Synthesis and electropolymerization of 1,2-bis(thiophen-3-ylmethoxy)benzene and its electrochromic properties and electrochromic device application

A new thiophene-based monomer; 1,2-bis(thiophen-3-ylmethoxy)benzene (BTMB) has been synthesized and chemical structure of the monomer was characterized. Polymerization of BTMB and characterization of the resulting polymer P(BTMB) were performed. Spectroelectrochemical analysis of the P(BTMB) reflected electronic transitions at 400 nm, 520 nm and ～720 nm, corresponding to π–π* transition, polaron and bipolaron band formation respectively. Switching ability was evaluated by a kinetic study via measuring the transmittance (%T) at the maximum contrast. Dual type all polymer electrochromic device (ECD) based on P(BTMB) and poly(ethylene dioxythiophene) (PEDOT) was constructed. Spectroelectrochemistry and switching ability of the devices were investigated by UV–vis spectroscopy.     

Colouration efficiency measurements in electrochromic polymers: The importance of charge density

A poly(3,4-ethylenedioxythiopene) (PEDOT)/polyaniline (PANI) electrochromic device (ECD) was fabricated for the purpose of examining colouration efficiency (CE) as a function of charge density ingress/egress. CE is typically measured in cm²/C with the aim being to produce as large an optical density change as possible with the least amount of charge being consumed. Results indicate that CE is not constant but is highly dependent on charge density insertion and the switching voltage. At a switching voltage of 1.9 V the maximum CE_max was 1186 cm²/C, recorded at 60% of the full optical switch where as the CE_95% was 302 cm²/C at 95% of the full optical switch. Furthermore, CE_max varied depending on the switching voltage from a high of 2212 cm²/C at a switching voltage of 1.2 V, 1528 cm²/C at 1.6 V and down to 1186 cm²/C at 1.9 V. The results highlight the fact that the current practice of quoting CE as a single-valued number may not reveal enough detail about the performance of ECDs and polymers.     

Ionogels encompassing ionic liquid with liquid like performance preferable for fast solid state electrochromic devices

Novel ionogels encompassing an ionic liquid encaged in an inorganic matrix were synthesized by sol–gel chemistry. The ability of these highly conducting ionogels (∼10⁻² S cm⁻¹ at 25 °C) to act as liquid electrolytes in spite of their solid form has been exploited in inorganic electrochromic devices based on tungsten oxide and Prussian blue electrodes. These devices exhibit extremely fast switching kinetics and make it the best and only candidate for the realization of fast all solid state electrochromic devices.     

Solid state electrochromic device applications of N-(2-(thiophen-3-yl)methylcarbonyloxyethyl) maleimide

Homopolymer and copolymer of N-(2-(thiophen-3-yl)methylcarbonyloxyethyl) maleimide (NMThi) with thiophene [P(NMThi-co-Th)] were synthesized electrochemically in acetonitrile/borontrifluoride ethylether solvent mixture (1:1, v/v). Spectroelectrochemical analysis of the resulting copolymer reflected electronic transitions at 488 and 718 nm revealing π to π¹ transition and polaron formation, respectively. Switching ability was evaluated by a kinetic study via measuring the transmittance (%T) at the maximum contrast. Dual-type polymer electrochromic devices (ECDs) based on homopolymer (P(NMThi) and copolymer P(NMThi-co-Th) were constructed with poly(3,4-ethylenedioxythiophene) (PEDOT). Spectroelectrochemistry and switching ability of the devices were investigated by UV–vis spectroscopy and cyclic voltammetry.     

High contrast ratio and fast switching polymeric electrochromic films based on water-dispersible polyaniline-poly(4-styrenesulfonate) nanoparticles

We prepared polyaniline-poly(4-styrenesulfonate) nanoparticles (PANI/PSS-NPs) by chemical oxidation polymerization in aqueous solution. We investigated the potential of the PANI/PSS-NPs to be used as an anode electrode for electrochromic devices and the effect of Li⁺ insertion (or deinsertion) kinetics and diffusion of Li⁺. A uniform electrochromic layer of PANI/PSS-NPs with a size of ca. 28 nm could be obtained by a solution process, specifically spin coating. The PANI/PSS-NPs film has a high Li⁺ diffusion coefficient (～7.7 × 10^?9 cm² s^?1) and low charge transfer resistance (～99 Ω), which result in its having a fast electrochromic response time (coloring time <1.7 s, bleaching time <2.4 s), and high coloration efficiency (>108 cm² C^?1).     

Three colour electrochromic metallopolymer based on a ruthenium phenolate complex bound to poly(4-vinyl)pyridine

The photonic and electrochemical properties of a novel Ru–phenolate based metallopolymer are reported. The complex undergoes a ruthenium based reversible oxidation at approximately +0.400 V and irreversible box ligand oxidation at +0.800 V vs. Ag/AgCl. Oxidation of thin films in aqueous electrolyte at +0.500 V reversibly switches the colour from wine red to light green and a red orange colour is observed for mixed redox composition. In contrast, oxidation at potentials more positive than +1.500 V shows no visible colour change but produces a change in the near infra-red region. To determine the electrochromic switching rate and to identify the rate determining step of the, scan rate dependent cyclic voltammetry was performed under semi-infinite linear diffusion conditions in aqueous lithium perchlorate. These data reveal that the homogeneous charge transport diffusion coefficient, D_CT, is 3.6 ± 0.2 × 10⁻¹³ cm² s⁻¹, i.e., under these conditions it takes approximately 90 s to fully oxidise a 100 nm thick film.     

Enhanced electrochromic properties of hybrid P3HT/WO3 composites with multiple colorations

We investigated the enhanced electrochemical and electrochromic properties of P3HT (poly 3-hexylthiophene)/WO₃ composites. Nanoporous WO₃ layers were prepared using electrochemical anodization. P3HT was spin coated on these layers to obtain hybrid P3HT/WO₃ composites. After annealing at 300 °C for 1 h, the monoclinic phase of the WO₃ layer and self-organized lamella structure of P3HT were examined. The P3HT/WO₃ composites exhibited enhanced current densities and three different reflective colors with a combination of pristine P3HT and WO₃ during the redox reaction. Furthermore, the composites exhibited faster switching speeds compared with WO₃ layers, which might be attributed to the easy Li⁺ insertion/extraction resulting from the incorporation of P3HT.     

Dielectric spectroscopy of biodegradable poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) films

In this paper, we report a systematic study of the dielectric relaxation spectroscopy of biodegradable poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBHHx) polyester which has potential applications as a “green” dielectric material in electronic devices. The dielectric spectra was measured over a wide frequency range (10⁰ ～ 10⁷ Hz) from ?100 to 60 °C. A glass and a sub-glass transition relaxations were observed in the dielectric spectra of PHBHHx. In addition, a nearly constant loss behavior was found by analyzing the dielectric and conductivity spectra.     

Optical,structural and electrochromic studies of molybdenum oxide thin films with nanorod structure

The MoO₃ thin films were prepared via sol–gel dip coating method on glass and FTO glass substrate. The optical and other properties of multilayered MoO₃ films with 2–10 layers were investigated. The MoO₃ films were studied using UV–Visible transmission, XRD, SEM, FTIR and Cyclic Voltammetry (CV) measurements. The band gap value for MoO₃ films was evaluated and in the range of 3.2 eV–3.72 eV. The XRD spectrum reveals that the crystallinity increases along the (020) and (040) planes with the increase in thickness. The SEM images showed the formation of nanorods upto six layers. The FTIR spectrum confirms the formation of MoO₃. The 6 layered films show the maximum anodic (spike)/cathodic (peak) diffusion coefficient of 18.84/1.701 × 10^?11 cm²/s. The same film exhibits the change in optical transmission of 49% with the bleached/coloured state transmission of 62/13%.     

In situ study of electrochromic properties of self-assembled TiO2 nanotubes

Electrochromical properties of anodic self-assembled nanotubes were investigated. It was found that amorphous titania nanotubes were able to insert H⁺ ions in a highly reversible manner. Coloration of the TiO₂ nanotubes occurred at potentials below ?0.5 V vs. Ag/AgCl in 1M (NH₄)₂SO₄ aqueous solution. The proton insertion reaction probably leads to the formation of a Ti³⁺/Ti⁴⁺ solid solution in the amorphous titania electrode, as was shown by the analysis of the derivative curve. The nanotubular titania electrode shows reasonable color efficiency when compared with other electrochromic materials and it is a promising candidate for the fabrication of low-cost interdigitated electrochromic devices.     

Synthesis and electropolymerization of 5,12-dihydrothieno[3′,4′:2,3][1,4]dioxocino[6,7-b]quinoxaline and its electrochromic properties

Synthesis of a new thiophene-based monomer; 5,12-dihydrothieno[3′,4′:2,3][1,4]dioxocino[6,7-b]quinoxaline (DDQ), was realized. The chemical structure of the monomer was characterized by ¹H NMR, FTIR and mass spectroscopy techniques. Electrochemical polymerization of DDQ and characterization of the resulting polymer [P(DDQ)] was performed. Moreover, the spectroelectrochemical and electrochromic properties of the polymer film were investigated. P(DDQ) has a low oxidation potential (0.9 V) and low band gap (1.73 eV) compared to polythiophene. In addition, dual-type polymer electrochromic device (ECD) based on P(DDQ) with poly(3,4-ethylenedioxythiophene) (PEDOT) was constructed. Spectroelectrochemistry, electrochromic switching, stability and open-circuit stability of the device were studied. It was observed that polymer have good switching time, reasonable contrast and optical memory.     

Stable free-standing aramid resin film containing vanadium pentoxide and new colour electrochromism of the film by electrodeposition of gold

Vanadium pentoxide (V₂O₅) was electrodeposited on a poly(p-phenylene terephtalamide) (PPTA)-film coated electrode. The cyclic voltammogram of the film had a reversible redox current peak. The film was dark green in the reduced state and yellow in the oxidized state. To obtain new colour, gold was further electrodeposited on the film. Not only the redox current peak but also a new redox current shoulder appeared in the cyclic voltammogram of the obtained film, and it exhibited a multicoloured electrochromism: blackish green ↔ dark green ↔ green ↔  bright red. The red colour in the oxidized state was first obtained for the V₂O₅ film. The new redox current shoulder and the colour were probably due to Au_yV₂O₅ partially formed during electrodeposition of the gold. The redox of the Au_yV₂O₅ was accompanied by egress and ingress of Li⁺ ions and the new colour change.     

Manufacture and demonstration of organic photovoltaic‐powered electrochromic displays using roll coating methods and printable electrolytes

Electrochromic devices (ECDs) were prepared on flexible substrates using spray coating and slot‐die coating methods. The electrochromic materials were the conjugated electroactive polymers, poly((2,2‐bis(2‐ethylhexyloxymethyl)‐propylene‐1,3‐dioxy)‐3,4‐thiophene‐2,5‐diyl) as a vibrantly colored active material (ECP‐Magenta) and poly(N‐octadecyl‐(propylene‐1,3‐dioxy)‐3,4‐pyrrole‐2,5‐diyl) as a minimally colored, charge balancing material (MCCP). Two electrolyte systems were compared to allow development of fully printable and laminated devices on flexible substrates. Devices of various sizes, up to 7 × 8 cm², are demonstrated with pixelated devices containing pixel sizes of 4 × 4 mm² or 13 × 13 mm². The transmission contrast exhibited by the devices, when switched between the fully bleached and fully colored state, was 58% at a visible wavelength of 550 nm, and the devices exhibited switching times of <10 s. Additionally, we demonstrate the utilization of printed organic photovoltaic devices (with or without the use of a lithium‐polymer battery) to power the devices between the colored and bleached state, illustrating a self‐powered ECD. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Aliphatic thioether polymers as novel cathode active materials for rechargeable lithium battery

Two aliphatic thioether polymers, poly[methanetetryl-tetra(thiomethylene)] (PMTTM) and poly(2,4-dithiopentanylene) (PDTP) were designed, synthesized, characterized and tested as cathode active materials. The chemical structure of polymers was confirmed by FT-IR, FT-Raman, and XPS spectral analysis. Both polymers were found to have electrochemical activity as cathode materials for rechargeable lithium battery by the electrochemical tests. The specific capacity of PMTTM was 504 mA h g⁻¹ at the third cycle and faded to 200 mA h g⁻¹ after 10 cycles; PDTP showed low and stable specific capacity around 100 mA h g⁻¹ even after 50 cycles. The specific capacity of fully saturated aliphatic thioether polymers demonstrated that thioether bonds offered energy storage. It was proposed that thioether bond was oxidized to form thioether cations with the help of ether solvents.     

Facile preparation of a visible- and near-infrared-active electrochromic film by direct deposition of a ruthenium dioxolene complex on an ITO/glass surface

An electrochromic film was prepared by simple evaporation of a solution of a ruthenium-dioxolene dye on an ITO/glass surface to give a mechanically attached layer, without the need for special anchoring groups or polymerisation to achieve surface attachment. Using an aqueous solvent/electrolyte system, in which the microcrystalline dye is insoluble, reversible electrochemical behaviour is observed leading to substantial changes in absorbance in the visible and near-infrared regions. Alternation of the applied potential resulted in rapid (≈0.1–1 s timescale) on/off switching of NIR absorbance at 1300 nm which persisted over thousands of cycles with minimal degradation.     

A new donor‐acceptor type polymeric material from a thiophene derivative and its electrochromic properties

A new electrochromic polymer, poly(2,3,5,8‐tetra(thiophen‐2‐yl)quinoxaline) (PTTQ), was synthesized electrochemically and its electrochromic properties were investigated. The polymer was characterized by Cyclic Voltammetry, Fourier Transform infrared spectroscopy, UV‐Vis‐NIR Spectroscopy, and colorimetry. Spectroelectrochemistry analysis demonstrated that the polymer can undergo both p‐ and true n‐type doping processes. The polymer, (PTTQ), has three accessible color states: an oxidized transmissive, a neutral light bluish‐green, and a reduced transmissive light gray. Switching ability of the polymer was evaluated by kinetic studies. The polymer revealed an excellent optical contrast of 98% in the NIR region. Outstanding optical contrast in the NIR region, high stability and fast switching times make this polymer an excellent candidate for NIR device applications. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3723–3731, 2008     

Synthesis, characterization and electrochromic properties of copolymer of 3-{[4-(thien-3-yl-methoxy)phenoxy]methyl}thiophene with thiophene

(3-{[4-(Thien-3-yl-methoxy)phenoxy]methyl}thiophene) (TMPMT) was synthesized via the reaction of 3-bromomethylthiophene with hydroquinone and characterized by nuclear magnetic resonance (NMR) and Fourier transform infrared spectroscopy (FTIR). Electrochemical copolymerization of TMPMT with thiophene in acetonitrile/boron trifluoride diethyl etherate (AN/BFEE) solvent mixture was achieved using tetrabutylammonium tetrafluoroborate (TBAFB) as the supporting electrolyte. Resulting copolymer was characterized via cyclic voltammetry (CV), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), four probe technique conductivity measurement and UV-Vis spectroscopy. Spectroelectrochemical analysis of the copolymer [P(TTMT-co-Th)] revealed that π-π^∗ electronic transition occurs at 427 nm with a band gap value of 2.20 eV. Copolymer gives brown color at the fully reduced state whereas; at fully oxidized state the film has a gray-blue color. Kinetic studies were carried out at the maximum contrast wavelength upon measuring the percent transmittance, T% (7.6%) and switching time (2.0 s) to examine the switching ability of the copolymer. Dual type electrochromic device (ECD) of P(TMPMT-co-Th) and poly(3,4-ethylenedioxythiophene) (PEDOT) was constructed. Spectroelectrochemistry, switching ability, open circuit memory and stability of the device were examined by UV-Vis spectroscopy and cyclic voltammetry. The device switches between brown and blue at switching voltages of 0.0 V and 2.8 V with a short switching time of 1.4 s.     

Transport properties of thermo-responsive ion track membranes

The permeation of orange G (MW 452), methylene blue (MW 319), and bovine albumin (MW 68000), through thermo-responsive ion track membranes was studied. For this purpose, poly-N-isopropylacrylamide (poly-NIPAAm) hydro-gel was chemically grafted onto single/multi-pore ion track membranes of poly(ethylene terephthalate) (PET).The local transport properties were studied by measuring the electrical current through single pore membranes. It was found that the incorporation of the hydro-gel into the pores does not influence the phase transition temperature. The switching of the responsive membrane was reversible over 200 switching cycles applied during 30–50 days. The closed pores represent a physical barrier excluding organic molecules larger than 2±0.2 nm. This fact is based on the size exclusion method using mixtures of polyethylene glycol (PEG) of various molecular weights and 0.1 N potassium chloride.The global transport properties were studied using multi-pore membranes with 5×10⁵ to 5×10⁷ pores per cm² and pore diameters between 0.6 and 4.5 μm. For bovin insulin permeation in the open state was 35 times above the level of the closed state corresponding to the detection limit of the used permeation cell. In the open state the transport rates of the solvent and the solute were identical implying that the free space in the open pores was larger than the size of the permeating bovine albumin molecules (about 7.3 nm). The linear relation between pressure and mass current enabled to determine an effective open-pore diameter between 0.2 and 1 μm. In the open state, the membrane this is not molecular selective.     

Performance and defects in phosphorescent organic light-emitting diodes

Phosphorescent heavy metal complexes can utilize both singlet and triplet excitons and thus are interesting for doping polymer to obtain highly efficient organic light-emitting diodes. In this study, we have investigated devices using a new phosphorescent–metal complex containing fluorene and platinum added to a luminescent polymer blend, composed of 2-(4-biphenylyl)-5-(4-tert-butyl-phenyl)-(1,3,4-oxadiazole) (PBD) and poly(9-vinylcarbazole) (PVK). The performance of devices (luminance and yield) is measured in indium tin oxide (ITO)/poly(3-4 ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS)/(PVK–PBD-complex)/Al diodes. The devices emit an orange light with a brightness of 607 cd/m² and an external quantum efficiency of 0.28 cd/A at 25 V. In order to investigate the structural modifications of the polymer by the incorporation of phosphorescent–metal complex, we have studied the defect states in diodes by charge-based Deep Level Transient Spectroscopy (Q-DLTS). Analysis of Q-DLTS spectra obtained in undoped and doped devices, revealed at least three trap levels distributed in the range 0.2–0.5 eV within the band gap of the hybrid composite with trap density in the range around 10¹⁶ cm^?3. Incorporation of Pt complex into the polymer blend modified the trap states by reducing the density of traps in the blend and by creating new trap levels in the band gap.     

Preparation of boron-doped diamond nanowires and their application for sensitive electrochemical detection of tryptophan

The paper reports on the fabrication and electrochemical investigation of boron-doped diamond nanowires (BDD NWs) electrodes. The nanowires were obtained directly from highly doped polycrystalline diamond substrates using reactive ion etching (RIE) with oxygen plasma. The technique does not require any complicated processing steps such as mask deposition or template removal. The influence of the surface state on the electrochemical characteristics is discussed. The interface with the most favourable electrochemical response is investigated for the detection of tryptophan using differential pulse voltammetry. A detection limit of 5 × 10^?7 M was obtained on oxidized BDD NWs, as compared to 1 × 10^?5 M recorded on planar oxidized boron-doped diamond interfaces.