Determination of Formaldehyde with a Platinum–Palladium–Graphene Nanocomposite Glassy Carbon Electrode

The oxidation of formaldehyde on a platinum (Pt)–palladium (Pd)–graphene nanocomposite glassy carbon electrode prepared by chemical reduction was characterized in 0.5?M sulfuric acid. The surface and morphology of the catalyst were characterized by transmission electron microscopy, Raman spectroscopy, and X-ray diffraction. Bimetallic Pt–Pd nanoparticles were uniformly dispersed on the graphene sheets. Energy-dispersed X-ray spectroscopy was used to characterize the metal composition of the nanocomposite. The electrocatalytical characteristics of the modified electrode were investigated by cyclic voltammetry. The results show that the electrode displayed high activity for the oxidation of formaldehyde in sulfuric acid with a linear relationship from 4.50?µM to 0.180?mM and a detection limit of 2.85?µM. The low detection limit, wide linear dynamic range, and high sensitivity of the modified electrode suggests further applications.     

Metallated porphyrin noncovalent interaction with reduced graphene oxide‐modified electrode for amperometric detection of environmental pollutant hydrazine

A reduced graphene oxide/platinum(II) tetraphenylporphyrin nanocomposite (RGO/Pt‐TPP)‐modified glassy carbon electrode was developed for the selective detection of hydrazine. The RGO/Pt‐TPP nanocomposite was successfully prepared via noncovalent π–π stacking interaction. The prepared nanocomposite was characterized using nuclear magnetic resonance, electrochemical impedance, ultraviolet–visible and Raman spectroscopies, scanning electron microscopy and X‐ray diffraction. The electrochemical detection of hydrazine was performed via cyclic voltammetry and amperometry. The RGO/Pt‐TPP nanocomposite exhibited good electrocatalytic activity towards detection of hydrazine with low overpotential and high oxidation peak current. The fabricated sensor exhibited a wide linear range from 13 nM to 232 μM and a detection limit of 5 nM. In addition, the fabricated sensor selectively detected hydrazine even in the presence of 500‐fold excess of common interfering ions. The fabricated electrode exhibited good sensitivity, stability, repeatability and reproducibility. In addition, the practical applicability of the sensor was evaluated in various water samples with acceptable recoveries.     

Sensitive Electrochemical Determination of Hydrogen Peroxide Using Copper Nanoparticles in a Polyaniline Film on a Glassy Carbon Electrode

Rapid and accurate determination of hydrogen peroxide is necessary in biochemistry and environmental science. In this paper, a sensitive hydrogen peroxide electrochemical sensor was developed by cyclic voltammetry deposition of polyaniline–copper nanocomposite film on a glassy carbon electrode. The synthesized polyaniline/Cu composites were characterized by scanning electron microscopy and X-ray diffraction. With a typical working potential of 0.4?V (versus Ag/AgCl) and a pH value of 6.0, the prepared electrochemical sensor achieved linear range of 1.0–500?µM for hydrogen peroxide detection. A relative standard deviation of 4.9% for n?=?7 and 10.0?µM of H₂O₂ and a limit of detection of 0.33?µM at a signal-to-noise ratio?=?3 were observed. The sensor was successfully used for the analysis of tap water, and a spiked recovery of 93.0?±?2.1% was obtained, further confirming the sensor’s accuracy and feasibility.     

Sensitive and Selective Electrochemical Sensor Based on Molecularly Imprinted Polypyrrole Hybrid Nanocomposites for Tetrabromobisphenol A Detection

Abstract

A sensitive and selective electrochemical sensor based on electropolymerized molecularly imprinted polypyrrole and gold nanoparticles–multiwalled carbon nanotubes (AuNPs–MWCNTs) hybrid nanocomposites was developed for the determination of tetrabromobisphenol A (TBBPA). A glassy carbon electrode (GCE) was modified with MWCNTs, and the AuNPs–MWCNTs/GCE was prepared by an electrodeposition method in HAuCl₄ solution. The AuNPs–MWCNTs nanocomposite showed high electrocatalytic activity, good conductivity, and sufficient reactive sites for the direct electro-oxidation of TBBPA. The molecularly imprinted polymers (MIPs) as recognition elements were synthesized through in situ electro-polymerization of pyrrole as functional monomers in the presence of the TBBPA template molecules. Under the optimal conditions, the developed sensor exhibited good selectivity towards TBBPA compared with structural analogs, high sensitivity, and excellent producibility. The electrochemical responses of the sensor toward TBBPA were obtained in the linear range from 0.5?nM to 1?μM with a limit of detection equal to 0.24?nM at a signal-to-noise ratio of 3.     

Differential pulse anodic stripping voltammetric determination of traces of tin using a glassy carbon electrode modified with bismuth and a film of poly(bromophenol blue)

We report on an anodic stripping voltammetric method for the determination of tin using a glassy carbon electrode modified with bismuth and poly(bromophenol blue). After an accumulation time of 60?s at ?1.20?V (vs. SCE), the response of the electrode to tin in 1.0?M HCl is linear in the concentration ranges from 20 nM to 1.0?μM, and from 1.0?μM to 20?μM, with a detection limit of 7.0 nM (at an SNR of 3) and with relative standard deviations in the order of 3.0–3.8%. The method was validated by comparing the results with those obtained by AAS and successfully applied to the determination of tin in canned food.

Design and Development of a Non-Enzymatic Electrochemical Biosensor for the Detection of Glutathione

Glutathione (GSH-reduced form) is a tripeptide that plays a vital role as an antioxidant to remove xenobiotics in the human body and changes in GSH levels are a marker for the progression of various diseases. In this context, a highly sensitive non-enzymatic electrochemical biosensor for the detection of GSH has been developed using reduced graphene oxide Manganese oxide (rGMnO) nanocomposite as the nano-interface. Initially, graphene oxide was synthesized by Hummer's method and then thermally reduced in the presence of MnO₂ in a blast furnace to obtain rGMnO nanocomposite. The nanocomposite was characterized to validate its structure and morphological properties via Scanning electron microscopy (SEM), X-ray diffraction (XRD), Raman, and X-ray photoelectron spectroscopy (XPS). Cyclic voltammetry and amperometry studies showed that upon the addition of GSH, the Pt/rGMnO modified working electrode exhibited a linear response in the range of 1–100 μM at an input voltage of −0.62 V. The developed sensor was found to have a sensitivity of 0.3256 μA μM⁻¹ and LOD of 970 nM with a recovery of 92–104 % in real blood serum samples.     

Fabrication and Characterization of Carbon Nanotube‐Hydroxyapatite Nanocomposite: Application to Anodic Stripping Voltammetric Determination of Cadmium

A novel chemically modified electrode for stripping determination of cadmium is presented in this paper, based on carbon nanotube‐hydroxyapatite (CNT‐HAP) nanocomposite, which can be prepared by an easy and effective one‐step sonication. The newly synthesized nanocomposite was characterized with FTIR, TEM, and electrochemical methods. Due to the combination of the strong absorption ability of HAP and excellent electroanalytical properties of CNTs, the GC/CNT‐HAP electrode has been successfully used for determination of Cd²⁺ by anodic stripping voltammetry with a linear range of 20 nM–3 μM. The sensitivity and detection limit are 25.6 μA/μM and 4 nM, respectively. The practical application of the proposed electrode has been carried out for the determination of trace levels of Cd²⁺ in real water samples.     

Nonenzymatic amperometric sensor of hydrogen peroxide and glucose based on Pt nanoparticles/ordered mesoporous carbon nanocomposite

A simple and facile synthetic method to incorporate Pt nanoparticles inside the mesopores of ordered mesoporous carbons (OMCs) is reported. The Pt/OMCs nanocomposite was characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, and nitrogen adsorption-desorption. The results show that the incorporation of Pt nanoparticles inside the pores of OMCs does not change the highly ordered two-dimensional hexagonal mesostructure of OMCs matrix. Nonenzymatic amperometric sensor of hydrogen peroxide and glucose based on the Pt/OMCs nanocomposite-modified glassy carbon (GC) electrode is developed. Compared with the original OMCs-modified electrode, the Pt/OMCs-modified electrode displays improved current response towards hydrogen peroxide and gives linear range from 2 to 4212 μM. At an applied potential of −0.08 V, the Pt/OMCs nanocomposite gives linearity in the range of 0.5-4.5 mM glucose in neutral buffered saline solution. This glucose sensor also exhibits good ability of anti-interference to electroactive molecules. The combination the unique properties of Pt nanoparticles and the ordered mesostructure of OMCs matrix guarantees the enhanced response for hydrogen peroxide and glucose.     

Construction of zinc selenide microspheres decorated with octadecylamine-functionalized reduced graphene oxide as an effective catalyst for the dual-mode detection of chloroquine phosphate

Zinc selenide microspheres were constructed using a simple hydrothermal technique at 180°C. It was ultrasonically treated with reduced graphene oxide modified with octadecylamine alkyl amine to form a hybrid nanocomposite. The optical, structural, and functional analysis by ultraviolet (UV) absorbance, X-ray diffraction, Fourier transform infrared spectroscopy, Raman spectroscopy, and X-ray photoelectron spectroscopy revealed the crystal nature of the microspheres and the successful formation of the nanocomposite. Field emission scanning electron microscopy and transmission electron microscopy were done to study the morphological properties of the material. It was further used to fabricate a dual-modality sensor using both electrochemical and absorbance techniques for the detection of antimalarial drug chloroquine phosphate (CQP), which was used for the treatment of COVID-19 (SARS-CoV-2) virus. For electrochemical detection, the sensor showed a very low detection limit of 1.43 nM at a linear working range of 0.199–250.06 μM and a high sensitivity of 43.912 μA/μM/cm². For UV-based detection, the sensor showed a very low detection limit of 6.88 nM at a linear working range of 0.045–7.324 μM. The sensor showed excellent analyte recovery rate for real-time analysis in biological as well as environmental samples. The results suggested that the sensor is effective for the detection of CQP with feasibility for future commercialization.     

Ionic liquid/graphene oxide as a nanocomposite for improving the direct electrochemistry and electrocatalytic activity of glucose oxidase

By combination of 1-ethyl-3-methyl immidazolium ethyl sulfate as a typical room temperature ionic liquid (IL) and graphene oxide (GO) nanosheets, a nanocomposite was introduced for improving the direct electrochemistry and electrocatalytic activity of glucose oxidase (GOx). The enzyme on the IL–GO-modified glassy carbon electrode exhibited a quasireversible cyclic voltammogram corresponding to the flavine adenine dinucleotide/FADH₂ redox prosthetic group of GOx. At the scan rate of 100 mV?s^?1, the enzyme showed a peak-to-peak potential separation of 82 mV and the formal potential of ?463 mV (vs Ag/AgCl in 0.1 M phosphate buffer solution, pH?7.0). The kinetic parameters of the charge transfer rate constant, the electron transfer coefficient, and the apparent Michaelis–Menten constant were calculated as 1.36 s^?1 and 0.35 and 2.47 μM, respectively. When the modified electrode was examined as a biosensor for glucose determination, a linear range of 2.5–45 nM with detection limit of 0.175 nM (signal to noise?=?3) was obtained. The biosensor was stable for 2 months.     

Investigation of electrocatalytic and analytical ability of Pt nanoparticles supported on active carbon modified electrode to analytical determination of glucose

The electrocatalytic and analytical ability to glucose on a highly dispersed Pt nanoparticles supported on active carbon (Pt/C) modified electrode was investigated. The Pt/C nanocomposite was synthesized using a microwave method. The structural characterization and surface morphology of the prepared Pt/C nanocomposite was examined using X-ray diffraction, energy-dispersive X-ray, scanning and transmission electron microscopy. The results show that the Pt nanoparticles with 3–10 nm in diameter are well dispersed on the surface of active carbon. The electrocatalytic and analytical ability of Pt nanoparticles supported on active carbon modified electrode (Pt/C/GCE) was studied using cyclic voltammetry (CV) and chronoamperommetry. The Pt/C/GCE exhibits strong electrocatalytic activity to the glucose oxidation. Under optimal conditions, the Pt/C/GCE performed a current response towards glucose oxidation at a broad concentration range from 0.05 to 11.95 mM. Two linear regions could be observed at 0.05 to 3.5 mM with a sensitivity of 1.29 μA mM^–1 cm^–2 and at 3.5 to 11.95 mM with a sensitivity of 0.85 μA mM^–1 cm^–2, respectively. The Pt/C/GCE exhibits sufficient sensitivity and abilities of anti-interference.     

Fullerene-based anodic stripping voltammetry for simultaneous determination of Hg(II), Cu(II), Pb(II) and Cd(II) in foodstuff

Various carbon nanomaterials for use in anodic stripping voltammetric analysis of Hg(II), Cu(II), Pb(II) and Cd(II) are screened. Graphene, carbon nanotubes, carbon nanofibers and fullerene (C₆₀), dispersed in chitosan (Chit) aqueous solution, are used to modify a glassy carbon electrode (GCE). The fullerene-chitosan modified GCE (C₆₀-Chit/GCE) displays superior performance in terms of simultaneous determination of the above ions. The electrodes and materials are characterized by electrochemical impedance spectroscopy, cyclic voltammetry, scanning electron microscopy, Raman spectroscopy, X-ray diffraction and X-ray photoelectron spectroscopy. The excellent performance of C₆₀-Chit/GCE is attributed to the good electrical conductivity, large surface area, strong adsorption affinity and unique crystalline structure of C₆₀. Using differential pulse anodic stripping voltammetry, the assay has the following features for Hg(II), Cu(II), Pb(II) and Cd(II), respectively: (a) Peak voltages of +0.14, ?0.11, ?0.58 and???0.82 V (vs SCE); (b) linear ranges extending from 0.01–6.0 μM, 0.05–6.0 μM, 0.005–6.0 μM and 0.5–9.0 μM; and (c), detection limits (3σ method) of 3 nM (0.6 ppb), 14 nM (0.9 ppb), 1 nM (0.2 ppb) and 21 nM (2.4 ppb). Moreover, the modified GCE is well reproducible and suitable for long-term usage. The method was successfully applied to the simultaneous determination of these ions in spiked foodstuff.

Open image in new window

Graphical abstract Compared with graphene, carbon nanotubes and carbon nanofibers, an electrode modified with fullerene in chitosan electrode displays superior performance for the simultaneous anodic stripping voltammetric detection of Hg(II), Cu(II), Pb(II) and Cd(II).

     

Synthesis and biological evaluation of Cu(II), Zn(II), and Ni(II) 3-(4-nitrophenyl)acrylic acid complexes with diamines as potential urease inhibitors

Five new Cu(II), Zn(II), and Ni(II) 3-(4-nitrophenyl)acrylic acid complexes were synthesized and evaluated for inhibitory activity on jack bean urease. All five complexes were structurally determined by single crystal X-ray analysis. Compared with the positive reference acetohydroxamic acid (IC₅₀?=?13.25?μM), Cu(II) complexes 3 and 4 showed the strongest inhibitory activity against jack bean urease (IC₅₀?=?1.23 and 1.17?μM). Ni(II) and Zn(II) complexes also exhibited inhibitory activities (IC₅₀?=?10.09–13.10?μM).     

Copper nanoparticles entrapped in SWCNT-PPy nanocomposite on Pt electrode as NOx electrochemical sensor

A highly sensitive NO_x sensor was designed and developed by electrochemical incorporation of copper nanoparticles (CuNP) on single-walled carbon nanotubes (SWCNT)-polypyrrole (PPy) nanocomposite modified Pt electrode. The modified electrodes were characterized by scanning electron microscopy and energy dispersive X-ray analysis. Further, the electrochemical behavior of the CuNP-SWCNT-PPy-Pt electrode was investigated by cyclic voltammetry. It exhibited the characteristic CuNP reversible redox peaks at −0.15 V and −0.3 V vs. Ag/AgCl respectively. The electrocatalytic activity of the CuNP-SWCNT-PPy-Pt electrode towards NO_x is four-fold than the CuNP-PPy-Pt electrode. These results clearly revealed that the SWCNT-PPy nanocomposite facilitated the electron transfer from CuNP to Pt electrode and provided an electrochemical approach for the determination of NO_x. A linear dependence (r² = 0.9946) on the NO_x concentrations ranging from 0.7 to 2000 μM, with a sensitivity of 0.22 ± 0.002 μA μM⁻¹ cm⁻² and detection limit of 0.7 μM was observed for the CuNP-SWCNT-PPy-Pt electrode. In addition, the sensor exhibited good reproducibility and retained stability over a period of one month.     

Comparison of Insulin Determination on NiNPs/chitosan‐ MWCNTs and NiONPs/chitosan‐MWCNTs Modified Pencil Graphite Electrode

The rising amount of patients suffering for diabetes mellitus increases the requirements for effective insulin sensors. Carbon materials are a suitable choice for the development of insulin sensors due to their electrochemical characteristics. Pencil graphite electrodes (PGE) represent the trade‐off between price and excellent conductive properties. The modification of PGE by NiO and Ni nanoparticles fixed by chitosan results in surface area enlargement and improved electrocatalytic properties. This paper is focused on the comparison of different properties of Ni and NiO nanoparticles and their effect on redox reaction mechanism of insulin and detection characteristics. The electrode modified by Ni nanoparticles displays linear range of 1 μM–5 μM (R² 0.80), limit of detection (LOD) of 4.34 μM and sensitivity of 0.12 μA/μM. On the other hand, the electrode modified by NiO nanoparticles displays enhanced electrochemical characteristics such as linear range of 0.05 μM–5 μM (R² 0.99), limit of detection of 260 nM and sensitivity of 0.64 μA/μM. These properties make the NiO nanoparticles modified PGE the appropriate candidate for insulin determination.     

Antifungal activity,DNA and lysozyme binding affinity of Pd(II) and Pt(II) complexes bearing N,N-pyridylbenzimidazole ligand

Abstract

The lysozyme- and DNA-binding affinities of the biologically active cisplatin analogues, Pd(II) (1) and Pt(II) (2) complexes of functionalized N,N-pyridylbenzimidazole ligand, are reported. The electronic transitions were studied by time-dependent density functional theory. Complex 1 exhibits interesting antifungal activity against Candida albicans (MIC?=?32?μg?mL^?1; 64?nM) and Cryptococcus neoformans (MIC?=?16?μg?mL^?1, 32?nM). Complex 1 is covalently bound to DNA and lysozyme via the elimination of the chloride ligand(s). When complex 2 interacts with lysozyme, two adduct peaks are observed in the mass spectrum corresponding to binding of Pt(II) ion to lysozyme.     

Simultaneous voltammetric determination of 2-nitrophenol and 4-nitrophenol based on an acetylene black paste electrode modified with a graphene-chitosan composite

We describe a simple and sensitive voltammetric method for the simultaneous determination of 2-nitrophenol and 4-nitrophenol. It is based on the use of an acetylene black paste electrode modified with a graphene-chitosan composite film (denoted as Gr-Chit/ABPE). The reduction peak currents of 2-nitrophenol (at ?252 mV) and of 4-nitrophenol (at ?340 mV) in pH 1.0 solution increase significantly at the Gr-Chit/ABPE in comparison to a bare ABPE. Factors affecting sensitivity were optimized and a linear relationship is found between peak current and the concentrations of 2-nitrophenol (in the 0.4 μM to 80 μM range) and for 4-nitrophenol (in the 0.1 μM to 80 μM range). The detection limits (at an SNR of 3 and after a 30-s accumulation time) are 200 nM for 2-nitrophenol and 80 nM for 4-nitrophenol, respectively. The modified electrode was successfully applied to the direct and parallel determination of 2-nitrophenol and 4-nitrophenol in spiked water samples.

Graphene–Pt nanocomposite for nonenzymatic detection of hydrogen peroxide with enhanced sensitivity

A sensitive hydrogen peroxide (H₂O₂) sensor was fabricated based on graphene–Pt (GN–Pt) nanocomposite. The GN–Pt was synthesized by photochemical reduction of K₂PtCl₄ on GNs, and characterized by atomic force microscope (AFM), transmission electron microscope (TEM), and energy-dispersive X-ray spectroscopy (EDS). Electrochemical investigations indicated that the GN–Pt exhibited a high peak current and low overpotential towards the reduction of H₂O₂. The GN–Pt modified glass carbon electrode displayed a wide linear range (2–710 μM), low limit of detection (0.5 μM) and good selectivity for detection of H₂O₂ with a much higher sensitivity than that of Pt nanoparticles or graphene modified electrode.     

Hydroxyapatite Wrapped Multiwalled Carbon Nanotubes/Ionic Liquid Composite Electrode: A High Performance Sensor for Trace Determination of Lead Ions

A nanocomposite consisting of multiwalled carbon nanotubes wrapped with hydroxyapatite (HA/MWCNTs) was used in the construction of a new composite paste electrode using an ionic liquid as the binder. The stable surface in aqueous solutions as well as the high sorptive behaviors towards heavy metal ions and the favorable charge transfer make the electrode highly efficient especially for stripping or adsorptive analysis. The analysis of Pb²⁺ as a model of heavy metal ions has been performed. Good sensitivity, detection limit, selectivity and reproducibility were obtained for the suggested sensor. The linear range of the electrode response covered four orders of magnitude (1 nM–10 µM), in two linear ranges. The obtained detection limit for Pb²⁺ was 2×10^?11 M.     

Electrochemical Determination of Uric Acid Using a Multiwalled Carbon Nanotube Platinum–Nickel Alloy Glassy Carbon Electrode

Platinum–nickel nanoparticles were synthesized by a reduction procedure. The Pt–Ni/C composite was characterized by X-ray diffraction, infrared spectroscopy, transmission electron microscopy, and electrochemical analysis. The measurements show that the Pt–Ni/multiwalled carbon nanotubes provided higher electrocatalytic activity for the oxidation of uric acid than Pt–Ni/carbon black. The sensor prepared from the characterized material provided a long linear dynamic range from 0.1 to 240.4?µM with a detection limit of 0.03?µM and a sensitivity of 41.21?µA?mM^?1?cm^?2. The reported modified electrode also provided excellent selectivity, good stability, and satisfactory reproducibility for the determination of uric acid.