CuInS2量子点阻变效应

采用改进的热分解法制备了具有半导体效应的CuInS₂量子点,量子点尺寸均匀、大小为4.2 nm。组装的Au/CuInS₂/FTO阻变存储器件表现出典型的双极性阻变特点,其开态电压为-3.8 V,关态电压为4 V,ON/OFF开关比约为10³。对器件的I-V特性曲线线性拟合发现,器件的阻变机制在高阻态时表现为空间限制电荷（SCLC）传导机制,在低阻态时表现为欧姆传导机制。器件的阻变特性主要是由于电荷被CuInS₂薄膜中的缺陷产生的势阱捕获导致。通过调节陷阱势垒高度引起电荷在陷阱中移动,导致导电通路的产生和断裂,使器件处于高阻态和低阻态。     

溶胶凝胶法制备TiO2@Cf柔性忆阻器交叉开关

以碳纤维作为柔性衬底和电极材料,通过溶胶凝胶法在其表面镀覆TiO₂阻变活性层,进而通过“十”字搭接制备成柔性纤维忆阻器（TiO₂@C_f）。采用X射线衍射、扫描电子显微镜、X射线光电子能谱等测试手段对TiO₂@C_f结构进行表征并对其忆阻特性及阻变机理进行研究。结果表明：碳纤维上的TiO₂涂层为锐钛矿型晶体结构,其氧空位的浓度约为19.5%;制备的TiO 2@C_f柔性忆阻器为突变型忆阻器,其高低阻态阻值开关比可达10⁴;经过疲劳耐受性测试,忆阻器件的高低阻态开关比稳定在2个数量级左右。TiO₂@C_f忆阻器的机理表现为：在高阻态和低阻态时是以欧姆导电为主导的载流子输运机制,其阻态转变机制与氧空位导电细丝的形成和断裂有关。制备的TiO₂@C_f柔性忆阻器在一定程度上具有柔性弯曲变形,同时满足可编织、穿戴等功能。     

SnS2/GCP（石墨烯复合粉末）微米复合材料作为锂离子电池负极材料的电化学性能

以石墨烯复合粉末为添加剂,采用一步水热法制备了一种SnS₂/GCP微米复合材料。在所得到的复合材料中,SnS₂纳米片相互缠绕组成多孔球状SnS₂颗粒,石墨烯复合粉末均匀的包裹在球状SnS₂颗粒表面。将所制备的SnS₂/GCP微米复合材料用作锂离子电池负极材料测其电化学性能。结果显示,在0.1 A·g^-1的电流密度下可逆比容量为795.6 mAh·g^-1,循环100次后比容量损失不到1%。相比于SnS₂其比容量和循环稳定性得到了明显改善,主要是由于石墨烯复合粉末的加入,不仅缓解了SnS₂颗粒在充放电过程中的团聚和体积膨胀,而且还提高了SnS₂颗粒的电导率。     

SnS2/GCP(石墨烯复合粉末)微米复合材料作为锂离子电池负极材料的电化学性能

以石墨烯复合粉末为添加剂,采用一步水热法制备了一种SnS₂/GCP微米复合材料。在所得到的复合材料中,SnS₂纳米片相互缠绕组成多孔球状SnS₂颗粒,石墨烯复合粉末均匀的包裹在球状SnS₂颗粒表面。将所制备的SnS₂/GCP微米复合材料用作锂离子电池负极材料测其电化学性能。结果显示,在0.1 A·g^-1的电流密度下可逆比容量为795.6 mAh·g^-1,循环100次后比容量损失不到1%。相比于SnS₂其比容量和循环稳定性得到了明显改善,主要是由于石墨烯复合粉末的加入,不仅缓解了SnS₂颗粒在充放电过程中的团聚和体积膨胀,而且还提高了SnS₂颗粒的电导率。     

Cu(bpy)2+2与鸟嘌呤及鸟苷相互作用的研究

在中性磷酸盐缓溶冲液中，用电化学和荧光光谱法研究了Cu(bpy)²⁺₂与鸟嘌呤和鸟苷的相互作用。结果表明鸟嘌呤和鸟苷与Cu(bpy)²⁺₂的配位比均为1∶1，配位常数分别为4.62×10⁴ L/mol和1.96×10⁴ L/mol。紫外光谱电化学实验进一步表明，鸟嘌呤或鸟苷与Cu(bpy)²⁺₂发生了相互作用。     

乙醇/Tris-水中Cu(Ⅱ)对SDS和DNA增强[Ru(bpy)2(dppz)]2+光致发光的调控

应用荧光光谱、荧光显微镜和伏安法研究了乙醇/水体系中Cu(Ⅱ)对十二烷基硫酸钠(SDS)和鱼精DNA增强[Ru(bpy)₂(dppz)]²⁺(bpy=2,2′-联吡啶, dppz=邻联二吡啶[3,2-a:2′,3′-c]吩嗪)光致发光的调控。结果表明, 在乙醇/三羟甲基氨基甲烷(Tris)-水 (V_乙醇:V_Tris=1:5)体系中, DNA和阴离子表面活性剂SDS均能增强[Ru(bpy)₂(dppz)]²⁺的光致发光, 其与[Ru(bpy)₂(dppz)]²⁺间的键合常数分别为5.5×10⁵和4.2×10² L·mol^-1;Cu(Ⅱ)离子能通过DNA和SDS介导的光诱导电子转移淬灭乙醇/水溶液中[Ru(bpy)₂(dppz)]²⁺的光致发光, DNA介导的Stern-Volmer淬灭常数为2.0×10⁵ L·mol^-1, 远远大于SDS介导的淬灭常数(9.0×10³ L·mol^-1)。此外, 结合SDS、DNA和Cu(Ⅱ)对[Ru(bpy)₂(dppz)]²⁺在铟锡氧化物(ITO)电极上发生的氧化还原反应的影响, 进一步探讨了乙醇/Tris-水中Cu(Ⅱ)对SDS和DNA增强[Ru(bpy)₂(dppz)]²⁺光致发光的调控机理。该研究有助于更好地理解DNA嵌入剂的发光和淬灭机制, 为生物分子光开关的构建提供新思路。     

多金属氧酸盐修饰的过渡金属配合物的催化效果和电化学行为

基于水热技术,合成了多金属氧酸盐修饰的2种新的过渡金属配合物[Cu（dmbipy）²（SiW¹²O⁴⁰）][Cu（dmbipy）（H₂O）₃]·3H₂O（1）和{（Hdmphen）²[Ag₂（dmphen）²（SiW¹²O⁴⁰）]}_n（2）（dmbipy=4,4’-二甲基-2,2’-联吡啶,dmphen=2,9-二甲基-1,10-菲咯啉）。配合物1的最小不对称单元包含2种不同的Cu（Ⅱ）单元,其中Cu（Ⅱ）离子都采用了五配位的模式,并且水分子也参与了配位。氢键将不同的Cu（Ⅱ）单元连接形成了一维链,并延伸至二维层。在配合物2中,多金属氧酸盐连接Ag（Ⅱ）离子形成一维链。氢键和π…π堆积作用将一维链拓展成了二维层。     

金属离子对联吡啶钌电致化学发光影响的研究

在玻碳电极上, 联吡啶钌[Ru(bpy)₃^2＋]于＋1.50 V (vs. Ag/AgCl)左右被氧化为Ru(bpy)₃^3＋, 该氧化态离子与碱性水溶液中(pH 8.2)的OH•反应生成激发态的[Ru(bpy)₃^2＋*]而发光. 研究比较了15种金属离子对Ru(bpy)₃^2＋碱性水溶液电致化学发光的影响, 并对这些影响进行了初步的解释.     

氢过碘酸）合银（III）配离子氧化L-脯氨酸的反应动力学及机理

L-脯氨酸独有的亚胺基使其在生物医药领域具有许多独特的功能,并广泛用作不对称有机化合物合成的有效催化剂。本文在碱性介质中研究了二（氢过碘酸）合银（III）配离子氧化 L-脯氨酸的反应。经质谱鉴定,脯氨酸氧化后的产物为脯氨酸脱羧生成的 γ-氨基丁酸盐;氧化反应对脯氨酸及Ag(III) 均为一级;二级速率常数 k′ 随 [IO₄^-] 浓度增加而减小,而与 [OHˉ] 的浓度几乎无关;推测反应机理应包括 [Ag(HIO₆)₂]^5-与 [Ag(HIO₆)(H₂O)(OH)]^2-之间的前期平衡,两种Ag（III）配离子均作为反应的活性组分,在速控步被完全去质子化的脯氨酸平行地还原,两速控步对应的活化参数为： k₁ (25 ^oC)＝1.87±0.04（mol·L^-1)^-1s^-1,∆ H₁^≠＝45±4 kJ · mol^-1, ∆ S₁^≠＝-90±13 J· K^-1·mol^-1 and k₂ (25 ^oC) ＝3.2±0.5（mol·L^-1)^-1s^-1, ∆ H₂^≠＝34±2 kJ · mol^-1, ∆ S₂^≠＝-122 ±10 J· K^-1·mol^-1。本文第一次发现 [Ag(HIO₆)₂]^5-配离子也具有氧化反应活性。     

层状钴氧化物Bi2-xAgxSr2Co2O8-δ的高温热电性能及XPS研究

采用固相反应法制备了组成为Bi_2-xAg_xSr₂Co₂O_8-δ(x=0.0, 0.4, 0.8,略写为BAC-222)的层状钴氧化物陶瓷。利用X-射线光电子能谱考察该类化合物的电子结构,结果表明钴离子以Co³⁺和Co⁴⁺混合价态形式存在,n_Co⁴⁺/n_Co³⁺的比例随着Ag掺杂的量增加而增加。O1s光电子谱显示在所有样品中均存在点阵氧和吸附氧。热电性能测试结果显示,随着Ag掺杂量的增加,电导率显著增加而Seebeck系数几乎保持不变,Ag的引入极大的影响了BAC-222的电子输运性质,其功率因子在1 123 K时达到了1.23×10^-4 W·m^-1·K^-2,是一种具有很好应用前景的热电材料。     

Impact of Top Electrodes (Cu,Ag, and Al) on Resistive Switching behaviour of Cu-rich Cu2ZnSnS4 (CZTS) Ideal Kesterite

Cu₂ZnSnS₄ (CZTS) active material-based resistive random-access memory (RRAM) devices are investigated to understand the impact of three different Cu, Ag, and Al top electrodes. The dual resistance switching (RS) behaviour of spin coated CZTS on ITO/Glass is investigated up to 10² cycles. The stability of all the devices (Cu/CZTS/ITO, Ag/CZTS/ITO, and Al/CZTS/ITO) is investigated up to 10³ sec in low- (LRS) and high- (HRS) resistance states at 0.2 V read voltage. The endurance up to 10² cycles with 30 msec switching width shows stable write and erase current. Weibull cumulative distribution plots suggest that Ag top electrode is relatively more stable for set and reset state with 33.61 and 25.02 shape factors, respectively. The charge carrier transportation is explained by double logarithmic plots, Schottky emission plots, and band diagrams, substantiating that at lower applied electric field intrinsic copper ions dominate in Cu/CZTS/ITO, whereas, at higher electric filed, top electrodes (Cu and Ag) dominate over intrinsic copper ions. Intrinsic Cu⁺ in CZTS plays a decisive role in resistive switching with Al electrode. Further, the impedance spectroscopy measurements suggest that Cu⁺ and Ag⁺ diffusion is the main source for the resistive switching with Cu and Ag electrodes.     

Synthesis of Ag2O and Ag co-modified flower-like SnS2 composites with enhanced photocatalytic activity under solar light irradiation

Three-dimensional Ag₂O and Ag co-modified flower-like SnS₂ composites have been synthesized through a facile hydrothermal and photoreduction process. The physical and chemical properties of Ag₂O and Ag co-modified flower-like SnS₂ composites were carefully studied by using XRD, SEM, TEM, UV–vis diffuse reflectance spectra (DRS) and XPS. The photocatalytic activity of the as-prepared products was evaluated by photocatalytic decolorization of Rhodamine B (Rh B) aqueous solution at ambient temperature under solar light irradiation. The photocatalytic result shows that Ag₂O and Ag co-modified flower-like SnS₂ composites exhibit enhanced photocatalytic activity compared with that of pure SnS₂. Three of the Ag₂O and Ag co-modified flower-like SnS₂ composites form the Z-scheme systems, because of their unique charge-carrier transfer process, the oxidation/reduction ability of photogenerated holes and electrons could be enhanced. Therefore, the new Ag₂O and Ag co-modified flower-like SnS₂ composites possess a favorable photocatalytic activity, and it can be a promising candidate for the solar energy conversion process.     

Züchtung und Untersuchung von Einkristallen in den pseudobinären Systemen ABS2?SnS2 (A = Cu,Ag; B = Al,Cr)

Preparation and Characterization of Single Crystals in the Pseudo-binary Systems ABS₂? SnS₂ (A = Cu, Ag; B = Al, Cr) In the pseudo-binary systems ABS₂? SnS₂ (A = Cu, Ag; B = Al, Cr) single crystals were grown by chemical transport using AlCl₃/I₃ mixtures as transporting agents. Characterization of the crystals was done by electron microprobe analyses and X-ray methods. The composition A_1?x□_x[B_1?xSb_1+x]S₄ was found for the non-stoichiometric phases. The compounds are normal spinels, the space group is Fd3m. The results of least squares refinement using single crystal X-ray data are reported.     

Effects of a controlled N2 and O2 addition to Ar on the analytical parameters of the GD-OES

The influence of the controlled addition of N₂ and of O₂ to Ar on the analytical parameters of a dc glow discharge has been investigated for bulk samples of the pure metals Al, Ti, Fe, Ni, Cu, and Ag. The constant voltage discharge mode at 1000 V was applied with a mean power of about 1 W/mm². The N₂ and O₂ concentrations in the discharge gas Ar were varied in the range 0–3 mass-%, corresponding to a partial pressure of about 4 · 10^?3 hPa. The general effect of the gaseous addition is the decrease of the sputtering rate with an increasing concentration of N₂ or O₂. Atomic processes, which might be responsible for the observed effects, are discussed.     

Effects of a controlled N2 and O2 addition to Ar on the analytical parameters of the GD-OES

The influence of the controlled addition of N₂ and of O₂ to Ar on the analytical parameters of a dc glow discharge has been investigated for bulk samples of the pure metals Al, Ti, Fe, Ni, Cu, and Ag. The constant voltage discharge mode at 1000 V was applied with a mean power of about 1 W/mm². The N₂ and O₂ concentrations in the discharge gas Ar were varied in the range 0–3 mass-%, corresponding to a partial pressure of about 4 · 10^–3 hPa. The general effect of the gaseous addition is the decrease of the sputtering rate with an increasing concentration of N₂ or O₂. Atomic processes, which might be responsible for the observed effects, are discussed.     

Sol-Gel Synthesis of Metal Nanoclusters-Silica Composite Films

In a program on the development of metal nanoclusters in sol-gel derived thin films, attempts were made to synthesize pure and mixed metal clusters, control the cluster size and increase the volume fract f the clusters. Thus, Ag, Cu and Ag-Cu nanoclusters were prepared in silica films using dip- and spin-coating techniques. The annealing of Ag/SiO₂ films in different atmospheres (air, argon and 5% H₂-95% N₂ gas) caused modifications of Ag nanoclusters resulting in changes in their surface plasmon resonance (SPR) peak positions. The Cu and Ag-Cu codoped films were annealed in reducing atmosphere (5% H₂-95% N₂ gas). In order to prepare Cu nanoclusters of different sizes, the concentrations of Cu in Cu/SiO₂ composite films were varied from 8 to 30 mol% and annealed at 800°C for different times for growth. The size of the Cu nanoclusters was measured from the half band width of Cu SPR peak (appearing within 570–557 nm range) and X-ray diffraction. In this way Cu-nanoclusters of size ranges from about 3.5 to 10 nm (average diameters) were prepared . The Ag-Cu nanocluster-containing silica films show the existence of both Ag and Cu SPR peaks with some blue shifting in comparison with to their pure analogues depending on the Ag:Cu ratio.     

Physical and optical properties of the quaternary sulfides SrCu2MS4 and EuCu2MS4 (M=Ge and Sn)

Four quaternary sulfides SrCu₂MS₄ and EuCu₂MS₄ (M=Ge and Sn) were prepared from a thoroughly ground mixture of EuS or SrS, Cu, or Sn, and S in stoichiometric proportions. Electrical conductivity measurements on pressed pellets showed that all the phases are semiconductors. The optical band gaps were assessed at 2.8 eV for SrCu₂GeS₄, 2.1 eV for SrCu₂SnS₄, 2.2 eV for EuCu₂SnS₄, and 1.6 eV for EuCu₂GeS₄. Both Sr-based compounds present a temperature-independent paramagnetism, of about +135×10⁻⁶ and +92×10⁻⁶ emu/mol, for SrCu₂SnS₄ and SrCu₂GeS₄, respectively. In the case of the europium compounds, they follow a Curie-Weiss dependence above 1.8 K (EuCu₂GeS₄) and above 4 K (for EuCu₂SnS₄), with values of the magnetic effective moment μ_eff and the Curie-Weiss temperature Θ, equal to 6.27 μ_B and −2.8 K for EuCu₂GeS₄, and 6.81 μ_B and +0.7 K, for EuCu₂SnS₄. The experimental magnetic moments confirm that the europium ion is in divalent state, similar to Sr in the related compounds.     

Microstructure of metallic copper nanoparticles/metallic disc interface in metal–metal bonding using them

This paper describes a metal–metal bonding technique using metallic Cu nanoparticles prepared in aqueous solution. A colloid solution of metallic Cu particles with a size of 54 ± 15 nm was prepared by reducing Cu²⁺ (0.01 M (CH₃COO)₂Cu) with hydrazine (0.6 M) in the presence of stabilizers (5 × 10^?4 M citric acid and 5 × 10^?3 M cetyltrimethylammonium bromide) in water at room temperature in air. Discs made of metallic materials (Cu, Ni/Cu, or Ag/Ni/Cu) were successfully bonded under annealing at 400 °C and pressurizing at 1.2 MPa for 5 min in H₂ gas with help of the metallic Cu particle powder. Shear strength required for separating the bonded discs was 27.9 ± 3.9 for Cu discs, 28.1 ± 4.1 for Ni/Cu discs, and 13.8 ± 2.6 MPa for Ag/Ni/Cu discs. Epitaxial crystal growth promotes on the discs with a good matching for the lattice constants between metallic nanoparticles and metallic disc surfaces, which leads to strong bonding. Copyright © 2013 John Wiley & Sons, Ltd.