海藻酸钙凝胶包埋乳酸氧化酶催化DL-乳酸生产丙酮酸

研究了用海藻酸钠包埋、戊二醛交联法固定耻垢分枝杆菌(Mycobacterium Srnegmatis)生成乳酸氧化酶的最佳条件,比较了原酶与固定化酶的酶学性质.将1mL酶液和1 mL质量分数为3%的海藻酸钠溶液的混合液,用注射器滴加到20 mL0.2 mol/L.的CaCl2溶液中,25℃静置固化2 h后,过滤洗涤,将同体转移至20 mL质量分数为0.2%戊二醛溶液中37℃交联2 h后,过滤、洗涤和干燥得到球状同定化酶.固定化酶的活力回收率为39.8%.酶学性质研究表明,此固定化酶的热稳定性较好,游离酶在65 ℃保温l h酶蛋白完全变性失活,而固定化酶在65℃保温1 h仍可保持86%的酶活力;其最适酶促反应温度可由37℃升至55℃,最适反应pH=7.4保持不变;在不加保护剂的条件下,4℃放置50 d后游离酶仅保持40%以上的酶活力,而固定化酶能保持80%以上的酶活力.该固定化乳酸氧化酶用于催化氧化DL-乳酸生产丙酮酸,3 h后丙酮酸产率可达75%,连续循环使用5次固定化酶活力仍保持85%.     

固定化扩展青霉脂肪酶的制备及其在玉米油转酯反应中的应用

采用吸附法对来源于扩展青霉Penicillium expansum的脂肪酶进行了固定化.从20种不同来源的树脂中筛选出固定化效率高且价格低廉的D4020树脂作为载体,系统研究了固定化条件对固定化效率及固定化酶转酯活力的影响.结果表明,最适加酶量、缓冲液pH和吸附时间分别为0.7 g/g、9.4和4 h.冻干时添加0.5%的半乳糖有助于提高固定化酶的转酯活力.在上述优化条件下,固定化酶的转酯活力为404.0 U/g,而所用的游离酶不能催化该转酯反应.利用该固定化酶催化玉米油转酯反应生产生物柴油时,叔戊醇为适宜的反应介质,其最适添加量为0.5 ml/g;适宜的酶量、加水量和反应温度分别为60.6 U/g、油重的1.2%和35℃.按醇/油摩尔比为1的比例分别在反应0、2和6 h时加入甲醇,在优化反应条件下,反应24 h后甲酯产率达85.0%;固定化脂肪酶具有较好的操作稳定性,反应10批次时,相对酶活力为62.8%.     

黑曲霉脂肪酶的耦合固定化及特性

研究了吸附-絮凝耦合的方法固定脂肪酶的工艺条件.结果表明:在33℃下,用0.03mol/L的磷酸二氢钾?氢氧化钠缓冲液控制体系pH为7.0,酶与树脂(质量比1∶8)作用吸附1h后,用0.2mL絮凝剂聚丙烯酰胺(w(PAM)=0.5%)处理,得到活力较高的固定化脂肪酶.固定化酶最适pH9.0,最适温度为45℃,活力为405U/g,酶活回收率可以达到40%.固定化脂肪酶制备简便,可重复使用,稳定性较高.     

固定化木瓜蛋白酶的制备和性质研究

多孔硅球固定化木瓜蛋白酶具有热增活性 .本文在前文研究的基础上 ,用载体交联法制备了甲壳胺固定化木瓜蛋白酶和纤维素固定化木瓜蛋白酶 .考察了固定化pH值、戊二醛浓度和给酶量对固定化木瓜蛋白酶活力的影响 .研究了固定化木瓜蛋白酶的性质 ,特别是热稳定性和耐热性 ,并与溶液酶和多孔硅球固定化木瓜蛋白酶进行了比较 .所制得的甲壳胺固定化木瓜蛋白酶和纤维素固定化木瓜蛋白酶的最适反应温度均达到了 80℃ ;90℃温育 1h后固定化酶的活力保持在 95 %以上 ;70℃温育处理 5h和 6h后固定化酶的活力也仍能保持在 90 %以上 .固定化木瓜蛋白酶的热稳定性和耐热性得到了显著提高     

壳聚糖固定化乳酸脱氢酶的制备及酶学性质研究

以磁性壳聚糖作为载体,戊二醛作为交联剂,对乳酸脱氢酶(LDH)进行固定化.固定化的最适条件为:戊二醛浓度6%,pH值7.5,酶的偶联时间2 h.对游离及固定化LDH酶学性质的研究表明,酶促反应的最适pH值为9.2,最适温度分别为37℃和50℃,对乳酸的表观米氏常数分别为1.6 mmol/L和0.9 mmol/L.游离酶和固定化酶在40℃放置150 min后,其活力分别为最初的56.5%和76.1%.固定化酶在4℃贮存4周后,活力仍保留50%以上.固定化酶在室温下与底物重复反应6次后,活力仍保留60%以上,说明固定化酶具有较好的热稳定性、贮存稳定性和复用性.     

纳米-微米复合孔泡沫陶瓷固定化脂肪酶

考察了泡沫陶瓷的孔径分布和表面性质对脂肪酶固定化的影响.研究表明,泡沫陶瓷的纳米孔孔径分布非常适合脂肪酶的固定化,对固定化酶的催化效率有决定性的影响.经1h的定化,泡沫陶瓷固定化酶的活性达商业化硅藻土固定化酶的1.33倍,体积活力为其2.63倍,蛋白载量为45.36mg/g陶瓷,比活为1215.39U/g,活力回收为41.2%.泡沫陶瓷固定化脂肪酶在有机相乙酸乙酯合成中表现优良,连续使用5次,每次反应3h,乙酸转化率均在93%左右.     

阳离子交换树脂吸附交联固定鸡肝酯酶的实验研究

研究了基于酶抑制原理的农药残留生物传感器中固定化酶的制备方法.以离子交换树脂作为固定化载体,戊二醛为交联剂,采用吸附交联相结合的方法制备了固定化鸡肝酯酶.在 10℃下吸附75min,以及酶活力浓度固定在6U/ml±2U/ml,在交联过程中戊二醛浓度0.04%,10℃下交联1h的条件下可以获得最佳的固定效果.并且,用吸附交联制得的固定化酶相对于用吸附法制得固定化酶用于流动分析过程,其热稳定性和耐冲刷性更好.同时,在保存阶段也具有更好的稳定性.     

磁性纳米氮化铝颗粒固定化β-葡萄糖苷酶的性质

以戊二醛为交联剂,研究了磁性纳米氮化铝颗粒固定化β-葡萄糖苷酶的条件及固定化酶的结构特征,并考察了固定化酶的某些酶学性质.结果表明,在4.5 ml磁性纳米氮化铝颗粒悬液(100 mg/ml)中加入0.5 ml戊二醛溶液(2%)超声波分散后,加入5 ml β-葡萄糖苷酶溶液(50 mg/ml),于20℃,pH 5.0和100 r/min条件下固载3.5 h,酶蛋白和酶活回收率分别为82.6%和78.4%.固定化β-葡萄糖苷酶的结构松散,不改变酶的结构特征.与游离酶相比,固定化酶对对硝基苯基-β-D-葡萄糖苷水解反应的最佳反应温度有所降低,最佳反应pH值有所升高,而米氏常数Km值有所增大,且具有良好的贮存稳定性和操作稳定性,表明磁性纳米氮化铝颗粒适合作为β-葡萄糖苷酶的固定化载体.     

复合纤维素膜固定化胰蛋白酶反应器及其应用于蛋白质酶解

合成了甲基丙烯酸缩水甘油酯-纤维素复合膜,并以此膜为基质共价键合固定化胰蛋白酶,以N-苯甲酰-L-精氨酰乙酯(BAEE)为底物,应用高效液相色谱系统测定了酶固定化膜柱的催化反应特性。研究结果表明:温度、pH值、离子强度、有机溶剂及蛋白变性剂等都对固定化酶的活力有一定的影响。在最适条件下,固定化胰蛋白酶的活力为17800U/g干膜,蛋白载量为3.6mg/g(≈0.15μmol/g)干膜,活性回收率达到52%.固定化酶表现出较高的使用和储藏稳定性,在40℃下,水解BAEE底物24h活力无显着变化。固定化酶膜柱在4℃冷藏保存100d仍保存90%以上的水解活力。固定化酶反应器被应用于蛋白质酶解的肽谱实验。     

界面活化的溶胶凝胶包埋Candida rugosa脂肪酶催化合成维生素E琥珀酸酯

采用界面活化的溶胶凝胶包埋Candida rugosa脂肪酶(CRL)催化合成了维生素E琥珀酸酯.考察了影响溶胶凝胶包埋固定化CRL的因素,获得的最佳固定化条件为:丙基三甲氧基硅烷/正硅酸四乙酯摩尔比为1/1,水与硅烷前体摩尔比为15,酶的添加量为0.5mg/ml,PEG400的添加量为12μl/ml溶胶. 溶胶凝胶包埋的CRL在50℃,18h后其活性仍然保持了70.58%,是游离酶的2.6倍,且稳定性得到了明显的改善.基于CRL的界面特性,采用五种表面活性剂对其进行界面活化.结果表明,采用橄榄油活化的溶胶凝胶包埋的CRL合成维生素E琥珀酸酯的酯化活力最高,相比原酶和未界面活化的溶胶凝胶包埋酶分别提高了6.7和1.43倍.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

正丁胺对激光染料荧光谱影响的研究

用正丁胺作为碳源,采用射频辉光放电制备碳膜,选用激光染料R6G和聚乙二醇混合液作为蒸气源,采用单源热蒸发,在蒸发室与染料同时沉积得到混合膜,用拉曼光谱和红外光谱分析了碳膜的结构和键合方式,分析表明:碳膜中存在胺基团和氢原子.混合膜的荧光谱测量结果表明,认为正丁胺对染料荧光谱的影响是因为胺基和氢原子的存在.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.