Electrochemical Sensor Based on a Novel Pt−Au Bimetallic Nanoclusters Decorated on Reduced Graphene Oxide for Sensitive Detection of Ofloxacin

Pt−Au nanoclusters decorated on the surface of reduced graphene oxide (rGO/Pt−Au) was facilely prepared by one‐pot electrochemical reduction. The morphology and composition of rGO/Pt−Au composites had been characterized by scanning electron microscopy (SEM) coupled with energy‐dispersive X‐ray spectrometry (EDX), fourier transform‐infrared spectroscopy (FT‐IR) and electrochemical methods. Ofloxacin is a member of synthetic quinolones which has been widely used for the treatment of common diseases in humans and animals. The performance of the rGO/Pt−Au nanocomposite toward the oxidation of ofloxacin was compared with the other similar nanostructures like rGO/Pt and rGO/Au. In the optimized conditions, two linear calibration curves were obtained, from 0.08 to 10 μM and 10 to 100 μM ofloxacin. A detection limit of 0.05 μM ofloxacin was observed at pH 5.7 for the GCE/rGO/Pt−Au. The proposed sensor was successfully applied to determine ofloxacin in tablets and human urine samples and the results were satisfactory.     

质子惰性介质中硝基苯在铂微盘电极上的电化学行为

采用循环伏安法, 以铂微盘电极为工作电极, 铂片为辅助电极, 饱和甘汞电极为参比电极, 研究了硝基苯在含有四丁基高氯酸铵(TBAP)电解质的N,N-二甲基甲酰胺(DMF)有机溶液中的电化学行为, 并探讨了扫描速度和底物浓度等因素对硝基苯电化学特性的影响. 结果表明,该反应属扩散控制的准可逆反应.     

Fabrication of Trimetallic Pt−Pd−Co Porous Nanostructures on Reduced Graphene Oxide by Galvanic Replacement: Application to Electrocatalytic Oxidation of Ethylene Glycol

In present work, reduced graphene oxide nanosheets (rGO) decorated with trimetallic three‐dimensional (3D) Pt−Pd−Co porous nanostructures was fabricated on glassy carbon electrode (Pt−Pd−Co/rGO/GCE). First, GO suspension was drop‐casted on the electrode surface, then GO film reduction was carried out by cycling the potential in negative direction to form the rGO film modified GCE (rGO/GCE). Then, electrodeposition of the cobalt nanoparticles (CoNPs) as sacrificial seeds was performed onto the rGO/GCE by using cyclic voltammetry. Afterward, Pt−Pd−Co 3D porous nanostructures fabrication occurs through galvanic replacement (GR) method based on a spontaneous redox process between PtCl₂, PdCl_2, and CoNPs. The morphology and structure of the Pt−Pd−Co/rGO porous nanostructure film was characterized by scanning electron microscopy, energy dispersive spectroscopy and X‐ray diffraction method. The performance of the prepared electrode was investigated by various electrochemical methods including, cyclic voltammetry and electrochemical impedance spectroscopy. The electrocatalytic activity of the as‐prepared modified electrode with high surface areas was evaluated in anodic oxidation of ethylene glycol. The study on electrocatalytic performances revealed that, in comparison to various metal combinations in modified electrodes, trimetallic Pt−Pd−Co/rGO/GCE exhibit a lower onset potential, significantly higher peak current density, high durability and stability for the anodic oxidation of ethylene glycol. The excellent performances are attributed to the rGO as catalysts support and resulting synergistic effects of the trimetallic and appropriate characteristics of the resulted 3D porous nanostructures. Moreover, the influence of various concentrations of ethylene glycol, the potential scan rate and switching potential on the electrode reaction, in addition, long‐term stability have been studied by chronoamperometric and cyclic voltammetric methods.     

Reduced Graphene Oxide/Pt Nanoparticles/Zn‐MOF‐74 Nanomaterial for a Glucose Biosensor Construction

In this study, a new glucose biosensor was fabricated by immobilizing glucose oxidase (GOx) on platinum nanoparticles (Pt NPs) decorated reduced graphene oxide (rGO)/Zn‐MOF‐74 hybrid nanomaterial. Herein, the biosensor fused the advantages of rGO with those of porous Zn‐MOF and conductive Pt NPs. This has not only enlarged the surface area and porosity for the efficient GOx immobilization and faster mass transport, but also provided favorable electrochemical features such as high current density, remarkable electron mobility through metal nanoparticles, and improved electron transfer between the components. The GOx‐rGO/Pt NPs@Zn‐MOF‐74 coated electrode displayed a linear measurement range for glucose from 0.006 to 6 mM, with a detection limit of 1.8 μM (S/N: 3) and sensitivity of 64.51 μA mM^?1 cm^?2. The amperometric response of the enzyme biosensor demonstrated the typical behavior of Michaelis‐Menten kinetics. The obtained satisfying sensitivity and measurement range enabled fast and accurate glucose measurement in cherry juice using the fabricated biosensor. The water‐stable Zn‐MOF‐74 demonstrated higher enzyme loading capacity and can be potent supporting material for biosensor construction.     

铂/{还原氧化石墨烯/硅钨酸盐}_n复合物的制备及其电催化性能

利用层层自组装(LBL)结合原位光照还原法,制备了一系列{还原氧化石墨烯/多金属氧酸盐}n多层复合膜({rGO/POMs}_n),并以此作为载体,再通过恒电势法将Pt纳米粒子电沉积到复合膜载体上,得到一种P t/{rGO/SiW_(12)}_n燃料电池阳极纳米复合膜催化剂。用紫外可见分光光度计(UV-Vis)、原子力显微镜(AFM)以及扫描电子显微镜(SEM)等技术手段对载体复合多层膜的生长情况以及负载Pt纳米簇的表面形貌进行表征。结果表明,载体多层膜{rGO/SiW_(12)}_6被连续均匀地组装到了不同基底(氧化铟锡,ITO或玻碳,GC)表面且多层膜表面平整,在选定恒电势下,沉积于其表面的Pt纳米粒子具有花簇状形貌且分布均匀。比较研究了分别引入3种不同的多金属氧酸盐(硅钨酸盐SiW_(12),磷钼酸盐PMo_(12),磷钨酸盐PW_(12))制得的多层复合膜催化剂,即Pt/{rGO/SiW_(12)}_6、Pt/{rGO/PMo_(12)}_6和Pt/{rGO/PW_(12)}_6。电化学实验研究表明,在甲醇酸性溶液中,Pt/{rGO/SiW_(12)}_6复合膜相较于Pt/{rGO/PMo_(12)}_6、Pt/{rGO/PW_(12)}_6和Pt作为催化剂对甲醇氧化具有更好的电催化活性、电化学稳定性以及更优异的抗CO毒化性能,是一种颇有应用前景的燃料电池阳极催化剂。     

A Novel Biomimetic Hydrogen Peroxide Biosensor Based on Pt Flowers‐decorated Fe3O4/Graphene Nanocomposite

A sensitive and selective amperometric H₂O₂ biosensor was obtained by utilizing the electrodeposition of Pt flowers on iron oxide‐reduced graphene oxide (Fe₃O₄/rGO) nanocomposite modified glassy carbon electrode (GCE). The morphology of Fe₃O₄/rGO and Pt/Fe₃O₄/rGO was characterized by transmission electron microscopy (TEM) and scanning electron microscopy (SEM), respectively. The step‐wise modification and the electrochemical characteristics of the resulting biosensor were characterized by cyclic voltammetry (CV) and chronoamperometry methods. Thanks to the fast electron transfer at the Pt/Fe₃O₄/rGO electrode interface, the developed biosensor exhibits a fast and linear amperometric response upon H₂O₂. The linear range of Pt/Fe₃O₄/rGO is 0.1∼2.4 mM (R²=0.998), with a sensitivity of 6.875 μA/mM and a detection limit of 1.58 μM (S/N=3). In addition, the prepared biosensor also provides good anti‐interferent ability and long‐term stability due to the favorable biocompatibility of the electrode interface. The proposed sensor will become a reliable and effective tool for monitoring and sensing the H₂O₂ in complicate environment.     

Facile Synthesis of Pd‐Ni Nanoparticles on Reduced Graphene Oxide under Microwave Irradiation for Formic Acid Oxidation

Pd and Pd_x Ni nanoparticles have been supported on reduced graphene oxide (Pd/rGO and Pd_x Ni/rGO ) by using the microwave‐assisted heating method in glycol. The morphology, composition and electrochemical performance have been characterized by TEM , XRD , XPS and electrochemical methods. The XRD and XPS results show that there are no PdNi alloy particles formed in Pd_x Ni/rGO and the composites exist mostly in the form of Pd⁰ and NiOOH species. The electrochemical results reveal that Pd_x Ni/rGO synthesized from the feeding source of Pd and Ni with an atomic ratio of 4∶1 exhibits higher activity, better stability and smaller electron transfer resistance toward formic acid electro‐oxidation compared with commercial Pd/C, Pd/rGO and other Pd_x Ni/rGO samples. The excellent electrocatalytic performance indicates that the addition of appropriate amount of Ni can greatly enhance the activity and stability of Pd catalysts for formic acid oxidation.     

A Vanadium(V) Oxide Nanorod Promoted Platinum/Reduced Graphene Oxide Electrocatalyst for Alcohol Oxidation under Acidic Conditions

A Pt‐V₂O₅/rGO ternary hybrid electrocatalyst was designed by using active vanadium(V) oxide (V₂O₅) nanorods and reduced graphene oxide (rGO) components. The V₂O₅ nanorods were synthesized by a simple polyol‐assisted solvothermal method and were incorporated uniformly onto rGO sheets by intermittent microwave heating. Subsequently, Pt nanoparticles (2–3 nm in size) were deposited over the V₂O₅/rGO composite by the conventional polyol reflux method. The electrocatalytic performance of the Pt‐V₂O₅/rGO ternary hybrid and bare Pt/rGO catalysts towards the oxidation of simple alcohols was evaluated in acidic media. The ternary hybrid catalyst exhibited higher electrocatalytic activity than bare Pt/rGO and also showed good stability. The higher electrocatalytic activity of the Pt‐V₂O₅/rGO ternary hybrid was attributed to a synergistic effect among the Pt, V₂O₅, and rGO components. In addition, oxygen‐containing species, such as OH groups, were generated on V₂O₅ at lower potentials. These groups were able to scavenge intermediate species such as CO_ads on the Pt surfaces and helped to regenerate the active sites on the Pt surface more effectively for the routine alcohol oxidation reaction.     

不同结构及氮掺杂NiO/rGO氧还原催化剂的制备与性能研究

本文以还原氧化石墨烯（rGO）为载体制备了片状NiO/rGO和球形NiO/N-rGO结构的氧还原催化剂. 通过X-射线衍射（XRD）、Raman（拉曼）测试、X-射线光电子能谱（XPS）、扫描电子显微镜（SEM）和透射电子显微镜（TEM）等方法表征了两种催化剂的结构和形貌. 采用循环伏安法（CV）、Tafel曲线、线性扫描伏安法（LSV）、旋转圆盘电极（RDE）和旋转环盘电极（RRDE）等技术测试研究了两种催化剂的电化学催化氧还原性能. 研究结果表明,球形NiO/N-rGO催化剂催化氧还原的峰电流密度和起始电位（0.89 V vs. RHE）与商业化的Pt/C（20%）催化剂相近. 旋转圆盘电极（RDE）和旋转环盘电极（RRDE）测试证明,在碱性电解液中NiO/rGO和NiO/N-rGO催化的氧还原反应均主要通过4?鄄电子途径反应途径发生,球形NiO/N-rGO催化剂展现出替代Pt/C基催化剂的潜力.     

Facile Synthesis of Platinum–Cerium(IV) Oxide Hybrids Arched on Reduced Graphene Oxide Catalyst in Reverse Micelles with High Activity and Durability for Hydrolysis of Ammonia Borane

Highly dispersed Pt‐CeO₂ hybrids arched on reduced graphene oxide (Pt‐CeO₂/rGO) were facilely synthesized by a combination of the reverse micelle technique and a redox reaction without any additional reductant or surfactant. Under a N₂ atmosphere, the redox reaction between Ce³⁺ and Pt²⁺ occurs automatically in alkaline solution, which results in the formation of Pt‐CeO₂/rGO nanocomposites (NCs). The as‐synthesized Pt‐CeO₂/rGO NCs exhibit superior catalytic performance relative to that shown by the free Pt nanoparticles, Pt/rGO, Pt‐CeO₂ hybrid, and the physical mixture of Pt‐CeO₂ and rGO; furthermore, the nanocomposites show significantly better activity than the commercial Pt/C catalyst toward the hydrolysis of ammonia borane (NH₃BH₃) at room temperature. Moreover, the Pt‐CeO₂/rGO NCs have remarkable stability, and 92 % of their initial catalytic activity is preserved even after 10 runs. The excellent activity of the Pt‐CeO₂/rGO NCs can be attributed not only to the synergistic structure but also to the electronic effects of the Pt‐CeO₂/rGO NCs among Pt, CeO₂, and rGO.     

Electrochemical sensor for ultrasensitive determination of ceftazidime using hollow platinum nanoparticles/reduced graphene oxide/pencil graphite electrode

In this paper, an electrochemical sensor was prepared based on the modification of pencil graphite electrode (PGE) by hollow platinum nanoparticles/reduced graphene oxide (HPtNPs/rGO/PGE) for determination of ceftazidime (CFZ). Initially, rGO was electrodeposited on the electrode surface, and then, hollow platinum nanoparticles were placed on the electrode surface via galvanic displacement reaction of Pt(IV) ions with cobalt nanoparticles (CoNPs) that had electrodeposited on the electrode surface. Several significant parameters controlling the performance of the HPtNPs/rGO/PGE were examined and optimized using central composite design as one optimization methodology. The surface morphology and elemental characterization of the bare PGE, rGO/PGE, CoNPs/rGO/PGE, and HPtNPs/rGO/PGE-modified electrodes was analyzed by field-emission scanning electron microscopy, transmission electron microscopy, energy-dispersive X-ray spectroscopy, and electrochemical impedance spectroscopy. The electrochemical activity of CFZ on resulting modified electrode was investigated by cyclic voltammetry (CV) and adsorptive differential pulse voltammetry (AdDPV). Adsorptive differential pulse voltammetry indicates that peak current increases linearly with respect to increment in CFZ concentration. CFZ was determined in the linear dynamic range of 5.0 × 10^?13 to 1.0 × 10^?9 M, and the detection limit was determined as 2.2 × 10^?13 M using AdDPV under optimized conditions. The results showed that modified electrode has high selectivity and very high sensitivity. The method was used to determine of CFZ in drug injection and plasma samples.     

In-Situ Electrodeposition of Rhodium nanoparticles Anchored on Reduced Graphene Oxide nanosheets as an Efficient Oxygen Reduction Electrocatalyst

A simple, versatile, and cost-effective one-pot electrochemical deposition is used to fabricate rhodium (Rh) nanoparticles decorated surface of reduced graphene oxide (rGO) functionalized glassy carbon electrode (GCE) for oxygen reduction reaction (ORR) in alkaline media. The chemical and physical structure of the sample is probed via transmission electron microscopy, rotating disk electrode (RDE), X-ray photoelectron spectroscopy, linear sweep voltammetry, and Raman spectroscopy. The synergistic effects between the unique properties of Rh nanoparticles and rGO creates such innovative hybrid that exhibits a catalytic activity comparable to that of the commercial platinum electrocatalyst (Pt/C). As a result, the as-electrodeposited Rh@rGO hybrid exhibits outstanding ORR activity in alkaline media, as evidenced by a larger diffusion-limited current, greater positive onset potential, much better stability and methanol tolerance than Pt/C under the same conditions.     

The influence of disproportionation of the anion radical on the electrochemical reduction of 1,9-dimethyldibenzo[b,f]pentalene

The electrochemical reduction of 1,9-dimethyldibenzo[b,f]pentalene has been investigated in DMF by both cyclic voltammetry (CV) and dc polarography. The influence of the depolarizer concentration and electrode material (Pt and Hg) was studied. It was found that the first electron transfer is a reversible one under most conditions studied, whereas the second electron transfer was irreversible on Pt and quasi-reversible on the HMD. An overall EDISP.EC mechanism was suggested and discussed. It turned out that the first reduction process was accompanied by a disproportionation of the anion-radical to its parent hydrocarbon and dianion. The experimental waves were analysed on the basis of various theoretical procedures.     

负载硫化钴纳米颗粒的N、S共掺杂石墨烯氧还原电催化剂的制备及性能

采用D-氨基葡萄糖作为Co分散剂和碳源,硫脲作为氮源和硫源,以NaCl为模板制备负载硫化钴纳米颗粒的N、S共掺杂三维石墨烯氧还原电催化剂(CoS/N/S/rGO)。CoS/N/S/rGO具有良好的氧还原反应(ORR)活性,起始电位和半波电位分别为960和815 mV,性能与商业Pt/C相当。此外,CoS/N/S/rGO表现出明显的4电子转移特性和超低的过氧化氢产率。与基于Pt/C的锌-空气电池相比,基于CoS/N/S/rGO的锌-空气电池在6 mol·L~(-1) KOH和0.2 mol~(-1) Zn(CH_3COO)_2碱性电解质中显示出更高的恒电流放电性能以及更好的稳定性。     

Hydrothermal Synthesis of a rGO Nanosheet Enwrapped NiFe Nanoalloy for Superior Electrocatalytic Oxygen Evolution Reactions

Graphene‐based hybrid nanostructures possess many advantages in the field of electrochemical energy applications. In this work, a facile and efficient hydrothermal approach has been developed for the preparation of NiFe alloy nanoparticles/rGO hybrid nanostructures, in which the nanoparticles are well combined with rGO nanosheets and the size of the nanoparticles is about 100 nm. Moreover, the electrochemical oxygen evolution reaction (OER) tests confirmed that the obtained NiFe/rGO hybrid nanostructures possess notably higher activity than both the rGO‐free NiFe nanoparticles and pure Ni/rGO hybrids, and the optimal NiFe ratio is 2:1. The OER overpotential at 20 mA cm^?1?2 with Ni₂Fe/rGO is as low as 0.285 V, which is 96 mV lower than that of pure Ni/rGO hybrids. Meanwhile, the Ni₂Fe/rGO catalyst has excellent stability. Therefore, this work contributes a facile and efficient method to prepare a NiFe alloy nanoparticles/rGO hybrid structure for potential applications in the field of electrochemical energy devices, such as electrochemical water splitting cells, rechargeable metal/air batteries, etc.     

One-step synthesis of Pt nanoparticles/reduced graphene oxide composite with enhanced electrochemical catalytic activity

A one-step electrochemical approach for synthesis of Pt nanoparticles/reduced graphene oxide(Pt/RGO) was demonstrated.Graphene oxide(GO) and chloroplatinic acid were reduced to RGO and Pt nanoparticles(Pt NPs) simultaneously,and Pt/RGO composite was deposited on the fluorine doped SnO 2 glass during the electrochemical reduction.The Pt/RGO composite was characterized by field emission-scanning electron microscopy,Raman spectroscopy and X-ray photoelectron spectroscopy,which confirmed the reduction of GO and chloroplatinic acid and the formation of Pt/RGO composite.In comparison with Pt NPs and RGO electrodes obtained by the same method,results of cyclic voltammetry and electrochemical impedance spectroscopy measurements showed that the composite electrode had higher catalytic activity and charge transfer rate.In addition,the composite electrode had proved to have better performance in DSSCs than the Pt NPs electrode,which showed the potential application in energy conversion.     

阴极催化剂对微生物燃料电池性能的影响

以不同载量的MnO_2/rGO和Pt/C修饰阴极电极构建了生物阴极型双室微生物燃料电池(MFC),考察了不同阴极催化剂修饰MFC对其产电性能以及老龄垃圾渗滤液主要污染物去除效果的影响。结果表明,以MnO_2/rGO修饰MFC阴极电极材料,能显著提高MFC产电性能及对老龄垃圾渗滤液中污染物去除效果;输出电压为372 mV,功率密度为194 mW/m~3(是未经催化剂修饰MFC的两倍),内阻为264Ω,化学需氧量(COD)和氨氮(NH_3-N)去除率分别为58.68%和76.64%。当MnO_2/rGO载量为.0 mg/cm~2时,MFC性能与负载Pt/C的MFC性能接近,但构建成本却明显降低。     

高分散的介孔碳载Pt纳米粒子的制备及其对乙二醇的电催化氧化性能

以二氧化硅溶胶为硬模板,嵌段聚合物F127为软模板,通过双模板法合成了高介孔比例、窄孔径分布的介孔碳(MC).进而经乙二醇还原法制备了高分散的MC载铂催化剂(Pt/MC).采用循环伏安、计时电流、线性扫描伏安和电化学阻抗谱法研究了硫酸溶液中乙二醇在Pt/MC催化剂电极上的电化学氧化行为.实验结果表明,Pt/MC催化剂对乙二醇的电催化氧化性能显著高于商业化炭黑XC72R载Pt(Pt/XC72R)催化剂.电化学阻抗谱分析进一步揭示,乙二醇在Pt/MC催化剂电极上的电氧化反应具有较低的电荷传递电阻.Pt/MC催化剂高的电催化活性可以归结于MC大的孔径和均一的介孔结构对电子传输和传质的促进作用.     

Electrochemical-reduction-assisted Assembly of Pd NPs/Polyoxometalates/Graphene Ternary Nanocomposite and Its Electrocatalytic Performance toward Formic Acid Oxidation

A novel ternary nanocomposite, Pd nanoparticles(NPs)/polyoxometalates(POMs)/reduced graphene oxide(rGO), was prepared by a green, mild, electrochemical-reductionassisted assembly. It is worth noting that the Keggin-type POM acts as an electrocatalyst as well as a bridging molecule. During the reduction process, POMs transfer the electrons from the electrode to GO, leading to a deep reduction of GO and the content of oxygen-containing groups is decreased to around 6.1%. Meanwhile, the strong adsorption effect between the POM clusters and rGO nanosheets induces the spontaneous assembly of POM on r GO in a uniformly dispersed state, forming a nanocomposite. The ternary Pd NPs/POMs/rGO nanocomposite exhibits higher electrocatalytic activities, better electrochemical stability, and higher resistance to CO poisoning than the Pd/C catalyst towards the formic acid oxidation(FAOR). Especially, the Pd/PW_(12)/rGO exhibits the best electrocatalytic performance among three Pd/POMs/rGO composites(POMs = PW_(12), SiW_(12), PMo_(12)).     

Synthesis of Silver Nanoparticle‐Graphene Composites for Electroanalysis Applications using Chemical and Electrochemical Methods

An electrochemical device was developed for the simultaneous determination of sulfamethoxazole (SMX) and trimethoprim (TMP) using differential pulse voltammetry and glassy carbon (GC) electrodes modified with reduced graphene oxide (rGO) and silver nanoparticle (AgNP) composites, synthesised using both chemical and electrochemical methods. The morphology and electrochemical behaviour of the GC electrodes modified with the rGO/AgNP (chemical method) and rGO‐AgNP (electrochemical method) composites were characterised by scanning electron microscopy and cyclic voltammetry. These techniques demonstrated that, in both methods, the graphene oxide was modified by the AgNPs, and the composite synthesised by the electrochemical method showed a better dispersion of the nanoparticles, resulting in an increase in the surface area compared to the rGO/AgNP composite. The GC/rGO‐AgNP electrode was evaluated and optimised for the simultaneous determination of SMX and TMP, achieving detection limits of 0.6 μmol L⁻¹ for the SMX and 0.4 μmol L⁻¹ for the TMP. The proposed GC/rGO‐AgNP electrochemical device was successfully applied to the simultaneous determination of SMX and TMP in wastewaters samples.