Evaluation of a platinum electrode modified with hydroxyapatite in the lead(II) determination in a square wave voltammetric procedure

The behavior of a modified carbon platinum electrode (Pt) for lead(II) determination by square wave voltammetry (SWV) was studied. The modified electrode is obtained by electrodeposition of hydroxyapatite (HAP) on the surface of a bare platinum electrode. The new electrode (HAP/Pt) revealed interesting electroanalytical detection of lead(II) based on the adsorption of this metal onto hydroxyapatite under open circuit conditions. After optimization of the experimental and voltammetric conditions, the best voltammetric responses-current intensity and voltammetric profile were obtained in 0.2 mol L^?1 KNO₃ with: 30 min accumulation time, 5 mV pulse amplitude and 1 mV s^?1 scan rate. The observed detection (DL, 3σ) and quantification (DL, 10σ) limits in pure water were 2.01 × 10^?8 and 6.7 × 10^?7 mol L^?1, respectively. The reproducibility of the proposed method was determined from five different measurements in a solution containing 2.2 × 10^?6 mol L^?1 lead(II) with a coefficients of variation of 2.08%.The electrochemical of hydroxyapatite at platinum surfaces was characterized, after calcinations 900 °C, by X-ray diffraction, infrared spectroscopy, chemical and electrochemical analysis.     

Determination of secnidazole in tablets and human serum by cathodic adsorptive stripping voltammetry

The electrochemical reduction of secnidazole was carried out in BR buffer solutions in the pH range 2.0–11.8 by dc polarography. The polarograms exhibited two irreversible reduction waves in acidic media and one wave in alkaline media, corresponding to the reduction of nitro group in the drug. The cathodic adsorptive voltammetric behavior was studied on glassy carbon electrode to optimize an analytical method for determination of secnidazole. The drug was determined in the range between 4.0 × 10^?6 and 1.2 × 10^?4 mol L^?1. The proposed method was successfully applied to the determination of the drug content in tablets with mean recovery and relative standard deviation of 100.91% and 1.82%, respectively. It was also applied to human serum with a good precision and accuracy.     

Electrochemical determination of rosiglitazone by square-wave adsorptive stripping voltammetry method

Square-wave adsorptive stripping voltammetry technique was used to determine rosiglitazone (ROS) on the hanging mercury dropping electrode (HMDE) surface, in Britton Robinson buffer, pH = 5. The voltammetric cathodic peak was observed at ?1520 mV vs. Ag/AgCl reference electrode. The voltammetric peak response was characterized with respect to pH, supporting electrolyte, accumulation potential, preconcentration time, scan rate, frequency, pulse amplitude, surface area of the working electrode and the convection rate. Under optimal conditions, the voltammetric current is proportional to the concentration of ROS over the concentration range of 5 × 10^?8–8 × 10^?7 mol l^?1 (r = 0.9899) with a detection limit of 3.2 × 10^?11 mol l^?1 using 120 s accumulation time. The developed SW-AdSV procedure showed a good reproducibility, the relative standard deviation RSD% (n = 10) at a concentration level of 5 × 10^?7 mol l^?1 was 0.33%, whereas the accuracy was 101% ± 1.0. The proposed method was successfully applied to assay the drug in the human urine and plasma samples with mean recoveries of 90 ± 0.71% and 86 ± 1.0%, respectively.     

Anodic electrochemiluminescent behavior of lucigenin on MWNT/GCE

The electrochemiluminescent (ECL) behavior of lucigenin on a multiwall carbon nanotubes modified glassy carbon electrode (MWNT/GCE) during anodic scanning was studied. A strong and stable anodic ECL signal was found on MWNT modified electrode, which results from the oxidation reaction between lucigenin and the oxidation production of OH^-. The effects of electrode materials, pH and scan rate on the ECL intensity were studied, and the possible ECL mechanism was also proposed. Under the optimized conditions, the ECL intensity was found to be linear with concentration of lucigenin in the range of 5.0 × 10^?7–5.0 × 10^?6 mol/L with a detection limit of 2.0 × 10^?7 mol/L. Superoxide dimutase (SOD) was found to be able to inhibit this ECL system, based on which a sensitive ECL methods for detection of SOD had been established.     

Determination of nitrite with the electrocatalytic property to the oxidation of nitrite on thionine modified aligned carbon nanotubes

A thionine modified aligned carbon nanotubes (ACNTs) electrode was fabricated and was used to electrochemically determine nitrite. The thionine modified ACNTs electrode exhibited enhanced electrocatalytic behavior to the oxidation of nitrite. The electrochemical mechanism of the thionine/ACNTs electrode towards the oxidation of nitrite was discussed. The thionine modified ACNTs electrode exhibited fast response towards nitrite with a detection limit of 1.12 × 10⁻⁶ mol  L⁻¹ and a linear range of 3 × 10⁻⁶ – 5 × 10⁻⁴ mol  L⁻¹. The proposed method was successfully applied in the detection of nitrite in real samples.     

An enhanced electrocatalytic oxidation and determination of 2,4-dichlorophenol on multilayer deposited functionalized multi-walled carbon nanotube/Nafion composite film electrode

The voltammetric (CV and DPV) behavior of multi-walled carbon nanotube/Nafion composite coupled with a glassy carbon electrode was investigated for the determination of 2,4-dichlorophenol. The structural and morphological evaluation by XRD and FESEM revealed that the acid treated MWCNT retained their morphology without any structural change. The existence of the possible functional groups was investigated by FTIR and Raman spectroscopy. Compared to bare GCE, a significantly reduced interfacial charge transfer resistance was noticed for MWCNT/Nafion/GCE by electrochemical impedance spectroscopy (EIS). The use of Nafion not only contributed to the non-covalent functionalization of MWCNT, but also protected the electrode surface against the polymerization of phenoxy radicals forming a passivating film. For MWCNT/Nafion/GCE, the combination of anti-passivating ability and excellent catalytic properties resulted in the rapid and direct electrochemical determination of 2,4-DCP. Under optimal experimental conditions, the DPV responses for MWCNT/Nafion/GCE is linear over the 1–150 μmol/L range with a detection limit (S/N = 3) of 0.01 μmol/L. The presence of many interfering species had no influence on the signals of 2,4-DCP. The proposed sensor was successfully tested for the determination of 2,4-DCP in tap water samples and the recovery was in the range of 99.0–102.5%.     

High performance electrochemical sensor based on modified screen-printed electrodes with cost-effective dispersion of nanostructured carbon black

A novel sensor based on a screen-printed electrode (SPE) modified with a stable dispersion of commercially available carbon black (CB) N220 was developed. This probe showed significantly enhanced electrochemical activity relative to a bare SPE when tested with ferricyanide, epinephrine, norepinephrine, benzoquinone and NADH. When challenged in amperometric batch mode with NADH, the response was stable and revealed a linear dependence up to 2·10^?4 mol L^?1 with a detection limit of 3·10^?7 mol L^?1. The analytical performance, coupled with the low cost of the CB nanomaterial, suggests that this sensor holds promise for electrochemical applications.     

Electrocatalytic oxidation of NADH based on bicontinuous gyroidal mesoporous carbon with low overpotential

The electrochemical oxidation of β-nicotinamide adenine dinucleotide (NADH) is studied at a glassy carbon electrode (GCE) modified with bicontinuous gyroidal mesoporous carbon (BGMC). Due to the large surface area and remarkable electrocatalytic properties of BGMC, the BGMC/GCE exhibits potent electrocatalytic activity toward the electro-oxidation of NADH. A substantial decrease of 649 mV in the overpotential of NADH oxidation reaction is achieved compared with a bare GCE. The anodic peak currents increase steadily with the concentration of NADH in a broad range from 3.0 × 10^?6 to 1.4 × 10^?3 M with a low detection limit of 1.0 × 10^?6 M under the optimal condition.     

A novel sensitive biosensor for Ca2+ based on electropolymerized melatonin modified electrode

An electropolymerized melatonin modified glassy carbon electrode (EPMT/GCE) was prepared by electrochemically polymerizing of melatonin in a 0.04 mol l^?1 perchloric acid solution. In KCl solution, Ca²⁺ was found to perform a reversible complex reaction on the EPMT/GCE to produce a sharp complex adsorption wave. The configuration of the electropolymerized membrane was characterized by scanning electron microscope and various electrochemical techniques. Based on which, a novel sensitive Ca²⁺ electrochemical sensor was established. The peak current showed a linear relationship with Ca²⁺ concentration in range of 6.2 × 10^?7–1.0 × 10^?4 mol l^?1 with detection limit of 4.5 × 10^?7 mol l^?1. The developed electrochemical sensor has been used for determination of Ca²⁺ in body fluid.     

Simultaneous determination of ascorbic acid,epinephrine, and uric acid by differential pulse voltammetry using poly(p-xylenolsulfonephthalein) modified glassy carbon electrode

A novel poly(p-xylenolsulfonephthalein) modified glassy carbon electrode was prepared for the simultaneous determination of ascorbic acid (AA), epinephrine (EP) and uric acid (UA). Cyclic voltammetric, chronoamperometric, and differential pulse voltammetric methods were used to investigate the modified electrode for the electrocatalytic oxidation of EP, AA, and UA in aqueous solutions. The separation of the oxidation peak potentials for AA–EP and EP–UA was about 200 and 130 mV, respectively. The calibration curves obtained for AA, EP, and UA were in the ranges of 10–1343, 2–390, and 0.1–560 μmol L⁻¹, respectively. The detection limits (S/N = 3) were 4, 0.1, and 0.08 μmol L⁻¹ for AA, EP and UA, respectively. The diffusion coefficient and the catalytic rate constant for the oxidation of EP at the modified electrode were calculated as 1.40(±0.10) × 10⁻⁴ cm² s⁻¹ and 1.06 × 10³ mol⁻¹ L s⁻¹, respectively. The present method was applied to the determination of EP in pharmaceutical and urine samples, AA in commercially available vitamin C tablet, and EP plus UA in urine samples.     

Determination of zinc by square-wave adsorptive stripping voltammetry using alizarin as a chelating agent

The adsorptive collection of zinc(II) complex with alizarin ligand, coupled with the square-wave voltammetric technique at the hanging mercury drop electrode, yields a very sensitive electroanalytical procedure for the determination of zinc. The optimized experimental conditions include: supporting electrolyte (carbonate buffer), pH (11), alizarin concentration (1 × 10^?6 mol l^?1), accumulation time (60 s), accumulation potential (?0.1 V), scan rate (700 mV s^?1), pulse amplitude (0.06 V) and SW frequency (80 Hz). The monitored stripping voltammetric current was linear over the range of 5 × 10^?8 – 4 × 10^?7 mol l^?1 and the detection limit was 1 × 10^?8 mol l^?1. The relative standard deviation was calculated as 1.3% (n = 10) for 1 × 10^?8 mol l^?1 Zn(II) and the obtained electrochemical signal was stabile for up to 60 min. Possible interferences by either co-existing metal ions or other chelating agents were also investigated. The applicability of the proposed SW-AdSV method to the analysis of foodstuff was assessed by the determination of zinc content in instant coffee samples. The accuracy of the obtained voltammetric analytical results was validated by comparing with that obtained by atomic absorption spectrometric method and conducting the necessary statistical evaluation.     

Poly-xanthurenic acid as an efficient mediator for the electrocatalytic oxidation of NADH

This paper describes, for the first time, the development of a simple and highly sensitive chemical sensor based on a new electroactive material, electrogenerated in situ from xanthurenic acid on an electrode modified with MWCNT. The modified electrode shows efficient electrocatalytic oxidation activity towards NADH at an applied potential of 0.1 V vs. Ag/AgCl. The kinetic constant, k_kin, for the electrocatalytic oxidation of NADH, evaluated by chronoamperometry and voltammetry using RDE, provided values close to 10⁵ mol^?1 L s^?1.     

A study of adsorptive stripping voltammetric behavior of ofloxacine antibiotic in the presence of Fe(III) and its determination in tablets and biological fluids

Square-wave voltammetry was used to explore the adsorption property of ofloxacine complex with iron ion on the hanging mercury drop electrode (HMDE). By employing the adsorptive stripping voltammetric approach, a sensitive electroanalytical method for the quantitative analysis of ofloxacine antibiotic was achieved. A well-developed voltammetric peak was obtained in pH 7.5 Britton–Robinson buffer (B–R buffer) at ?1400 mV. The cyclic voltammetric studies indicated that the reduction process was irreversible and primarily controlled by adsorption. An investigations of the variation of adsorptive voltammetric peak current with supporting electrolyte, pH, accumulation time, accumulation potential, ion concentration, scan rate, pulse amplitude, SW frequency, working electrode area and convection rate has resulted in the recognition of optimal experimental conditions for ofloxacine analysis. The studied electroanalytical signal showed a linear response for ofloxacine in the concentration range 5 × 10^?7 to 1.7 × 10^?6 mol l^?1 (r = 0.999). A limit of detection of 1.1 × 10^?8 mol l^?1 (3.98 ppb) with relative standard deviation of 1.21 RSD% and mean recovery of 99.6% were obtained. Possible interferences by several substances usually present in pharmaceutical formulation were also evaluated. The analytical quantification of ofloxacine in commercially available pharmaceutical formulation was performed and compared with data from HPLC technique.     

Fluorescence “turn-on” chemosensor for the selective detection of zinc ion based on Schiff-base derivative

N,N′-phenylenebis(salicylideaminato) (L) has been used to detect trace amounts of zinc ion in acetonitrile–water solution by fluorescence spectroscopy. The fluorescent probe undergoes fluorescent emission intensity enhancement upon binding to zinc ions in MeCN/H₂O (1:1, v/v) solution. The fluorescence enhancement of L is attributed to the 1:1 complex formation between L and Zn(II), which has been utilized as the basis for selective detection of Zn(II). The linear response range for Zn(II) covers a concentration range of 1.6 × 10^?7 to 1.0 × 10^?5 mol/L, and the detection limit is 1.5 × 10^?7 mol/L. The fluorescent probe exhibits high selectivity over other common metal ions, and the proposed fluorescent sensor was applied to determine zinc in water samples and waste water.     

Microwave-radiated synthesis of gold nanoparticles/carbon nanotubes composites and its application to voltammetric detection of trace mercury(II)

Gold nanoparticles/carbon nanotubes (Au-NPs/CNTs) composites were rapidly synthesized by microwave radiation, and firstly applied for the determination of trace mercury(II) by anodic stripping voltammetry (ASV). The structure and composition of the synthesized Au-NPs/CNTs nanocomposites were characterized by transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDX), UV–vis absorption spectroscopy and cyclic voltammetry. Au-NPs/CNTs nanocomposites modified glassy carbon electrode (Au-NPs/CNTs/GCE) exhibited excellent performance for Hg(II) analysis. A wide linear range (5 × 10⁻¹⁰–1.25 × 10⁻⁶ mol/L) and good repeatability (relative standard deviation of 1.84%) were obtained for Hg(II) detection. The limit of detection was found to be 3 × 10⁻¹⁰ mol/L (0.06 μg/L) at 2 min accumulation, while the World Health Organization’s guideline value of mercury for drinking water is 1 μg/L, suggesting the proposed method may have practical utility.     

A dysprosium nanowire modified carbon paste electrode for determination of levodopa using fast Fourier transformation square-wave voltammetry method

A new detection technique called the fast Fourier transform square-wave voltammetry (FFT-SWV) is based on the measurements of electrode admittance as a function of potential. The response of the detector (microelectrode) is fast, which makes the method suitable for most applications involving flowing electrolytes. The carbon paste electrode was modified by nanostructures to improve better sensitivity. The response is generated by a redox processes. The redox property of L-dopa was used for determination of it in human serum and urine samples. The support electrolyte that provided a more defined and intense peak current for L-dopa determination was at 0.05 mol l^?1 acetate buffer pH 7.0. Synthesized dysprosium nanowires make more effective surface like nanotubes [1], [2], [3], [4] so they are good candidates for using as a modifier for electrochemical reactions. The drug presented one irreversible oxidation peaks at 360 mV versus Ag/AgCl by modified nanowire carbon paste electrode which produced high current and reduced the oxidation potential about 80 mV.Furthermore, signal-to-noise ratio has significantly increased by application of discrete fast Fourier transform (FFT) method, background subtraction and two-dimensional integration of the electrode response over a selected potential range and time window. To obtain the much sensitivity the effective parameters such as frequency, amplitude and pH was optimized. As a result, C_DL of 4.0 × 10^?9 M and an LOQ of 7.0 × 10^?9 M were found for determination for L-dopa. A good recovery was obtained for assay spiked urine samples and a good quantification of L-dopa was achieved in a commercial formulation.     

Zinc(II) selective poly(vinyl chloride) membrane ISE using a macrocyclic compound 1,12,14-triaza-5,8-dioxo-3(4),9(10)-dibenzoylcyclopentadeca-1,12,14-triene as neutral carrier

The potentiometric response characteristics of zinc ion selective PVC-based membrane electrode employing 1,12,14-triaza-5,8-dioxo-3(4),9(10)-dibenzoyl-1,12,14-triene as an inophore was investigated. The proposed electrode exhibits a Nernstian behavior with a slope of 29.2 ± 0.4 mV per decade with a working concentration range of 1.3 × 10^?7–1.0 × 10^?1 mol L^?1 and a detection limit of 1.0 × 10^?8 mol L^?1. The membrane having the composition as TDODBCPT:O-NPOE:PVC:OA; 7:57:30:6 wt.% exhibits the best results. It has a fast response time of 7 s and can be used for at least 100 days without any considerable divergence in potential. The proposed electrode show good discrimination of Zn²⁺ ion from diverse ions. The potential response remains constant over a pH range of 3.5–9.2. The electrode found well work under laboratory conditions. The proposed sensor directly used for determination of zinc ions in human hair sample, wastewater and an indicator electrode with EDTA titration.     

Selective determination of uric acid with DNA doped polymers modified carbon fiber microelectrode

New biocomposite materials, based on the incorporation of DNA doped p-aminobenzensulfonic acid, was fabricated by electrochemical method. A carbon fiber microelectrode modified by this thin film was fabricated for selective determination of uric acid (UA) in the presence of a larger amount of ascorbic acid (AA). It was found that the voltammetric oxidation peak separation between UA and AA is about 260 mV at the modified electrode. A linear response of the peak current versus the concentration was found in the range of 8 × 10⁻⁷–6 × 10⁻⁴ M with correlation coefficient of 0.9991 and the detection limit was 5 × 10⁻⁷ M (s/n = 3) at the 5 × 10⁻⁴ M AA. The presence of high concentration AA did not interference the determination. The electropolymerized film was characterized by SEM techniques. The modified electrode shows good sensitivity, selectivity and stability.     

Amperometric sensing of dopamine using a single-walled carbon nanotube covalently attached to a conical glass micropore electrode

A single-walled carbon nanotube (SWNT) is covalently attached to the interior surface of a conical glass micropore electrode (GME) to create a novel amperometric dopamine sensor (SWNT/NH-GME). The SWNT/NH-GME combines the advantages of excellent transport properties of the cone-shaped micropore with the characteristics of a SWNT, exhibiting a dramatic electrocatalytic effect on the oxidation of dopamine (DA). Cyclic voltammetry and amperometric methods were employed to study the electrochemical behavior of the SWNT/NH-GME. The results showed that the SWNT/NH-GME sensor exhibited an excellent immunity from ascorbic acid interference and was able to measure DA concentrations with a detection limit of 4.2 × 10^?7 mol/L (S/N = 3).     

Electrochemiluminescent biosensor based on multi-wall carbon nanotube/nano-Au modified electrode

The electrochemiluminescent (ECL) behavior of lucigenin on a multi-wall carbon nanotube/nano-Au modified glassy carbon electrode (MWNT/nano-Au/GCE) was studied in this paper. Compared with the bare GCE, the ECL intensity of lucigenin can be greatly enhanced at MWNT/nano-Au/GCE. Based on the fact that superoxide dimutase (SOD) could obviously inhibit the ECL of lucigenin at MWNT/nano-Au/GCE, a sensitive ECL biosensor for determination of SOD was developed with a wide linear range of 5.0 × 10⁻⁸–5.0 × 10⁻⁶ mol/L with detection limit of 2.5 × 10⁻⁸ mol/L.