Detection of Human Interleukine‐2 Gene Using a Label‐Free Electrochemical DNA Hybridization Biosensor on the Basis of a Non‐Inosine Substituted Probe

The human interleukine‐2 gene (hIL‐2) is detected with a label‐free DNA hybridization biosensor using a non‐inosine substituted probe. The sensor relies on the immobilization of a 20‐mer antisense single strand oligonucleotide (chIL‐2) related to the human interleukine‐2 gene on the pencil graphite electrode (PGE) as a probe. The guanine oxidation signal was monitored using anodic differential pulse voltammetry (ADPV). The electrochemical pretreatment of the polished PGE at 1.80 V for 5 min is suggested. Then, 5 min immobilization at 0.50 V was found as the optimum condition for immobilization of the probe. The electrochemical detection of hybridization between chIL‐2 and hIL‐2 as a target was accomplished. The selectivity of the biosensor was studied using noncomplementary oligonucleotides. Diagnostic performance of the biosensor is described and the detection limit is found 36 pg/μL.     

Developing a Nano‐Biosensor for DNA Hybridization Using a New Electroactive Label

Development of electrochemical DNA hybridization biosensors based on carbon paste electrode (CPE) and gold nanoparticle modified carbon paste electrode (NGMCPE) as transducers and ethyl green (EG) as a new electroactive label is described. Electrochemical impedance spectroscopy and cyclic voltammetry techniques were applied for the investigation and comparison of bare CPE and NGMCPE surfaces. Our voltammetric and spectroscopic studies showed gold nanoparticles are enable to facilitate electron transfer between the accumulated label on DNA probe modified electrode and electrode surface and enhance the electrical signals and lead to an improved detection limit. The immobilization of a 15‐mer single strand oligonucleotide probe on the working electrodes and hybridization event between the probe and its complementary sequence as a target were investigated by differential pulse voltammetry (DPV) responses of the EG accumulated on the electrodes. The effects of some experimental variables on the performance of the biosensors were investigated and optimum conditions were suggested. The selectivity of the biosensors was studied using some non‐complementary oligonucleotides. Finally the detection limits were calculated as 1.35×10^?10 mol/L and 5.16×10^?11 mol/L on the CPE and NEGCPE, respectively. In addition, the biosensors exhibited a good selectivity, reproducibility and stability for the determination of DNA sequences.     

Differential Pulse Voltammetric Detection of Hepatitis C Virus 1a Oligonucleotide Chain by a Label‐Free Electrochemical DNA Hybridization Biosensor Using Consensus Sequence of Hepatitis C Virus 1a Probe on the Pencil Graphite Electrode

The short sequence related to hepatitis C virus (HCV1) is detected by a label‐free DNA hybridization biosensor. The sensor relies on the immobilization of a 20‐mer oligonucleotide containing 2 guanine and 11 cytosine bases denoted PHCV1 as probe on the pencil graphite electrode (PGE). The hybridization event was monitored by differential pulse voltammetry (DPV) using the guanine signal. The selectivity of the biosensor was studied using some noncomplementary oligonucleotides. Diagnostic performance of the biosensor is described and the detection limit was found to be 6.5 nM.     

A Novel DNA Probe Based on Molecularly Imprinted Polymer Modified Electrode for the Electrochemical Monitoring of DNA

A DNA probe that was based on methylene blue (MB) imprinted polyvinyl pyridine polymer (MIP) modified carbon paste electrodes were developed for the first time for electrochemical monitoring of DNA. Probes were built up by adsorbing MB onto modified electrodes prior to DNA immobilization. It was shown that DNA strongly immobilizes on MIP modified electrodes when MB was adsorbed in advance of DNA immobilization. The performance of the MB imprinted polymer modified carbon paste electrodes (MIP‐CPE) to rebind the template molecule (MB) were compared to those of control polymer modified (non‐imprinted polymer NIP‐CPE) and bare (CPE) electrodes. Electrochemical signal resulting from the oxidation of guanine moiety of the immobilized probe DNA was high enough on the constructed platform, implicating that probes of this kind could be favorably used for DNA analysis. These probes exhibited high selectivity for its complementary DNA sequences (target). HBV‐DNA hybridization was studied to evaluate the selectivity of the probes for complementary, non‐complementary and mismatch sequences. The detection limit of the probe for the target DNA was 8.72 µg/mL (1.38 µM), which was better than those attained by some earlier DNA sensor studies.     

DNA Hydrolysis and Voltammetric Determination of Guanine and Adenine Using Different Electrodes

Abstract

This work reports the development of a biosensor method for the label‐free detection of specific DNA sequences. In the initial phase, square wave voltammetry (SWV) was used in a comparative investigation into the electrochemical oxidation of purines (guanine and adenine) and DNA fragments at various electrode surfaces: carbon paste (CPE), glassy carbon electrode (GCE), and gold (AuE). Relative to the carbon electrodes, an approximate 4.0‐fold, 6.0‐fold, and 3.25‐fold increase in the anodic response was observed when guanine, adenine, and hydrolyzed DNA, respectively, were measured on the AuE. It was shown that the guanine and adenine bases could be successfully determined by use of SWV for a deoxyribonucleic acid sample following acid hydrolysis. This label‐free detection of hydrolyzed DNA on gold electrodes has significant advantages over methods using existing carbon electrode materials because of its higher sensitivity and the potential applicability of microfabrication techniques for the production of the requisite gold electrodes.

In another phase of development, the times and conditions for DNA hydrolysis and purine release were investigated. It was shown that under optimal conditions, trace levels of the purine bases could be readily detected following 20 min of hydrolysis at room temperature. The proposed method can be used to estimate the guanine and adenine contents in DNA with in a linear range of 5–30 ng ml^?1.

Finally, when appropriate probe sequences were first adsorbed on the surface of the screen‐printed gold electrode (SPGE), this electrochemical biosensor could be used to specifically detect sequences from ss corona virus aviair following hybridization and hydrolysis reactions on the sensor surface. No enhancement of the voltammetric response was observed when the sensor was challenged with a non‐complementary DNA sequence.     

Label‐Free Bioelectronic Detection of Point Mutation by Using Peptide Nucleic Acid Probes

An electrochemical hybridization biosensor based on peptide nucleic acid (PNA) probes with a label‐free protocol is described. The detection of PNA‐DNA and DNA‐DNA hybridizations were accomplished based on the oxidation signal of guanine by using differential pulse voltammetry (DPV) at carbon paste electrode (CPE). It was observed that the oxidation signals of guanine obtained from the PNA and DNA probe modified CPEs were higher than those obtained from the PNA‐DNA and DNA‐DNA hybrid modified CPEs due to the accessible unbound guanine bases. The detection of hybridization between PNA probe and point mutation containing DNA target sequences was clearly observed due to the difference of the oxidation signals of guanine bases, because the point mutation was guanine nearly at the middle of the sequence. The effect of the DNA target concentration on the hybridization signal was also observed. The PNA probe was also challenged with excessive and equal amount of noncomplementary DNA and also mixtures of point mutation and target DNA.     

Label‐Free and Label Based Electrochemical Detection of Hybridization by Using Methylene Blue and Peptide Nucleic Acid Probes at Chitosan Modified Carbon Paste Electrodes

A chitosan modified carbon paste electrode (ChiCPE) based DNA biosensor for the recognition of calf thymus double stranded DNA (dsDNA), single stranded DNA (ssDNA) and hybridization detection between complementary DNA oligonucleotides is presented. DNA and oligonucleotides were electrostatically attached by using chitosan onto CPE. The amino groups of chitosan formed a strong complex with the phosphate backbone of DNA. The immobilized probe could selectively hybridize with the target DNA to form hybrid on the CPE surface. The detection of hybridization was observed by using the label‐free and label based protocols. The oxidation signals of guanine and adenine greatly decreased when a hybrid was formed on the ChiCPE surface. The changes in the peak currents of methylene blue (MB), an electroactive label, were observed upon hybridization of probe with target. The signals of MB were investigated at dsDNA modified ChiCPE and ssDNA modified ChiCPE and the increased peak currents were observed, in respect to the order of electrodes. The hybridization of peptide nucleic acid (PNA) probes with the DNA target sequences at ChiCPE was also investigated. Performance characteristics of the sensor were described, along with future prospects.     

Developing an electrochemical deoxyribonucleic acid (DNA) biosensor on the basis of human interleukine-2 gene using an electroactive label

Development of an electrochemical DNA biosensor based on a human interleukine-2 (IL-2) gene probe, using a pencil graphite electrode (PGE) as transducer and methylene blue (MB) as electroactive label is described. The sensor relies on the immobilization of a 20-mer single stranded oligonucleotide probe (hIL-2) related to the IL-2 gene on the electrode. The hybridization between the probe and its complementary sequence (chIL-2) as the target was studied by square wave voltammetry (SWV) of MB accumulated on the PGE. In this approach the extent of hybridization is evaluated on the basis of the difference between SWV signals of MB accumulated on the probe-PGE and MB accumulated on the probe-target-PGE. Some hybridization experiments with non-complementary oligonucleotides were carried out to assess whether the suggested DNA sensor responds selectively to the target. Some experimental variables affecting the performance of the biosensor including: polishing of PGE, its electrochemical activation conditions (i.e., activation potential and activation time) and probe immobilization conditions on the electrodes (i.e., immobilization potential and time) were investigated and the optimum values of 1.80 V and 300 s for PGE activation, and −0.5 V and 400 s for the probe immobilization on the electrode were suggested.     

Lable‐Free Electrochemical DNA Sensor Based on Gold Nanoparticles/Poly(neutral red) Modified Electrode

We present a new strategy for the label‐free electrochemical detection of DNA hybridization based on gold nanoparticles (AuNPs)/poly(neutral red) (PNR) modified electrode. Probe oligonucledotides with thiol groups at the 5‐end were covalently linked onto the surface of AuNPs/PNR modified electrode via S‐Au binding. The hybridization event was monitored by using differential pulse voltammetry (DPV) upon hybridization generates electrochemical changes at the PNR‐solution interface. A significant decrease in the peak current was observed upon hybridization of probe with complementary target ssDNA, whereas no obvious change was observed with noncomplementary target ssDNA. And the DNA sensor also showed a high selectivity for detecting one‐mismatched and three‐mismatched target ssDNA and a high sensitivity for detecting complementary target ssDNA, the detection limit is 4.2×10^?12 M for complementary target ssDNA. In addition, the DNA biosensor showed an excellent reproducibility and stability under the DNA‐hybridization conditions.     

Prostate Cancer Biomarker Detection with Carbon Nanotubes Modified Screen Printed Electrodes

DNA hypermethylation is an epigenetic alteration and a promising biomarker for early prostate cancer detection. Simple, sensitive, easy to handle and rapid detection methodologies are imperative for point of care diagnostics especially for cancer. Herein, we describe for the first time a regenerable and compatible electrochemical biosensor for detection of Glutathione S‐Transferase P‐1 (GSTP‐1) gene hypermethylation related to prostate cancer via DNA hybridization onto the disposable Carbon and Multi Walled Carbon Nanotubes (MWCNT) Screen Printed Electrodes (SPEs). In the study, capture probes were adsorbed onto the SPEs by simple passive adsorption and then hybridization was achieved by sending the complementary target onto the probe‐modified electrodes. The selectivity of the biosensor was proved by control studies. Differential Pulse Voltammetry (DPV) technique was used to detect hybridization via guanine oxidation signals changes. The total time of the optimized method was nearly 1h, measurements took for less than 1 min, and the biosensor response was stable up to 40 days of storage period at 4 °C. The main advantages of the biosensor are very low detection limit (picomolar range) and capability of reusing the biosensor for at least 3 times after very simple regeneration process that is a unique property to reduce the cost of the assay. In addition, this is the first study that demonstrates the detection of GSTP‐1 hypermethylation electrochemically by using SPEs in order to create point of care diagnostics. The optimum parameters for the biosensor, as well as its future prospects to enhance the performance of DNA biosensors were also presented.     

Fabrication of a Sensitive Impedance Biosensor of DNA Hybridization Based on Gold Nanoparticles Modified Gold Electrode

In this work, we report on the preparation of a simple, sensitive DNA impedance sensor. Firstly gold nanoparticles were electrodeposited on the surface of a gold electrode, and then probe DNA was immobilized on the surface of gold nanoparticles through a 5′‐thiol‐linker. Electrochemical impedance spectroscopy (EIS) was used to investigate probe DNA immobilization and hybridization. Compared to the bare gold electrode, the gold nanoparticles modified electrode could improve the density of probe DNA attachment and the sensitivity of DNA sensor greatly. The difference of electron transfer resistance (ΔR_et) was linear with the logarithm of complementary oligonucleotides sequence concentrations in the range of 2.0×10^?12 to 9.0×10^?8 M, and the detection limit was 6.7×10^?13 M. In addition, the DNA sensor showed a fairly good reproducibility and stability during repeated regeneration and hybridization cycles.     

Indigo Carmine as New Label in PNA Biosensor for Detection of Short Sequence of p53 Tumor Suppressor Gene

A new electrochemical PNA hybridization biosensor for detection of a 15‐mer sequence unique to p53 using indigo carmine (IC) as an electrochemical detector is described in this work. This genosensor is based on the hybridization of target oligonucleotide with its complementary probe immobilized on the gold electrode by self‐assembled monolayer formation. Because this label is electroactive in acidic medium, the interaction between IC and short sequence of p53 is studied by differential pulse voltammety (DPV) in 0.1 M H₂SO₄. The results of electrochemical impedance spectroscopy and cyclic voltammetry in the solution of [Fe(CN)₆]^3?/4? shows no breakage in PNA‐DNA duplex. A decrease in the voltammetric peak currents of IC is observed upon hybridization of the probe with the target DNA. The influence of probe concentration on effective discrimination against non‐complementary oligonucleotides is investigated and a concentration of 10^?7 M is selected. The diagnostic performance of the PNA sensor is described and the detection limit is found to be 4.31×10^?12 M.     

Voltammetric detection of uridin diphosphate glucuronosyl transferase 1A9 (UGT1A9) gene corresponding oligonucleotide covering promoter region from −268 to −280 including (A/T) polymorphism at position −275 and optimization of the detection factors

In this study, we developed a new peptide nucleic acid (PNA) biosensor for detection of a single nucleotide polymorphism (SNP) in the UGT1A9 gene promoter region via electrochemical assay. The sensor relies on the immobilization of a 13-mer single stranded PNA probe related to the UGT1A9 gene on the Au electrode (AuE). The hybridization between the probe and its complementary sequence (DcUG275) as the target was studied by differential pulse voltammetry (DPV) of methylene blue (MB) signal. In this approach the extent of hybridization is evaluated on the basis of the difference between DPV signals of MB accumulated on the probe-AuE and MB accumulated on the probe-target-AuE. Some experimental variables affecting the performance of the biosensor including oxygen interference during the assay, probe immobilization time, probe concentration and MB accumulation time were investigated. The PNA probe modified AuE in its optimum condition was shown to be an effective sensor for the detection of hybridization and point mutations. The obtained detection limit of the utilized biosensor has been calculated as 22 nm.     

Synergistic effects of nano-ZnO/multi-walled carbon nanotubes/chitosan nanocomposite membrane for the sensitive detection of sequence-specific of PAT gene and PCR amplification of NOS gene

The remarkable synergistic effects of the zinc oxide (ZnO) nanoparticles and multi-walled carbon nanotubes (MWNTs) were developed for the ssDNA probe immobilization and fabrication of the electrochemical DNA biosensor. The ZnO/MWNTs/chitosan nanocomposite membrane-modified glassy carbon electrode (ZnO/MWNTs/CHIT/GCE) was fabricated and the ssDNA probes were immobilized on the modified electrode surface. The preparation method is quite simple and inexpensive. The hybridization events were monitored by differential pulse voltammetry (DPV) using methylene blue (MB) as an indicator. As compared with previous MWNTs-based DNA biosensors, this composite matrix combined the attractive biocompatibility of ZnO nanoparticles with the excellent electron-transfer ability of MWNTs and fine membrane-forming ability of CHIT increased the DNA attachment quantity and complementary DNA detection sensitivity. The approach described here can effectively discriminate complementary DNA sequence, noncomplementary sequence, single-base mismatched sequence and double-base mismatched sequence related to phosphinothricin acetyltransferase (PAT) gene in transgenic corn. Under optimal conditions, the dynamic detection range of the sensor to PAT gene complementary target sequence was from 1.0 × 10⁻¹¹ to 1.0 × 10⁻⁶ mol/L with the detection limit of 2.8 × 10⁻¹² mol/L. The polymerase chain reaction (PCR) amplification of nopaline synthase (NOS) gene from the real sample of one kind of transgenic soybeans was also satisfactorily detected with this electrochemical DNA biosensor, suggesting that the ZnO/MWNTs/CHIT nanocomposite hold great promises for sensitive electrochemical biosensor applications.     

An Electrochemical DNA Sensor Based on Electrodepositing Aluminum Ion Films on Stearic Acid‐Modified Carbon Paste Electrode and Its Application for the Detection of Specific Sequences Related to Bar Gene and CP4 Epsps Gene

An electrochemical DNA biosensor was fabricated by immobilizing DNA probe on aluminum ion films that were electrodeposited on the surface of the stearic acid‐modified carbon paste electrode (CPE). DNA immobilization and hybridization were characterized with cyclic voltammetry (CV) by using methylene blue (MB) as indicator. MB has a couple of well‐defined voltammetric redox peaks at the CPE. The currents of redox peaks of MB decreased after depositing aluminum ion films on the CPE (Al(III)/CPE) and increased dramatically after immobilizing DNA probe (ssDNA/Al(III)/CPE). Hybridization of DNA probe led to a marked decrease of the peak currents of MB, which can be used to detect the target single‐stranded DNA. The conditions for the preparation of Al(III)/CPE, and DNA immobilization and hybridization were optimized. The specific sequences related to bar transgene in the transgenic corn and the PCR amplification of CP4 epsps gene from the sample of transgenic roundup ready soybean were detected by differential pulse voltammetry (DPV) with this new electrochemical DNA biosensor. The difference between the peak currents of MB at ssDNA/Al(III)/CPE and that at hybridization DNA modified electrode (dsDNA/Al(III)/CPE) was applied to determine the specific sequence related to the target bar gene with the dynamic range comprised between 1.0×10^?7 mol/L to 1.0×10^?4 mol/L. A detection limit of 2.25×10^?8 mol/L of oligonucleotides can be estimated.     

DNA‐Directed Attachment of Carbon Nanotubes for Enhanced Label‐Free Electrochemical Detection of DNA Hybridization

Multi‐walled carbon nanotubes (MWNTs) were used as nanowires, which combined DNA molecules to a carbon paste electrode (CPE). The attachment of MWNT on the electrode surface was controlled by a hybridization assay between adenine and thymine containing oligonucleotides. The appearance of guanine oxidation signal after hybridization with target DNA greatly simplified the specific sequence DNA detection mechanism. Combination of sidewall‐ and end‐functionalization of MWNT provided a significant enhancement in the voltammetric signal of guanine oxidation in comparison with the signals obtained from only end‐oxidized MWNT modified CPE and a bare CPE. A control experiment involving adenine containing polynucleotide (poly(A)) instead of adenine probe modified MWNT was performed. The effect of target and noncomplementary DNA concentration on the guanine signal was also monitored. Discrimination against single‐base mismatch and noncomplementary DNA was achieved by surfactant containing washing solution. The promising conductivity of carbon nanotubes, and the creation of a larger surface area for DNA immobilization by sidewall‐ and end‐oxidation of MWNT provided a detection limit down to 10 pg/mL, which is compatible with the demand of the genetic tests.     

Quantum dot-based electrochemical DNA biosensor using a screen-printed graphite surface with embedded bismuth precursor

This work reports the development of screen-printed quantum dots (QDs)-based DNA biosensors utilizing graphite electrodes with embedded bismuth citrate as a bismuth precursor. The sensor surface serves both as a support for the immobilization of the oligonucleotide and as an ultrasensitive voltammetric QDs transducer relying on bismuth nanoparticles. The utility of this biosensor is demonstrated for the detection of the C634R mutation through hybridization of the biotin-tagged target oligonucleotide with a surface-confined capture complementary probe and subsequent reaction with streptavidin-conjugated PbS QDs. The electrochemical transduction step involved anodic stripping voltammetric determination of the Pb(II) released after acidic dissolution of the QDs. Simultaneously with the electrolytic accumulation of Pb on the sensor surface, the embedded bismuth citrate was converted in situ to bismuth nanoparticles enabling ultra-trace Pb determination. The biosensor showed a linear relationship of the Pb(II) peak current with respect to the logarithm of the target DNA concentrations from 0.1 pmol L^− 1 to 10 nmol L^− 1, and the limit of detection was 0.03 pmol L^− 1. The biosensor exhibited effective discrimination between a single-base mismatched sequence and the fully complementary target DNA. These “green” biosensors are inexpensive, lend themselves to easy mass production, and hold promise for ultrasensitive bioassay formats.     

A Biosensor for Genetic Modified Soybean DNA Determination via Adsorption of Anthraquinone‐2‐sulphonic Acid in Reduced Graphene Oxide

An electrochemical DNA biosensor for DNA determination of genetically modified (GM) soybean (CaMV 35S target genes) was developed utilizing a new detection concept based on the adsoption of anthraquinone‐2‐sulphonic acid (AQMS) on the reduced graphene oxide nano‐particles (rGO) during DNA hybridization events. The aminated DNA probe for CaMV 35S was immobilized onto poly(n‐butyl acrylate) film modified with succinimide functional groups [poly(nBA‐NAS)] via peptide covalent bond. Nanosheets of rGO were entrapped in the poly(nBA‐NAS) film to form a conducting [poly(nBA‐NAS)‐rGO] film of the DNA biosensor. Besides facilitating the electron transfer reactions, the rGO also functioned as an adsorbent for AQMS. The sensing mechanism of the proposed DNA biosensor involved measuring the oxidation current of the AQMS adsorbed on the electrode surface at −0.50 V using differential pulse voltammetry (DPV) before and after a DNA hybridization event. Under optimum conditions, the DNA biosensor demonstrated a linear proportionality between AQMS oxidation signal and logarithm cDNA concentration from 1.0×10⁻¹⁵ M to 1.0×10⁻⁸ M target DNA with a detection limit of 6.3×10⁻¹⁶ M. The electrochemical DNA biosensor possessed good selectivity and a shelf life of about 40 days with relative standard deviation of reproducibility obtained in the range of 3.7–4.6% (n=5). Evaluation of the DNA biosensor using GM soybean DNA extracts showed excellent recovery percentages of 97.2–104.0.     

Application of graphene oxide nanosheets as probe oligonucleotide immobilization platform for DNA sensing

In this work, a simple and novel electrochemical biosensor based on a glassy carbon electrode (GCE) modified with graphene oxide nanosheets (GO) was developed for detection of DNA sequences. The morphology of prepared nanoplatform was investigated by scanning electron microscopy, infrared (FTIR) and UV/Vis absorption spectra. The fabrication processes of electrochemical biosensor were characterized with cyclic voltammetry and electrochemical impedance spectroscopy (EIS) in an aqueous solution. The optimization of experimental conditions such as immobilization of the probe BRCA1 and its hybridization with the complementary DNA was performed. Due to unique properties of graphene oxide nanosheets such as large surface area and high conductivity, a wide liner range of 1.0 × 10^?17–1.0 × 10^?9 M and detection limit of 3.3 × 10^?18 M were obtained for detection of BRCA1 5382 mutation by EIS technique. Under the optimum conditions, the proposed biosensor (ssDNA/GO/GCE) revealed suitable selectivity for discriminating the complementary sequences from non-complementary sequences, so it can be applicable for detection of breast cancer.     

基于聚硫堇膜对DNA杂交的直接电化学检测

In this work, the application of a conducting polymer, poly（thionine）, modified electrode as matrix to DNA immobilization as well as transducer to label-free DNA hybridization detection was introduced. The electropolymerization of thionine onto electrode surface was carried out by a simple two-step method, which involved a preanodization of glassy carbon electrode at a constant positive potential in thionine solution following cyclic voltammetry scans in the solution. Electrochemical detection was performed by differential pulse voltammetry in the electroactivity potential domain of poly（thionine）. The resulting poly（thionine） modified electrode showed a good stability and electroactivity in aqueous media during a near neutral pH range. Additionally, the pendant amino groups on the poly（thionine） chains enabled poly（thionine） modified electrode to immobilize phosphate group terminated DNA probe via covalent linkage. Hybridization process induced a clear decrease in poly（thionine） redox current, which was corresponding to the decrease in poly（thionine） electroactivity after double stranded DNA was formed on the polymer film. The detection limit of this electrochemical DNA hybridization sensor was 1.0 × 10^-10mol/L. Compared with complementary sequence, the hybridization signal values of 1-base mismatched and 3-base mismatched samples were 63.9% and 9.2%, respectively.