Thermally reversible pluronic/heparin nanocapsules exhibiting 1000-fold volume transition

Novel Pluronic/heparin composite nanocapsules that exhibit a thermally responsible swelling and deswelling behavior were synthesized. Pluronic F-127 preactivated with p-nitrophenyl chloroformate at its two terminal hydroxyl groups was dissolved in a methylene chloride phase. The organic phase was dispersed in an aqueous phase containing heparin. At an organic/aqueous interface, Pluronic-cross-linked heparin nanocapsules were produced. They exhibited a 1000-fold volume transition (ca. 336 nm at 25 degrees C; ca. 32 nm at 37 degrees C), and a reversible swelling and deswelling behavior when the temperature was cycled between 20 and 37 degrees C. The reversible volume transition of Pluronic nanocapsules was caused by micellization and demicellization of cross-linked Pluronic polymer chains within the nanocapsule structure in response to temperature. The morphological characters were investigated with transmission electron microscopy and small angle neutron scattering. Pluronic/heparin nanocapsules had an aqueous fluid-filled hollow interior with a surrounding shell layer below the critical temperature, but they became a collapsed core/shell structure similar to that of Pluronic micelles above it.     

Synthesis and applications of shell cross-linked thermoresponsive hybrid micelles based on poly(N-isopropylacrylamide-co-3-(trimethoxysilyl)propyl methacrylate)-b-poly(methyl methacrylate)

Shell cross-linked (SCL) thermoresponsive hybrid micelles consisting of a cross-linked thermoresponsive hybrid hydrophilic shell and a hydrophobic core domain were synthesized from poly(N-isopropylacrylamide-co-3- (trimethoxysilyl)propyl methacrylate)-b-polymethyl methacrylate (P(NIPAAm-co-MPMA)-b-PMMA) amphiphilic block copolymers. Transmission electron microscopy (TEM) images showed that the SCL micelles formed regularly globular nanoparticles. The SCL micelles showed reversible dispersion/aggregation in response to temperature cycles through an outer polymer shell lower critical solution temperature (LCST) for PNIPAAm at around 33 degrees C, observed by turbidity measurements and dynamic light scattering (DLS). The drug loading and in vitro drug release properties of the SCL micelles bearing a silica-reinforced PNIPAAm shell were further studied, which showed that the SCL micelles exhibited a much improved entrapment efficiency (EE) as well as a slower release rate which allowed the entrapped molecules to be slowly released over a much longer period of time as compared with pure PNIPAAm-b-PMMA micelles.     

Double hydrophilic block copolymer monolayer protected hybrid gold nanoparticles and their shell cross-linking

This paper describes the syntheses of core/shell gold nanoparticles stabilized with a monolayer of double hydrophilic block copolymer and their stimuli responsiveness before and after shell cross-linking. The hybrid nanoparticles consist of gold core, cross-linkable poly(2-(dimethylamino)ethyl methacrylate) (PDMA) inner shell, and poly(ethylene oxide) (PEO) corona. First, diblock copolymer PEO-b-PDMA was prepared via the reversible addition-fragmentation chain transfer (RAFT) technique using a PEO-based macroRAFT agent. The dithioester end group of PEO-b-PDMA diblock copolymer was reduced to a thiol end group. The obtained PEO-b-PDMA-SH was then used to prepare diblock copolymer stabilized gold nanoparticles by the "grafting-to" approach. 1,2-Bis(2-iodoethoxy)ethane (BIEE) was utilized to selectively cross-link the PDMA residues in the inner shell. The stimuli responsiveness and colloidal stability of core/shell gold nanoparticles before and after shell cross-linking were characterized by laser light scattering (LLS), UV-vis transmittance, and transmission electron microscopy (TEM). At pH 9, the average hydrodynamic radius Rh of non-cross-linked hybrid gold nanoparticles starts to increase above 35 degrees C due to the lower critical solution temperature (LCST) phase behavior of the PDMA blocks in the inner shell. In contrast, Rh of the shell cross-linked gold nanoparticles were essentially independent of temperature. Core/shell gold nanoparticles before and after shell cross-linking exhibit reversible swelling on varying the solution pH. Compared to non-cross-linked core/shell gold nanoparticles, shell cross-linking of the hybrid gold nanoparticles leads to permanent core/shell nanostructures with much higher colloidal stability and physically isolates the gold core from the external environment.     

Shell cross-linked stearic acid grafted chitosan oligosaccharide self-aggregated micelles for controlled release of paclitaxel

Stearic acid grafted chitosan oligosaccharide (CSO-SA) with different degree of amino substitution (SD) was synthesized by 1-ethyl-3-(3-dimethylaminopropyl) carbodiimide (EDC)-mediated coupling reaction. The critical micelle concentration (CMC) of CSO-SA with different SD was about 0.06, 0.04, 0.01 mg/ml, respectively. With the increase of micelle concentration, the micelle size decreased, and the zeta potential increased. On the other hand, with the increase of SD of CSO-SA, the micelle size and zeta potential decreased due to the increased hydrophobic interaction of SA and the reduced free amino groups. To increase the stability of the micelle in vivo and controll drug release, the shells of micelles were cross-linked by glutaraldehyde. By controlling the molar ratio of CSO-SA to glutaraldehyde, the cross-linking of intra-micelle could be reached, and the nanoparticle with smaller size than that of its initial micelle was obtained. Paclitaxel was then used as model drug to incorporate into the micelles, and the surfaces of the micelles were further cross-linked by glutaraldehyde to form drug loaded and shell cross-linked nanoparticles. The effects of drug loading, SD of CSO-SA and cross-link degree on the size, zeta potential, drug entrapment efficiency and in vitro drug release behavior of micelles and its cross-linked nanoparticles were investigated. The higher drug entrapment efficiencies (above 94%) were observed in all case. The charged amounts of drug did not affect the drug release behavior. The drug release rate decreased with the increase of SD of CSO-SA and cross-link degree.     

Thermosensitive core-shell particles as carrier systems for metallic nanoparticles

We present a new system that allows us to modulate the catalytic activity of metal nanoparticles (Ag) by a thermodynamic transition that takes place within the carrier system. Thermosensitive core-shell particles have been used as the carrier system in which the core consists of poly(styrene) (PS), whereas the shell consists of a poly(N-isopropylacrylamide) (PNIPA) network cross-linked by N,N'-methylenebisacrylamide (BIS). Immersed in water, the shell of these particles is swollen. Heating the suspension above 32 degrees C leads to a volume transition within the shell that is followed by a marked shrinking of the network of the shell. The maximum degree of swelling can be adjusted by the degree of cross-linking. Silver nanoparticles with diameters ranging from 6.5 to 8.5 nm have been embedded into thermosensitive PNIPA networks with different cross-linking densities. The Ag nanoparticles do not influence the swelling and the shrinking of the network in the shell. The surface plasmon absorption band of the nanoparticles is shifted to higher wavelengths with temperature. This is traced back to the varying distance of the nanoparticles caused by the swelling and the shrinking of the shell. The catalytic activity is investigated by monitoring photometrically the reduction of 4-nitrophenol by an excess of NaBH4 in the presence of the silver nanocomposite particles. The rate constant kapp was found to be strictly proportional to the total surface of the nanoparticles in the system. Moreover, kapp is first decreasing with increasing temperature when approaching the volume transition. This is due to the strong shrinking of the network. Only at temperatures above the volume transition is the normal Arrhenius-type dependence of kapp found again. In this way, catalytic activity of the metal nanoparticles enclosed in a "nanoreactor" can be modulated by volume transition over a wide range.     

Synthesis and characterization of shell cross-linked micelles with hydroxy-functional coronas: a pragmatic alternative to dendrimers?

Shell cross-linked (SCL) micelles with hydroxy-functional coronas have been constructed in aqueous solution by exploiting the micellar self-assembly behavior of a new thermoresponsive ABC triblock copolymer. This copolymer was prepared via atom transfer radical polymerization in a convenient one-pot synthesis and comprised a thermoresponsive core-forming poly(propylene oxide) (PPO) block, a cross-linkable central poly(2-(dimethylamino)ethyl methacrylate) (DMA) block, and a hydroxy-functional outer block based on poly(glycerol monomethacrylate) (GMA). DMF GPC analysis confirmed a unimodal molecular weight distribution for the PPO-PDMA-PGMA triblock copolymer precursor, with an M(n) of 12 100 and a polydispersity of approximately 1.26. This copolymer dissolved molecularly in aqueous solution at 5 degrees C but formed micelles with hydroxy-functional coronas above a critical micelle temperature of around 12 degrees C, which corresponded closely to the cloud point of the PPO macroinitiator. Cross-linking of the DMA residues using 1,2-bis(2-iodoethoxy)ethane produced SCL micelles that remained intact at 5 degrees C, i.e., below the cloud point of the core-forming PPO block. Dynamic light scattering studies confirmed that the SCL micelle diameter could be varied depending on the temperature employed for cross-linking: smaller, more compact SCL micelles were formed at higher temperatures, as expected. Since cross-linking involved quaternization of the DMA residues, the SCL micelles acquired cationic surface charge as judged by aqueous electrophoresis studies. These cationic SCL micelles were adsorbed onto near-monodisperse anionic silica sols, which were used as a model colloidal substrate. Thermogravimetric analyses indicated a SCL micelle mass loading of 2.5-4.4%, depending on the silica sol diameter and the initial micelle concentration. Aqueous electrophoresis measurements confirmed that surface charge reversal occurred after adsorption of the SCL micelles, and scanning electron microscopy studies revealed a uniform coating of SCL micelles on the silica particles.     

Synthesis and Stabilization of Gold Nanoparticles in Reverse Micelles of Aerosol OT and Triton X-100

Mechanisms of the formation and stabilization of gold nanoparticles in reverse micelles of micro-emulsions based on Triton X-100 (TX-100) and Aerosol OT (AOT) are studied. The instability of AOT-based microemulsions is shown to be caused by the oxidative degradation of gold nanoparticles in micelle water pools. Methods are proposed for the stabilization of these microemulsions. It is revealed that the mean size of gold nanoparticles synthesized in TX-100 reverse micelles in the presence of sodium sulfite is markedly smaller than that of particles prepared in AOT reverse micelles. This is explained by the fact that gold clusters are formed in the micelle shell rather than in the water pool. In the shell, the clusters are stabilized by oxyethylene groups of TX-100 molecules.__________Translated from Kolloidnyi Zhurnal, Vol. 67, No. 4, 2005, pp. 534–540.Original Russian Text Copyright © 2005 by Spirin, Brichkin, Razumov.     

Synthesis of sodium-polystyrenesulfonate-grafted nanoparticles by core-cross-linking of block copolymer micelles

Sodium poly(styrenesulfonate)(polySSNa)-grafted polymer nanoparticles were synthesized by core-cross-linking of block copolymer micelles and subsequent chemical transformation. Block copolymers, poly(p-((1-methyl)silacyclobutyl)styrene-block-poly(neopentyl p-styrenesulfonate)s, polySBS-b-polySSPen, were synthesized by nitroxy-mediated living radical polymerization. The block copolymers formed micelles (R_h=15-23 nm, where R_h represents the hydrodynamic radius) with a polySBS core and polySSPen shell in acetone. The micelle core was cross-linked by ring-opening polymerization of silacyclobutyl groups in polySBS. Hydrolysis of the neopentyl groups provided polySSNa-grafted nanoparticles. The R_h of the particles before the hydrolysis ranged from 12 to 21 nm in acetone, while they varied to the range from 50 to 110 nm in water after the hydrolysis.     

Synthesis and characterization of core-shell microspheres with double thermosensitivity

We have synthesized doubly thermosensitive core-shell microspheres composed of chemically cross-linked poly(N-n-propyl acrylamide-co-styrene) (P(nPA-co-S)) with different styrene contents as the core and linear poly(N,N-diethyl acrylamide) (PDEA), poly(N-isopropyl acrylamide) (PiPA), or poly(N-isopropyl methacrylamide) (PiPMA) as the shells. The morphologies and swelling properties of the core and the core-shell microspheres have been studied. The P(nPA-co-S) copolymers have a similar volume phase transition temperature regardless of the styrene content, indicating a two-layer structure in the microspheres with a PS-rich inner core and a PnPA-rich outer layer resulting from soap-free emulsion polymerization in water. Upon the addition of the second shell composed of linear thermosensitive polymers, the core-shell microspheres display a two-step shrinking behavior when heated. The P(nPA-co-S) core exhibits a volume phase transition temperature at 13-15 degrees C, while the shells of PDEA, PiPA, and PiPMA have volume phase transition temperatures at 28, 32, and 42 degrees C, respectively. The core-shell microspheres are composed of three layers and possess two volume phase transition temperatures.     

Catalytic activity of supported Au nanoparticles deposited from block copolymer micelles

Quasi-ordered, highly dispersed, gold nanoclusters of tightly controlled particle size were synthesized by dip-coating substrates with gold precursors encapsulated by block-copolymer micelles. By this method, gold particles (4.8 +/- 1.3 nm) were deposited on ITO-coated glass and shown to be catalytically active for electro-oxidation of carbon monoxide. XPS confirmed the catalytically active particles were predominantly Au0; however, a large fraction existed as Au3+. Whereas bulk gold is inert, these results demonstrate that catalytically active Au nanoparticles can be derived from micelle encapsulation.     

Preparation of poly(styrene‐b‐N‐isopropylacrylamide) micelles surface‐linked with gold nanoparticles and thermo‐responsive ultraviolet–visible absorbance

Poly(styrene‐b‐N‐isopropylacrylamide) (PSt‐b‐PNIPAM) with dithiobenzoate terminal group was synthesized by reversible addition‐fragmentation‐transfer polymerization. The dithiobenzoate terminal group was converted into thiol terminal group with NaBH₄, resulting thiol‐terminated PSt‐b‐PNIPAM‐SH. After PSt‐b‐PNIPAM‐SH assembled into core‐shell micelles in aqueous solution, gold nanoparticles were in situ surface‐linked onto the micelles through the reduction of gold precursor anions with NaBH₄. Thus, temperature responsive core/shell micelles of PSt‐b‐PNIPAM surface‐linked with gold nanoparticles (PSt‐b‐PNIPAM‐Au micelles) were obtained. Transmission Electron Microscopy revealed the successful linkage of gold nanoparticles and the dependence of the number of gold nanoparticles per micelle on the molar ratio of HAuCl₄ to thiol group of PSt‐b‐PNIPAM. Dynamic Light Scattering analysis demonstrated thermo‐responsive behavior of PSt‐b‐PNIPAM‐Au micelles. Changing the temperature of PSt‐b‐PNIPAM‐Au micelles led to the shrinkage of PNIPAM shell and allowed to tune the distance between gold nanoparticles. Ultraviolet–visible (UV–vis) spectroscopy clearly showed the reversible modulation of UV–vis absorbance of PSt‐b‐PNIPAM‐Au micelles upon heating and cooling. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5156–5163, 2007     

Thermoresponsive behavior of poly(n-isopropylacrylamide) hydrogels containing gold nanostructures

We report the changes in the structure and thermoresponsive behavior of poly(N-isopropylacrylamide) (PNIPAm) hydrogels when gold nanostructures are synthesized in situ within the hydrogel matrix. Cross-linked PNIPAm hydrogels were synthesized using NIPAm and 0.00-3.50% (w/w versus NIPAm) of N,N'-methylenebisacrylamide (MBAm) and/or N,N'-cystaminebisacrylamide (CBAm) as cross-linking agents. The hydrogels were soaked in potassium tetrachloroaurate to introduce gold ions. The hydrogels containing Au3+ were then immersed in a sodium borohydride solution to reduce the gold ions. Infrared spectroscopy, UV-visible spectroscopy, and equilibrium swelling were used to examine the structural/physical differences between gels of different compositions; UV-visible spectroscopy and mass measurements were used to observe the kinetics and thermodynamics of the hydrogel volume phase transition. These studies revealed several differences in the physical characteristics and thermoresponsive behavior of hydrogels based on cross-linker identity and the presence or absence of gold nanostructures. Hydrogels with gold nanostructures and high CBAm and low MBAm content have equilibrium swelling masses 3-20 times their native analogues. In comparison, gold-containing hydrogels with high MBAm and low CBAm content have swelling masses that are equal to their native analogues. Additionally, the gold-containing PNIPAm hydrogels cross-linked with only CBAm have a deswelling temperature of approximately 40 degrees C, approximately 8 degrees C above the samples cross-linked with only MBAm. Varying the CBAm content and introducing gold enables tuning of the deswelling temperature.     

Synthesis and characterization of core–shell‐type polymeric micelles from diblock copolymers via reversible addition–fragmentation chain transfer

A method was developed to enable the formation of nanoparticles by reversible addition–fragmentation chain transfer polymerization. The thermoresponsive behavior of polymeric micelles was modified by means of micellar inner cores and an outer shell. Polymeric micelles comprising AB block copolymers of poly(N‐isopropylacrylamide) (PIPAAm) and poly(2‐hydroxyethylacrylate) (PHEA) or polystyrene (PSt) were prepared. PIPAAm‐b‐PHEA and PIPAAm‐b‐PSt block copolymers formed a core–shell micellar structure after the dialysis of the block copolymer solutions in organic solvents against water at 20 °C. Upon heating above the lower critical solution temperature (LCST), PIPAAm‐b‐PHEA micelles exhibited an abrupt increase in polarity and an abrupt decrease in rigidity sensed by pyrene. In contrast, PIPAAm‐b‐PSt micelles maintained constant values with lower polarity and higher rigidity than those of PIPAAm‐b‐PHEA micelles over the temperature range of 20–40 °C. Structural deformations produced by the change in the outer polymer shell with temperature cycles through the LCST were proposed for the PHEA core, which possessed a lower glass‐transition temperature (ca. 20 °C) than the LCST of the PIPAAm outer shell (ca. 32.5 °C), whereas the PSt core with a much higher glass‐transition temperature (ca. 100 °C) retained its structure. The nature of the hydrophobic segments composing the micelle inner core offered an important control point for thermoresponsive drug release and the drug activity of the thermoresponsive polymeric micelles. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3312–3320, 2006     

Double electron electron resonance as a method for characterization of micelles

Double electron electron resonance (DEER) is an experimental technique used to determine distance between electron spins. In this work, we show that it can be used to study the properties of micelles in solution, specifically their volume and the aggregation number. The feasibility of the method is tested on micelles of Pluronic block copolymers, PEO(x)-PPO(y)-PEO(x), built from chains of poly(ethylene oxide) (PEO), comprising the more hydrophilic corona, and a poly(propylene oxide) (PPO) block constituting the hydrophobic core. In this work, the dimensions of the hydrophobic core of micelles of Pluronic L64 (x = 13, y = 30), P123 (x = 20, y = 70), and F127 (x = 106, y = 70) and their aggregation number were studied. This was done using the spin-probe 4-hydroxy-tempo-benzoate (4HTB), which is hydrophobic and is localized in the hydrophobic core of the micelles and does not dissolve in aqueous solution. The measurements were carried out on frozen solutions, freeze quenched after equilibration at 50 degrees C. It was found that the hydrophobic core radii occupied by 4HTB in 7.5 wt % F127 and 6 wt % L64 are 4.0 +/- 0.05 and 3.8 +/- 0.1 nm, respectively, and the corresponding aggregation numbers are 57 +/- 2 and 206 +/- 14. The micelles of 6 wt % P123 were found to have a rod shape, and the addition of 4HTB at concentrations higher than 0.7 mM resulted in a phase transitioned to spherical micelles. Finally, this study also showed that the micelle structure is preserved upon rapid freezing.     

On the morphology and stability of Au nanoparticles on TiO2(110) prepared from micelle-stabilized precursors

The morphology and stability of well-ordered, nanostructured Au/TiO2(110) surfaces, prepared by deposition of Au loaded micelles on TiO2(110) substrates and subsequent oxidative removal of the polymer shell in an oxygen plasma, was investigated by noncontact AFM, SEM and XPS. The resulting arrays of Au nanoparticles (particle sizes 1-5 nm) form a nearly hexagonal pattern with well-defined interparticle distances and a narrow particle size distribution. Particle size and particle separation can be controlled independently by varying the Au loading and the block-copolymers in the micelle shell. The oxygen plasma treatment does not affect the size and distance of the Au nanoparticles; the latter are fully metallic after subsequent UHV annealing (400 degrees C). The particles are stable under typical CO oxidation reaction conditions, up to at least 200 degrees C, making these surfaces ideally suited as defined model systems for catalytic studies. Significant changes in the height distributions of the Au nanoparticles are found upon 400 degrees C annealing in O2. For adlayers with small interparticle distances, this leads to a bimodal particle size distribution, which together with the preservation of the lateral order points to Ostwald ripening.     

SANS from Pluronic P85 in d-water

Small-angle neutron scattering (SANS) has been used to investigate Pluronic P85 (EO₂₆PO₄₀EO₂₆) copolymer in deuterated water. A range of P85 fractions were measured for a wide sample temperature window. A rich phase behavior is reported. Unimers were observed below the critical micelle formation condition. At fixed P85 fraction, a number of micellar phases were observed upon increasing temperature; first spherical micelles, then cylindrical micelles, then lamellar micelles. At the highest temperature, a demixed lamellae phase was observed. Analysis of the SANS data consisted in fits to an empirical Guinier-Porod model that was appropriate for data fitting in the various phases at low P85 fractions. When the P85 fraction increased, an inter-particle structure factor was included to analyze SANS data from concentrated spherical micelles. At high P85 fractions, paracrystalline structures were observed as evidenced by an enhanced inter-particle interaction peak. A phase diagram for P85/d-water was obtained showing the various phases. Focusing on the spherical micelles phase for one sample composition, a core-shell model was used to fit SANS data and obtain sizes and scattering length densities. Using material balance equations, information such as the aggregation number (i.e., number of Pluronic macromolecules per micelle) and the number of hydration water molecules in the shell region are determined.     

Synthesis and characterisation of new shell cross-linked micelles with amine-functional coronas

Shell cross-linked (SCL) micelles with amine-functional coronas have been constructed in aqueous solution by exploiting the micellar self-assembly of new thermo-responsive ABC triblock copolymers. These copolymers were prepared via atom transfer radical polymerisation (ATRP) in convenient one-pot syntheses and comprised a thermo-responsive core-forming poly(propylene oxide) [PPO] block, a cross-linkable central poly(glycerol monomethacrylate) [GMA] block and an amine-functional outer block based on either poly(2-(dimethylamino)ethyl methacrylate) [DMA] or poly([2-(methacryloyloxy)ethyl]trimethyl ammonium chloride) [QDMA]. DMF GPC analysis indicated an M_n of 17,700 and an M_w/M_n of 1.46 for the PPO-PGMA-PDMA triblock copolymer. The DMA residues of the PPO-PGMA-PDMA triblock copolymer were reacted with methyl iodide to prepare copolymers with differing degrees of quaternisation. Each triblock copolymer dissolved molecularly in aqueous solution at 5 °C and formed micelles with amine-functional coronas above a critical micelle temperature (CMT) of around 12 °C, which corresponded closely to the cloud point of the PPO macro-initiator. Cross-linking of the GMA residues in the inner shell using divinyl sulfone produced SCL micelles that remained intact at 5 °C, i.e. below the cloud point of the core-forming PPO block. Aqueous electrophoresis studies confirmed that these SCL micelles had considerable cationic surface charge, as expected. The cationic SCL micelles were adsorbed onto a near-monodisperse anionic silica sol, which was used as a model colloidal substrate. Thermogravimetric analyses indicated SCL micelle mass loadings of 6.1-15.5 wt.%, depending on the initial micelle concentration. Aqueous electrophoresis studies confirmed that surface charge reversal occurred on adsorption of the SCL micelles and scanning electron microscopy studies revealed the presence of SCL micelles on the silica particles.     

Effect of hydrophobicity inside PEO-PPO-PEO block copolymer micelles on the stabilization of gold nanoparticles: experiments

In this paper we present the effect of poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) block copolymer micelles and their hydrophobicity on the stabilization of gold nanoparticles. Gold nanoparticles were prepared by a method developed by Sakai et al. (Sakai, T.; Alexandridis, P. Langmuir 2004, 20, 8426). An absorption centered at 300-400 nm in time-dependent UV spectra provided evidence that the very first step of the synthesis was to form primary gold clusters. Then the gold clusters grew in size and were stabilized by block copolymer micelles. The stabilization capacities of the micelles were modulated by tuning the block copolymer concentration and composition and by adding salts. With good stabilization, gold particles were spherical and uniform in size with a diameter of 5-10 nm. Otherwise they were aggregates with irregular shapes such as triangular, hexagonal, and rodlike. The presence of a small amount of NaF significantly increased the stabilization capacity of the micelles and consequently modified the quality of the gold particles. Using FTIR and 1H NMR spectroscopy, micellization of the block copolymers and hydrophobicity of the micelles were proven very important for the stabilization. A higher hydrophobicity of the micelle cores was expected to favor the entrapment of primary gold clusters and the stabilization of gold nanoparticles.     

Enhanced stability of ZnTPPS by polymeric gold nanoparticles in acidic aqueous solutions

Novel kind of core-shell corona complex micelles were prepared, which enhanced both the hydrolytic stability and the photostability of water-soluble zinc tetrakis(4-sulfonatophenyl) porphyrin (ZnTPPS) in acidic aqueous solutions. The core-shell gold nanoparticles (AuNPS) were synthesized by reducing HAuCl₄ and di-thioester terminated block copolymer, poly(Nisopropylacrylamide)-block-poly(4-vinylpyridine) (PNIPAM-b-P4VP). The complex micelles with gold core, P4VP/ZnTPPS shell and PNIPAM corona were formed by simple mixing of gold nanoparticles and ZnTPPS. The photochemical properties of the complex micelles were studied by UV–Visiblespectroscopy and fluorescence spectroscopy. The results showed trapping of ZnTPPS in the positively charged micellar shell that effectively prevented demetallation of the ZnTPPS that would occur in acidic aqueous solutions. Furthermore, with appropriate concentration of gold nanoparticles, ZnTPPS in the complex micelle had excellent photostability by suppression of generation of reactive oxygen species (ROS). The enhanced stability of ZnTPPS in acidic aqueous media could be extensively used for photocatalysis and in solar cells.