基于小波变换-遗传算法-偏最小二乘的草莓糖度检测研究

采用近红外漫反射光谱分析技术,对草莓糖度进行了无损检测研究。利用便携式近红外光谱仪采集草莓样品在600～1 100 nm波段内的漫反射光谱数据。首先利用小波变换(WT)多分辨率方法对光谱数据进行去噪预处理,然后利用遗传算法(GA)优选特征波长,最后运用偏最小二乘法(PLS)建立草莓糖度的WT-GA-PLS校正模型。该模型校正集的相关系数R_C为0.9395,校正集的均方根误差RMSEC为0.1615,预测集的相关系数R_P为0.9652,预测集的均方根误差EMSEP为0.5042。与全光谱模型(FS-PLS)和小波变换模型(WT-PLS)相比,该模型预测能力更强,稳健性更优。     

PDS用于不同温度下的近红外光谱模型传递研究

采用合适的计算方法可降低测定环境对近红外光谱校正模型稳健性的影响。该文以喷气燃料为研究对象,考察了分段直接校正算法对所建模型预测结果的影响,通过选择转移样品数及窗口宽度,建立了最佳的校正模型和光谱转移参数。结果表明,在20℃下建立近红外光谱校正模型,直接预测30℃下喷气燃料的密度,预测集样品均方根误差（RMSEP）为0.2031,而30℃近红外光谱采用分段直接校正算法模型转移后,预测集样品均方根误差（RMSEP）降低为0.1354,预测结果得到明显改善,有效地解决了样品温度对近红外光谱分析结果的影响。     

应用近红外漫反射光谱法的猕猴桃品质无损检测北大核心CSCD

应用近红外漫反射光谱技术和化学计量学,研究成熟期猕猴桃内部品质与其近红外漫反射光谱之间的关系。在室温(24±2)℃下,采集猕猴桃赤道区域不同测试部位在4 000~10 000 cm^(-1)范围内的光谱数据,用基于平滑处理、归一化及基线校正的组合式处理方法对原始光谱进行预处理;另应用偏最小二乘(PLS)法、主成分回归法和多元线性回归法等方法分别建立猕猴桃硬度、可溶性固形物含量(SSC)的校正模型。结果表明:采用组合预处理方法和PLS法建立的校正模型精度最高;硬度校正集相关系数R_c、均方根误差RMSEC和预测集相关系数R_p、均方根误差RMSEP达到了0.976 5,0.548 3,0.943 2,0.612 7;SSC校正集相关系数R_c、均方根误差RMSEC和预测集相关系数R_p、均方根误差RMSEP达到了0.916 6,0.539 6,0.901 2,0.619 0;试验结果验证了本法的可行性。     

近红外光谱法快速鉴定油菜杂交种的纯度

建立近红外光谱技术测定油菜杂交种纯度的方法。考察了样品杯类型、光谱预处理方法和波长范围对近红外模型预测性能的影响。结果发现,由不同样品杯采集近红外光谱所建立的校正模型,其预测性能存在较大的差异,旋转杯明显优于安瓿瓶;采用消除常数偏移量对光谱进行预处理能有效地提取光谱信息,选择5 000~8 000 cm–1波数范围作为建模谱区,其包含的有效信息率最高。在最佳条件下建立油菜杂交种纯度的校正模型,其决定系数(R2)为0.980 0,交互验证均方根误差(RMSECV)为0.008 59。利用该模型对预测集进行测定,预期均方根误差(RMSEP)为0.007 59,表明该模型具有很好的预测性能,近红外光谱法用于杂交种纯度的鉴定是可行的。     

应用近红外漫反射光谱法的猕猴桃品质无损检测

应用近红外漫反射光谱技术和化学计量学,研究成熟期猕猴桃内部品质与其近红外漫反射光谱之间的关系。在室温(24±2)℃下,采集猕猴桃赤道区域不同测试部位在4 000~10 000 cm~(-1)范围内的光谱数据,用基于平滑处理、归一化及基线校正的组合式处理方法对原始光谱进行预处理;另应用偏最小二乘(PLS)法、主成分回归法和多元线性回归法等方法分别建立猕猴桃硬度、可溶性固形物含量(SSC)的校正模型。结果表明:采用组合预处理方法和PLS法建立的校正模型精度最高;硬度校正集相关系数R_c、均方根误差RMSEC和预测集相关系数R_p、均方根误差RMSEP达到了0.976 5,0.548 3,0.943 2,0.612 7;SSC校正集相关系数R_c、均方根误差RMSEC和预测集相关系数R_p、均方根误差RMSEP达到了0.916 6,0.539 6,0.901 2,0.619 0;试验结果验证了本法的可行性。     

近红外光谱测定溶液中甲醇的含量

测量了含微量甲醇(体积分数为0.04%～0.24%)的系列乙醇水溶液的近红外光谱,利用近红外光谱分析建立了预测甲醇含量的定量分析模型。比较了用外部检验法(Test Set-Validation)和交叉检验法(Cross-Validaton)建立的数学模型,研究了使用外部检验法时,校正集和检验集样品数的改变对模型预测结果的影响。结果发现,当校正集样品数为15检验集样品数为6(总样品数为21)时,使用外部检验法建立的数学模型预测结果较好,其校正集的均方根误差和检验集的预测均方根误差(分别为RMSEE和RMSEP)均较小(分别为0.0115和0.0105),而且很接近。结果表明,近红外光谱方法简单,准确而且实用。     

基于可见/近红外透射光谱的番茄红素含量无损检测方法研究

针对番茄内外部结构特征,搭建了可见/近红外透射检测系统,利用完整番茄透射光谱信息,对番茄红素含量进行无损伤快速检测研究。采集的原始光谱曲线经去趋势(DT)、标准正态变量变换(SNV)、多元散射校正(MSC)、归一化(NOR)、一阶导数(FD)预处理后分别用偏最小二乘(PLS)进行建模分析。其中SNV预处理后的模型效果最好,校正集和验证集相关系数分别为0.9771和0.9504,校正集和验证集均方根误差为0.9711和1.0496 mg/kg。为进一步提高模型的精度和稳定性,采用无信息变量消除法(UVE)、连续投影算法(SPA)、竞争性自适应重加权算法(CARS)3种方法单独或联合处理(UVE-SPA,UVE-CARS),对全光谱进行变量优选。经UVE-CARS处理后番茄红素预测模型效果最好,其校正集和验证集相关系数分别提高至0.9830和0.9741,均方根误差分别降低至0.6919和0.7680 mg/kg。最后,选用25个番茄样品对所建立模型进行了外部验证,UVE-CARS-PLS模型的预测集相关系数为0.9812,预测集均方根误差为0.7071 mg/kg,平均相对误差为4.3%。而作为比较的PLS模型的预测集相关系数为0.951,均方根误差为1.0610 mg/kg,平均相对误差6.0%,相比于全光谱PLS模型,UVE-CARS可以很大程度地简化模型,提高模型精度,降低检测的误差限。结果表明,基于自行搭建的番茄可见/近红外透射检测系统结合光谱处理方法,可以实现对生鲜番茄中番茄红素含量的快速、无损检测,为番茄红素定量检测提供了新方法。     

近红外光谱技术用于花生油中棕榈油含量的测定

本文采用近红外光谱技术采集样品的近红外光谱数据,光谱经一阶求导后,采用偏最小二乘法(PLS)建立花生油中棕榈油含量的定标模型,并用交互验证法对模型进行了验证。模型相关系数为0.9963,校正均方根(RMSEC)为0.937。该模型应用于实际样品的检测,结果令人满意。     

基于近红外光谱法的定量分析模型快速预测蕨菜中总黄酮的含量

采用近红外光谱法结合偏最小二乘法构建蕨菜中总黄酮含量的快速无损测定方法。取蕨菜样品140份,采用傅里叶变换近红外光谱仪采集4 000～11 500 cm^-1波段内近红外光谱,以一阶导数预处理原始光谱,设置主因子数为10,在6 100～7 500 cm^-1和5 400～6 000 cm^-1波段内建模。结果表明：校正集定量分析模型的校正均方根误差(RMSEC)为0.078,交叉验证决定系数(R²)为0.991 9;验证集定量分析模型的预测均方根误差(RMSEP)为0.125,R²为0.984 1,说明所建模型性能较优。分别以定量分析模型和紫外-可见(UV-Vis)分光光度法分析完全外部验证集样品,预测回收率(预测值和测定值比值的百分数)接近100%,说明所建模型的预测准确度较高,可用于蕨菜中总黄酮的快速、准确测定。     

近红外光谱法分析盐酸雷尼替丁胶囊

应用化学计量学与近红外光谱方法相结合,分析了盐酸雷尼替丁胶囊。以交叉验证均方根误差(RMSECV)、预测均方根误差(RMSEP)和决定系数为评价指标,分别建立了上述药物的定性和定量分析的模型。在定性判别分析方面,当采用多元散射校正(MSC)和一阶导数法对NIRS谱图进行预处理,并确定样品判别模型的主成分数为6,波长范围在波数为9 090.92~4 008.81cm~(-1)之间时误判数为0;在定量分析方面,选定的建模条件为:光谱的预处理方法为一阶导数法,建模波段在9 090.92~4 008.81cm~(-1)波数之间,主因子数为5。对13批次样品进行验证,测定值与预测值的相对偏差在-4.20%~4.04%之间。     

激光诱导击穿光谱(LIBS)结合机器学习算法快速测定石油焦中微量元素

石油焦中微量元素对其作为预焙阳极的性能起着决定性的作用。首先，通过基于LIBS光谱构建用于石油焦中铁(Fe)和铜(Cu)定量分析的PLS校正模型。然后，考察了不同光谱预处理(归一化、多元散射校正、标准正态变换、一阶导数和二阶导数)以及变量选择算法(粒子群优化算法和变量重要性投影)对PLS校正模型预测性能的影响。建立了一种基于激光诱导击穿光谱(Laser-induced breakdown spectroscopy, LIBS)结合偏最小二乘(Partial least squares, PLS)的石油焦中微量元素定量分析方法。结果显示，与其他PLS校正模型相比，基于二阶导数和变量重要性投影的PLS模型对Fe的预测性能最优，最优的交叉验证相关系数(R-squared cross validation,R²cv)为0.966 7,均方根误差(Root mean squared error cross validation, RMSEcv)为10.282 1 mg/kg,预测集的相关系数(R-squared prediction,R²p)为0.86...     

Screening of humic and fulvic acids in estuarine sediments by near-infrared spectrometry

Diffuse reflectance near-infrared spectroscopy (NIR) combined with partial least squares (PLS) data treatment has been employed for the rapid and nondestructive determination of sedimentary humic substances. Forty one samples of surface estuarine sediments, taken during distinct seasonal periods from different locations across Ria de Arousa (northwest of Spain), were scanned at wavelengths from 833 to 2,976 nm (12,000 to 3,360 cm⁻¹). Twenty four samples were randomly selected, from previous hierarchical cluster analysis of their NIR spectra, for the calibration set, and the 17 remaining samples were assigned to the validation set. NIR spectra of calibration samples were correlated to measured values of humic acids (HAs) and fulvic acids (FAs), which ranged from 1.53 to 28.17 mg/g and from 0.37 to 2.45 mg/g, respectively, using PLS regression and multiplicative scattering correction on the raw and first-derivative NIR spectra, respectively. Low root mean square error of prediction values of 4.3 mg HA/g sediment and 0.25 mg FA/g sediment were obtained. Good residual prediction deviation values of 1.16 and 1.2 were obtained for HA and FA, respectively, allowing the PLS models built to be considered as appropriate tools for screening purposes. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

白酒基酒中酮类物质的近红外光谱检测方法

应用近红外光谱技术建立了白酒基酒中2,3-丁二酮和3-羟基-2-丁酮的快速检测模型。从洛阳杜康酒厂选取182个白酒基酒样品为材料,运用气相色谱法测得两种物质的化学值,同时采集其在12 000~4 000 cm-1范围内的光谱数据,采用偏最小二乘法(PLS)结合内部交叉验证建立校正模型。通过对比不同光谱预处理下PLS模型效果对其进行优化,确定2,3-丁二酮和3-羟基-2 丁酮的最佳预处理方法分别为一阶导数+多元散射校正和二阶导数,最佳光谱区间分别为9 403.2~7 497.9 cm-1和9 403.2~7 497.9 cm-1+6 101.7~5 449.8 cm-1。优化后2,3-丁二酮和3 羟基-2-丁酮校正集样品的化学值和近红外预测值的决定系数(R2)分别为0.960 2和0.963 2,交叉验证均方根误差(RMSECV)分别为0.39、0.22 mg/100 mL;通过外部检验,验证集样品的R2分别为0.957 6和0.957 8,预测均方根误差(RMSEP)分别为0.40、0.24 mg/100 mL。结果表明,应用近红外光谱技术结合化学计量学方法所建立的模型有较高的准确度,能够满足白酒生产中酮类物质的快速检测需要。     

Chemometric determination of arsenic and lead in untreated powdered red paprika by diffuse reflectance near-infrared spectroscopy

It has been evaluated the potential of near-infrared (NIR) diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) as a way for non-destructive measurement of trace elements at μg kg⁻¹ level in foods, with neither physical nor chemical pre-treatment. Predictive models were developed using partial least-square (PLS) multivariate approaches based on first-order derivative spectra. A critical comparison of two spectral pre-treatments, multiplicative signal correction (MSC) and standard normal variate (SNV) was also made. The PLS models built after using SNV provided the best prediction results for the determination of arsenic and lead in powdered red paprika samples. Relative root-mean-square error of prediction (RRMSEP) of 23% for both metals, arsenic and lead, were found in this study using 20 well characterized samples for calibration and 13 additional samples as validation set. Results derived from this study showed that NIR diffuse reflectance spectroscopy combined with the appropriate chemometric tools could be considered as an useful screening tool for a rapid determination of As and Pb at concentration level of the order of hundred μg kg⁻¹.     

Fast determination of trace dimethyl fumarate in milk with near infrared spectroscopy following fluidized bed enrichment

Near infrared spectroscopy (NIRS) has been proved to be a powerful analytical tool in different fields. However, because of the low sensitivity in near infrared region, it is a significant challenge to detect trace analytes with normal NIRS technique. A novel enrichment technique called fluidized bed enrichment has been developed recently to improve sensitivity of NIRS which allows a large volume solution to pass through within a short time. In this paper, fluidized bed enrichment method was applied in the determination of trace dimethyl fumarate in milk. Macroporous styrene resin HZ-816 was used as adsorbent material, and 1?L solution of dimethyl fumarate was run to pass through the material for concentration. The milk sample was pretreated to remove interference matters such as protein, fat, and then passed through the material for enrichment; after that, diffuse reflection NIR spectra were measured for the analyte concentrated on the material directly without any elution process. The enrichment and spectral measurement procedures were easy to operate. NIR spectra in 900–1,700?nm were collected for dimethyl fumarate solutions in the concentration range of 0.506–5.060?μg/mL and then used for multivariate calibration with partial least squares (PLS) regression. Spectral pretreatment methods such as multiplicative scatter correction, first derivative, second derivative, and their combinations were carried out to select the optimal PLS model. Root mean square error of cross-validation calculated by leave-one-out cross-validation is 0.430?μg/mL with ten PLS factors. Ten samples in an independent test set were predicted by the model with the mean relative error of 5.33?%. From the results shown in this work, it can be concluded that the NIR technique coupled with on-line enrichment method can be expanded for the determination of trace analytes, and its applications in real liquid samples like milk and juice may also be feasible.     

Influence of data pre-processing on the quantitative determination of the ash content and lipids in roasted coffee by near infrared spectroscopy

In near-infrared (NIR) measurements, some physical features of the sample can be responsible for effects like light scattering, which lead to systematic variations unrelated to the studied responses. These errors can disturb the robustness and reliability of multivariate calibration models. Several mathematical treatments are usually applied to remove systematic noise in data, being the most common derivation, standard normal variate (SNV) and multiplicative scatter correction (MSC). New mathematical treatments, such as orthogonal signal correction (OSC) and direct orthogonal signal correction (DOSC), have been developed to minimize the variability unrelated to the response in spectral data. In this work, these two new pre-processing methods were applied to a set of roasted coffee NIR spectra. A separate calibration model was developed to quantify the ash content and lipids in roasted coffee samples by PLS regression. The results provided by these correction methods were compared to those obtained with the original data and the data corrected by derivation, SNV and MSC. For both responses, OSC and DOSC treatments gave PLS calibration models with improved prediction abilities (4.9 and 3.3% RMSEP with corrected data versus 7.1 and 8.3% RMSEP with original data, respectively).     

Near-infrared determination of active substance content in intact low-dosage tablets

Near-infrared (NIR) spectroscopy can be applied to determine the active substance content of tablets. Its great advantage lies in the minimal sample preparation required, which helps to reduce the potential for error. The aim of this study is to show the feasibility of this method on low-dosage tablets. The influence of various spectral pretreatments [standard normal variate (SNV), multiplicative scatter correction (MSC), second derivative (D2), orthogonal signal correction (OSC), separately and combined] and regression methods on prediction error are compared. Partial least square (PLS) regression provided better prediction than principal component regression (PCR). SNV was applied to the first data set and SNV and a second derivative to the second set to maximise model accuracy for quantifying the active substance of intact pharmaceutical products using diffuse reflectance NIR. The models yielded standard errors of prediction (SEP) of 0.1768 and 0.0682 mg for the two products. The experiments were conducted with two low-dosage pharmaceutical forms and results of NIR predictions were comparable to currently approved methods. Diffuse reflectance NIR has the potential to become a reliable and robust quality control method for determining active tablet content.     

Improvement of the partial least squares model performance for oral glucose intake experiments by inside mean centering and inside multiplicative signal correction.

Near infrared (NIR) spectroscopy has become a promising technique for the in vivo monitoring of glucose. Several capillary-rich locations in the body, such as the tongue, forearm, and finger, have been used to collect the in vivo spectra of blood glucose. For such an in vivo determination of blood glucose, collected NIR spectra often show some dependence on the measurement conditions and human body features at the location on which a probe touches. If NIR spectra collected for different oral glucose intake experiments, in which the skin of different patients and the measurement conditions may be quite different, are directly used, partial least squares (PLS) models built by using them would often show a large prediction error because of the differences in the skin of patients and the measurement conditions. In the present study, the NIR spectra in the range of 1300-1900 nm were measured by conveniently touching an optical fiber probe on the forearm skin with a system that was developed for in vivo measurements in our previous work. The spectra were calibrated to resolve the problem derived from the difference of patient skin and the measurement conditions by two proposed methods, inside mean centering and inside multiplicative signal correction (MSC). These two methods are different from the normal mean centering and normal multiplicative signal correction (MSC) that are usually performed to spectra in the calibration set, while inside mean centering and inside MSC are performed to the spectra in every oral glucose intake experiment. With this procedure, spectral variations resulted from the measurement conditions, and human body features will be reduced significantly. More than 3000 NIR spectra were collected during 68 oral glucose intake experiments, and calibrated. The development of PLS calibration models using the spectra show that the prediction errors can be greatly reduced. This is a potential chemometric technique with simplicity, rapidity and efficiency in the pretreatment of NIR spectra collected during oral glucose intake experiments.     

Horizontal attenuated total reflection applied to simultaneous determination of ash and protein contents in commercial wheat flour

Partial least-squares (PLS) regression was used to generate various models for the determination of both the protein and the ash contents of wheat flours by using spectroscopic data in the mid-infrared region obtained with a horizontal attenuated total reflectance (HATR) accessory. One hundred samples of wheat flour were used as purchased in the market: 55 for constructing the calibration model and 45 as external samples. The protein content varied between 8.85 and 13.23% and the ash content, between 0.330 and 1.287%, as determined by reference methods. Raw spectra and those corrected by multiplicative signal correction (MSC), first and second derivative spectra, were used as data for building the models. Different pre-treatments, such as mean centered and/or variance scaled (VS) methods, were tested and compared. Very good models were built as judged by the correlation coefficients (R²), root mean square error of calibration (RMSEC), root mean square error of validation (RMSEV) and root mean square error of prediction (RMSEP) that were obtained. Best results were achieved with MSC treated spectra.     

傅立叶变换近红外光谱法快速评价涪陵榨菜品质

应用傅立叶变换近红外光谱技术,建立了评价涪陵榨菜品质的定量分析模型.测定了58份涪陵榨菜的近红外光谱数据,通过光谱预处理方法消除噪声,以偏最小二乘法(PLS)建立回归模型.最终得到评价其品质的水分、总酸(以乳酸计)和氨基酸含量近红外光谱分析模型的决定系数(R2)依次为0.957 8、0.975 4、0.950 4,交叉...