Fast fabrication of superabsorbent polyampholytic nanocomposite hydrogels via plasma‐ignited frontal polymerization

We report the facile synthesis of poly(VI‐co‐MAA) superabsorbent polyampholytic hydrogels (VI = N‐vinylimidazole, MAA = methacrylic acid) via plasma‐ignited frontal polymerization (PIFP). On igniting the top surface of the reactants with air plasma, frontal polymerization occurred and poly(VI‐co‐MAA) hydrogels were obtained within minutes. The preparation parameters were investigated, along with swelling capacity, morphology, and chemical structures of poly(VI‐co‐MAA) hydrogels. Interestingly, the hydrogels are superabsorbent in water and show ampholytic characteristic toward pH. Moreover, the hydrogels are able to capture cationic dyes through electrostatic interaction, offering the potential for further development as dye adsorbents for water purification. In addition, nanocomposite hydrogels were obtained by embedding quantum dots (carbon dots or CdS nanocrystals) into the polymer matrix, which endows the nanocomposite hydrogels with favorable fluorescence and potential applications in bioimaging and biosensing. The results indicate that FP can be applied as an alternative means for facile synthesis of multifunctional hydrogels with additional efficiency and energy‐saving. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 912–920     

In situ access to white light‐emitting fluorescent polymer nanocomposites via plasma‐ignited frontal polymerization

We describe a facile fabrication of white light‐emitting cadmium sulfide (CdS)‐poly(HEA‐co‐NVK) nanocomposites [2‐hydroxyethyl acrylate (HEA) and N‐vinylcarbazole (NVK)] via plasma‐ignited frontal polymerization (PIFP), a novel and rapid reaction mode of converting monomers into polymers in minutes. Frontal polymerization was initiated by igniting the upper side of the reactant with plasma. Once initiated, no additional energy was required for the polymerization to occur. The chemical functional groups of the as‐prepared nanocomposites were thoroughly investigated using Fourier transform infrared spectra. The dependence of the front velocity and front temperature on the initiator concentration and weight ratios of HEA/NVK was also investigated in detail. Perhaps more interestingly, the white light‐emitting materials synthesized by ingeniously incorporating the compensating colors of yellow emitting from 3‐(trimethoxysilyl)‐1‐propanethiol‐capped CdS nanocrystals and blue emitting from carbazole‐containing polymer were conveniently applied onto a commercial UV light‐emitting diode (LED) to generate white LEDs. The subtle change in the weight ratios of CdS/NVK can significantly impact the color hue. The white light becomes gradually colder with the increase of NVK, but becomes gradually warmer with the increase concentration of CdS nanocrystals. In a broad perspective, these white light‐emitting materials designed by PIFP approach will open a new pathway to develop “QD‐polymer nanocomposite down‐conversion LED” in a fast and efficient way. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Facile synthesis of amphiphilic gels by frontal free‐radical polymerization

We report a new facile strategy for quickly synthesizing poly(2‐hydroxyethyl acrylate‐co‐vinyl versatate) amphiphilic gels with excellent physicochemical properties by frontal free‐radical polymerization. The appropriate amounts of 2‐hydroxyethyl acrylate, vinyl versatate (VeoVa 9) and ammonium persulfate initiator were mixed together at ambient temperature in the presence of N‐methyl‐2‐pyrrolidone as the solvent medium. Frontal polymerization (FP) was initiated by heating the wall of the tube with a soldering iron. Once initiated, no further energy was required for the polymerization to occur. The dependence of the front velocity and front temperature on the initiator concentration was investigated. The front temperatures were between 132 and 157 °C, depending on the initiator concentration. The morphology, swelling rate, and swelling behavior of amphiphilic gels prepared via FP were comparatively investigated on the basis of scanning electron microscopy, water contact angle, and swelling measurements. Results show that the amphiphilic gels prepared via FP behave with good swelling capacity both in water and organic solvents. The FP can be exploited as an alternative means for synthesis of amphiphilic gels with additional advantages of fast and efficient way. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 823–831, 2010     

Facile synthesis of self‐healing gel via magnetocaloric bottom‐ignited frontal polymerization

A series of the self‐healing gels facilely fabricated by VI (N‐vinyl imidazole) and MAH‐β‐CD (β‐cyclodextrin grafted vinyl carboxylic acid groups) via bottom‐ignited frontal polymerization (BIFP) initiated by magnetocaloric effect. Once ignited the bottom phase, the heat upward propagates to generate the “front” in the upper phase. Then, no further energy is added to maintain the reaction and the whole polymerization process experiences within minutes. In this system, the dependence of frontal velocity and temperature, along with morphology, swelling capacity, mechanical property, and self‐healing efficiency, on the preparation parameters is investigated. Interestingly, the gels show good swelling capacity in the organic solvent, comparatively almost no absorption in water. Moreover, the as‐prepared gels exhibit excellent auto‐healing properties without any external stimuli at ambient temperature. The healed sample possesses 97% recovery of its tensile strength after 8 h healing time, which relies largely on the host–guest interaction between VI and MAH‐β‐CD. The results demonstrate that FP can be utilized as an efficient and energy‐saving method to synthesize self‐healing supramolecular gels. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 2585–2593     

First solvent‐free synthesis of poly(N‐methylolacrylamide) via frontal free‐radical polymerization

We report the first synthesis of poly (N‐methylolacrylamide) (PNMA) via free‐radical frontal polymerization (FP) with solid monomers at ambient pressure. The appropriate amounts of reactants (N‐methylolacrylamide) (NMA) and initiator (ammonium persulfate) were mixed together at ambient temperature without solvent. FP was initiated by heating the wall of the tube with a soldering iron, and the resultant hot fronts were allowed to self‐propagate throughout the reaction vessel. Once initiated, no further energy was required for polymerization to occur. To suppress the fingers of molten monomer, a small amount of nanosilica was added. We also produced PNMA with dimethyl sulfoxide (DMSO) or N‐methyl‐2‐pyrrolidone, as solvent by FP, to study the macrokinetics in FP of PNMA without fillers. The front velocity and front temperature dependence on the ammonium persulfate and N‐methyl‐2‐pyrrolidone concentration were investigated. The polymer was analyzed by thermogravimetric analysis. Results show that without postpolymerization solvent removal, waste production can be reduced. Solvent‐free FP could be exploited as a means for preparation of PNMA with the potential advantage of higher throughput than solvent‐based methods. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4322–4330, 2007     

Facile synthesis of fluorescent quantum dot‐polymer nanocomposites via frontal polymerization

We report an available approach for quickly fabricating CdS QD‐polymer nanocomposites via frontal polymerization (FP). First, we synthesized (3‐mercaptopropyl)‐1‐trimethoxysilane (MPS)‐capped CdS quantum dots (QDs). With these MPS‐capped CdS QDs containing mercapto groups, MPS‐capped CdS QDs can be easily incorporated into a poly(N‐methylolacrylamide) (PNMA) matrix via FP. A variety of features for preparing QD‐polymer nanocomposites, such as initiator concentration and CdS concentration, were thoroughly investigated. The fluorescence properties of QD‐polymer nanocomposites prepared via FP are comparatively investigated on the basis of ultraviolet–visible (UV–vis) spectra and photoluminescence (PL) spectra. Results show that the PL intensity of QD‐polymer nanocomposites prepared via the FP method is superior to that obtained by the traditional batch polymerization (BP) method. In addition, by measuring the changes of PL intensity of the samples immersed in different concentrations of copper acetate solution, we found the QD‐polymer nanocomposites can be ultrasensitive to copper ions. This FP process can be exploited as a facile and rapid way for synthesis QD‐polymer nanocomposites on a large scale, avoiding the fluorescence quenching of nanocrystals during incorporation nanocrystals into polymer matrices. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2170–2177, 2010     

Facile and quick synthesis of poly(N‐methylolacrylamide)/polyhedral oligomeric silsesquioxane graft copolymer hybrids via frontal polymerization

We report on a new strategy for fabricating well‐defined POSS‐based polymeric materials with and without solvent by frontal polymerization (FP) at ambient pressure. First, we functionalize polyhedral oligomeric silsesquioxane (POSS) with isophorone diisocyanate (IPDI). With these functionalized POSS‐containing isocyanate groups, POSS can be easily incorporated into a poly(N‐methylolacrylamide) (PNMA) matrix via FP in situ. Constant velocity FP is observed without significant bulk polymerization. The morphology and thermal properties of POSS‐based hybrid polymers prepared via FP are comparatively investigated on the basis of scanning electronic microscopy (SEM) and thermogravimetric analysis (TGA). Results show that the as‐prepared POSS‐based polymeric materials exhibit a higher glass transition temperature than that of pure PNMA, ascribing to modified POSS well‐dispersed in these hybrid polymers. Also, the products with different microstructures display different thermal properties. The pure PNMA exhibits a featureless morphology, whereas a hierarchical morphology is obtained for the POSS‐based polymeric materials. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1136–1147, 2009     

Spontaneous Cu(I)Br–PMDETA‐mediated polymerization of isobornyl methacrylate in heterogeneous aqueous medium at ambient temperature

Isobornyl methacrylate (IBMA), a bulky hydrophobic methacrylate, undergoes very fast polymerization, in bulk, with Cu(I)Br/N,N,N′,N″,N″‐pentamethyldiethylenetriamine (PMDETA)/ethyl‐2‐bromoisobutyrate system, at ambient temperature. IBMA also undergoes a spontaneous initiator‐free polymerization, at ambient temperature, with Cu(I)Br/PMDETA catalytic system in dimethyl sulfoxide–water mixtures. The rate of the polymerization is seen to increase with the water content up to 80 mol % of water. A possible intervention of air in initiation is proposed. The active Cu(0) formed by the disproportionation of Cu(I) species in aqueous medium probably plays a vital role for a possible air‐initiation of IBMA via single electron transfer‐living radical polymerization (SET‐LRP) mechanism. A high tolerance level to water under SET‐LRP conditions is demonstrated. The poly(IBMA) samples obtained exhibit low molecular weight distributions (1.1–1.3). Similar behavior was not observed with other common methacrylates such as methyl methacrylate, t‐butyl methacrylate, cyclohexyl methacrylate, and benzyl methacrylate. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis of polynorbornene‐poly(tert‐butyl acrylate) nanoparticles with original morphologies by tandem ROMP and ATRP in microemulsion

Composite latex particles based on homopolymers and graft‐copolymers composed of polynorbornene (PNB) and poly(tert‐butyl acrylate) (PtBA) were synthesized in microemulsion conditions by simultaneous combination of two distinct methods of polymerization: Ring‐opening metathesis polymerization (ROMP) and atom transfer radical polymerization (ATRP). Only one commercial compound (first generation Grubbs catalyst) was used to initiate the ROMP of norbornene (NB) and activate the ATRP of tert‐butyl acrylate (tBA). Well‐defined nanoparticles with hydrodynamic diameters smaller than 50 nm were prepared with original morphologies depending on the monomer compositions, the type of combination (polymer blend or graft‐copolymer), and the conditions of microemulsion polymerizations. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Facile synthesis of N‐vinylimidazole‐based hydrogels via frontal polymerization and investigation of their performance on adsorption of copper ions

We report a new facile strategy for quickly synthesizing pH sensitive poly(VI‐co‐HEA) hydrogels (VI = N‐vinylimidazole; HEA = 2‐hydroxyethyl acrylate) by frontal polymerization. The appropriate amounts of VI, HEA, and ammonium persulfate (APS)/N,N,N′,N′‐tetramethylethylenediamine (TMEDA) couple redox initiator were mixed together at ambient temperature in the presence of glycerol as the solvent medium. Frontal polymerization (FP) was initiated by heating the upper side of the mixture with a soldering iron. Once initiated, no further energy was required for the polymerization to occur. The dependence of the front velocity and front temperature on the VI/HEA weight ratios were investigated. The pH sensitive behavior, morphology, and heavy metal removal study of poly(VI‐co‐HEA) hydrogels prepared via FP were comparatively investigated on the basis of swelling measurements, scanning electron microscopy, and inductively coupling plasma spectrometer. Results show that the poly(VI‐co‐HEA) hydrogels prepared via FP exhibit good pH sensitivity and adsorption capacity. The FP can be exploited as an alternative means for synthesis of pH sensitive hydrogels in a fast and efficient way. The as‐prepared hydrogels can be applied to remove heavy metals. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 4005–4012, 2010     

Poly(p‐phenylene methylene)‐based block copolymers by mechanistic transformation

The synthesis of poly(p‐phenylene methylene) (PPM)‐based block copolymers such as poly(p‐phenylene methylene)‐b‐poly(ε‐caprolactone) and poly(p‐phenylene methylene)‐b‐polytetrahydrofuran by mechanistic transformation was described. First, precursor PPM was synthesized by acid‐catalyzed polymerization of tribenzylborate at 16 °C. Then, this polymer was used as macroinitiators in either ring‐opening polymerization of ε‐caprolactone or cationic ring‐opening polymerization of tetrahydrofuran to yield respective block copolymers. The structures of the prepolymer and block copolymers were characterized by GPC and ¹H NMR investigations. The composition of block copolymers as determined by ¹H NMR and TGA analysis was found to be in very good agreement. The thermal behavior and surface morphology of the copolymers were also investigated, respectively, by differential scanning calorimetry and atomic force microscopy measurements, and the contribution of the major soft segment has been observed. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Semi‐interpenetrating polymer networks of methyl cellulose and polyacrylamide prepared by frontal polymerization

In this study, the feasibility of frontal polymerization (FP) as an alternative and convenient technique for the preparation of semi‐interpenetrating polymer networks made of methyl cellulose (MC) and cross‐linked polyacrylamide (PAAm) is demonstrated. FP was performed in water and glycerol, as largely available, nontoxic solvents. Although FP occurred in both media, differences were found by comparing the samples made in the two solvents. In particular, those prepared in water are characterized by larger inhomogeneity and less reproducibility, thus accounting for the boiling effects that influence propagating polymerization fronts when water was used. The effects of the ratio among MC and PAAm, the amount of cross‐linker and solvent medium were studied in terms of influence on temperature and velocity of FP fronts, glass transition temperature (dried samples), swelling behavior, dynamic‐mechanical properties (gels swollen in both water or glycerol), and tensile behavior. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 55, 1268–1274     

Solvent‐free free‐radical frontal polymerization: A new approach to quickly synthesize poly(N‐vinylpyrrolidone)

The first synthesis of poly(N‐vinylpyrrolidone) without solvent by free‐radical frontal polymerization at ambient pressure is reported. The appropriate amounts of two reactants N‐vinyl‐2‐pyrrolidone (NVP) and initiator 2,2′‐azobis‐isobutyronitrile (AIBN) without solvent were mixed together at ambient temperature. Frontal polymerization was initiated by heating the wall of the tube with a soldering iron, and the resultant hot fronts were allowed to self‐propagate throughout the reaction vessel. Once initiated, no further energy was required for polymerization to occur. To suppress the fingers of molten monomer, a small amount of nanosilica was added. The dependence of the front velocity and front temperature on the AIBN concentration was thoroughly investigated. The as‐prepared polymers were characterized by gel permeation chromatography (GPC) and thermogravimetric analysis (TGA). Results show that without postpolymerization solvent removal, waste production can be reduced. Solvent‐free FP could be exploited as a means for preparation of PVP with the potential advantage of higher throughput than solvent‐based methods. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2177–2185, 2008     

Frontal polymerization for smart intrinsic self‐healing hydrogels and its integration with microfluidics

Frontal polymerization (FP) is applied for the synthesis of β‐cyclodextrin/poly(vinylimidazole‐co‐N‐vinylcaprolactam‐co‐acrylic acid) (β‐CD/P(VI‐co‐NVCL‐co‐AA)) copolymers. The dependence of frontal velocity and temperature on the initiator and cross‐linker are discussed. The synthesized copolymers have been characterized by Fourier transform infrared (FTIR), thermogravimetric analysis (TGA), and scanning electron microscopy (SEM). The thermo‐pH dual‐stimuli responsive behavior of the hydrogel is determined by swelling measurement at different temperatures and pH values. Besides, the hydrogels show intrinsic self‐healing behavior and their healing efficiency is determined by the mechanical tests. Interestingly, we integrate FP with microfluidic technology, which may realize the execution of FP under continuous condition. Such simple microfluidics‐FP integrated approach has both methodological and practical value for the synthesis of functional materials. This paper mainly presents the synthesis and characterization of β‐cyclodextrin/poly(vinylimidazole‐co‐N‐vinylcaprolactam‐co‐acrylic acid) (β‐CD/P(VI‐co‐NVCL‐co‐AA)) copolymers by using thermal frontal polymerization (TFP). Hydrogels were found to be self‐healing with good mechanical performance and show dual thermo‐pH responsive behavior. Low‐cost, energy‐saving and efficient method of thermal frontal polymerization process was integrated with microfluidics technology to prepare supraball hydrogel. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1412–1423     

R‐RAFT approach for the polymerization of N‐isopropylacrylamide with a star poly(ε‐caprolactone) core

Reversible addition‐fragmentation chain transfer (RAFT) polymerization is a more robust and versatile approach than other living free radical polymerization methods, providing a reactive thiocarbonylthio end group. A series of well‐defined star diblock [poly(ε‐caprolactone)‐b‐poly(N‐isopropylacrylamide)]₄ (SPCLNIP) copolymers were synthesized by R‐RAFT polymerization of N‐isopropylacrylamide (NIPAAm) using [PCL‐DDAT]₄ (SPCL‐DDAT) as a star macro‐RAFT agent (DDAT: S‐1‐dodecyl‐S′‐(α, α′‐dimethyl‐α″‐acetic acid) trithiocarbonate). The R‐RAFT polymerization showed a controlled/“living” character, proceeding with pseudo‐first‐order kinetics. All these star polymers with different molecular weights exhibited narrow molecular weight distributions of less than 1.2. The effect of polymerization temperature and molecular weight of the star macro‐RAFT agent on the polymerization kinetics of NIPAAm monomers was also addressed. Hardly any radical–radical coupling by‐products were detected, while linear side products were kept to a minimum by careful control over polymerization conditions. The trithiocarbonate groups were transferred to polymer chain ends by R‐RAFT polymerization, providing potential possibility of further modification by thiocarbonylthio chemistry. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Facile synthesis of poly(DMC‐co‐HPA) hydrogels via infrared laser ignited frontal polymerization and their adsorption–desorption switching performance

In this work, we report a versatile infrared laser ignited frontal polymerization technique for the fabrication of a series of poly(DMC‐co‐HPA) hydrogels (DMC = methacryloxyethyltrimethyl ammonium chloride, HPA = hydroxypropyl acrylate). Because the method is based on the exothermic reaction, no further energy is required in the reaction once it is initiated. Moreover, we have found the polymerization process is a pure frontal polymerization model without involving any other reaction process. The dependence of frontal velocity and temperature on the reaction time is thoroughly discussed. The as‐prepared hydrogels are pH‐responsive and their maximum equilibrium swelling ratio could reach ～3,890%. Also, the as‐prepared poly(DMC‐co‐HPA) hydrogels capable of adsorption/desorption switching performance can be utilized for heavy metal ion removal in wastewater treatments. Interestingly, the hydrogels can float on the water surface after intaking heavy metal ions by the combination of kerosene and polyoxyethylene sorbitan monolaurate (Tween 20) in hydrogel components, greatly enhancing treatment efficiency. We believe the method described herein to rapidly construct functional hydrogels with the ability to remove heavy metal ions may find unique applications in emergency processing of water pollution. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2085–2093     

Photo‐triggered redox frontal polymerization: A new tool for synthesizing thermally sensitive materials

A novel approach of photo‐triggered redox frontal polymerization (FP) by integrating photocaged superbase (QA‐DBU) with a peroxide initiator (dibenzoyl peroxide, BPO) is presented for the synthesis of thermally sensitive materials. Under photo‐irradiation at a localized region, the regenerated superbase can diffuse into unirradiated regions and effectively actuate redox FP in a diffusion‐controlled manner. Moreover, the redox FP can be conducted at a much lower front temperature with enhanced front velocity. Astonishingly, the front temperature can be well‐modulated by changing the concentration of latent superbase. The prepared thermally sensitive fluorescent polymer composites exhibit enhanced fluorescence emission intensity compared to that of conventional thermal FP. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4515–4521     

A facile pathway for the fast synthesis of colloidal crystal‐loaded hydrogels via frontal polymerization

In this work, a dually sensitive colloidal crystal (CC)‐loaded hydrogel has been synthesized via frontal polymerization (FP) in a facile and rapid way. First, a polystyrene CC film was fabricated by vertical deposition on the inner wall of a test tube. Then, a mixture of acrylic acid (AAc), 2‐hydroxyethyl methacrylate (HEMA), and glycerol along with the initiator and crosslinker was added to this test tube to carry out FP, resulting in the formation of CC‐loaded hydrogel. The influence of the mass ratios of HEMA/AAc on front velocity and temperatures were studied. The swelling behavior, the morphology, and the stimuli‐responsive behavior of the CC‐loaded hydrogels prepared via FP were thoroughly investigated on the basis of swelling measurement, scanning electron microscopy, and reflection spectra. Results show that the as‐prepared CC‐loaded hydrogels exhibit excellent dual sensitivity to both methanol concentrations and pH values with very short response time, which can be observed visually without the aid of instruments. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Effects of hydration and hydrophilicity on Na‐Clay‐supported aqueous‐phase catalysis for atom transfer radical polymerization

Hydrated sodium montmorillonite (Na‐clay) has been used as a catalyst support for the heterogeneous atom transfer radical polymerization of benzyl methacrylate in the presence of various concentrations of water, reducing agent, and CuBr₂ in anisole at ambient temperature. The polymerization was promoted via reduction of Cu^II to Cu^I through the addition of sodium ascorbate (NaAsc) as a reducing agent in aqueous solution. The polymerizaton proceeded in a controlled manner and produced poly(benzyl methacylate) with moderately narrow molecular weight distribution (MWD) when performed under optimum conditions of hydration (10 wt % ≤ H₂O/Na‐clay ≤ 21 wt %) and reducing agent (0.15 ≤ [NaAsc]/[I] ≤ 0.23). The polymerization was uncontrolled if hydration and NaAsc exceed above their optimum range of concentrations. Apparent rate of the polymerization (k_app) increased in the presence of decane–anisole (1/3, v/v) mixture solvent. Selective adsorption of decane at the interfaces of the hydrated clay was attributed for the rate enhancement due to increased polymer and hydrophobic interface interaction. The polymerization progressed in a controlled manner as confirmed by the first‐order time‐conversion plot, linear increase in molecular weights, and moderately narrow MWDs over conversion. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis of versatile poly(PMMA‐b‐VI) macromonomer‐based hydrogels via infrared laser ignited frontal polymerization

In this work, poly((PMMA‐b‐VI)‐co‐AA) (MMA = methyl methacrylate; VI = 1‐vinylimidazole; AA = acrylic acid) hydrogels and poly((PMMA‐b‐VI)‐co‐AA)/TPU (TPU = thermoplastic polyurethane) IPN (interpenetrating polymer networks) hydrogels have been fabricated via versatile infrared laser ignited frontal polymerization by using poly(PMMA‐b‐VI) macromonomer as the mononer. The frontal velocity and T_max (the highest temperature that the laser beam detected at a fixed point) can be adjusted by varying monomer weight ratios, the concentration of BPO (BPO = benzoyl peroxide) and the amount of TPU. Moreover, the addition of TPU enhances the reactant viscosity to suppress the “fingering” of frontal polymerization (FP) and decrease T_max of the reaction, providing a new inert carrier (TPU) to assist FP. Through the characterization of Fourier transform‐infrared spectroscopy (FT‐IR), scanning electron microscope (SEM), and differential scanning calorimetry (DSC), the desired structure can be proved to exist in the IPN hydrogels. Furthermore, poly((PMMA‐b‐VI)‐co‐AA)/TPU IPN hydrogels possesses more excellent mechanical behaviors than hydrogels without IPN structure. Besides, the poly((PMMA‐b‐VI)‐co‐AA) hydrogels present splendid sensitive properties toward substances of different flavor including sourness (CA, citric acid or GA, gluconic acid), umami (SG, sodium glutamate), saltiness (SC, sodium chloride), sweetness (GLU, glucose), enabling their potential as artificial tongue‐like sensing materials. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1210–1221