从SiCl4合成多孔硅/碳复合材料及储锂性能研究

以Li₁₃Si₄和SiCl₄为原料,通过简单的机械球磨法合成多孔硅/碳复合材料,通过控制Li₁₃Si₄颗粒的尺寸可以有效调节产物的比表面积。分别研究了包覆碳含量、多孔硅/SuperP(导电碳)比表面积以及极片活性物质负载量对多孔硅/碳复合材料电化学性能的影响。结果表明:多孔硅/SuperP比表面积为100.9m₂·g^-1,化学气相沉积(CVD)包覆碳含量为25.3wt%(约6nm厚)的复合材料具有最高的电化学活性,在300mA·g^-1的电流密度下,循环可逆比容量达到1900mAh·g^-1,50次循环后容量仅衰减7.6%。     

一种新碳源包覆的LiFePO4/C正极材料的合成及性能

以富含植物蛋白的豆浆作为碳源, 以FePO₄·4H₂O和LiOH·H₂O为原料, 采用流变相方法合成了锂离子电池正极材料LiFePO₄/C. X射线衍射(XRD)和扫描电子显微镜(SEM)的表征结果显示, 样品具有良好的结晶性能, 平均粒径约200 nm, 颗粒表面有均匀网络状的碳包覆. 充放电循环研究结果表明: LiFePO₄/C具有稳定的电化学循环性能, LiFePO₄/C正极材料在0.1C倍率下首次放电比容量达到156 mAh·g^-1, 首次充放电效率达到98.7%; 循环40次后, 放电比容量为149 mAh·g^-1, 电池容量保持率在95%以上, 1C倍率下首次放电比容量达到134.7 mAh·g^-1, 显示出较高的电化学容量和优良的循环稳定性.     

二维层状Ti3C2Tx-MXene@VS2用于高性能锂离子电池负极

为探索一种高性能的锂离子电池负极材料,采用酸刻蚀法制备了高导电性、高稳定性的二维层状Ti₃C₂T_x,通过溶剂热法制备了具有高理论比容量的花瓣状VS₂纳米片,再经过简单的液相混合得到了二维层状Ti₃C₂T_x-MXene@VS₂复合物。通过扫描电子显微镜、透射电子显微镜、X射线光电子能谱、X射线衍射和能谱分析对复合材料的形貌和结构进行了表征,采用循环伏安、恒流充放电、长循环和交流阻抗谱对复合材料的电化学性能进行了研究。结果表明：VS₂纳米片均匀地分布在Ti₃C₂T_x的层间及表面,该复合物具有高的可逆容量(电流密度为0.1A·g^-1时,比容量为610.5mAh·g^-1)、良好的倍率性能(电流密度为2A·g^-1时,比容量为197.1mAh·g^-1)和良好的循环稳定性(电流密度为0.2 A·g^-1时,循环600圈后比容量为874.9 mAh·g^-1;电流密度为2 A·g^-1时,循环1 500圈后比容量为115.9mAh·g^-1)。     

N掺杂MnO2/碳布复合材料的制备及储锂性能

采用碳布（CC）为柔性基底,通过水热法制备了MnO₂/CC及N掺杂MnO₂/CC无黏结剂负极材料,借助X射线衍射（XRD）、扫描电镜（SEM）、X射线光电子能谱（XPS）、比表面积测试和恒电流充放电对材料进行了结构表征及电化学性能测试。结果表明N掺杂MnO₂/CC具有良好的倍率性能和循环稳定性。在0.1 A·g^-1的电流密度下,其首次充电比容量为948.8 mAh·g^-1,经过不同倍率测试后电流密度恢复至0.1 A·g^-1时仍然保持有907.9 mAh·g^-1的可逆比容量,容量保持率为95.7%。在1 A·g^-1的大电流密度下,其首次充电比容量为640.3 mAh·g^-1,循环100次后仍然保持有529.9 mAh·g^-1的可逆比容量,容量保持率为82.8%,可逆比容量远高于商用MnO₂。     

异质双碳源对LiMn0.8Fe0.2PO4复合材料电化学性能的影响

采用水基流变相辅助的固相法,以异质碳蔗糖和石墨为碳源,合成了LiMn_0.8Fe_0.2PO₄/C复合材料,研究了不同石墨加入方式对所制复合材料电化学性能的影响,并对所制备的LiMn_0.8Fe_0.2PO₄/C复合材料进行了X射线衍射(XRD)、N₂吸附-脱附测试、扫描电子显微镜(SEM)、透射电子显微镜(TEM)等表征。结果表明,不同石墨包覆工艺对材料结构和电化学性能具有显著影响。前驱体煅烧后再加入石墨获得的样品纯度高,形貌呈均一的椭圆形,在0.1C下的放电比容量为149 mAh·g^-1,达到其理论比容量的87%;在5C下最大的放电比容量为133 mAh·g^-1;在2C倍率下经过300次循环后比容量维持在127 mAh·g^-1,衰减率仅为1.9%,表现出了优良的循环稳定性。     

以氨基化的聚苯乙烯微球为模板制备电致变色性能优良的单层有序多孔PBTB薄膜

以氯化钨和氧化石墨烯(GO)为原料,乙醇为溶剂,一步合成了WO₃纳米棒/石墨烯纳米复合材料(WO₃/RGO). 将WO₃/RGO纳米复合材料用于锂离子电池负极,并通过充放电测试、循环伏安(CV)和电化学阻抗谱(EIS)技术综合考察了该材料的储锂性能. 结果显示,在0.1C (1C=638 mA·g^-1)倍率下,复合物的首次放电比容量达到761.4 mAh·g^-1,100次循环后可逆容量仍保持在635 mAh·g^-1,保持率为83.4%. 即使在5C倍率下容量仍高达460 mAh·g^-1. 由此说明,WO₃/RGO纳米复合物具有优异的循环稳定性及倍率性能,可望用于高性能锂离子电池.     

表面活性剂碳化法合成Fe3O4/C复合物及其电化学性能

以水热法合成的包覆油酸的α-Fe₂O₃粒子为前驱体, 在氩气下500 °C煅烧1 h, 得到Fe₃O₄/C纳米复合物. 用傅里叶变换红外(FTIR)光谱, X射线衍射(XRD), 扫描电镜(SEM), X射线能量散射(EDX)谱, 高分辨透射电镜(HRTEM), 元素分析, 循环伏安(CV)和恒流充放电测试等方法对材料的结构、形貌、成分及电化学性能进行了表征. 结果表明: 所制备的Fe₃O₄/C复合物呈长约200 nm, 粗约100 nm的纺锤形, 表面碳层厚约1-2 nm, 碳含量为1.956%(质量分数); 这种复合物作为锂离子电池负极材料具有很好的循环稳定性(在0.2C (1C=928 mA·g^-1)循环80次后具有691.7 mAh·g^-1比容量)和倍率性能(在2C循环20次后依然有520 mAh·g^-1比容量). 相对于未包覆的商业Fe₃O₄粒子, 复合物显著提高的电化学性能是由于碳包覆能防止粒子聚集, 提高导电性以及稳定固体电解质界面(SEI)膜.     

异质双碳源对LiMn0.8Fe0.2PO4复合材料电化学性能的影响

采用水基流变相辅助的固相法,以异质碳蔗糖和石墨为碳源,合成了LiMn_0.8Fe_0.2PO₄/C复合材料,研究了不同石墨加入方式对所制复合材料电化学性能的影响,并对所制备的LiMn_0.8Fe_0.2PO₄/C复合材料进行了X射线衍射(XRD)、比表面积测试、扫描电子显微镜(SEM)、透射电子显微镜(TEM)等表征。结果表明,不同石墨包覆工艺对材料结构和电化学性能具有显著影响。前驱体煅烧后再加入石墨获得的样品纯度高,形貌呈均一的椭圆形,在0.1C下的放电比容量为149 mAh·g^-1,达到其理论比容量的 87%;在 5C 下最大的放电比容量为 133 mAh·g^-1;在 2C 倍率下经过 300 次循环后比容量维持在 127 mAh·g^-1,衰减率仅为1.9%,表现出了优良的循环稳定性。     

百香果皮基原位氮掺杂多孔碳/硫复合正极的制备及储锂性能

以生物质百香果皮为碳源,KHCO₃为活化剂,采用同步活化碳化方法制备原位氮掺杂的分级多孔碳材料,将其与单质硫复合制得多孔碳/硫正极材料。通过X射线衍射（XRD）、X射线光电子能谱（XPS）、扫描电子显微镜（SEM）、透射电子显微镜（TEM）等表征技术对制备材料的物相组成、微观形貌、比表面积及孔结构进行研究分析。同时,利用紫外可见吸收光谱研究了多孔碳对多硫化物的吸附作用,用恒电流充放电测试了不同硫含量（60%~80%）的多孔碳/硫复合正极材料的电化学性能。结果表明,制得的多孔碳材料为无定型,具有1 093 m²·g^-1的高比表面积和0.63 cm³·g^-1的孔容;丰富的多孔结构和原位氮掺杂对多硫化物的物理化学协同吸附作用,有效降低了锂硫电池的“穿梭效应”,提高了电池的放电比容量和循环性能。硫含量为60%的多孔碳/硫复合材料,在0.05C和0.2C倍率下可释放1 057.7和763.4 mAh·g^-1的高初始放电比容量,在1C的高倍率下循环300次后的保持率为75%。     

两步固相法合成LiFe1-xNbxPO4/C复合正极材料及其电化学性能

以LiH₂PO₄和FeC₂O₄·2H₂O为原料, 采用分步添加聚乙烯醇和葡萄糖两种碳源的方式, 通过两步固相法合成了碳包覆的LiFePO₄材料. 700℃下处理的产物结晶良好, 颗粒分布均匀, 具有良好的电化学性能, 0.1C和1C倍率下放电比容量分别为157.3 和138.3 mAh·g^-1. 在碳包覆的基础上, 选择高价Nb⁵⁺进行铁位取代获得了复合改性的LiFe_1-xNb_xPO₄/C (x=0.005, 0.01, 0.015, 0.02)材料. 优化的LiFe_0.99Nb_0.01PO₄/C 材料显示了良好的倍率充放电能力和循环稳定性, 0.1C和5C倍率下放电比容量分别为160.5 和136.0 mAh·g^-1, 5C倍率下循环50 次后比容量保持在134.8 mAh·g^-1, 容量保持率为99.1%. 循环伏安测试结果表明, Nb⁵⁺离子掺杂减少了锂离子扩散阻力, 降低了充放电过程中的动力学限制, 提高了电极的可逆性.     

有序介孔C/NiO复合材料的合成及其电化学性能

以嵌段共聚物F127(Mw=12600, PEO106PPO70PEO106)为模板剂, Ni(Ac)2·4H2O为Ni源, 低分子量的酚醛树酯为碳源, 通过溶胶-凝胶三元共组装方法合成高度有序介孔C/NiO复合材料. 对样品进行X射线衍射(XRD)、透射电子显微镜(TEM)、N2吸脱附等结构表征及循环伏安(CV)等电化学性能测试. 结果显示, NiO晶体和碳组成了C/NiO复合材料的基本骨架, 该复合材料具有高度有序的介孔结构. NiO晶体的存在极大地提高了复合材料的电化学性能, 当C/NiO达到4:1(苯酚与Ni(Ac)2·4H2O的摩尔比)时复合材料的比电容达到444.1 F·g-1, 而有序的介孔结构并没有被破坏, 使得该材料具有较好的应用前景.     

MOF-derived hollow NiO–ZnO composite micropolyhedra and their application in catalytic thermal decomposition of ammonium perchlorate

Ni(II)-doped Zn-based coordination polymer particles (Ni(II)-doped Zn-CPPs) with controllable shape and size were successfully synthesized by solvothermal method, which further transformed to porous ZnO–NiO composite micropolyhedra without significant alterations in shape by calcination in air. Those products were characterized by powder X-ray diffraction (XRD), field emission scanning electron microscopy (SEM), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), infrared spectroscopy (IR) and gas adsorption measurements. The catalytic activity of ZnO–NiO composites for the thermal decomposition of ammonium perchlorate (AP) was investigated. The result shows that all ZnO–NiO composites efficiently catalyzed the thermal decomposition of AP, and NiO–ZnO composite hollow octahedrons have the highest catalytic efficiency compared with that of most materials reported to now, indicating that porous ZnO–NiO composite micropolyhedra could be a promising candidate material for application in AP-based propellant.     

Co3O4/NiO/C composites derived from zeolitic imidazolate frameworks (ZIFs) as high-performance anode materials for Li-ion batteries

Journal of Solid State Electrochemistry - In this paper, Co3O4/NiO/C composites were prepared by in situ co-precipitation and heat treatment with Zn/Co-ZIF-derived N-doped porous carbon as carbon...     

Nickel oxide/expanded graphite nanocomposite electrodes for supercapacitor application

Nickel oxide/expanded graphite (NiO/EG) nanocomposites with different loading of EG were prepared through chemically depositing Ni(OH)₂ in EG followed by thermal annealing and characterized by scanning electron microscopy (SEM), powder X-ray diffraction (XRD), Brunauer–Emmet–Teller (BET) isotherm and electrochemical measurements. The prepared NiO/EG composites were found to be crystalline and highly porous with high specific surface area and pore volume. SEM analysis reveals uniform porous morphology for NiO in the NiO/EG-60 nanocomposites which shows good specific capacitance (510?F?g^?1) at a current density of 100?mA?g^?1 in 6?mol?L^?1 KOH measured by chronopotentiometry employing a three-electrode system. The specific capacitance retention of the NiO/EG-60 nanocomposites was found to be ca. 95% after 500 continuous galvanostatic charge–discharge cycles, indicating that the NiO/EG nanocomposites can become promising electro-active materials for supercapacitor application.     

NiO/CNTs derived from metal-organic frameworks as superior anode material for lithium-ion batteries

In this work, porous NiO microspheres interconnected by carbon nanotubes (NiO/CNTs) were successfully fabricated by the pyrolysis of nickel metal-organic framework precursors with CNTs and evaluated as anode materials for lithium-ion batteries (LIBs). The structures, morphologies, and electrochemical performances of the samples were characterized by X-ray diffraction, N₂ adsorption-desorption, field emission scanning electron microscopy, cyclic voltammetry, galvanostatic charge/discharge tests, and electrochemical impedance spectroscopy, respectively. The results show that the introduction of CNTs can improve the lithium-ion storage performance of NiO/CNT composites. Especially, NiO/CNTs-10 exhibits the highest reversible capacity of 812 mAh g^?1 at 100 mA g^?1 after 100 cycles. Even cycled at 2 A g^?1, it still maintains a stable capacity of 502 mAh g^?1 after 300 cycles. The excellent electrochemical performance of NiO/CNT composites should be attributed to the formation of 3D conductive network structure with porous NiO microspheres linked by CNTs, which benefits the electron transfer ability and the buffering of the volume expansion during the cycling process.     

双通氧化铝模板制备及其填充NiO的研究

制备具有双通纳米孔道填充过渡金属氧化物NiO的氧化铝模板，初步表征其电化学性质，结果发现，该氧化铝模板的纳米孔道结构均匀，孔道直径约为50nm，所填充的纳米NiO层厚度相对均匀，并具有较好的循环稳定性。     

微波辅助合成石墨烯/氧化镍复合材料及其表征

本文通过微波辅助的方法,快速而有效地在热膨胀石墨烯(RG)的缺陷上原位合成氧化镍纳米颗粒,形成石墨烯/氧化镍复合材料(RG/NiO)。利用X-射线衍射(XRD),拉曼光谱(Raman),傅里叶变换红外(FTIR),扫描电镜(SEM),透射电镜(TEM),热重-差热(TGA-DSC)对所制备样品的结构、形貌和NiO在复合材料中的含量进行表征。结果表明,热膨胀石墨烯层数约7~8层,层间距约为0.35 nm,缺陷多,在水热和微波处理后抗氧化性明显变差。复合材料中氧化镍颗粒平均粒径为25 nm,均匀而密集地分散在石墨烯平面上,同时在复合材料中的含量为19.8%。     

微波辅助合成石墨烯/氧化镍复合材料及其表征

本文通过微波辅助的方法,快速而有效地在热膨胀石墨烯(RG)的缺陷上原位合成氧化镍纳米颗粒,形成石墨烯/氧化镍复合材料(RG/NiO)。利用X-射线衍射(XRD),拉曼光谱(Raman),傅里叶变换红外(FTIR),扫描电镜(SEM),透射电镜(TEM),热重-差热(TGA-DSC)对所制备样品的结构、形貌和NiO含量在复合材料中的含量进行表征。结果表明,热膨胀石墨烯层数约7~8层,层间距约为0.35nm,缺陷多,在水热和微波处理后抗氧化性明显变差。复合材料中氧化镍颗粒平均粒径为25nm,均匀而密集地分散在石墨烯平面上,同时在复合材料中的含量为19.8%。     

Graphene sheet/porous NiO hybrid film for supercapacitor applications

We report the preparation of a nickel-foam-supported graphene sheet/porous NiO hybrid film by the combination of electrophoretic deposition and chemical-bath deposition. The obtained graphene-sheet film of about 19 layers was used as the nanoscale substrate for the formation of a highly porous NiO film made up of interconnected NiO flakes with a thickness of 10-20 nm. The graphene sheet/porous NiO hybrid film exhibits excellent pseudocapacitive behavior with pseudocapacitances of 400 and 324 F g(-1) at 2 and 40 A g(-1), respectively, which is higher than those of the porous NiO film (279 and 188 F g(-1) at 2 and 40 A g(-1)). The enhancement of the pseudocapacitive properties is due to reinforcement of the electrochemical activity of the graphene-sheet film.     

A New Layered Photocathode with Porous NiO Nanosheets: An Effective Candidate for p‐Type Dye‐Sensitized Solar Cells

Herein, with the purpose of improving the efficiency of p‐type dye‐sensitized solar cells (DSSCs), a new layered photocathode (LP) is fabricated from irregular overlapping wrinkled porous NiO nanosheets. The LP was sensitized by using a commonly used dye, coumarin 343(C343), and then assembled into p‐type DSSCs through coupling with a platinum photoanode. Photoelectochemical characterization showed that the LP cell exhibited a clearly enhanced power‐conversion efficiency (by a factor of 4) compared with a cell with a NiO‐nanoparticle photocathode (NP). This excellent performance could be attributed to the overlapping layered structure, which favored hole transport, as confirmed by electrochemical impedance spectroscopy, and to the large surface area of the porous NiO nanosheets, which were favorable for dye adsorption.