NO2 皆可与吸附于 V2O5 表面的 NH3 反应, 并且 NO2 与吸附态 NH3 的反应活性高于 NO. 但在 V2O5/AC 催化剂表面, 同样在无氧条件下, NO 几乎不与吸附态 NH3 反应, 而 NO2 却可以反应并生成 N2. 在 V2O5/AC 表面, NO 很容易被气相 O2 氧化为 NO2, 然后参与 SCR 反应. 可见, NO2 是 NO 在 V2O5/AC 表面发生 SCR 反应的中间体.     

新型亲核NO供体Diazeniumdiolate及其靶向性控释材料

新型亲核NO供体diazeniumdiolate独特的化学结构和性质,使其成为目前NO供体研究的一个热点.要使其成为更有效的药物,它的靶向性和控释性能是当前研究的重点,减小亲核试剂(多胺)的细胞毒性和亚硝胺的生成是研究的难点.本文对增强靶向性释放所采取的三个措施(聚合物控释、特定酶代谢释放和光降解释放)的近十几年国外的研究情况进行了综述.     

Role of NO and NO synthases in oncogenesis

The review focuses on the role of NO and NO synthases in the signaling pathways responsible for the occurrence and development of leukemias. Some classes of inhibitors of different NO synthase isoforms that exhibit cytotoxic activity against leukemia cells are described.     

Electron transfer NO 2 + +NO→N02+NO+ in aromatic nitration

A simple model for computing the electron transfer rate constant of a cross-reaction has been proposed in the framework of semiclassical theory and employed to investigate the electron transfer system NO ₂ ⁺ /NO. The encounter complex of electron transfer NO ₂ ⁺ +NO→N0₂+NO⁺ has been optimized at the level of UHF/6-31G. In the construction of diabatic potential energy surfaces the linear coordinate was used and the kinetic quantities, such as the activation energies and the electron transfer matrix elements, have been obtained. For comparison, the related selfexchange reactlon systems NO ₂ ⁺ /NO₂ and NO⁺/NO were kinetically investigated. The calculated activation energies for the electron transfer reactions of systems NO ₂ ⁺ /NO, NO ₂ ⁺ /NO₂, and NO⁺/NO are 81.4, 128.8, and 39.8 kJ.mol^-1, respectively. With the solvent effect taken into account, the contribution of solvent reorganization to the activation energy has been estimated according to the geometric parameters of the transition states. The obtained rate constants show that the activity of NO ₂ ⁺ as an oxidizing reagent in the aromatic nitration will be greatly decreased due to a high activation barrier contributed mainly from the change of bond angle ONO.     

Reactions of isopropylperoxy radicals with NO and NO2

The rate constants for the reactions have been measured directly by flash photolysis and kinetic spectroscopy. At room temperature, k₃ = (3.4 ± 0.1) × 10⁹ L/mol·s, independent of pressure in the range of 55–400 torr, and k₆ = (2.1 ± 0.2) × 10⁹ L/mol·s.     

负载Pt,Pd催化剂上NO—TPD和NO催化还原性能

负载Ｐｔ、Ｐｄ催化剂上ＮＯ－ＴＰＤ和ＮＯ催化还原性能１）钟依均（浙江师范大学化学系金华３２１００４）罗孟飞周碧袁贤鑫（杭州大学催化研究所杭州３１００２８）关键词负载Ｐｔ、Ｐｄ催化剂ＮＯ－ＴＰＤＣＯ－ＮＯ反应分类号Ｏ６４３．３２氮氧化物（ＮＯｘ）污染是...     

Studies on NO releasing from PCU grafted with endogenous NO donors

Films of PCUs grafted with L ‐nitrosocysteine (L ‐CySNO) were successfully prepared in the presence of 3‐aminopropyltriethoxysilane (APTES). The final products (L ‐CySNO‐grafted PCU) were characterized with ATR‐FTIR, SEM, XPS, and tensile strength measurement. Tensile strength of the L ‐CySNO‐grafted PCU was decreased compared to that of non‐grafted PCU. In vitro NO release from the produced films was obtained by using ascorbic acid (Vc) as reducing agent, and the velocity of the released NO was measured by the Griess assay. The effects of temperature, molecular weight of polycarbonate diols (PCN), and thickness of the films on in vitro NO release were investigated in detail. It was found that with the increase of temperature, the velocity of NO release increased, whereas with the increase of molecular weight of polycarbonate diols, the velocity decreased. However, thickness of PCU films has no effect on NO release. The results of cytotoxicity test and hemolytic test indicate that blood compatibility and biocompatibility of the grafted PCU are better than those of the synthesized PCU. Copyright © 2009 John Wiley & Sons, Ltd.     

Kinetics of the reactions of NCO with NO and NO2

The rate coefficients of the reactions of NCO radicals with NO and NO₂: (1) NCO + NO → products (293–836 K) and : (2) NCO + NO₂ → products (294–774 K) were measured by means of laser photolysis and laser induced fluorescence technique in the indicated temperature ranges. NCO radicals were produced from the reaction of CN, from photodissociation of ICN or BrCN, with O₂. The concentration of NCO was monitored with a dye laser set at 414.95 nm. We determined k₁ = 1.73 × 10^?5 T^?2.01 exp(?470/T) cm³ molecule^?1 s^?1 that agrees with published results at room temperature and confirms the temperature dependence of an early report. A non-Arrhenius negative temperature dependence of k₂ was observed in this work that agrees satisfactorily with results for a shock tube¹⁸ near 1250 K. We obtained k₂ = 6.4 × 10^?10 T^?0.646 exp(164/T) cm³ molecule^?1 s^?1 for 1250 K ≥ T ≥ 294 K by combining data of these two measurements. Our result at 294 K and the temperature dependence disagree with results of two previous investigations. © 1995 John Wiley & Sons, Inc.