氧气浓度对劣质煤掺混生活污泥燃烧特性的影响

采用热重分析方法研究了劣质煤掺混生活污泥在氧气浓度20％、30％、50％、70％、90％条件下的燃烧特性和动力学特性.随着氧气浓度的增加,失重率曲线DTG向低温区移动.对着火温度、失重率峰值以及对应温度、燃尽温度、混合物燃烧综合特性指数进行了对比分析,并对固定碳燃烧阶段的表观活化能进行了计算,结果表明,提高氧气浓度能显著改善燃烧条件,表观活化能随着氧气浓度的提高而增大,随掺混比的增加而减小.定义燃烧促进因子C.E.F.(Combustion Enhancement Factor)表征燃料内外部燃烧促进条件,在固定碳燃烧段,燃烧促进因子随氧气浓度增加迅速增大,表明增大氧气浓度对燃烧具有良好促进作用.燃烧促进因子C.E.F.与表观活化能之间具有动力学补偿效应.     

生物质型煤在固硫剂条件下的燃烧特性研究

本文研究了生物质型煤在不同Ca/S比和不同生物质加入量下的燃烧特性,并进行了动力学分析.结果表明,固硫型煤的TG,DTG曲线变化趋势相似,都出现两个明显的失重峰挥发分析出阶段和煤焦燃烧阶段.一般在310-320℃范围内挥发分析出达到最大,在520-530℃范围内,煤焦燃烧失重速率最大.由于固硫反应的增重和型煤燃烧的失重的相对变化,导致第二个失重峰变化比较平缓,且失重温度范围较宽.不同Ca/S比的样品试验结果相比,Ca/S=2样品的最大失重点温度要比Ca/S=1.5样品的最大失重点温度要低;同一Ca/S比下,随着生物质量的增加,相应失重峰的峰值增加,最终失重百分比增加.通过动力学分析,生物质型煤在固硫剂条件下的燃烧反应服从燃烧动力学的基本方程表征的规律,对于不同的温度阶段可用不同的一级反应来描述.     

卷烟原料的保润性能研究

采用烘箱法、动态水分吸附分析系统、气相色谱-质谱联用仪(GC-MS)以及电子扫描显微镜技术比较了卷烟原料保润性的差异。结果表明:1原料烟丝平衡含水率为12.68%,膨胀丝为12.45%,混合丝为12.07%,梗丝为11.99%,而且依据不同原料自身结构的不同,填充值差异性明显。2由于原料微结构存在明显性差异,烟丝失水率为7.24%,膨胀丝为7.61%,混合丝为8.37%,梗丝为11.95%,表明了烟丝的物理保润性效果较好。3综合分析原料挥发性成分及含量,烟丝与膨胀丝致香成分含量较多,混合丝次之,梗丝较少。     

不同烟叶热失重特性及燃烧特性分析

为考察烟叶原料加热状态下的热失重及燃烧特性,采用热失重分析(TG)和差示扫描量热分析(DSC)技术分析了不同类型、不同部位和不同产地烟叶原料的热失重特性和燃烧特性。结果表明:1提高升温速率不改变烟叶的热失重特性,但可加快烟叶的质量损失,有利于烟气的快速释放;2烤烟、白肋烟和香料烟的热失重特性具有明显差异,烤烟和香料烟存在4个热失重阶段,白肋烟只存在3个热失重阶段,其中烤烟和香料烟产生烟气和香味物质主要在第2和第3热失重阶段,白肋烟主要在第2热失重阶段,并且烤烟和香料烟相应的失重率高于白肋烟;3各烟叶均存在挥发物燃烧阶段(200~400℃)和炭化物燃烧阶段(400~600℃),并分别对应于各烟叶的后两个失重阶段;4烤烟两个燃烧阶段的着火温度分别在250~280℃和420~460℃之间,白肋烟和香料烟均分别在230~240℃和410~420℃之间。     

生物油/乙醇混合燃料燃烧性能研究

在空气气氛下采用热失重技术研究生物油及其与乙醇混合燃料的燃烧性能,利用Achar微分法和Coats-Redfern积分法结合的方式进行动力学分析,并对热解焦炭的物化特性进行了测量。结果表明,生物油及其与乙醇混合燃料的燃烧可分为三个阶段,即轻组分挥发、重组分裂解和焦炭燃烧;随着升温速率的升高,生物油的挥发性能和燃烧性能提高;随着乙醇质量分数的增加,挥发段和焦炭燃烧段的活化能都呈先减小后增大的趋势;混合燃料中乙醇质量分数不宜超过26%,否则其燃烧段的活化能增大,且热解焦炭所含有机官能团强度变弱,燃烧性能反而变差。     

松木屑与褐煤共气化的TG-FTIR实验研究

利用TG-FTIR对松木屑、褐煤及其混合物的共气化过程及气化产物进行了分析,研究了掺混比例、升温速率以及反应气氛对共气化过程的影响。结果表明,松木屑加入后提高了试样的反应活性,随松木屑比例增加,气化失重速率逐渐降低,CO的开始析出温度及析出峰面积ACO呈降低趋势;较低的升温速率有利于CO和CH4的析出,随着升温速率的增加,DTG曲线向高温侧移动,最大失重速率显著增加,褐煤热解对应的峰逐渐消失;CO2气氛对挥发分析出阶段的失重行为影响不明显;空气气氛时挥发分析出阶段的两个失重峰分别对应挥发分的燃烧和固定碳燃烧,该气氛下没有明显的焦炭气化阶段。     

Study on combustion characteristics of bio-oil/ethanol blends

在空气气氛下采用热失重技术研究生物油及其与乙醇混合燃料的燃烧性能,利用Achar微分法和Coats-Redfern积分法结合的方式进行动力学分析,并对热解焦炭的物化特性进行了测量.结果表明,生物油及其与乙醇混合燃料的燃烧可分为三个阶段,即轻组分挥发、重组分裂解和焦炭燃烧；随着升温速率的升高,生物油的挥发性能和燃烧性能提高；随着乙醇质量分数的增加,挥发段和焦炭燃烧段的活化能都呈先减小后增大的趋势；混合燃料中乙醇质量分数不宜超过26％,否则其燃烧段的活化能增大,且热解焦炭所含有机官能团强度变弱,燃烧性能反而变差.     

膨胀阻燃硬质聚氨酯泡沫塑料热降解及燃烧产烟研究

采用热失重、X-射线光电子能谱分析、氧指数及烟密度测试等方法研究了可膨胀石墨(EG)与聚磷酸铵(APP)复配膨胀阻燃硬质聚氨酯泡沫塑料(RPUF)的热降解、燃烧性能及产烟行为.在此基础上利用锥形量热仪考察了EG/APP对磷酸三(β-氯异丙基)酯(TCPP)阻燃RPUF体系燃烧性能的影响.研究表明,EG与APP间的相互作用导致了EG/APP体系高温阶段失重速率下降、残炭量显著上升;EG/APP与RPUF之间的成炭作用以APP的化学成炭为主.与RPUF比较,RPUF/EG/APP的氧指数由19.8%提高至35.4%的同时,烟密度没有显著上升.对比EG、APP及EG/APP阻燃RPUF,体系残炭量越高、炭层耐热氧化能力越强,氧指数就越大;残炭表面越致密,产烟量就越少.添加EG/APP可显著降低含卤体系RPUF/TCPP的热释放、烟释放及CO释放速率,体现了EG与APP复合体系物理与化学膨胀结合的优势.     

城市污水污泥燃烧特性和动力学特性分析

采用热重分析仪对城市污水污泥进行热重实验,通过TG(热重)、DTG(微分热重)和DSC(差示扫描量热)曲线的分析对比,获得污水污泥热解和燃烧不同阶段的特性。低于250℃,燃烧与热解的热重曲线基本吻合,说明在此之前,失重速率主要受控于有机物的分解以及析出,燃烧过程对失重影响不明显。燃烧DTG曲线呈现“W”峰型,第一个失重速率峰与热解DTG曲线基本对应,高于410℃,燃烧DTG曲线出现显著的加速。采用Coats-Redfern 积分法,假设不同的反应模型进行拟合,推断出污泥燃烧过程中两个DTG峰体现出不同的反应机理。借鉴煤燃烧机理分析认为,污泥燃烧反应初期挥发分的燃烧受控于化学反应速率,随着温度的不断提高,剩余挥发分的燃尽和固定碳的燃烧总反应速率逐渐受扩散因素控制。基于分析所得污泥燃烧机理,采用四个独立的平行反应模型模拟污泥的燃烧过程,拟合曲线与实验数据吻合良好。     

石油焦与煤混合燃料热重分析研究

石油焦与煤混合燃烧是高效处理石油焦的有效方法，作者对选用的石油焦和煤不同配比的混合燃料进行了热重分析研究。使用常压高温热天平研究、分析了各配比混合燃料的热解特性和燃烧特性。并根据化学动力学方法计算了各过程的化学动力学参数，即活化能E和频率因子A0。结果表明，各混合燃料热解起始温度大致相同，随煤焦比减小，挥发分析出速率变缓，最大释放速度所对应的温度升高，最终失重率减小，挥发分释放特性指数减小；随煤焦比增大，混合燃料着火温度和燃尽温度逐渐降低，最大燃烧速率所对应的温度降低，燃烧特性指数增大；随煤焦比减小，活化能和频率因子增大。     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

化学计量中不确定度评定研究进展

测量不确定度是表征合理地赋予被测量之值的分散性的参数。本文针对化学计量不确定度评定基础模型仅适用于线性模型、概率分布为正态分布或缩放位移t分布等局限,介绍了近年来不确定度评定的研究热点:蒙特卡罗方法(Monte Carlo Method,MCM),不确定度评定的来源、评定概念、评估方法及其发展过程,扩大了测量不确定度评定与表示的适用范围。     

微量钙的测定方法研究进展

介绍了1995-2006年期间测定微量和痕量钙的方法,如电感耦合等离子体-原子发射光谱法、原子吸收光谱法以及离子色谱法等的工作原理和特点,并说明了其测定微量钙的应用领域。并对微量钙的测定技术进行了展望(引用文献55篇)。     

Stages of thermal decomposition of sodium oxo-salts of sulphur

Thermal behaviour of sodium oxo-salts of sulphur: Na₂SO₄, Na₂S₂O₇, Na₂S₂O₆, Na₂SO₃, Na₂S₂O₅, Na₂S₂O₄, Na₂S₂O₃, Na₂S₃O₆ and of sulphides Na₂S and Na₂S₂ was studied on heating up to 1000°C. The experiments were performed with anhydrous compounds obtained from commercial products by recrystallisation and dehydration. The stage mechanisms of decomposition of anionic sub-lattices of the salts have been proposed basing on the Górski’s morphological classification of simple species. The thermal stability and the stage decomposition mechanisms were correlated with the structure and the potential chemical properties of the salt anions. The thermal decomposition processes were studied by means of thermal analysis, and the decomposition products were identified by means of X-ray phase analysis.