载体对担载Ni催化剂甲烷与二氧化碳重整反应活性的影响

制备了 Zr O2 、Mg O改性的 Al2 O3、Ti O2 复合载体 ,并应用 X-射线粉末衍射 (XRD)、比表面积测定、扫描电镜 (SEM)等手段进行了表征 .结果表明 ,这些氧化物在 Al2 O3上的晶粒尺寸小、比表面积大 ,分散较好 ,而在Ti O2 上的分散性较差 .对经 10 73K焙烧的 Mg O/ Ti O2 ,还发现部分 Ti O2 载体由锐钛矿变为金红石 ,同时生成Mg Ti O3 新相 .考察了载体对 Ni催化剂的 CH4与 CO2 重整反应活性的影响 ,其次序为 :Mg O/ Al2 O3>Zr O2 /Al2 O3>Al2 O3>Mg O >Zr O2 >Ti O2 >Mg O/ Ti O2 . Ti O2 及 Mg O/ Ti O2 担载 Ni催化剂的低活性可能与 Ti O2 本身的还原性有关     

NiO-MgO固溶体的形成对Ni/MgO-AN催化CO2重整CH4反应活性和稳定性的影响

 以在流动N2中热处理的Mg(OH)2醇凝胶制得的纳米氧化镁(MgO-AN)为载体,浸渍Ni(NO3)2后经不同温度焙烧得到Ni含量为8.8%的NiO/MgO样品,还原后制得Ni/MgO-AN催化剂. 采用XRD和TPR技术对NiO和MgO之间形成的NiO-MgO固溶体进行了表征,并将Ni/MgO-AN催化剂用于催化CO2重整CH4反应. 结果表明,在低于650 ℃焙烧时, NiO不能完全溶入MgO中,NiO/MgO样品中存在自由的NiO粒子,还原态Ni/MgO-AN催化剂在CO2重整CH4反应中的稳定性低; 当样品焙烧温度等于或高于650 ℃时,NiO可以完全溶入MgO中形成NiO-MgO固溶体,还原态Ni/MgO-AN催化剂具有高稳定性.     

Ni/MgO-CeO2催化低温乙醇水蒸气重整制氢

采用固相燃烧法制备了MgO,CeO2载体和不同摩尔比的Mgo-CeO2复合载体,采用浸渍法制备了Ni/MgO,Ni/CeO2,Ni/Mgo-CeO2系列催化剂,考察了各催化剂催化乙醇水蒸气重整反应的性能.用BET技术测定了载体的比表面,并用X射线衍射(XRD)、程序升温还原(TPR)和热重(TG)技术对催化剂进行表征.结果表明,在Ni/CeO2和Ni/Mgo-CeO2上,Ni以高分散的NiO、体相NiO和与载体发生相互作用的NiO的形式存在,显示了良好的低温乙醇水蒸气重整性能;其中Mg,Ce摩尔比为1:1时,Ni/MgO-CeO2催化剂显示了良好的活性和选择性,并且具有很好的稳定性和抗积炭能力.     

正丁烷在VMgO和Ni-VMgO催化剂上氧化脱氢

 采用4种方法制备了VMgO催化剂样品(w(V2O5)=30%,w(MgO)=70%),并将其用于正丁烷氧化脱氢气固相反应. 结果表明,MgO经蒸馏水回流和焙烧处理后再用NH4VO3溶液浸渍所制得的VMgO,对正丁烷氧化脱氢生成丁烯和丁二烯反应具有更好的催化性能. 这是由于用该法制备的VMgO催化剂中存在较多的Mg3V2O8物种. 通过添加Ni对VMgO催化剂进行了改性. 结果表明,适量添加Ni(n(Ni)/n(V)=0.3)有利于催化剂中Mg3V2O8的生成,而Ni以Ni3V2O8的形态存在. 由此明显改善了VMgO催化剂对正丁烷氧化脱氢生成丁烯和丁二烯反应的催化性能.     

镁铝混合氧化物负载镍催化剂的制备及在液化石油气低温重整反应中的催化性能

采用共沉淀-浸渍法制备了不同Ni含量的Ni/Mg(Al)O催化剂并用于液化石油气(LPG)的低温水蒸气重整反应.X射线衍射和程序升温还原结果表明,在800℃焙烧的Ni/Mg(Al)O催化剂中,NiO与MgO反应生成Mg-Ni-O固溶体,还原后形成金属Ni纳米颗粒.详细研究了Ni含量(质量分数)、反应温度和水/碳摩尔比(nH2O/nC)等对催化剂性能的影响.实验结果表明,15%Ni/Mg(Al)O催化剂对LPG低温重整反应具有最佳的催化性能.提高反应温度能显著提高Ni/Mg(Al)O催化剂的催化性能.当nH2O/nC=2时,在400～500℃的温度范围使LPG完全转化的最大反应空速从28900 mL.h-1.g-1 Cat提高到86800 mL.h-1.g-1Cat.适当增大水/碳摩尔比有利于LPG转化为小分子气体,但在LPG摩尔流量不变的情况下,反应气中水含量过高会导致LPG转化率降低.反应后催化剂的X射线衍射谱(XRD)和热重分析(TG)结果表明,Ni/Mg(Al)O催化剂优良的催化活性和反应稳定性可归因于催化剂表面Ni晶粒较高的稳定性和抗积炭性能.     

Preparation and Characterization of High Purity Al（2-x）Mg（x＋y）Ti（1-y）O（5-0.5x-y） Solid Solution

A small amount of mineralizer MgO was added into Al2TiO5 synthesized from the sludge of aluminum factory to form Al（2-x）Mg（x＋y）Ti（1-y）O（5-0.5x-y） solid solution and inhibit the decomposition of Al2TiO5 solid solution. It increased the content of Al2TiO5 solid solution and improved the thermal stability of materials. In this work,XRD and SEM methods were adopted to characterize the crystalline structure and microstructure of each kind of sample. Rietveld Quantification method was used to determine the content of crystalline phases in each sample. Results show as follows： the optimal addition concentration of MgO was 2.0%,and the corresponding content of Al2TiO5 solid solution which displayed irregular bulk shape was 100%; the addition of mineralizer MgO could enhance the flexural strength and thermal stability of Al2TiO5 solid solution materials. The optimal addition concentration of MgO determined by performance analysis was 2.0%,and its corresponding retention rate of thermal-shock flexural strength was 86.4%. Structure analysis and performance analysis resulted in good accordance.     

Ce0.5-xZr0.5-xBa2xO2负载TiO2光催化降解气相苯

在密闭不锈钢反应器内研究了Ce0.5-xZr0.5-xBa2xO2负载锐钛型TiO2光催化降解气相苯的性能.确定了该系列光催化剂的最佳Ba含量,并应用X射线衍射、紫外-可见漫反射光谱以及X射线光电子能谱对催化剂进行了表征.结果表明,TiO2在载体表面均匀分散.在210~400 nm范围内,TiO2/Ce0.5-xZr0.5-xBa2xO2比TiO2吸收更多的紫外光.TiO2/Ce0.5-xZr0.5-x-Ba2xO2包含Ti和O两种元素,TiO2/Ce0.5-xZr0.5-xBa2xO2的Ti 2p结合能向低能端偏移.Ce0.5-xZr0.5-xBa2xO2表面负载TiO2能有效提高催化剂的光催化活性.Ce0.5-xZr0.5-xBa2xO2的作用是转移电子和使催化剂在紫外区的吸收增强.     

Mg1-xTixNi(0≤x≤0.4)系列合金的合成及性能研究

采用机械合金化法成功制备了Mg1-xTixNi(0≤x≤0.4)系列三元合金.XRD结构分析表明,不同成分的合金在相同的球磨时间下非晶化程度有所区别,并且合金的非晶化程度随着球磨时间的增加而趋于完全.少量Ti的加入使得该系列合金的电化学性能及循环稳定性都有所提高.在球磨120h的该系列合金中,Mg0.9Ti0.1Ni合金的最大初始放电容量达到356.85mA·h·g-1(100mA·g-1,-0.5Vvs.Hg/HgO),而Mg0.7Ti0.3Ni合金的循环稳定性最好.Ti的加入亦提高了合金的抗腐蚀性能,使其腐蚀电位正移.     

CH4,CO2和O2制合成气反应中载体对催化剂抗积炭性能的影响

在CH4,CO2 和O2 催化氧化制合成气反应中 ,积炭是催化剂活性减弱的一个重要因素 .通过向Ni/Al2 O3 添加各种氧化物后 ,催化剂的抗积炭性能得到了提高 .实验结果表明 ,催化剂的抗积炭顺序为 :Ni/CaO Al2 O3 >Ni/MgO Al2 O3 >Ni/TiO2 Al2 O3>Ni/CeO2 Al2 O3 >Ni/La2 O3 Al2 O3 >Ni/Y2 O3 Al2 O3 >Ni/Fe2 O3 Al2 O3 >Ni/Al2 O3 ,并通过CO2 TPD ,O2 TPD ,XPS等方法对催化剂进行表征 ,讨论了抗积炭顺序与催化剂性能的关系 .     

Effects of Carrier on CuO／TiO2 and CuO／Ti0.5Zr0.5O2 Catalysts in the NO＋CO Reaction

Using TiO2 and Ti0.5Zr0.5O2 as carriers, the CuO/TiO2 and CuO/Ti0.5Zr0.5O2 catalysts were prepared by the impregnation method with Cu(NO3)2 as active component. The catalytic activities in NO CO reaction were investigated using a microreactor-GC system, and structure and reducibility of catalysts were characterized by means of physical adsorption, TPR, XRD, NO-TPD technologies. It was found that the activity of CuO/Ti0.5Zr0.5O2 catalyst was higher than that of CuO/TiO2, probably due to the large specific surface area of Ti0.5Zr0.5O2 that played an important role in NO CO reaction.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

化学计量中不确定度评定研究进展

测量不确定度是表征合理地赋予被测量之值的分散性的参数。本文针对化学计量不确定度评定基础模型仅适用于线性模型、概率分布为正态分布或缩放位移t分布等局限,介绍了近年来不确定度评定的研究热点:蒙特卡罗方法(Monte Carlo Method,MCM),不确定度评定的来源、评定概念、评估方法及其发展过程,扩大了测量不确定度评定与表示的适用范围。     

微量钙的测定方法研究进展

介绍了1995-2006年期间测定微量和痕量钙的方法,如电感耦合等离子体-原子发射光谱法、原子吸收光谱法以及离子色谱法等的工作原理和特点,并说明了其测定微量钙的应用领域。并对微量钙的测定技术进行了展望(引用文献55篇)。     

Stages of thermal decomposition of sodium oxo-salts of sulphur

Thermal behaviour of sodium oxo-salts of sulphur: Na₂SO₄, Na₂S₂O₇, Na₂S₂O₆, Na₂SO₃, Na₂S₂O₅, Na₂S₂O₄, Na₂S₂O₃, Na₂S₃O₆ and of sulphides Na₂S and Na₂S₂ was studied on heating up to 1000°C. The experiments were performed with anhydrous compounds obtained from commercial products by recrystallisation and dehydration. The stage mechanisms of decomposition of anionic sub-lattices of the salts have been proposed basing on the Górski’s morphological classification of simple species. The thermal stability and the stage decomposition mechanisms were correlated with the structure and the potential chemical properties of the salt anions. The thermal decomposition processes were studied by means of thermal analysis, and the decomposition products were identified by means of X-ray phase analysis.